高温AlN插入层对AlGaN/GaN异质结材料和HEMTs器件电学特性的影响

研究了在GaN缓冲层中插入40 nm厚高温AlN层的GaN外延层和AlGaN/GaN异质结材料, AlN插入层可以增加GaN层的面内压应力并提高AlGaN/GaN高电子迁移率晶体管（HEMTs）的电学特性. 在精确测量布拉格衍射角的基础上定量计算了压应力的大小. 增加的压应力一方面通过增强GaN层的压电极化电场, 提高了AlGaN/GaN异质结二维电子气（2DEG）面密度, 另一方面使AlGaN势垒层对2DEG面密度产生的两方面影响相互抵消. 同时, 这种AlN插入层的采用降低了GaN与AlGaN层之间的 关键词： 高温AlN插入层 AlGaN/GaN异质结 二维电子气 应力     

淀积在不同小倾角蓝宝石衬底的n型GaN的研究

采用金属有机物化学淀积技术在不同倾角（0°—03°）的蓝宝石衬底上外延n型GaN.通过原子力显微镜观察到n型GaN均呈台阶流生长模式,02°和03°倾角衬底的n型GaN表面台阶朝向相同、分布均匀,明显地看到在0°倾角衬底的n型GaN表面由台阶重构直接导致的台阶朝向随机分布、疏密不匀的形貌.电子背散射分析表明,在0°倾角衬底的n型GaN外延层的应力随外延厚度增加而增加,而02°和03°倾角衬底的n型GaN外延层的应力没有明显的变化.电学和光学特性研究表明,02°和03°倾角衬底的n型GaN有较高的电子浓度和较低的黄光带与近带边强度之比. 关键词： 金属有机物化学淀积 氮化物 原子力显微镜 光致发光     

AlN插入层对硅衬底GaN薄膜生长的影响

利用金属有机化合物气相外延沉积技术在2inch(5.08cm)Si(111)图形衬底上生长了GaN外延薄膜,在Al组分渐变AlGaN缓冲层与GaN成核层之间引入了AlN插入层,研究了AlN插入层对GaN薄膜生长的影响。结果表明,随着AlN插入层厚度的增加,GaN外延膜(002)面与(102)面X射线衍射摇摆曲线半峰全宽明显变小,晶体质量变好,同时外延膜在放置过程中所产生的裂纹密度逐渐减小直至不产生裂纹。原因在于AlN插入层的厚度对GaN成核层的生长模式有明显影响,较厚的AlN插入层使GaN成核层倾向于岛状生长,造成后续生长的nGaN外延膜具有更多的侧向外延成分,从而降低了GaN外延膜中的位错密度,减少了GaN外延膜中的残余张应力。同时还提出了一种利用荧光显微镜观察黄带发光形貌来表征GaN成核层形貌和生长模式的新方法。     

在6H-SiC衬底上用低压MOVPE法生长AlN和GaN的过程中用(AlN/GaN)多层缓冲层来控制残余应力

人们已提出用BAlGaN四元系材料制备紫外光谱区的光发射器件.GaN和AlN二元系是这种四元材料在器件应用中的基础材料.6H-SiC衬底在氮化物生长中因其晶格失配小是一大优势,而且SiC衬底的热膨胀系数也和AlN的很接近.然而,对于AlN外延层来说,需要控制其中的残余应力,因为在SiC衬底上直接生长的AlN外延层中存在着因晶格失配所产生的压缩应力.另一方面,在SiC衬底上直接生长的GaN外延层中存在着拉伸应力.这种拉伸应力起源于GaN比衬底有着更大的热膨胀系数.本文讨论了在6H-SiC衬底上生长的氮化物外延层中残余应力的类型、数量及控制.为此目的,提出了在6H-SiC衬底上,无论是生长AlN,还是生长GaN,都可以采用(GaN/AlN)多层缓冲层的办法,作为控制残余应力的有效方法.我们还讨论了AlN和GaN外延层的结晶质量和残余应力间的关系.     

金属有机物化学气相沉积同质外延GaN薄膜表面形貌的改善

为了获得高质量的GaN薄膜材料,研究了金属有机物气相沉积系统中GaN插入层对GaN衬底同质外延层表面宏观缺陷和晶体质量的影响.研究发现,插入层生长温度是影响GaN同质外延膜表面形貌和晶体质量的关键因素.由于生长模式与插入层生长温度相关,随着插入层生长温度的降低,外延膜生长模式由准台阶流模式转变为层状模式,GaN同质外延膜表面丘壑状宏观缺陷逐渐减少,但微观位错密度逐渐增大.通过对插入层温度和厚度的优化,进一步调控外延层的生长模式,最终有效降低了外延层表面的宏观缺陷,获得了表面原子级光滑平整、位错密度极低的GaN同质外延膜,其X射线衍射摇摆曲线(002),(102)晶面半峰宽分别为125arcsec和85arcsec,表面粗糙度均方根大小为0.23nm.     

