Gyrotron travelling wave amplifier: III. A proposed wide-band fast wave amplifier

A simple scheme is proposed for the construction of a wide-band fast wave gyrotron travelling wave amplifier. The key features of this scheme include a contoured waveguide, a tapered magnetic field, and injection of input signals in opposite direction of the streaming electrons. Bandwidths at tens of percents, and gain at tens of decibals, are projected.     

飞秒泵浦不同锥长微结构光纤超连续谱的产生

对飞秒脉冲泵浦下,不同锥长及锥腰直径的微结构光纤的超连续谱产生进行了实验研究。采用“快速低温拉锥方法”,在保持d/Λ不变的情况下,对实验室自制的空气孔间距Λ=6.53 μm,归一化孔径d/Λ=0.79的微结构光纤进行了拉锥,分别得到6,8,10 mm等不同锥长微结构光纤。理论计算表明,随着锥长变长,锥腰直径变小,锥腰处零色散波长向短波移动：未拉锥及6,8和10 mm锥微结构光纤锥腰处零色散波长分别为1 129,885,806和637 nm。利用中心波长为810 nm,重复频率76 MHz,脉宽120 fs的钛蓝宝石飞秒激光器对拉锥后微结构光纤进行了实验研究：锥长为6 mm时,泵浦光中心波长位于整根光纤的正常色散区,锥腰的零色散点附近,内脉冲拉曼散射和级联四波混频是光谱初始展宽的主要因素。泵浦功率达到450 mW时,在可见波段390～461 nm及红外波段1 134～1 512 nm形成-5 dB的平坦宽带连续光谱。泵浦功率达到500 mW时,出现366～2 450 nm覆盖紫外、可见、近红外、中红外的超连续谱,其光谱红蓝移边缘已经接近实验用微结构光纤的传输带宽。锥长为8 mm、泵浦功率为450 mW时,在群速度匹配和群加速度失配的共同影响下,连续谱蓝移边缘达到366 nm,比6 mm锥时蓝移9 nm;锥长为10 mm时,由于锥腰处零色散点移动到可见光区域,可见区光谱仍能满足相位匹配条件。通过级联四波混频效应,在可见区域实现了频率上转换及光谱蓝移。泵浦光功率达到500 mW时,在382～412 nm得到谱宽仅为30 nm,转换效率达到27.7%的频率上转换。     

直锥形光纤传输性质的研究

光纤通信的发展日新月异,光纤在信息的传输方面起着越来越重要的作用.通过把传输光纤的一端拉制成锥形,研究了光信号在锥形光纤中的传播行为.根据标量波动方程,运用高斯近似法,从理论上说明了光信号在锥形光纤中的传输特性和能量损耗,分析了光功率在光纤中的分布、光纤中基模场的模半径与光纤芯径的关系、光纤中光的传输模式与光纤芯径的关系、锥形光纤的传输效率与锥形光纤尖端直径的关系等.在实验上,用剪断法测量了锥形光纤的传输效率随锥形光纤圆锥角的变化关系.通过选取一系列锥角的大小,测出相应的传输效率,作出?湫是?并用具体数据进行半定量计算,得出锥形光纤顶端锥体的角度及其变化愈大愈光滑,锥形过渡区越短,传输效率就越高的结论.     

Polarization of Tapered Semiconductor Travelling-Wave Amplifiers

1　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｔａｐｅｒｅｄｓｅｍｉｃｏｎｄｕｃｔｏｒｔｒａｖｅｌｌｉｎｇ ｗａｖｅａｍｐｌｉｆｉｅｒｓｎｏｗａｒｅｏｎｅｏｆｔｈｅｉｍｐｏｒｔａｎｔｒｅｓｅａｒｃｈｓｕｂｊｅｃｔｓｉｎｓｅｍｉｃｏｎｄｕｃｔｏｒｏｐｔｏ ｅｌｅｃｔｒｏｎｉｃｓ.Ｂａｓｅｄｏｎｔｈｅｓｅｒｅｓｅａｒｃｈｒｅｓｕｌｔｓ,ｔｈｅｃｏｕｐｌｉｎｇｅｆｆｉｃｉｅｎｃｙｂｅｔｗｅｅｎｆｉｂｅｒａｎｄｓｅｍｉｃｏｎｄｕｃｔｏｒａｍｐｌｉｆｉｅｒ,ｔｈｅｌｉｆｅｔｉｍｅｏｆｄｅｖｉｃｅｓａｎｄｔｈｅ ｐｅｒｆｏｒｍ…     

