基于二维多模干涉效应的N×N光开关模型

报道了由两个N×N三维多模干涉耦合器和一段阵列相移波导组成的三维光开关.首先利用导模传输法分析了三维多模干涉耦合器的一般成像原理,并推导出了其成像位置以及相位矩阵.在此基础上,通过场传输矩阵法建立了光开关的传输方程.利用该传输方程计算得到了光开关工作时,阵列相移波导的相位条件,并通过三维有限差分光束传输法进行仿真验证,...     

多模干涉马赫曾德尔光开关模型

根据N×N多模干涉耦合器的基本原理 ,确定了多模干涉耦合器的结构参数。通过分析多模干涉耦合器的输入光场与其映像间的相位关系 ,提出了模传输矩阵的分析方法 ,并用此方法分析了N×N普通干涉多模干涉耦合器、N×N相移器以及N×N普通干涉多模干涉马赫 曾德尔光开关 ,得到了它们的模场传输方程 ,分析了光开关在光场从任一输入端输入 ,从任一输出端输出时开关的驱动条件。用上面的方法分析了 4× 4光开关的结构及驱动条件     

采用三维波束传输法的多模干涉耦合器成像位置的数值计算

多模干涉(MMI)耦合器需要精确定位成像位置,以便器件的设计制作。针对强限制和弱限制的三维多模波导干涉耦合器,采用三维交替方向隐式有限差分光束传输法(BPM),数值计算得出多模波导长度、输入波导和输出波导位置。首先通过对对称干涉多模干涉耦合器的数值分析求得多模干涉耦合器的等效宽度Weq及最低二阶模之间的拍长Lc,然后将这些参量结合光束传输法直接用于器件设计。计算显示该方法得到的成像位置和导模传输分析法(MPA)的理论预测比较接近,但Weq和Lc却是由光束传输法计算得到的,导模传输分析法理论只能在得到Weq和Lc的前提下才能得到成像位置。该方法直接针对三维波导进行,没有采用基于等效折射率方法的从三维波导到二维波导的简化处理,并且也没有采用导模传输分析法所采用的近似,保证了计算精度,对于实际多模干涉器件的设计制作可起参考作用。     

N × N集成光开关阵列模型

报道了由2N个1 × N 多模干涉马赫-曾德尔光开关组成的N × N光开关阵列结构,分析了这种结构的开关阵列优势和局限性.用场传输矩阵方法建立了1 × N多模干涉光开关的光场传输方程.给出了光开关阵列从任一输入端输入、从任一输出端输出时阵列开关的工作条件.在上述原理及理论基础上分析了4×4光开关阵列的结构和工作条件.     

基于多模干涉耦合器的阵列波导光栅设计研究

研究了基于多模干涉(MMI)耦合器的阵列波导光栅(AWG).通过模式传输分析方法,分析了多模干涉耦合器及阵列波导;并给出在硅基底上的二氧化硅波导上四通道100 GHz-AWG普通结构和紧凑结构的设计结果.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550 nm波长附近的40 nm带宽范围内获得了约2.6 dB的通带平坦度,在1 550 nm通信波长处,器件的插入损耗低于10 dB.     

一种改进的2×2 SOI Mach-Zehnder热光开关

本文设计并制作了基于强限制多模干涉耦合器的2×2 SOI马赫-曾德热光开关.这种光开关采用了深刻蚀结构的多模干涉耦合器和输入/输出波导,较大地提高了干涉耦合器的性能并减少了连接耦合损耗.同时,在调制臂区域采用浅刻蚀结构,保持其单模调制状态.深刻蚀多模干涉耦合器具有优越的特性,在实验中测得不均衡度只有0.03 dB,插入损耗－0.6 dB.基于这种耦合器的新型热光开关,其插入损耗为－6.8 dB,其中包括光纤-波导耦合损耗－4.3 dB,开关时间为6.8 μs.     

InP基1×4多模干涉耦合器的设计与制作

在密集波分复用系统中,多波长DFB激光器阵列与多模干涉耦合器集成光源器件具有重要的应用前景.为了研制多波长集成光源中的宽带可用低损耗光耦合器,利用三维有限差分光束传播法仿真设计了一种具有强限制作用的InP/InGaAsP材料的多模干涉型耦合器.输入/输出端波导均采用楔形结构以降低多模干涉型耦合器的插入损耗,提高各个输出端口的出光平衡度.根据仿真结果,结合波导芯层为采用外延生长设备,采用反应离子刻蚀工艺制作了1×乘4多模干涉型耦合器.利用自动对准波导耦合测试系统对所制作器件的插入损耗和出光平衡度进行测量.测试结果表明,该器件在1 550nm波长附近的40nm带宽范围内获得了约2.6dB的通带平坦度,在1 550nm通信波长处,器件的插入损耗低于10dB.     

