指数型功能梯度材料平面问题应力场通解

研究了功能梯度材料平面问题的应力场,引入Ariy应力函数,将问题转化为四阶偏微分方程,然后利用坐标变换方法,求得了应力函数的通解,进而得到了应力场的通解.     

条状功能梯度材料中偏心裂纹对反平面简谐波的散射问题

利用Schmidt方法研究了条状功能梯度材料中偏心裂纹对反平面简谐波的散射问题,裂纹垂直于条状功能梯度材料的边界．通过Fourier变换,问题可以转换为对一对未知变量是裂纹表面位移差的对偶积分方程求解．为了求解对偶积分方程,把裂纹表面的位移差展开为Jacobi多项式级数形式,进而得到了功能梯度参数、裂纹位置以及入射波频率对应力强度因子影响的规律．     

辛求解体系下功能梯度材料平面梁的完整解析解

采用辛弹性力学解法,求取弹性模量沿轴向指数变化,而Poisson比保持不变的功能梯度材料平面梁的完整解析解．通过求解被Saint-Venant原理覆盖的一般本征解,建立起完整的解析分析过程,进而给出平面梁位移和应力的精确分布规律．传统的弹性力学分析方法常常忽略被Saint-Venant原理覆盖的解,但这些衰减的本征解对材料的局部效应起着较大的影响作用,可能导致材料或结构的突然失效．采用辛求解方法,充分利用本征向量之间的辛共轭正交关系,得到了功能梯度材料梁的完整解析解．两个数值算例分别将功能梯度材料平面梁的位移和应力分布与相应均匀材料情形的结果进行比较,研究了材料非均匀性对位移和应力解的影响．     

梯度材料平板弯拉耦合力学的精确化支配方程

基于非均匀材料弹性力学理论,采用算子谱分解和算子代数方法,对梯度材料平板结构弯曲与拉伸问题进行了研究.首次给出了指数梯度材料平板弯曲与拉伸的力学方程.研究结果表明:与各向同性平板结构弯曲和拉伸问题不同,在功能梯度平板中描述弯曲应力状态与描述拉伸应力状态的广义位移函数以及剪切函数都是耦合的.没有采用工程假设,推导得到的梯度材料平板结构力学方程是精确化的.通过分析可以认识和理解,分别对应于弯曲状态与拉伸状态的应力场耦合机理以及力学响应的构成等.给出的方程及其分析过程可望能够用于类平板形式热防护材料结构的应力分析与强度设计,推进热防护材料结构的轻型化.     

正交各向异性功能梯度材料Ⅲ型裂纹尖端动态应力场

研究了无限大正交各向异性功能梯度材料Griffith裂纹受反平面剪切冲击作用的问题.材料两个方向的剪切模量假定为成比例按特定梯度变化.通过采用积分变换-对偶积分方程方法,获得了裂纹尖端动态应力场.动态应力强度因子计算结果显示:增加剪切模量梯度或增加垂直于裂纹面方向的剪切模量可以抑制动态应力强度因子的幅值.     

初应力下功能梯度磁电弹材料的Love波传播

研究初应力下含磁电弹覆盖层的半无限大功能梯度磁电弹介质中Love波的传播问题.在电磁学开路和短路的边界条件下,基于初应力下功能梯度磁电弹材料的运动方程,应力自由的表面条件和连续的界面条件得到了Love波的波速方程,为功能梯度磁电弹材料表面波器件的发展提供了理论依据.     

Investigation on the 2D Contact of Multilayer Functionally Graded Piezoelectric Material Coating Under Conducting Indenters北大核心CSCD

考虑了材料参数可按照任意函数形式变化的功能梯度压电材料(FGPM)涂层在不同形状导电压头作用下的接触问题,研究了梯度系数对功能梯度压电涂层接触力学行为的影响.建立了多层功能梯度压电材料涂层模型,运用了Fourier积分变换和传递矩阵将多层功能梯度压电材料涂层的接触问题转化为奇异积分方程.利用GaussChebyshev数值计算方法,得到了多层功能梯度压电材料涂层-基底结构在刚性导电平压头和圆柱形压头作用下的表面应力分布和电荷分布.利用数值解,分析了材料参数按照不同变化形式的FGPM涂层对最大压痕和电势的影响,还分析了功能梯度压电涂层内部的应力和电位移分布.研究结果表明,功能梯度压电材料参数的不同变化形式对结构的接触性能具有重要的影响.     