Multipacting simulation and analysis of a taper quarter wave cavity by using Analyst-PT3P

Since the tapered quarter wave resonator (QWR) cavity is proven to have a much lower peak surface magnetic field in the short plate and a lower peak surface electric field near the beam tube compared with the straight outer conductor QWR, it has been recommended for the separated sector cyclotron linac injector system in the heavy ion research facility in Lanzhou. This paper is focused on the multipacting (MP) analysis for the tapered QWR with a frequency of 80.5 MHz and beta of 0.085. Using the Analyst program, MP bands can be simulated and analyzed with the Particle Tracking module to identify potential problems in the cavity design. This paper will present the simulation results of MP for the tapered QWR cavity.     

Characteristics of a tapered undulator for the X‐ray absorption fine‐structure technique at PLS‐II

An in‐vacuum undulator (IVU) with a tapered configuration was installed in the 8C nanoprobe/XAFS beamlime (BL8C) of the Pohang Light Source in Korea for hard X‐ray nanoprobe and X‐ray absorption fine‐structure (XAFS) experiments. It has been operated in planar mode for the nanoprobe experiments, while gap‐scan and tapered modes have been used alternatively for XAFS experiments. To examine the features of the BL8C IVU for XAFS experiments, spectral distributions were obtained theoretically and experimentally as functions of the gap and gap taper. Beam profiles at a cross section of the X‐ray beam were acquired using a slit to visualize the intensity distributions which depend on the gap, degree of tapering and harmonic energies. To demonstrate the effect of tapering around the lower limit of the third‐harmonic energy, V K‐edge XAFS spectra were obtained in each mode. Owing to the large X‐ray intensity variation around this energy, XAFS spectra of the planar and gap‐scan modes show considerable spectral distortions in comparison with the tapered mode. This indicates that the tapered mode, owing to the smooth X‐ray intensity profile at the expense of the highest and most stable intensity, can be an alternative for XAFS experiments where the gap‐scan mode gives a considerable intensity variation; it is also suitable for quick‐XAFS scanning.     

契形结构光纤表面等离子体共振传感器研究

提出了一种契形端面结构的光纤表面等离子体共振(SPR)传感器激励模型. 采用时域有限差分法对契形SPR波导的共振模型进行数值模拟, 通过在光纤出射端抛磨契形角度并进行敏感膜修饰, 制出具有契形端面结构的类Kretschmann微棱镜式光纤SPR传感器, 实现激发SPR的光波调制.结果表明, 在1.3330–1.4215折射率范围内, 制备的契形光纤SPR传感器相对于常规光纤SPR传感器, 其平均灵敏度提高了近1–6倍, 1倍和6倍分别出现在小角度结构(15° 契形) 传感器和大角度结构(60°契形) 传感器, 且仍保持 10^-5 等级的分辨率. 该类型结构的传感器具有契形端面激励模式, 设计灵活性高、制备工艺简单、可微量检测样本等优点, 能够很好地适应于不同环境和测量条件的实际生化检测、环境监测需求. 关键词： 光纤传感器 表面等离子体共振 契形端面结构 折射率灵敏度     

976 nm激光抽运二氧化硅微球级联拉曼散射激光的研究

利用电极放电产生的电弧高温熔融二氧化硅单锥细纤, 熔融的二氧化硅在表面张力作用下形成表面光滑的微球, 完成高品质因子微球腔的制备. 将976 nm激光通过锥光纤以倏逝场方式高效耦合入微球, 研究具有高能量密度回廊模的微球腔中的三阶非线性现象——受激拉曼散射现象. 在实验中测得了六级级联的拉曼散射激光, 各级拉曼散射激光分别测得单纵模或多纵模; 在抽运光功率不少于582.6 μW时, 测得位于1200 nm附近的拉曼散射激光; 当抽运光功率为3.014 mW时, 测得位于1287.04 nm附近的第六级拉曼散射激光. 关键词： 微球腔 锥光纤 高品质因子 拉曼散射激光     