锥形多模干涉耦合器一般成像特性分析

锥形多模干涉耦合器克服了传统多模干涉(MMI)耦合器结构尺寸大的缺点,满足当前集成光器件高集成度的要求.其成像特性对设计基于它的集成光器件至关重要.根据多模干涉耦合器的自映像原理,对锥形多模干涉耦合器成像特性进行分析,发现成像特性与输入场位置、位置数、多模波导初始宽度及渐变率等参量密切相关,得到成像位置的解析表达式并总...     

多模干涉耦合器一般成像位置分析

自映像效应是多模波导的一个重要特性,利用多模波导自映像效应制成的多模干涉耦合器被广泛地应用于集成光学回路中。然而根据以往的文献要得出多模干涉耦合器的成像位置要经过一系列复杂的计算。根据多模干涉耦合器的自映像原理,对多模干涉耦合器的成像位置进行分析。成像位置与输入场位置和位置数密切相关,给出了成像位置的解析表达式,得出奇数、偶数的位置数的成像位置分别对应相同,并且奇、偶数的位置数所对应的成像位置之和为多模波导宽度的成像规律。用导模传输分析法验证了表达式和成像规律的正确性。根据成像位置的表达式和成像规律可以直接得出任意输入场位置和位置数所对应的成像位置。为一维和二维限制的多模干涉耦合器的设计提供了理论基础。     

数值模拟二维间隙表面等离子波导传输特性

利用表面等离子激元的新颖特性,设计了二维间隙表面等离子波导.以这种结构为基础通过变形和组合形成90°直角弯曲波导、T型光功率分配器和光开光,采用时域有限差分法研究了它们的传输特性.结果表明:不同于介质光波导的弯曲损耗来自于辐射泄漏,90°直角弯曲间隙表面等离子波导的能量损耗主要来自于金属中的欧姆热损耗.在间隙达到40 nm以上后,当直行段的长度适当时,弯曲段的透射率较相同长度的直波导的透射率要大.T型光功率分配器在两输出波导的间隙宽度比达到0.6及以上时,不同于传统介质波导的分光原则,能量主要沿等效折射率较小的输出臂流出.当两输入光的相位反相时,T型光开关处于输出截止的状态,当两输入光的相位同相时,T型光开关处于输出导通的状态.所有波导间隙均小于衍射极限,实现了超衍射极限传播,可用于未来了超大规模集成光路中.     

Optical switch effect of metal–dielectric–metal plasmonic waveguide coupled with stub structure

The transmission line theory (TLT) and the finite difference time domain (FDTD) method are applied to investigate the optical transmission characteristics of the metal–dielectric–metal (MDM) plasmonic waveguide coupled with a stub structure. The transmission rate of the FDTD simulation results demonstrates periodically variation from less than 1% to more than 92% as a function of the length of the stub, which fits well with the results of TLT. Furthermore, the transmission also performs a periodically switch distribution with the change of the refractive index of the stub from 1.0 to 2.0 gradually. Both methods are adopted for modulating the superposition phase of the interference between the reflected surface plasmon polaritons (SPPs) wave from the end of the stub and the passing SPPs wave in the waveguide, which can be interpreted as the principle mechanism for the optical switch effect of the MDM waveguide with a stub structure.     

A polymeric optical switch array based on arrayed waveguide grating structure

A novel 1 × N optical switch array based on arrayed waveguide grating (AWG) structure is presented in this paper. The device is designed for polymeric materials with a large negative thermooptic (TO) coefficient, which is employed to change the imaging effect and to realize optical switching. When input wavelength is located in a special waveband, the optical signal will image at different output channel as temperature changes. The two-dimensional finite difference beam propagation method (FD-BPM) has been used to simulate a 1 × 9 optical switch array. The insertion loss of this switch array is below 1.37 dB and the extinction ratio is better than 31 dB at 1550 nm, when the coupling and propagation loss is neglected. The optimum design and the simulation results show that this structure could be a multiple wavelengths switching at the same time.     