使用AlN/GaN超晶格势垒层生长高Al组分AlGaN/GaN HEMT结构

在蓝宝石衬底上生长了以AlN/GaN超晶格准AlGaN合金作为势垒的HEMT结构材料,并与传统AlGaN合金势垒样品进行了对比.在高Al组分(≥40%)情况下,超晶格势垒样品的表面形貌明显改进,电学性能特别是2DEG面电子浓度也有所改进.对超晶格势垒生长参数进行了初步优化,使得HEMT结构薄层电阻进一步降低,最后获得了251 Ω/□的薄层电阻. 关键词： AlGaN/GaN 结构 AlN/GaN超晶格 二维电子气 高电子迁移率晶体管     

晶圆键合和激光剥离工艺对GaN基垂直结构发光二极管芯片残余应力的影响

GaN基发光二极管(LED)中的残余应力状态对器件的性能和稳定性有很大影响. 通过使用三种不同的键合衬底(Al₂O₃衬底, CuW衬底和Si衬底)以及改变键合温度(290 ℃, 320 ℃, 350 ℃和380 ℃), 并且使用不同的激光能量密度(875, 945和1015 mJ·cm^-2) 进行激光剥离, 制备了不同应力状态的GaN基LED器件. 对不同条件下GaN LED进行弯曲度、Raman 散射谱测试. 实验结果表明, 垂直结构LED中的残余应力的状态是键合衬底和键合金属共同作用的结果, 而键合温度影响着垂直结构LED中的残余应力的大小. 激光剥离过程中, 一定能量密度下激光剥离工艺一般不会对芯片中的残余应力造成影响, 但是如果该工艺对GaN 层造成了微裂缝, 则会在一定程度上起到释放残余应力的作用. 使用Si衬底键合后, 外延蓝宝石衬底翘曲变大, 对应制备的GaN基垂直结构 LED中的残余应力为张应力, 并且随着键合温度的上升而变大; 而Al₂O₃和CuW衬底制备的LED中的残余应力为压应力, 但使用Al₂O₃衬底键合制备的LED中压应力随键合温度上升而一定程度变大, CuW 衬底制备的LED中压应力随键合温度上升而下降.     

基于GaN同质衬底的高迁移率AlGaN/GaNHEMT材料

研究了表面预处理对GaN同质外延的影响,获得了高电子迁移率AlGaN/GaN异质结材料.通过NH_3/H_2混合气体与H_2交替通入反应室的方法对GaN模板和GaN半绝缘衬底进行高温预处理.研究结果表明,NH_3/H_2能够抑制GaN的分解,避免粗糙表面,但不利于去除表面的杂质,黄光带峰相对强度较高;H_2促进GaN分解,随时间延长GaN分解加剧,导致模板表面粗糙不平,AlGaN/GaN HEMT材料二维电子气迁移率降低.采用NH_3/H_2混合气体与H_2交替气氛模式处理模板或衬底表面,能够清洁表面,去除表面杂质,获得平滑的生长表面和外延材料表面,有利于提高AlGaN/GaN HEMT材料电学性能.在GaN衬底上外延AlGaN/GaN HEMT材料,2DEG迁移率达到2113 cm~2/V·s,电学性能良好.     

AlGaN表面坑状缺陷及GaN缓冲层位错缺陷对AlGaN/GaN HEMT电流崩塌效应的影响

利用金属有机气相外延(MOVPE)技术生长了具有不同AlGaN表面坑状缺陷和GaN缓冲层位错缺陷密度的AlGaN/GaN 高电子迁移率晶体管(HEMT)样品,并对比研究了两种缺陷对器件栅、漏延迟电流崩塌效应的影响.栅延迟测试表明,AlGaN表面坑状缺陷会引起栅延迟电流崩塌效应和源漏电阻的增加,而且表面坑状缺陷越多,栅延迟电流崩塌程度和源漏电阻的增加越明显.漏延迟测试显示,AlGaN表面坑状缺陷对漏延迟电流崩塌影响不大,而GaN缓冲层位错缺陷主要影响漏延迟电流崩塌.研究结果表明,AlGaN表面坑状缺陷和Ga 关键词： AlGaN/GaN HEMT 电流崩塌 坑状缺陷 位错缺陷     

