Structure and mechanical properties of titanium nitride/carbon nitride multilayers

The structure and mechanical properties of the multilayers consisting of 5-73 nm thick titanium nitride (TiN) and 4.6 nm thick carbon nitride (CN) have been investigated. It has been found that the CN layers are amorphous and the TiN layers thinner than 17 nm are amorphous. The TiN layers become crystallized as the thickness is increased to 30 nm or thicker. The hardness from the composite response of the multilayered films and their substrates determined using continuous stiff measurement is smaller than the film-only hardness (without substrate effects) calculated using Bhattacharya-Nix empirical equation. The hardness increases with raising the thickness of TiN layers. With the crystallization of the TiN layer, the multilayers become even harder than that calculated based on the rule of mixtures. However, no enhancement in hardness has been observed when the TiN layers are amorphous.     

TiN/Al2O3纳米多层膜的共格外延生长及超硬效应

采用多靶磁控溅射法制备了一系列具有不同Al₂O₃调制层厚度的TiN/Al₂O₃纳米多层膜. 利用X射线能量色散谱、X射线衍射、扫描电子显微镜、高分辨透射电子显微镜和微力学探针表征了多层膜的成分、微结构和力学性能. 研究结果表明，在TiN/Al₂O₃纳米多层膜中，单层膜时以非晶态存在的Al₂O₃层在厚度小于1.5 nm时因TiN晶体层的模板效应而晶化，并与TiN层形成共格外延生长，相应地，多层膜产生硬度明显升高的超硬效应，最高硬度可达37.9 GPa. 进一步增加多层膜中Al₂O₃调制层的层厚度，Al₂O₃层逐渐形成非晶结构并破坏了多层膜的共格外延生长，使得多层膜的硬度逐步降低. 关键词： 2O₃纳米多层膜')" href="#">TiN/Al₂O₃纳米多层膜 外延生长 非晶晶化 超硬效应     

TiN/SiC纳米多层膜的生长结构与力学性能

研究了TiN/SiC纳米多层膜中立方SiC（B1cubic SiC）的形成及其对TiN/SiC多层膜力学性能的影响.结果表明：在TiN/SiC多层膜中，非晶态的SiC层在厚度小于0.6nm时形成立方结构并与TiN形成共格外延生长的超晶格柱状晶，使多层膜产生硬度和弹性模量显著升高的超硬效应，最高硬度超过60GPa.SiC随着层厚的增加转变为非晶相，从而阻止了多层膜的共格外延生长，使薄膜呈现TiN纳米晶和SiC非晶组成的层状结构特征，同时多层膜的硬度和弹性模量下降.TiN/SiC纳米多层膜产生的超硬效应与立方 关键词： 立方碳化硅 TiN/SiC纳米多层膜 外延生长 超硬效应     

Investigation on microstructure and properties of CrAlN/AlON nanomultilayers

Artificially modulated CrAlN/AlON nanomultilayers were synthesized by direct current reactive magnetron sputtering. The microstructure and mechanical properties were evaluated by X-ray diffraction (XRD), high-resolution transmission electron microscopy (HRTEM) and nano-indentation techniques. The crystallization of AlON layer and its influence on the mechanical property of the nanomultilayers were studied. The results revealed that, under the template effect of NaCl structural CrAlN layer, amorphous AlON was forced to crystallize and grew epitaxially with CrAlN layer when AlON layer thickness was below 0.9 nm, leading to an increase of hardness up to 32.8 GPa. With the further increase of the AlON layer thickness, AlON layer gradually transformed into amorphous structure and blocked epitaxial growth of the multilayers, resulting in the decrease of hardness. The effect of CrAlN layer thickness on hardness of CrAlN/AlON nanomultilayers was also investigated. With the decrease of CrAlN layer thickness, the hardness increased gradually. The maximum hardness was 34.7 GPa when CrAlN layer thickness of was 3.0 nm. The strengthen mechanism of CrAlN/AlON nanomultilayers was finally discussed.     