Theoretical Design of a Pump‐Free Ultrahigh Efficiency All‐Optical Switching Based on a Defect Ring Optical Waveguide Network

A theoretical design of a defect ring optical waveguide network is proposed to construct a pump‐free ultrahigh efficiency all‐optical switch. This switch creates ultrastrong photonic localization and causes the nonlinear dielectric in the defect waveguide to intensely respond. At its ON state, this material defect without Kerr response helps to produce a pair of sharp pass bands in the transmission spectrum to form the dual channel of the all‐optical switch. When it is switched to its OFF state, the strong Kerr response induced refractive index change in the high nonlinear defect waveguide strongly alters the spectrum, leading to a collapse of the dual channels. Network equation and generalized eigenfunction method are used to numerically calculate the optical properties of the switch and obtain a threshold control energy of about 2.90 zJ, which is eight orders of magnitude lower than previously reported. The switching efficiency/transmission ratio exceeds 3× 10¹¹, which is six orders of magnitude larger than previously reported. The state transition time is nearly 108 fs, which is approximately two orders of magnitude faster than the previously reported shortest time. Furthermore, the switch size can be much smaller than 2.6 µm and will be suitable for integration.     

Phase-shift interferometry measured transmission matrix of turbid medium: Three-step phase-shifting interference better than four-step one

Transmission matrix(TM) is an important tool for controlling light focusing, imaging, and communication through turbid media. It can be measured by 3-step(TM3) or 4-step(TM4) phase-shifting interference, but the similarities and differences of the transmission matrices obtained by the two methods are rarely reported. Therefore, we make a quantitative comparison of the peak light intensity, signal-to-noise ratio, and average background of 24 × 24 = 576 focal points between paired samples(TM3–TM4) through the Wilcoxon rank sum test, and discuss the singular value of the transmission matrix and the focal peak. The comparative results of peak light intensity and signal-to-noise ratio show that there is a significant difference between the 3-step phase shift and the 4-step phase shift transmission matrixes. The focusing effect of the former is significantly better than that of the latter; interest concentrates on the focal intensity and singular value. The reciprocal of the singular value is proportional to the squared intensity, which is in accordance with singular value theory. The results of comparison of peak light intensity and signal-to-noise ratio strongly suggest that 3-step phase shift should be selected and used in applying the phase shift method to the measurement of the transmission matrix; and the singular value is of great significance in quantifying the focusing, imaging, and communication quality of the transmission matrix.     

Coherent interference induced transparency in self-coupled optical waveguide-based resonators

We propose a self-coupled optical waveguide (SCOW)-based resonator to generate an optical resonance analogous to electromagnetically induced transparency (EIT). The EIT-like effect is formed by the coherent interference between two resonance paths inherent to the SCOW resonator. For cascaded SCOW resonators, the spectrum they produce is significantly affected by the phase shift between them, with the EIT-like peak flattened or split as the two extreme cases. We also investigate the dispersion characteristics of an infinite array of SCOW resonators and show that the dispersion relation and group index in the EIT subband can be greatly changed by a small phase shift between the SCOW resonators.     

SOI波导反射模式的古斯-汉欣空间位移效应及其数字式热光开关

借助波导转角镜结构,利用古斯-汉欣空间位移和热光效应折射率调制的有效组合,提出了波导反射模式数字式热光开关结构。在给定入射角的条件下优化了空间古斯-汉欣位移,在具有古斯-汉欣效应的本征态下,反射光束出现了较大的跳跃。在1.0μm厚硅膜的绝缘体上硅平台上,单模输入波导和多模干涉波导结构之间的导模本征态匹配,验证了1×3数字式光开关功能。实验中,器件结构引起的光损耗为0.3 dB,开关功率为130~150 mW,开关时间约为50μs,相邻输出端之间隔离度为15 dB。与马赫-曾德尔干涉仪型的2×2热光开关和等离子体效应热光开关的最新结果进行比较证明了该数字式热光开关的先进性。     

Design analysis of all-optical devices using second harmonic generation into a region with periodically modulated optical property

We investigate the nonlinear optical interaction through a periodic waveguide structure consisting of two alternating segments with different linear and nonlinear optical properties. A coupled equation system has been used to calculate the intensity of fundamental and second harmonic waves and the phase shift of the fundamental. The model has been experimentally tested with good results, but the effect of the phase shift has not been considered. Comparison with the quasi-phase match (QPM) technique has been presented. The novel features introduced by alternating segments with different linear and nonlinear optical properties have been discussed. The model shows a more flexible approach, which can be used in designing optical components based on coherent nonlinear interaction. Applications are straightforward for frequency doubler and all-optical switch.