HL-lM装置杂质粒子输运与约束特性

在HL-lM装置上利用激光吹气技术,在等离子体边缘瞬态注入少量Al杂质粒子,通过对真空紫外光谱和软X射线区的杂质辐射测量,分别研究了欧姆等离子体和低杂波电流驱动等离子体两种情况下,Al杂质粒子输运与约束特性。结果表明：在欧姆等离子体和低杂波电流驱动等离子体两种情况下,等离子体中心区,在没有MHD锯齿震荡和有MHD锯齿震荡非锯齿破裂期间,杂质粒子输运基本上受新经典规律支配;在有MHD锯齿震荡锯齿破裂期间,杂质粒子输运受MHD不稳定性支配,但其时间很短(通常小于300μs),所以在这种情况下,杂质粒子输运的平均效应比新经典值稍大。而约束区杂质粒子输运则比新经典的值大很多,是反常的。在一定条件下低混杂波电流驱动可以改善等离子体粒子约束。     

LHCD期间HL—1M等离子体密度的锯齿现象

利用ＨＣＮ激光多道干涉仪,首次在ＨＬ－１Ｍ装置上在低混杂电流驱动期间观测到密度锯齿现象。分析表明,密度锯齿不是通常的ｑ＝１锯齿,而是低混杂波与杂质共同作用下的产生的ｑ〉１的锯齿。     

HL－1M感应与低杂波组合电流驱动研究

本文结合ＨＬ－１Ｍ的基本参数，利用准线性的低杂波电流驱动理论和等离子体的电回路方程．研究了在控制等离子体总电流不变情形下欧姆感应和低杂波注入组合驱动电流的问题。结果表明，这一组合驱动方案对ＨＬ－１Ｍ装置的运行是可行的，其驱动电流分布可以通过改变低杂波注入功率、波谱形状、等离子体电子温度、密度以及总等离子体电流等加以控制。组合驱动的电流分布将优于欧姆驱动的电流分布，并可能抑制诸如锯齿振荡等一些ＭＨＤ不稳定性。     

低混杂波电流驱动下注入杂质的输运

在欧姆放电和低混杂波电流驱动条件下,应用激光吹气技术注入金属杂质,用真空紫外谱仪测量了杂质线的辐射,给出了ＨＬ－１Ｍ 装置欧姆等离子体和低混杂波电流驱动等离子体杂质输运的研究结果。用杂质输运程序ＬＢＯ进行数值模拟,得出了等离子体中杂质的扩散系数Ｄ（ｒ） 和对流速度ｖ（ｒ）。在低混杂波电流驱动条件下,等离子体杂质的输运系数相对欧姆放电等离子体杂质的输运系数减小了５０％ 左右。结果表明,在ＨＬ－１Ｍ 装置上低混杂波电流驱动等离子体相对通常欧姆等离子体杂质的约束性能明显得到了改善     

HL—1M装置几种杂质谱线的特性

介绍了ＨＬ－１Ｍ装置真空紫外光谱区的杂质辐射观测结果。对器壁硅化后的杂质特性进行了分析，用激光吹气技术研究了杂质输运，分析了低混杂波电流驱动、弹丸注入实验中杂质谱线的变化。     

HT-7低杂波电流驱动效率与有效电荷数及电子温度的关系

在HT-7超导托卡马克中进行了低杂波电流驱动的功率扫描实验,功率变化范围为100kW至700kW,频率为2.45GHz。研究了等离子体平均有效电荷数及电子温度与低杂波功率之间的关系。给出了不同功率下低杂波电流驱动效率与有效电荷数及电子温度之间的关系:HT-7装置低杂波驱动效率与电子温度成正比,与有效电荷数成反比。指出了动态杂质控制是改善低杂波电流驱动效率的关键问题。     