Thickness dependence of electrical properties of ITO film deposited on a plastic substrate by RF magnetron sputtering

Indium tin oxide (ITO) films with various thicknesses in range of 40-280 nm were prepared onto a plastic substrate (PMMA). Deposition was carried out with RF magnetron sputtering method and the substrate temperature was held at ∼70 °C, in lack of the thermal damage to the polymer substrate. Changes in microstructure and electrical properties of ITO films according to their thicknesses were investigated. It was found that amorphous layer with thickness of 80 nm was formed at the interface on the polymer substrate and polycrystalline ITO could be obtained above the thickness. Conductivity of ITO films was found to be strongly dependent on the crystallinity. Consequently, it is suggested that crystallinity of the deposited films should be enhanced at the initial stage of deposition and the thickness of amorphous region be reduced in order to prepare high quality ITO thin films on polymer substrates.     

TiN/SiO2纳米多层膜的晶体生长与超硬效应

高硬度的含氧化物纳米多层膜在工具涂层上具有重要的应用价值.研究了TiN/SiO2_{2纳米多 层膜的晶体生长特征和超硬效应.一系列具有不同SiO22和TiN调制层厚的纳米多 层膜采用多 靶磁控溅射法制备；采用x射线衍射、x射线能量色散谱、高分辨电子显微镜和微力学探针表 征了多层膜的微结构和力学性能.结果表明，虽然以单层膜形式存在的TiN和SiO22分别形成 纳米晶和非晶结构，它们组成多层膜时会因晶体生长的互促效应而呈现共格外延生长的结构 特 关键词： 2纳米多层膜')" href="#">TiN/SiO22纳米多层膜 外延生长 非晶晶化 超硬效应}     

Crystallization kinetics of amorphous SiC films: Influence of substrate

The crystallization kinetics of amorphous silicon carbide films was studied by means of X-ray diffractometry (XRD) and transmission electron microscopy (TEM). The films were deposited by radio frequency (r.f.) magnetron sputtering on glassy carbon and single crystalline silicon substrates, respectively. TEM micrographs and XRD patterns show the formation of nano-crystalline β-SiC with crystallite sizes in the order of 50 nm during annealing at temperatures between 1200 and 1600 °C. A modified Johnson-Mehl-Avrami-Kolmogorov (JMAK) formalism was used to describe the isothermal transformation of amorphous SiC into β-SiC as an interface controlled, three-dimensional growth processes from pre-existing small crystallites in the order of 10 nm. These pre-existing crystallites are formed in a transient process in the early stages of crystallization. For films deposited on the silicon substrate, the obtained rate constants of crystallite growth obey an Arrhenius behavior with an activation enthalpy of 4.1 ± 0.5 eV in accordance with literature data. Films deposited on glassy carbon show an increased stability of amorphous SiC films, which is reflected in smaller rate constants of crystallite growth of several orders of magnitude at low temperatures and a higher activation enthalpy of 8.9 ± 0.9 eV. A model is proposed, where the faster crystallization of films on silicon substrates can be explained with the presence of superabundant point defects, which diffuse from the substrate into the film and accelerate the incorporation of atoms from the amorphous into the crystalline phase.     

Structural and optical properties of thin films porous amorphous silicon carbide formed by Ag-assisted photochemical etching

In this work, we present the formation of porous layers on hydrogenated amorphous SiC (a-SiC: H) by Ag-assisted photochemical etching using HF/K₂S₂O₈ solution under UV illumination at 254 nm wavelength. The amorphous films a-SiC: H were elaborated by d.c. magnetron sputtering using a hot pressed polycrystalline 6H-SiC target. Because of the high resistivity of the SiC layer, around 1.6 MΩ cm and in order to facilitate the chemical etching, a thin metallic film of high purity silver (Ag) has been deposited under vacuum onto the thin a-SiC: H layer. The etched surface was characterized by scanning electron microscopy, secondary ion mass spectroscopy, infrared spectroscopy and photoluminescence. The results show that the morphology of etched a-SiC: H surface evolves with etching time. For an etching time of 20 min the surface presents a hemispherical crater, indicating that the porous SiC layer is perforated. Photoluminescence characterization of etched a-SiC: H samples for 20 min shows a high and an intense blue PL, whereas it has been shown that the PL decreases for higher etching time. Finally, a dissolution mechanism of the silicon carbide in 1HF/1K₂S₂O₈ solution has been proposed.     

