含特异材料光子晶体隧穿模的偏振特性

构造了由普通材料A(SiO₂)和电单负材料B组成的(AB)^N(BA)^N型一维光子晶体.数值计算表明原禁带的1907.3 nm处出现了一个十分尖锐的隧穿模. 入射角增加,该隧穿模的透射率和半峰全宽度均保持不变,但位置发生蓝移, 入射角在15°-65°的区间内,移动率的绝对值 |dλ/dθ| 较大.当B介质的磁导率μ_B 从5增加到10时,只是隧穿模的位置发生了红移. 介质的几何厚度增加时,隧穿模的透射率不变,但其位置红移明显,半峰全宽略有增加.     

一维三元光子晶体缺陷模的特性研究

在考虑色散关系的基础上,利用传输矩阵法讨论了一维三元光子晶体缺陷模的特征.结果表明:缺陷层几何厚度增加时,缺陷模中心红移,透射率下降,品质因子变小.三介质的几何厚度各自独立递增时,缺陷模都向长波方向移动,缺陷模的品质因子先增后降.入射角增大时,缺陷模中心蓝移,透射率不变,半峰全宽度变窄,品质因子变小.若忽略缺陷介质的色散,当其折射率减小时,缺陷模蓝移,透射率变大,半峰全宽度保持不变,品质因子增大.     

一维光子晶体缺陷模偏振特性的研究

利用一维光子晶体的透射率公式,计算出一维光子晶体掺杂后TE波和TM波缺陷模的波长随入射角的响应曲线、缺陷模透射峰随入射角的响应曲线、缺陷模透射峰随入射波长的响应曲线.研究发现,TE波和TM波的缺陷模透射峰均随入射角的增加而向短波方向移动；TE波缺陷模透射峰的半高宽度(FWHM)和峰值随入射角的增加而减小,而TM波缺陷模透射峰的半高宽度(FWHM)和峰值确随入射角的增加而增加；对TM波其波长为λ0的缺陷模也存在明显的“广义布儒斯特角”现象, TE波的缺陷模不存在“广义布儒斯特角”现象.     

一维光子晶体全反射隧穿的色散特性

利用介质材料的色散关系和特征矩阵法研究了一维光子晶体中TE波和TM波的全反射隧穿效应随色散的变化特征.TE波和TM波全反射隧穿导带的频率中心随色散强度的增加而降低,频率宽度随色散强度的增加而增大.TE波和TM波的全反射隧穿导带的频率中心随入射角的增加而升高,频率宽度随入射角的增加而减小.这些研究结果拓宽了对一维光子晶体中TE波和TM波波全反射隧穿效应的认识.     

单负材料一维光子晶体超窄带滤波特性研究

用传输矩阵法研究了单负材料一维光子晶体(ABD)m(CBA)n(ABD)m(CBA)n的透射谱。结果表明:当增加周期数m或D层介质厚度dD时,透射谱中的两个隧穿模越加锋锐,但所处频率位置不变;当增加周期数n或C层介质厚度dC时,透射谱中的两个隧穿模向中间靠拢趋于简并;当增加A层介质厚度dA时,透射谱中双隧穿模结构及位置无变化,而当增加B层介质厚度dB时,透射谱中的三模结构向低频方向移动,且逐渐消失;随着入射角θ的增大,透射谱中两隧穿模向禁带中心靠拢。利用单负材料光子晶体的透射谱特性可实现可调性和高品质的单、多通道超窄带滤波功能。     

由单负材料组成的一维对称型光子晶体中的隧穿模

由电单负材料A和磁单负材料B构成了一维对称型光子晶体,数值计算表明其带隙中出现了一隧穿模. 材料层数增加,隧穿模宽度急剧变窄,而其位置不变.隧穿模的位置和宽度对入射角的变化都不太敏感. 材料的几何厚度减小,隧穿模的位置蓝移,而其宽度不变. μ_A, ε_B增加,隧穿模的位置红移,宽度减小. 利用隧穿模的以上特性可以实现对电磁波传播的动态调控.     

含复折射率介质一维准周期光子晶体的透射特性

用Si和复折射率介质构成了(AB)N型一维准周期光子晶体,在考虑Si色散关系的基础上,利用传输矩阵法研究了其透射特性.数值计算表明其TE波的透射谱有如下特征:电磁波垂直入射时,在相对频率0～4的范围内存在4个等间距的尖锐的透射主峰,各主峰低频端相距0.148 (ω/ω0)处都有一透射副峰.入射角增加,主峰的透射率下降,副峰的透射率上升.周期数N增加,各主、副峰位置都有蓝移,但主峰透射率逐渐减小,而各副峰的半峰全宽度变小.当两介质厚度为定值时,从第一主峰到第四主峰,其透射率依次减小,两介质厚度增加时,各主峰的透射率下降.复折射率虚部增加时,各透射峰的位置保持不变,主峰的透射率变大,而副峰的透射率变小,反之亦然.     

含负折射率层的多层体系的反常光子隧穿

研究了多层体系含负折射率层的光学传输特性,通过传输矩阵方法,给出了体系透射率的一般表达式,并讨论了含负折射率层的四层结构在入射角大于临界角时的反常光子隧穿现象。当体系参量完全匹配时,对于任意入射光波长及大于临界角的入射,透射率均为1;仅衬底层不匹配时,对于给定的衬底参量,透射率和入射波长无关,仅和入射角相关。对于TM波,存在多层体系的布儒斯特角,使得透射率等于1。对于TE波则没有类似现象;在衬底不匹配的情况下,提高出射端的折射率将增加体系的透射率;中间层的厚度或者折射率不匹配时,透射率关于匹配位置对称分布且随着失谐的增加指数衰减,随着入射角的增加,衰减速度加快。     

各向异性光子晶体的全反射隧穿偏振特性

为了研究一维各向异性光子晶体的全反射隧穿偏振特性,利用传输矩阵法计算了TE波和TM波以大于全反射角入射一维各向异性光子晶体时的透射率,在透射波中发现了TE波和TM波的一、二级全反射隧穿带.得出了与一维各向同性光子晶体的全反射隧穿效应的不同点,即TE波和TM波的一、二级全反射隧穿带的频率中心和频率宽度存在着较大的差异,利用这个特性可以将两种偏振光进行频率分离,为设计优质偏振滤波器提供理论依据.     

RTCM算法在一维光子晶体缺陷模中的应用

利用RTCM算法研究一维光子晶体的缺陷模.研究了TE波和TM波入射时的情况,通过改变杂质层的光学厚度以及杂质层的折射率从而得出一些有重要指导意义的缺陷模特性.同时对有缺陷的一维光子晶体在窄带滤波器中的应用做了一定程度的探讨.结果表明:正入射时,TE波和TM波的透射率几乎相同,随着杂质层光学厚度的增加,透射峰数目增加,这有助于制作多道窄带滤波器.因此,有缺陷的一维光子晶体可以制作波分复用中的多道滤波器.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.