HT-7装置软X射线诊断系统及锯齿行为研究

利用HT-7装置上建立的多阵列软X射线诊断系统对等离子体放电中的锯齿不稳定性进行研究,发现锯齿的出现及其行为特点与等离子体电子密度N_e、电子温度T_e、边界安全因子q_α、壁条件等放电参数有密切关系。在低杂波电流驱动等离子体放电条件下,观察到m/n=1/1的中间模振荡出现在锯齿的上升阶段,并迅速发展、饱和、衰减,在锯齿塌陷或先兆振荡出现以前消失。分析和讨论了欧姆加热条件下和低杂波加热条件下的锯齿行为。     

托卡马克等离子体环向电流的锯齿效应

本文从动力论出发，分析了在托上瞳马克欧姆感应驱动和低杂波驱动等离子体的组合放电中，锯齿崩塌时，循环电子和俘获电子对环向电流及其密度产生的调制作用。     

HL-1M装置中的离轴电子回旋加热实验

在HL-1M装置上进行了离轴电子回旋加热实验。研究了电子温度的变化，等离子体密度对加热效果的影响，离轴加热条件下MHD锯齿的变化，波对m/nk=1/1模的影响及在与低杂波电流驱动共同作用下的各种实验现象。 这些现象被认为与高能电子和它们的分布有关。     

EAST���Ӳ�������������ֵģ��

应用改进后的低杂波电流驱动程序对EAST进行了低杂波电流驱动的数值模拟。通过模拟发现,波注入位置、功率谱、等离子体温度和密度对低杂波的功率沉积和电流驱动剖面分布有很大影响。通过选取合适的低杂波功率谱、等离子体温度和密度,可以实现对其功率沉积和电流驱动剖面分布的控制。     

Sawtooth-like electron density oscillations under laser blow-off and lower hybrid current drive in HL-1M tokamak

By using of a six-channel HCN laser interferometer, the sawtooth-like density oscillations without being exhibited in the ohmic phase plasma have been observed during lower hybrid current drive (LHCD) discharges in the HL-1M device. There are often accompanied by injected impurity with laser blow-off. Analyses show that this kind of density sawtooth-like oscillation comes from the mutual effect of LHCD and impurity. An available mechanism is the loss of superthermal electrons by the magnetic perturbation, which is caused by the crash of the central accumulated impurities.     

Compound sawtooth in EAST LHCD plasma:An experimental study

A compound sawtooth with an incomplete relaxation was observed in EAST’s lower hybrid current drive(LHCD)plasma. The sub-crash phase of the compound sawtooth corresponds to a longer-lasting and slower-growing 1/1 mode.Based on the two-dimensional(2D) SXR tomography, the time-dependent 2D image of a compound sawtooth crash is obtained. The island produced during a resistive internal kink mode is observed in the all crash phases of the compound sawtooth. The destabilization of 1/1 long-lasting saturated 1/1 mode is related to the current driven by the LHCD near the q = 1 surface.     

HL─1装置等离子体输运与锯齿特性的数值研究

本文利用一维圆柱等离子体输运编码（ＴＲＡＮＰＹ），编制了模拟锯齿振荡的大型编码（ＳＡＷＭＯＤ）。对锯齿振荡的研究，我们选用了两种具有代表性的理论模型：重联模型和湍流模型，后者特别适用于低ｑａ放电的锯齿特性研究。重联模型的锯齿振荡是由于磁力线的完全重联引起的，而湍流模型的锯齿振荡是因为微观湍流或磁力线的随机化而产生的。最后，我们将ＨＬ─１装置的一次典型高密放电的参数代入（ＳＡＷＭＯＤ）编码，运算结果表明，重联模型和湍流模型均能解释实验观测的锯齿现象，理论模拟与实验结果符合较好。     

Investigation of Impurity Ion Transport with Laser Blow-off in HL-2A Tokamak

Non-recycling impurities are injected into ohmic HL-2A plasma for the first time. The impurities of titanium and aluminium are injected in the discharges with varying plasma density and current. The convection and diffusion process of the injected impurity ions during the inward phase are qualitatively investigated. The results show that the transport of impurities is much slower in the central region of the plasma than outside of it and that it is greatly enhanced during sawtooth crashes.     

