气体分子在石墨表面的吸附与扩散特性

采用分子动力学方法模拟研究气体分子在石墨表面上的吸附和扩散特性,结果表明气体分子在石墨表面上的吸附强度跟石墨中碳原子和气体分子之间的微观作用力密切相关,不同分子在石墨表面上的吸附强度不同。气体分子在石墨表面上的吸附特性符合Langmuir等温吸附模型,压力越高吸附层内分子的密度越高。通过分子的表面扩散系数随着压力的增加而降低的现象以及特定时间内分子运动距离的正常概率分布,发现石墨表面上分子的扩散主要由分子之间的碰撞控制,趋近于体相扩散。分子在石墨表面吸附层内的密度对表面扩散系数的影响非常显著,导致吸附性强的CO_2和H_2S分子扩散系数要明显低于吸附性弱的CH_4和N_2分子.     

印尼褐煤经溶剂提质后理化特性的变化规律

分析印尼褐煤经乙醇和正己烷两种有机溶剂加压提质后理化特性的变化规律。在反应温度为300℃,压力为17MPa时,褐煤经乙醇提质后的固体产率为65.1%;在反应温度为300℃,压力为12 MPa时,褐煤经正己烷提质后的固体产率为74.4%。提质后褐煤的O/C和H/C降低,热值大幅度提高,煤阶升高。提质后褐煤表面产生较多微孔和大孔,且随着反应温度的增加,小孔数量减少,大孔数量增加。提质后褐煤中羧基、羰基、羟基等含氧官能团大幅度减少,芳香环缩合程度增加。在反应温度为300℃下,褐煤中的羰基所含比例由原煤19.42%分别下降到5.72%(乙醇提质)和2.04%(正己烷提质),而羧基已经全部分解。     

异性官能团修饰石墨烯吸附GIS 特征气体能力的DFT研究

为研制高灵敏度气体绝缘组合开关(GIS)特征气体检测传感器,利用密度泛函理论方法,采用分子模拟软件对GIS特征气体(SO_2,SOF_2,SO_2F_2,CF_4)在异性官能团(羟基、羧基与氨基)修饰石墨烯表面的吸附过程进行模拟计算,从微观角度研究了GIS特征气体在异性官能团修饰石墨烯表面的吸附机理.首先计算了各吸附体系的吸附能、净电荷转移量以及态密度,比较了羟基与羧基修饰石墨烯对GIS特征气体的吸附能力;再通过分子前线轨道与能隙对吸附能力强弱的机理进行了研究,得出强吸附修饰官能团的规律性特征,并通过氨基石墨烯进行验证.结果表明:羧基与羟基修饰石墨烯能够有效提高对SO_2,SOF_2,SO_2F_2的吸附能力,但羧基石墨烯对GIS特征气体的整体吸附能力更强;异性官能团修饰石墨烯后的能隙及其与气体分子前线轨道能量差越小,对GIS特征气体吸附能力就越强,异性官能团修饰石墨烯的能隙与前线轨道能量差可以作为选择特征气体敏感材料的依据.     

异性官能团修饰石墨烯吸附GIS特征气体能力的DFT研究

为研制高灵敏度气体绝缘组合开关(GIS)特征气体检测传感器，利用密度泛函理论方法，采用分子模拟软件对GIS特征气体(SO_2,SOF_2,SO_2F_2,CF_4)在异性官能团(羟基、羧基与氨基)修饰石墨烯表面的吸附过程进行模拟计算，从微观角度研究了GIS特征气体在异性官能团修饰石墨烯表面的吸附机理.首先计算了各吸附体系的吸附能、净电荷转移量以及态密度，比较了羟基与羧基修饰石墨烯对GIS特征气体的吸附能力;再通过分子前线轨道与能隙对吸附能力强弱的机理进行了研究，得出强吸附修饰官能团的规律性特征，并通过氨基石墨烯进行验证.结果表明:羧基与羟基修饰石墨烯能够有效提高对SO_2,SOF_2,SO_2F_2的吸附能力，但羧基石墨烯对GIS特征气体的整体吸附能力更强;异性官能团修饰石墨烯后的能隙及其与气体分子前线轨道能量差越小，对GIS特征气体吸附能力就越强，异性官能团修饰石墨烯的能隙与前线轨道能量差可以作为选择特征气体敏感材料的依据.     