Initial study on the structure and photoluminescence properties of SiC films doped with Al

SiC films doped with aluminum (Al) were prepared by the rf-magnetron sputtering technique on p-Si substrates with a composite target of a single crystalline SiC containing several Al pieces on the surface. The as-deposited films were annealed in the temperature range of 400-800 °C under nitrogen ambient. The thin films have been characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The results show that the introduction of Al into films hinders crystalline formation process. And with the increase of annealing temperature, more Si particles are formed in the films, which strongly affect the optical absorption properties. The photoluminescence (PL) spectra of the samples show two peaks at 370 nm and 412 nm. The intensities of the PL peaks are evidently improved after Al doped. We attribute the origin of the two PL peaks to a kind of Si-related defect centres. The obtained results are expected to have important applications in modern optoelectronic devices.     

AlN/BN纳米结构多层膜微结构及力学性能

用射频磁控溅射法制备了AlN,BN单层膜及AlN/BN纳米多层膜.采用X射线衍射仪、高分辨率透射电子显微镜和纳米压痕仪对薄膜结构进行表征.分析表明：单层膜AlN为w-AlN结构,BN为非晶相.AlN/BN多层膜中BN的结构与BN层厚有关.当BN层厚小于0.55nm时,由于AlN层模板的作用,BN发生了外延生长,BN与AlN的结构相同;当BN层厚大于0.74nm时,BN为非晶.AlN/BN多层膜的硬度也与BN层的厚度有关.当BN层厚为1—2个分子层时,AlN/BN多层膜具有超硬效应;当BN层厚增加到0.74 关键词： AlN/BN多层膜 BN结构 超硬效应     

The structure and photoluminescence properties of Cr-doped SiC films

Cr-doped SiC films are prepared by the RF-magnetron sputtering technique on Si substrates with a composite target of a single-crystalline SiC containing several Cr pieces on the surface. The as-deposited films are annealed in the temperature of 1000 °C under nitrogen ambient. The structure of the samples has been characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and Raman scattering measurement. The results show that the SiC crystal is formed and that majority of Cr doped in the SiC resulted in the formation of the C clusters. Then the photoluminescence (PL) spectra of the samples are observed in the visible range at room temperature. The optical properties of the samples have also been discussed briefly. We attribute the origin of the 412-nm PL band to a kind of C cluster center.     

Preparation of dielectric mirrors from high-refractive index contrast amorphous chalcogenide films

We report the preparation of planar 15-layer dielectric mirrors by a thermal evaporation of alternating high refractive index contrast amorphous chalcogenide Sb-Se and Ge-S layers, exhibiting a high-reflection band around 1.55 μm. The layer deposition quality and the thickness accuracy of such prepared chalcogenide multilayers were then checked using transmission electron microscopy. The layer thickness deviation of chalcogenide layers did not exceed ∼7 nm in comparison with the desired thicknesses. The width of Sb-Se/Ge-S layer boundary was approximately ∼3 nm, which is in good agreement with the surface roughness values of thermally evaporated Sb-Se and Ge-S single layers. The optical properties of the prepared 15-layer dielectric mirrors were consistent in temperature range of 20-120 °C; however, at higher temperatures there started apparent structural changes of Sb-Se films, which were followed by their crystallization. Excellent optical properties of chalcogenide materials in the infrared range make them interesting for applications, e.g., in optics and photonics.     