任意梯度分布功能梯度圆环的热弹性分析

对沿径向任意变化的材料参数的功能梯度圆环进行了热弹性分析.与以前关于该问题的分析不同,既不需要预先给定具体的梯度变化形式,也不需要对结构进行细分.给出一种新的有效解法将问题转换为求解Fredholm积分方程,从而通过Fredholm积分方程的解给出热应力和位移的分布情况.最后通过算例分析了内外表面受不同温度作用时,材料参数呈现梯度变化对圆环的应力和位移变化的影响,计算结果表明某些特定的材料梯度可有效缓解圆环内的热应力分布.该文得到的结果对功能梯度圆环在结构安全设计方面有重要的理论指导意义.     

线性分布载荷作用下功能梯度各向异性悬臂梁的解析解

对功能梯度各向异性弹性悬臂梁在线性分布载荷作用下的弯曲问题进行了研究．从平面应力问题的基本方程出发,假定应力函数为梁长度方向的多项式形式,由应力函数求导给出应力,利用协调方程和边界条件可完全确定应力函数．将解析解与有限元数值方法的结果进行了对比,两者吻合良好．     

应变梯度塑性Ⅰ,Ⅱ型平面应力裂纹的有限元解

将塑性应变梯度理论应用于幂硬化材料的裂纹尖端场,得出在小范围屈服条件下平面应力Ⅰ型和Ⅱ型裂纹的数值解.与现有的渐近解比较发现,Chen等人的文中裂尖附近渐近解的有效范围是0.05l量级(l为材料特征长度),远离此有效范围,有限元计算出Ⅰ型和Ⅱ型问题的应力场都趋向于经典的HRR解.在塑性区内,有限元计算只得到了应力占优的结果.     

Effect of memory dependent derivative on forced transverse vibrations in transversely isotropic thermoelastic cantilever nano-Beam with two temperature

The present research deals with the study of forced vibrations in transversely isotropic thermoelastic (TIT) nanoscale beam with two temperature (2T). Memory dependent derivative theory of thermoelasticity for clamped-free/cantilever nano-beam has been considered. The mathematical model is prepared for the nanoscale beam in a closed form with the application of Euler Bernoulli beam theory. Laplace transform method is employed to solve the problem. Forced vibrations due to exponential decaying time varying load acting vertically downward along the thickness direction of the nano-beam, Uniform load, Time harmonic load have been considered. Dynamic analysis for these forced vibrations and Static analysis has been carried out in this research. The dimensionless expressions for lateral deflection, thermal moment, temperature change, and axial stress are solved for these three forced vibrations. Response ratio has also been calculated. The analytical results have been numerically analysed using programming in MATLAB. The effect of kernel function has been depicted graphically on the lateral deflection, thermal moment, temperature change, axial stress and response ratio for all the three types of forced vibrations. Some particular cases have also been discussed.     

Progressive thermal stress distribution around a crack under Joule heating in orthotropic materials

Stress intensity factor and stress distribution at crack tips are classical problems in solids, which are closely related to the failure and reliability of materials. A crack in a nonlinearly coupled anisotropic medium, on the other hand, is much more difficult to analyze. Using the generalized complex variable method, the thermal stress problem of a crack embedded in an orthotropic medium has been analyzed, and the progressive thermal stress distributions have been obtained in closed-forms. The analysis shows that the thermal stress intensity factors are linear functions of remote thermal flux while are nonlinear functions of remote current; the thermal stress distributions under produced by thermal flux and Joule heating are similar, but not identical; the thermal stress intensity factors are linear functions with respect to the thermal expansion coefficients; with the increase of crack length, the thermal stress intensity factor caused by Joule heat increases rapidly; the thermal stress intensity factors are directly proportional to the temperature difference between the upper and lower crack surfaces and the left and right half crack surfaces divided by the square root of the crack length, and the ratios are only determined by the material parameters. These results provide a powerful tool for the failure and reliability analysis of conductive materials, and suggested that thermal stress analysis may be localized.     

Analytical inverse solution for coupled thermoelastic problem for the evaluation of contact stress during steel strip rolling

Knowledge of the contact stress between roll and strip is a critical factor in modern, high-speed rolling mills. Previously two inverse analytical methods have been developed to determine the elastic contact stress on the one hand and the heat flux or the temperature in the whole roll (and especially at the surface) on the other hand, by measuring the stress tensor inside the roll body with fibre optics and by measuring the temperature with a thermocouple fully embedded at only one point inside the roll. However measurements done by fibre optics take into account the elastic stress and the thermal stress. However the contact stress was determined under isothermal assumption, which is strongly incorrect for hot rolling conditions. In this paper, the coupled thermoelastic problem is solved analytically using the theorem of superposition and the expression of the temperature field exhibited previously. A significant improvement of the accuracy of the inverse method for reconstructing the contact stress is observed by taking into account thermal stress. Hot rolling simulation is given to demonstrate this result. The computation time is studied to rapidly optimise the industrial parameters during the rolling process, and considering that both inverse methods have been run, the computation of thermal stress does not cost significant additional CPU times.     