AlGaN/GaN异质结载流子面密度测量的比较与分析

对MOCVD技术在蓝宝石衬底上生长的不同Al组分AlGaN/GaN异质结进行了范德堡法Hall测量和电容-电压(C-V)测量，发现Hall测量载流子面密度值大于C-V测量值，并且随着AlGaN层Al组分的增加，两种测量值都在增加，同时它们的差值也在增加.认为产生这一结果的原因有两方面.一方面，Ni/Au肖特基金属淀积在AlGaN/GaN异质结上，改变了AlGaN势垒层的表面状态，使得一部分二维电子气(2DEG)电子被抽取到空的施主表面态中，从而减小了AlGaN/GaN异质结界面势阱中的2DEG浓度.随着势垒层Al组分的增加，AlGaN层产生了更多的表面态，从而使得更多的电子被抽取到了空的表面态中.另一方面，由于C-V测量本身精确度受到串联电阻的影响，使得测量电容小于实际电容，从而低估了载流子浓度.     

GaN grown on Si(1 1 1) with step-graded AlGaN intermediate layers

The authors report the growth of crack-free GaN on Si(1 1 1) substrate with step-graded AlGaN intermediate layers all grown at 1120 °C. By preparing all these layers at high-temperature, we can simplify the growth proceduce and minimize the growth time. Using X-ray diffraction and transmission electron microscopy, it was found that the high-temperature step-graded AlGaN intermediate layers can effectively reduce the tensile stress on GaN epitaxial layers. Photoluminescence and Raman measurements also indicate that we can improve the crystal quality of GaN by inserting the step-graded AlGaN intermediate layers.     

Optical and structural investigation of a-plane GaN layers on r-plane sapphire with nucleation layer optimization

Nonpolar a-plane GaN epilayers are grown on several r-plane sapphire substrates by metal organic chemical vapour deposition using different nucleation layers:(A) a GaN nucleation layer deposited at low temperature(LT);(B) an AlN nucleation layer deposited at high temperature;or(C) an LT thin AlN nucleation layer with an AlN layer and an AlN/AlGaN superlattice both subsequently deposited at high temperature.The samples have been characterized by Xray diffraction(XRD),atomic force microscopy and photoluminescence.The GaN layers grown using nucleation layers B and C show narrower XRD rocking curves than that using nucleation layer A,indicating a reduction in crystal defect density.Furthermore,the GaN layer grown using nucleation layer C exhibits a surface morphology with triangular defect pits eliminated completely.The improved optical property,corresponding to the enhanced crystal quality,is also confirmed by temperature-dependent and excitation power-dependent photoluminescence measurements.     

Strain Effect on Photoluminescences from InGaN MQWs with Different Barriers Grown by MOCVD

InGaN/GaN MQWs, InGaN/AlGaN MQWs and InGaN/AlInGaN MQWs are grown on （0001） sapphire substrates by MOCVD. Membrane samples are fabricated by laser lift-off technology. The photoluminescence spec-ra of membranes show a blue shift of peak positions in InGaN/GaN MQWs, a red shift of peak positions in InGaN/AlGaN MQWs and no shift of peak positions in InGaN/AIlnGaN MQWs from those of samples with substrates. Different changes in Raman scattering spectra and HR-XRD （0002） profile of InGaN/AlInGaN MQWs, from those of InGaN/GaN MQWs and InGaN/AlGaN MQWs, are observed. The fact that the strain changes differently among InGaN MQWs with different barriers is confirmed. The AIlnGaN barrier could adjust the residual stress for the least strain-induced electric field in InGaN/AIlnGaN quantum wells.     

Strain modification of AlGaN layers using swift heavy ions

Epitaxial AlGaN/GaN layers grown by molecular beam epitaxy (MBE) on SiC substrates were irradiated with 150 MeV Ag ions at a fluence of 5×10¹² ions/cm². The samples used in this study are 50 nm Al_0.2Ga_0.8N/1 nm AlN/1 μ m GaN/0.1 μ m AlN grown on SI 4H-SiC. Rutherford backscattering spectrometry/channeling strain measurements were carried out on off-normal axis of irradiated and unirradiated samples. In an as-grown sample, AlGaN layer is partially relaxed with a small tensile strain. After irradiation, this strain increases by 0.22% in AlGaN layer. Incident ion energy dependence of dechanneling parameter shows E ^1/2 dependence, which corresponds to the dislocations. Defect densities were calculated from the E ^1/2 graph. As a result of irradiation, the defect density increased on both GaN and AlGaN layers. The effect of irradiation induced-damages are analyzed as a function of material properties. Observed results from different characterization techniques such as RBS/channeling, high-resolution XRD and AFM are compared and complemented with each other to deduce the information. Possible mechanisms responsible for the observations have been discussed in detail.     