反应磁控溅射ZrN/AlON纳米多层膜的晶体生长和超硬效应

采用Zr靶和Al₂O₃靶通过在Ar，N₂混合气氛中进行反应磁控溅射的方法制备了不同AlON调制层厚和不同ZrN调制层厚的两个系列的ZrN/AlON纳米多层膜.利用X射线能量色散谱仪、X射线衍射仪、高分辨透射电子显微镜和微力学探针研究了多层膜的成分、微结构和力学性能.结果表明，在Ar，N₂混合气氛中对Al₂O₃进行溅射的过程中，N原子会部分取代Al₂O₃中的氧原子，形成AlON化合物.在ZrN/AlON纳米多层膜中，由于受到ZrN晶体调制层的模板作用，溅射条件下以非晶态存在的AlON层在其厚度小于0.9nm时被强制晶化并与ZrN层形成共格外延生长；相应地，多层膜的硬度明显提高，最高硬度达到33.0GPa.进一步增加多层膜中AlON调制层的厚度，AlON层形成非晶结构，破坏了多层膜的共格外延生长，导致其硬度逐步降低. 关键词： ZrN/AlON纳米多层膜 外延生长 非晶晶化 力学性能     

Thickness dependence of structural, electrical and optical properties of indium tin oxide (ITO) films deposited on PET substrates

Without intentionally heating the substrates, indium tin oxide (ITO) thin films of thicknesses from 72 nm to 447 nm were prepared on polyethylene terephthalate (PET) substrates by DC reactively magnetron sputtering with pre-deposition substrate surfaces plasma cleaning. The dependence of structural, electrical, and optical properties on the films thickness were systematically investigated. It was found that the crystal grain size increases, while the transmittance, the resistivity, and the sheet resistance decreases as the film thickness was increasing. The thickest film (∼447 nm) was found of the lowest sheet resistance 12.6 Ω/square, and its average optical transmittance (400-800 nm) and the 550 nm transmittance was 85.2% and 90.4%, respectively. The results indicate clearly that dependence of the structural, electrical, and optical properties of the films on the film thickness reflected the improvement of the film crystallinity with the film thickness.     

Thickness-dependent magnetization reversal in CoZrNb amorphous films

Structure and magnetization of CoZrNb amorphous films prepared by DC magnetron sputtering have been studied as a function of film thickness (t), from 35 to 840 nm. Using comprehensive characterization, we show that the CoZrNb amorphous films possess a single phase and no nanocrystalline can be detected. The magnetic measurements indicate that the magnetization reversal of CoZrNb films is strongly dependent on t. That is, the coercivity is abruptly reduced to be lower than 4 Oe with t increasing from 35 to 105 nm, and then gradually decreases to ∼0.2 Oe as t increases. This coercivity transition versus t is accompanied by the strong magnetization reversal when t is larger than 105 nm. The results reveal that CoZrNb amorphous films with comparatively large film thickness (>100 nm) are suitable for sensors and anti-faked materials.     

SiO2的赝晶化及AlN/SiO2纳米多层膜的超硬效应

采用反应磁控溅射法制备了一系列不同SiO₂层厚度的AlN/SiO₂纳米多层膜，利用X射线衍射仪、高分辨透射电子显微镜和微力学探针表征了多层膜的微结构和力学性能，研究了SiO₂层在多层膜中的晶化现象及其对多层膜生长方式及力学性能的影响. 结果表明，由于受AlN六方晶体结构的模板作用，溅射条件下以非晶态存在的SiO₂层在其厚度小于0.6 nm时被强制晶化为与AlN相同的六方结构赝晶体并与AlN形成共格外延生长. 由于不同模量的两调制层存在晶格错配度，多层膜中产生了拉、压交变的应力场，使得多层膜产生硬度升高的超硬效应. SiO₂随层厚的进一步增加又转变为以非晶态生长，多层膜的外延生长结构受到破坏，其硬度也随之降低. 关键词： 2纳米多层膜')" href="#">AlN/SiO₂纳米多层膜 赝晶化 应力场 超硬效应     

Effects of the sputtering time of ZnO buffer layer on the quality of GaN thin films