Radial scanning diagnostics of bremsstrahlung and line emission in T-10 plasma

The paper describes the scanning spectroscopic diagnostics designed for measurement of line integrated plasma radiation in two visible spectral ranges. This diagnostic system is aimed at measuring the bremsstrahlung absolute values and profile with high spatial resolution. The bremsstrahlung absolute values are used to determine the value and radial distribution of effective plasma ion charge Z _eff(r) in T-10 discharges. The importance of Z _eff measurement is due to its strong influence on plasma heating, confinement, and stability. The spatial distribution of emission for one of the chosen spectral lines is measured simultaneously with bremsstrahlung. The spatial resolution of measurements is ~1 cm, and the temporal resolution is up to 10 ms. The spectral equipment and methods for its calibration are described. Examples of line integrated brightness distribution in a “continuum window” of 5236 ± 6 Å and brightness of the lines C⁵⁺ (5291 Å), He¹⁺ (4686 Å), and D_β (4861 Å) are given. Flattening of the bremsstrahlung brightness profile in the central region of the plasma column in some discharges with sawtooth oscillations in the T-10 is observed. The measured effective ion charge profiles in ohmic discharges with high plasma density and low discharge currents demonstrate accumulation of light impurities at the column axis; as a consequence, quenching of sawtooth oscillations in some discharges is observed. The developed diagnostics provides necessary data for investigation of heat, particle, and current transport in the plasma of the T-10. Successful application of the obtained data on Z _eff(r) for investigation of geodesic acoustic modes of plasma oscillations in the T-10 should be specially noted.     

小波变换在HT-7 Tokamak磁流体动力学振荡动态频谱分析中的应用

将Gauss复小波变换方法成功地应用于HT-7Tokamak磁流体动力学振荡动态频谱分析中.研究结果表明,这种方法具有较好的时间分辨率和空间分辨率,比较适用做动态频谱分析.对典型放电数据的分析结果表明, m=1模的振荡频率与等离子体压强梯度有着密切的关系.     

Heat Flux on EAST Divertor Plate in H-mode with LHCD/LHCD+NBI

Based on the surface temperature measured by the infrared camera on the experimental advanced superconducting tokamak(EAST), the heat fluxes on the lower outer divertor target plate during H-mode with the lower-hybrid wave current drive(LHCD) only and with the LHCD combined with the neutral beam injection(NBI) are calculated by the DFLUX code and compared. The analyzed discharges are lower single null divertor configuration discharges. In the case with the LHCD only(I_p~400 kA, P_(LHCD)~2 MW), ELM-free appears after L-H transition with the peak heat flux on the lower outer target plate less than 1 MW/m2. However, there is no ELMfree appearing after the L-H transition in the case with the LHCD+NBI(I_P~300 kA, P_(LHCD)+P_(NBI)~2 MW).The results show that the peak heat fluxes on the lower outer target plate in the LHCD+NBI H-mode cases are larger than those in the LHCD H-mode under the similar auxiliary heating power. This is because the heat flux profiles of the lower outer target plate as a function of plate location in ELMing with the LHCD+NBI are narrower than those with the LHCD only. The results are consistent with the results in terms of the scrape-off layer width observed in the EAST.     

Observation of Runaway Electron Behaviour During Disruptions in LHCD Discharges in the HT‐7 Tokamak

Production of runaway electrons during disruptions has been observed in the HT‐7 Tokamak. The runaway current plateaus, which can carry part of the pre‐disruptive current, are observed in lower‐hybrid current drive (LHCD) limiter discharges. It is found that the runaway current can mitigate the disruptions effectively. We can use gas puffing to increase the line‐averaged density to restrain the runaway electrons and rebuild the plasmas after the disruptions. Detailed observations are presented on the runaway electrons generated following disruptions in the HT‐7 tokamak discharges. The results indicate that the magnetic oscillations play a significant role in the loss of runaway electrons in disruptions. There are two important preconditions to rebuild plasmas by runaway electrons after the disruptions. One of them are weak magnetic oscillations; another one are LHWs (lower‐hybrid waves) (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)