锂离子进入碳纳米管端口速度的分子动力学模拟

锂离子进入碳纳米管端口的速度V Li是影响锂离子电池充电性能的重要因素.采用分子动力学模拟方法,研究了直径、温度、电场强度和端口改性官能团四种因子对其影响.运用正交实验方法,分析得出了各因子及其不同水平的影响规律.结果表明,四种因子的影响力度由大到小依次为:电场强度、官能团类型、碳纳米管直径和温度.在本文的模拟条件下,随着电场强度和碳纳米管直径的增大,V Li逐渐增加,且在电场强度下的增幅会更显著;碳纳米管端口官能团分别改性为氢原子(—H),羟基(—OH),氨基(—NH2)以及羧基(—COOH)时,V Li会逐步降低;随着温度的增大,V Li先增加后减小,但整体波动偏幅不大.     

活性炭表面含氧官能团对汞吸附的作用

本文对采用不同方法处理后的活性炭进行BET、官能团分析和汞吸附性能实验,研究其表面含氧官能团对汞吸附的作用。结果表明:活性炭表面的酯基与羰基能提高汞的吸附效率,高于100℃时是影响活性炭汞吸附效率的主要因素。物理吸附,羰基与酯基吸附的汞的程序升温脱附温度峰值分别为100,210和320℃。汞在与活性炭表面接触后优先被吸附能高的化学吸附位点吸附,化学吸附饱和后,才会进行物理吸附。     

红外光谱研究Fenton试剂对多壁碳纳米管表面的影响

碳纳米管经焙烧和稀硝酸纯化处理后,在不同实验条件下采用Fenton试剂对多壁碳纳米管进行化学改性,红外光谱(FTIR)结果表明,Fenton试剂化学处理后能够在碳纳米管表面引入羟基和羰基,且羰基峰的吸收强度随着反应时间的增加而增加;碳纳米管的化学处理条件即过氧化氢与亚铁离子物质的量之比、pH值和反应时间等因素能够影响碳纳米管的改性效果;过氧化氢与亚铁离子物质的量之比控制在10左右,pH保持在3,反应10h即能在碳纳米管表面产生较多的羰基.此外,根据Fenton试剂产生羟基自由基的机理和碳纳米管改性前后的FTIR变化,初步分析了Fenton试剂与碳纳米管作用的可能机理.机理分析表明,羟基和羰基的产生是由亲电性的HO·对碳纳米管上的不饱和键进行加成氧化引起的.     

功能化石墨烯改性聚乙烯热力学特性的分子动力学模拟

聚乙烯绝缘材料在我国高压电缆中有着广泛的应用.为了提高其耐热稳定性和力学性能,利用石墨烯对聚乙烯进行掺杂改性,并基于分子动力学模拟的研究方法分别建立了低密度聚乙烯(LDPE)、石墨烯和3种官能团接枝石墨烯掺杂聚乙烯的复合模型.研究表明,相比石墨烯直接掺杂聚乙烯,羧基(-COOH)、氨基(-NH)和羟基(-OH)接枝石墨烯能够更加有效地提高聚乙烯的玻璃化温度(分别提高了16 K、7 K、5 K),减弱聚乙烯分子链的移动和降低聚乙烯的热膨胀系数、均方位移(MSD),从而使得聚乙烯复合体系的热学性能得到了有效增强.此外发现石墨烯的掺杂能够提高复合模型的力学模量,其中官能团接枝石墨烯改进效果更明显,室温下弹性模量和剪切模量的提升幅度由不接枝的33.98%、36.18%,提升到了44%和42.89%(羧基功能化体系).研究结果可为聚乙烯绝缘材料的热老化抑制和力学性能的改善提供有益的参考.     

光谱法研究酵母菌对铜离子的吸附机理

采用AAS,FTIR,SEM/EDS等方法研究了啤酒酵母对铜离子的吸附作用。 酵母菌经丙酮和NaOH处理后对Cu2+的吸附量明显增加,而将羧基酯化和将氨基甲基化使得酵母菌对Cu2+的吸附能力显著降低。化学修饰与酵母菌对Cu2+吸附的吸附结果表明,细胞壁上的羧基、氨基在酵母菌吸附铜时起着重要的作用。 红外光谱表明,酵母菌表面有结合金属的官能团,如羟基、羧基、氨基等,吸附Cu2+后,3 392 cm-1处的吸收峰紫移至3 404,1 405 cm-1处的峰红移到1 383 cm-1,细胞的主要成分和结构保持完整。 SEM/EDS分析表明,吸附后酵母菌表面变化不大,酵母菌仅结合少量Cu2+。     