Electromagnetic scattering from two-layer rough interfaces in the Kirchhoff approximation

Electromagnetic wave scattering from multilayers consisting of two two-layer Gaussian rough surfaces with lossless media is investigated in the Kirchhoff approximation (KA), with consideration of the shadowing effects. The tapered incident wave is introduced into the classic KA, and the bistatic scattering coefficient is redetermined. The advantage of this method is that it is faster in computation than the exact numerical methods. The numerical results show that the bistatic scattering coefficient calculated in the KA is in good agreement with that obtained by using the method of moment (MOM) over a most angular range, which indicates the validity of the KA proposed in our paper. Finally, the effects of the relative permittivity, the root-mean-square (RMS) height, the correlative length, and the average height between the two interfaces on the bistatic scattering coefficient are discussed in detail.     

Coupled-Soliton All-Optical Logic Device with Two Parallel Tapered Waveguides

In this article, a new all-optical logic device by using the interaction of spatial solitons has been proposed. The operation of the proposed device is based on the evolution of a nonlinear guided wave propagating along two parallel tapered waveguides with a Kerr-type nonlinear medium between them. The numerical results show that this device could be potentially useful in several all-optical logic functions (AND, OR, and XOR).     

Coupled-Soliton All-Optical Logic Device with Two Parallel Tapered Waveguides

In this article, a new all-optical logic device by using the interaction of spatial solitons has been proposed. The operation of the proposed device is based on the evolution of a nonlinear guided wave propagating along two parallel tapered waveguides with a Kerr-type nonlinear medium between them. The numerical results show that this device could be potentially useful in several all-optical logic functions (AND, OR, and XOR).     

微环芯腔与锥形纳米光纤耦合过程的实验研究

在实验上研究了共振于铯原子跃迁线附近的微环芯腔与锥形纳米光纤的耦合特性。通过精密控制微环芯腔与锥形纳米光纤的相对位置,实现了两者的欠耦合、临界耦合和过耦合的精确控制。当微环芯腔与锥形纳米光纤间距为0.6μm时,系统达到临界耦合,透射率为0.3%±0.3%,耦合效率为99.7%±0.3%。由微环芯腔透射光谱得到微环芯腔的自由光谱区为1067±5GHz,等效腔长为223±1μm,线宽为2.9±0.1GHz,本征品质因数为(6.2±0.6)×10~4。随着微环芯腔与锥形纳米光纤间距的减小,微环芯腔的线宽逐渐增大,共振频率发生红移,频率移动为19.2±0.1GHz。该研究找到了有效控制微环芯腔与锥形纳米光纤耦合状态的方法,为下一步实现微环芯腔与原子间强耦合奠定了实验基础。同时该研究加深了人们对微环芯腔不同耦合状态的认识,为研究欠耦合和过耦合状态提供了实验基础。     

锥形光纤的偏振特性

随着光通信技术的不断发展，光纤的应用越来越广泛，而锥形光纤以其独特的传光方式越来越多地应用于光纤连接、成像及测量等领域。实验测定了不同锥角和不同长度锥形光纤的偏振特性。理论上，根据麦克斯韦方程组以及边界条件给出了光在理想光纤中的场分布，阐明了实际光纤中光的传输特性。论证了锥形光纤长度与其偏振特性的关系，进而利用几何光学方法对锥形光纤锥角与其偏振特性的关系作了定性说明。并用具体数据进行了定量计算，得出偏振光经锥形光纤传输或耦合后再传输到其终端所得到均是椭圆偏振光的结论。     

利用锥型换能器的宽带低损耗声表面波滤波器设计

分析锥型换能器的基本原则是把换能器沿孔径方向划分成足够多的通道来进行近似,设计制作的关键是加权技术和数据处理技巧。由于SPUDT的特性,把EWC型的SPUDT引入到锥型换能器对制作宽带、低损耗器件是十分有用的;我们在Y128°LN基片上采用一般型和SPUDT型锥型换能器制作了相对带宽约15%的声表面波滤波器,一个换能器采用“块加权”,另一个换能器采用抽指加权。文中给出了两种器件的实验结果,SPUDT型声表面波滤波器的插损仅7.5dB。     