解析辊拔问题的变上限与参变量积分

本文建立与Ａｖｉｔｚｕｒ不同的直角坐标系速度场与应变速率场，并采用变上限积分与参变量积分获得辊拔力的上界解析解。     

Perturbation analysis of radiative effect on free convection flows in porous medium in the presence of pressure work and viscous dissipation

The effect of thermal radiation with a regular three-parameter perturbation analysis has been studied for the effects in some free convection flows of Newtonian fluid-saturated porous medium. The effects of the thermal radiation, permeability of the porous medium, pressure stress work and viscous dissipation on the flows and temperature fields have been included in the analysis. Four different vertical flows have been analyzed, those adjacent to an isothermal surface, uniform heat flux surface, a plane plume and flow generated from a horizontal line energy source, and, a vertical adiabatic surface. Rosseland approximation is used to describe the radiative heat flux in the energy equation. The numerical results of the perturbation analysis for four conditions are solved numerically by the fourth-order Runge–Kutta integration scheme. Numerical values of the main physical quantities are the skin friction and a heat transfer and total heat and mass convected downstream are presented in a tabular form with the parameters characterizing the radiation, permeability of the porous medium, pressure stress work and viscous dissipation. The obtained results are compared and a representative set is displayed graphically to illustrate the influences of the radiation, permeability of the porous medium, pressure stress work and viscous dissipation on the velocity and the temperature profiles.     

计算机求解渐开线齿轮齿廓的保角映射函数

平面弹性理论的复变函数保角映射解法可以求得齿轮的应力和位移的精确解.而相应于各种不同参数的轮齿齿廓的保角映射函数的求得却是比较困难的.以往均采用试算法,这是费时且昂贵的.作者编制了求解保角映射函数的计算机程序,并通过大量的计算证明这一程序是成功的,所取得的映射函数是精确的.从而解决了保角映射法求解渐开线齿轮应力和位移应用于实际工程计算的主要障碍.     

Study of the residual (internal) stresses in reinforced epoxy resin

An optical polarization method has been used to study the residual (internal) stresses in reinforced ED-6 epoxy resin cured with maleic anhydride. The effects of "chemical" shrinkage, volume change relaxation during during curing, and the difference linear coefficients of thermal expansion for reinforcement and resin are elucidated. It is shown that adjacent reinforcing elements interact. The stress state is investigated with reference to a model of the elementary cell of the regular structure of a unidirectional glass-reinforced plastic. The residual stresses are found as a function of the resin/reinforcement ratio.Mekhanika Polimerov, Vol. 1, No. 4, pp. 76–80, 1965     

A moving thermal dielectric crack in piezoelectric ceramics with a shearing force applied on its surface

This article conducts an exact analysis of a thermal dielectric crack moving in piezoelectric materials. Self-generating thermal and electric loadings by the crack interior are exerted on the crack surfaces as well as various external loadings including a shearing force. Fundamental solutions of the thermal and electro-elastic coupling fields are given by determining a temperature function and a harmonic function with eigenvalues properties due to material properties considered. Analytical expressions are obtained benefiting evaluation of key parameters. Numerical analysis is done and some interesting observations are found. There is a critical crack velocity within and beyond which the electric loading exerts different influences on the thermal flux of crack interior and the thermal stress intensity factor.     

Ⅰ型试件裂端三维应力结构分析之二——应力结构分析

在文献[1]的基础上,本文分别对试件纤维区和剪切唇的应力结构进行考察.纤维区的应力结构特点为:可以进行变量z分离;对称面上的应力结构可由平面应变FEM解或HRR场解经应力三维度修正获得;载荷水平及试样厚度对应力结构的影响,可由厚度方向的CTOD得到反映,所得到应力表达式大为简便与直观.对剪切唇的应力结构进行考察,发现满足一定的精度可由插值法近似获得.本文提出了一种平面应变近似程度系数,并对此进行分析,该系数可较好地反映试样厚度、型式及载荷水平.本文也对断裂参量进行了分析,指出可对CTOD进行应力三维度修正获得.