燃料电池阴极扩散层扩散特性研究

本文采用粗粒化分子动力学方法研究了燃料电池阴极扩散层的扩散特性。采用全原子方法的计算结果校验了粗粒化方法的准确性,并提出了一种定量校正方案。分析了碳纳米管气体扩散层中气体和水的扩散特性,其中气体和水的扩散存在各向异性,气体和水两者在碳纳米管中轴向的扩散系数均较低,且气体和水的轴向扩散系数也随着该分子比例的降低而进一步降低;对带缺陷气体扩散层的研究表明气体扩散层中缺陷的形态对其扩散性能有显著的影响。     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Multi-pulse operation of a Kerr-lens mode-locked femtosecond laser

Our experimental results show that the presence of a proper amount of negative group velocity dispersion is essential to multi-pulse operation of a Kerr-lens mode-locked femtosecond laser. We demonstrate that the pulse separations and the number of pulses contained within a cavity round trip are strongly dependent on the initial perturbations. The results allow us to get a better understanding on the influences of the convoluted self-phase modulation and intra-cavity dispersions on the stable multi-pulse oscillation in a Kerr-lens mode-locked femtosecond laser.     

Propagation of Helmholtz-Gauss beams in weak turbulent atmosphere

Based on the Rytov approximation of light propagation in weak turbulent atmosphere,the closed-form expressions of field and average irradiance of each one of the four fundamental families of Helmholtz-Gauss (HzG)beams:cosine-Gauss beams,stationary Mathieu-Gauss beams,stationary parabolic-Gauss beams,and Bessel-Gauss beams,which are propagating in weak turbulent atmosphere,are obtained.The results show that the field and average irradiance can be written as the product of four factors:complex amplitude depending on the z-coordinate only,a Ganssian beam.a factor of complex phase perturbation induced by atmospheric turbulence,and a complex scaled version of the transverse shape of the non-diffracting beam.The effect of weak atmospheric turbulence on irradiance distribution of the HzG beam can be ignored.     

An effective method for reducing speckle noise in digital holography

An effective method for reducing the speckle noise in digital holography is proposed in this paper.Different from the methods based on classical filtering technique,it utilizes the multiple holograms which are generated by rotating the illuminating light continuously.The intensity images reconstructed by a series of holograms generated by rotating the illuminating light possess different speckle patterns.Hence by properly averaging the reconstructed intensity fields,the speckle noises can be reduced greatly.Experimental results show that the proposed method is simple and effective to reduce speckle noise in digital holography.     

Influence of purity of HfO2 on reflectance of ultraviolet multilayer

The impurities in two kinds of HfO2 materials and in their corresponding single layer thin films were determined through glow discharge mass spectrum technology and secondary ion mass spectrometry(SIMS) equipment respectively.It was found that ZrO2 was the main impurity in the two kinds of HfO2 either in the original HfO2 materials or in the electron beam deposited films.In addition,the difference of Zr content in the two kinds of HfO2 single laver films was much laxger than that of the other impurities such as Ti and Fe.which showed that it was just ZrO2 that made the difference between the optical performance of the film products including the two kinds of HfO2.With these two kinds of HfO2 and the same kind of SiO2.we deposited HfO2/SiO2 multilayer reflective coatings at the wavelength of 266 nm.Experimental results showed that the reflectances of these two mirrors were about 99.85% and 99.15% respectively,which agreed well with the designed results what were based on the optical constants obtained from the corresponding single layer thin films.     

Speech enhancement by array crosstalk resistant ANC and spectrum subtraction

Microphone array-based speech enhancement has great importance for speech communications and speech recognition. To reduce the aperture of the microphone array and to increase the effect of the speech enhancement will greatly broaden the application areas of the microphone array. An array crosstalk resistant adaptive noise cancellation method is therefore presented. And then an improved spectral subtraction algorithm is further cascaded to obtain better enhancement results. Theoretic analysis and experiments indicate that the proposed scheme needs only a very small microphone array while it simultaneously achieves a higher SNR improvement. Besides, the proposed scheme can be used in many noisy environments and is easy for real-time implementation.