渐缩型锥形脉管制冷机的二维数值研究

本文开发了二维可压缩交变流动的SIMPLEC计算程序,对渐缩型锥形脉管制冷机进行了二维数值研究,研究了锥度对脉管制冷机性能的影响。数值计算结果表明,对渐缩型锥形脉管,存在一最佳锥度,此时的制冷效果最好,当锥度大于最佳锥度时,制冷效果反而变差。另外本文还从脉管内流场的分布及二次流的角度揭示了锥形脉管能提高制冷机性能的原因及内在机理。一定锥度下的锥形脉管不但可以改变脉管内二次流的大小,还改变了脉管内二次流的分布情况,使脉管冷热端的二次流分布变得不均匀。这是一定锥度下的锥形脉管可以改善脉管制冷机制冷效果的主要原因。     

脉动流血液通栓的晶格玻尔兹曼模型

本文把血浆看为水,红细胞当作密度为水的悬浮刚性小球,模拟脉动流在锥形管的中的通栓.首先在一定的压积和压差下,在锥形管中产生稳定的栓塞,然后用脉动流来通栓.改变脉动流的频率研究脉动流通栓的条件.     

渐变掩蔽图形超低压选择区域生长法制备高质量InGaAsP多量子阱材料

采用超低压(22 mbar)选择区域生长(Selective Area Growth, SAG)金属有机化学汽相沉积(Metal-organic Chemical Vapor Deposition, MOCVD)技术成功制备了高质量InGaAsP/InGaAsP多量子阱(Multiple Quantum Well, MQW)材料. 在较小的掩蔽宽度变化范围内(15—30μm)，得到了46nm的光荧光(Photoluminescence, PL)波长偏移量，PL半高宽(Full-Width-at-Half- 关键词： 超低压 选择区域生长 渐变掩蔽图形     

锥形光纤激发盘腔光学模式互易性研究

光学谐振腔由于其高Q值特性,作为谐振式陀螺的核心元件,有望实现谐振式陀螺的小型化、集成化,但是非互易性噪声成为制约其精度提高的不利因素. 介绍了采用传统半导体工艺制备的盘型腔与熔融法拉制的锥形光纤组成的耦合系统. 当盘型腔在光纤锥区的不同位置进行耦合谐振时,将输入输出正/反对调,观察到输出透射谱发生偏差,谐振频率、耦合效率以及Q值均发生变化,即存在非互易性现象. 用Rsoft软件对锥形光纤倏逝场分布特性进行仿真,理论分析了非互易性产生的原因. 以此可抑制谐振式光学陀螺应用中由锥形光纤与谐振腔组成的耦合系统产生的非互易性噪声. 关键词： 光学谐振腔 锥形光纤 非互易性 谐振式陀螺     

Study on pulse compression in tapered holey fibres

This paper proposes three kinds of tapered holey fibres with a multi-layer of holes whose pitch of air holes at the end of untapered and tapered are 5.8 μm and 1.8 μm. The central wavelength which locates in the anomalous dispersion region is 1.55 μm. An adaptive split-step Fourier method is numerically used to study the pulse propagation in tapered holey fibres. For the considered convex tapered holey fibre, at a wavelength of 1.55 μm, a compression factor of 136.7 can be achieved by initial width of 800 fs propagation through a length of 0.8 m. It demonstrates that in anomalous dispersion region, pulse can be compressed with the increase of nonlinearity coefficient and the decrease of dispersion coefficient.     

基于前后向迭代法的3维标量激光漫反射特性

 针对激光点对点通信方式的不足,提出了利用海面作为激光漫反射媒介进行组网通信的设想,并对激光入射理想导体表面后产生的散射场进行了的研究。首先利用3维标量锥形波对入射激光束进行了模拟;然后列出了积分方程,并根据矩量法进行了离散;最后通过前后向迭代法求解矩阵方程,得出了3维散射系数,准确地表示了基于理想导体界面的3维标量激光漫反射特性。