Photoreflectance investigations of AlGaN/GaN heterostructures with a two dimensional electron gas

Undoped AlGaN/GaN heterostructures with different content and thickness of AlGaN layer are investigated by photoreflectance (PR) spectroscopy. We have observed PR resonances related to an absorption in both GaN and AlGaN layers. The character of these resonances has been analyzed, and PR lines associated with excitonic and band-to-band absorption in the GaN layer and band-to-band absorption in the AlGaN layer have been identified. The transition related to band-to-band absorption possesses characteristic Franz–Keldysh oscillations (FKOs) associated with a built-in electric field. The electric field in the AlGaN layer obtained on the basis of the analysis of FKOs has been found to be in the range of 244–341 kV/cm. The value of the field has been found to decrease with the increase in AlGaN thickness and to increase with the increase in Al concentration. The surface potential for AlGaN layers has been found to increase with the increase in Al mole fraction and has been estimated to be in the range of 1.0–1.7 eV.     

Effects of the strain relaxation of an AlGaN barrier layer induced by various cap layers on the transport properties in AlGaN/GaN heterostructures

The strain relaxation of an AlGaN barrier layer may be influenced by a thin cap layer above, and affects the transport properties of AlGaN/GaN heterostructures. Compared with the slight strain relaxation found in AlGaN barrier layer without cap layer, it is found that a thin cap layer can induce considerable changes of strain state in the AlGaN barrier layer. The degree of relaxation of the AlGaN layer significantly influences the transport properties of the two-dimensional electron gas (2DEG) in AlGaN/GaN heterostructures. It is observed that electron mobility decreases with the increasing degree of relaxation of the AlGaN barrier, which is believed to be the main cause of the deterioration of crystalline quality and morphology on the AlGaN/GaN interface. On the other hand, both GaN and AlN cap layers lead to a decrease in 2DEG density. The reduction of 2DEG caused by the GaN cap layer may be attributed to the additional negative polarization charges formed at the interface between GaN and AlGaN, while the reduction of the piezoelectric effect in the AlGaN layer results in the decrease of 2DEG density in the case of AlN cap layer.     

The low-temperature mobility of two-dimensional electron gas in AlGaN/GaN heterostructures

To reveal the internal physics of the low-temperature mobility of two-dimensional electron gas （2DEG） in Al- GaN/GaN heterostructures, we present a theoretical study of the strong dependence of 2DEG mobility on Al content and thickness of AlGaN barrier layer. The theoretical results are compared with one of the highest measured of 2DEG mobility reported for AlGaN/GaN heterostructures. The 2DEG mobility is modelled as a combined effect of the scat- tering mechanisms including acoustic deformation-potential, piezoelectric, ionized background donor, surface donor, dislocation, alloy disorder and interface roughness scattering. The analyses of the individual scattering processes show that the dominant scattering mechanisms are the alloy disorder scattering and the interface roughness scattering at low temperatures. The variation of 2DEG mobility with the barrier layer parameters results mainly from the change of 2DEG density and distribution. It is suggested that in AlGaN/GaN samples with a high Al content or a thick AlGaN layer, the interface roughness scattering may restrict the 2DEG mobility significantly, for the AlGaN/GaN interface roughness increases due to the stress accumulation in AlGaN layer.     

Influence of thermal stress on the relative permittivity of the AlGaN barrier layer in an AlGaN/GaN heterostructure Schottky contacts

Ni Schottky contacts on AlGaN/GaN heterostructures were fabricated. Some samples were thermally treated in a furnace with N₂ ambience at 600 °C for different times (0.5 h, 4.5 h, 10.5 h, 18 h, 33 h, 48 h, and 72 h), the others were thermally treated for 0.5 h at different temperatures (500 °C, 600 °C, 700 °C, and 800 °C). With the measured current—voltage (I—V) and capacitance—voltage (C—V) curves and by self-consistently solving Schrodinger's and Poisson's equations, we found that the relative permittivity of the AlGaN barrier layer was related to the piezoelectric and the spontaneous polarization of the AlGaN barrier layer. The relative permittivity was in proportion to the strain of the AlGaN barrier layer. The relative permittivity and the strain reduced with the increased thermal stress time until the AlGaN barrier totally relaxed (after 18 h at 600 °C in the current study), and then the relative permittivity was almost a constant with the increased thermal stress time. When the sample was treated at 800 °C for 0.5 h, the relative permittivity was less than the constant due to the huge diffusion of the contact metal atoms. Considering the relation between the relative permittivity of the AlGaN barrier layer and the converse piezoelectric effect, the conclusion can be made that a moderate thermal stress can restrain the converse piezoelectric effect and can improve the stability of AlGaN/GaN heterostructure devices.