ZnO thin films with different thickness (the sputtering time of ZnO buffer layers was 10 min, 15 min, 20 min, and 25 min, respectively) were first prepared on Si substrates using radio frequency magnetron sputtering system and then the samples were annealed at 900 °C in oxygen ambient. Subsequently, a GaN epilayer about 500 nm thick was deposited on ZnO buffer layer. The GaN/ZnO films were annealed in NH₃ ambient at 950 °C. X-ray diffraction (XRD), atom force microscopy (AFM), X-ray photoelectron spectroscopy (XPS) and photoluminescence (PL) were used to analyze the structure, morphology, composition and optical properties of GaN films. The results show that their properties are investigated particularly as a function of the sputtering time of ZnO layers. For the better growth of GaN films, the optimal sputtering time is 15 min.     

TiCN/TiNbCN multilayer coatings with enhanced mechanical properties

Enhancement of mechanical properties by using a TiCN/TiNbCN multilayered system with different bilayer periods (Λ) and bilayer numbers (n) via magnetron sputtering technique was studied in this work. The coatings were characterized in terms of structural, chemical, morphological and mechanical properties by X-ray diffraction (XRD), atomic force microscopy (AFM), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and nanoindentation. Results of the X-ray analysis showed reflections associated to FCC (1 1 1) crystal structure for TiCN/TiNbCN films. AFM analysis revealed a reduction of grain size and roughness when the bilayer number is increased and the bilayer period is decreased. Finally, enhancement of mechanical properties was determined via nanoindentation measurements. The best behavior was obtained when the bilayer period (Λ) was 15 nm (n = 200), yielding the highest hardness (42 GPa) and elastic modulus (408 GPa). The values for the hardness and elastic modulus are 1.6 and 1.3 times greater than the coating with n = 1, respectively. The enhancement effects in multilayer coatings could be attributed to different mechanisms for layer formation with nanometric thickness due to the Hall-Petch effect; because this effect, originally used to explain the increase in hardness with decreasing grain size in bulk polycrystalline metals, has also been used to explain hardness enhancements in multilayers taking into account the thickness reduction at individual single layers that make the multilayered system. The Hall-Petch model based on dislocation motion within layers and across layer interfaces, has been successfully applied to multilayers to explain this hardness enhancement.     

AlN/Si3N4纳米多层膜的外延生长与力学性能

采用射频磁控溅射方法制备单层AlN, Si₃N₄薄膜和不同调制周期的AlN/Si₃N₄纳米多层膜.采用X射线衍射仪、高分辨透射电子显微镜和纳米压痕仪对薄膜进行表征.结果发现,多层膜中Si₃N₄层的晶体结构和多层膜的硬度依赖于Si₃N₄层的厚度.当AlN层厚度为4.0nm、 Si₃N₄层厚度 关键词： 3N₄纳米多层膜')" href="#">AlN/Si₃N₄纳米多层膜 外延生长 应力场 超硬效应     

TiN/TiB2异结构纳米多层膜的共格生长与力学性能

采用多靶磁控溅射法制备了一系列具有不同TiB₂调制层厚度的TiN/TiB_{2纳米多层膜.利用x射线衍射仪、高分辨电子显微镜和微力学探针研究了TiB2层厚变化对多层膜生长结构和力学性能的影响.结果表明，在fcc-TiN层(111)生长面的模板 作用下，原为非晶态的TiB2层在厚度小于2.9nm时形成hcp晶体态，并与fcc-TiN 形成共格外延生长；其界面共格关系为{111}TiN//{0001}TiB2，〈110〉TiN//〈1120〉TiB2.由于共格界面存在晶格失配 度，多层膜中形成拉、压交变的应力场，导致多层膜产生硬度和弹性模量升高的超硬效应， 最高硬度和弹性模量分别达到46.9GPa和465GPa.继续增加TiB2层的厚度，TiB2形成非晶态并破坏了与TiN层的共格外延生长，多层膜形成非晶TiN层和非晶TiB< sub>2层交替的调制结构，其硬度和弹性模量相应降低. 关键词： 2}纳米多层膜')" href="#">TiN/TiB₂纳米多层膜 共格生长 晶体化 力学性能