首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 31 毫秒
1.
以分光光度法测定高含量膨润土吸蓝量,应用正交试验设计对分光光度法的实验条件进行优化,确定的最佳实验条件:煮沸时间为5 min,4%焦磷酸钠溶液加入体积为20 mL,0.01 mol/L亚甲基蓝溶液加入体积为30mL,振荡时间为15 min。该法与滴定法对比,测定值相对误差在4%以内,相对标准偏差为1.04%,可满足高纯度膨润土吸蓝量的分析要求。  相似文献   

2.
The quantitative extraction of cationic surfactant (CS+) in river sediments was studied. Further, the developed method was applied to the spectrophotometric determination of CS+ in urban river sediment samples by solid-phase extraction with membranes. A mixture of methanol and hydrochloric acid was proposed as an eluent. Dried sediment was digested in the eluent under ultrasonic irradiation. After elution, the eluent was evaporated to almost dryness. The residue was dissolved in a small volume of methanol and diluted to a certain volume with water. The pH of the solution was adjusted to 4-5 to separate iron and some other metals as precipitates of hydroxides. The solution was passed through two-piled membranes: first glass-fiber and then polytetrafluoroethylene (PTFE) membranes. A small volume of methanol was passed through the membranes to elute any CS+ retaining on the membranes. After passing the methanol solution through a cationic exchange resin column, the retained CS+ was eluted with methanol containing a high concentration of sodium chloride. Water, Bromophenol Blue (BPB) and hydrochloric acid were added to the solution. The solution was passed through a mixed cellulose ester membrane filter to retain an ion associate of CS+.BPB-. The retained ion associate was dissolved in a small volume of N,N-dimethylformamide together with the membrane filter, followed by the addition of triethanolamine to make the solution alkaline. The absorbance due to BPB2- was measured at 603 nm against a reagent blank. This method was applied to the determination of CS+ in river water and sediment. A cationic surfactant in sediments at 10(-5) mol kg-1 levels was detected with satisfactory precision. It was found that CS+ was about 500-fold enriched in the sediment from water at the place where domestic wastewater was discharged.  相似文献   

3.
建立了用硫酸分离-火试金重量法测定碲化铜中的金和银含量的方法。用硫酸溶解碲化铜样品,过滤,除去铜和碲,得到含金、银的沉淀物,沉淀物经灰化、配料、高温熔融制得铅扣。将铅扣灰吹,得到金银合粒,用硝酸溶解分离金,用重量法测定金含量。用金银合粒的质量扣除金粒的质量和分金液、洗液中杂质的质量即为银含量。采用灰皿、残渣熔融法补正,或用含碲、铜物料做基体加入纯金、纯银同试样方法测定,根据金、银的回收率加以补正,从而得到试样中的碲含量。实验结果表明,浓硫酸的加入量为30 mL,残余量应不少于15 mL。火试金中硅酸度为1左右,试样进炉温度以900℃为宜。该方法金、银测定结果的相对标准偏差分别为0.33%~1.97%,0.28%~1.27%(n=9)。金的回收率为98.5%~100.2%,银的回收率为95.5%~101.4%。该法满足生产控制检测和贸易结算的要求。  相似文献   

4.
Quantitative and selective analysis of lactose by capillary electrophoresis   总被引:2,自引:0,他引:2  
Summary A CE method has been validated for the analysis of batches of lactose used as a pharmaceutical raw material. This method was shown to be selective for lactose and was found to be quantitative. The separation was achieved due to on-capillary chelation of the lactose with borate ion. The resulting complex was detected at 195nm. An internal standard is employed to improve injection precision and detector linearity. A system peak occurred in the separation and was systematically investigated to show that it was not sample related. The method was validated and successfully submitted to regulatory authorities and is now in routine use in a number of our quality control laboratories.  相似文献   

5.
Methods of increasing the enzymatic digestibility of waste newspaper by adding Tween (TW)-20 and 80 surfactants were investigated. Tween-series surfactants were selected because these surfactants increase cellulase activity during enzymatic hydrolysis and do not inhibit cell growth in downstream fermentation processes. When surfactant was used in a pretreatment, a benefic effect was expected in the enzymatic hydrolysis stage owing to surfactant carry-over from the pretreatment stage immediately upstream of the hydrolysis. However, because it was necessary to wash the pretreated substrate with water to remove inhibitors produced during pretreatment, no added benefit was obtained. When surfactant was used in the pretreatment only, it was found that it had a marked effect on digestibility and that this effect was higher at lower enzyme loadings. Also, TW-80 was found to be more effective than TW-20, and the addition of enzyme and TW-80 to substrate at the beginning of enzyme reaction was found to most effectively increase digestibility. When TW-80 was added into either the pretreatment stage or the hydrolysis stage the digestibilities of untreated sample increased by approx 40%, whereas an increase of only 45% was observed when TW-80 was added to both stages. These results show that the addition of surfactant to either the pretreatment or the enzymatic hydrolysis stage is sufficient to increase digestibility.  相似文献   

6.
化探金样品前处理过程中消解、富集、解吸等环节控制不严格,往往会导致最后数据处理产生过高的校正系数。为了降低校正系数,用统计学的方法对实验过程进行了详细分析,确定了主要影响因素。将水浴时间延长并保温3 h以上,泡塑大小改为0.2 g,清洗时间不大于15 s,解吸到上机时间间隔小于5 h。方法改进后,检测结果校正系数有了明显改善,从改进前有40%批次的校正系数大于1.2,降到了全部小于1.2,甚至不用校正。方法改进后降低了实验过程的误差,提高了分析测试结果的稳定性。  相似文献   

7.
为减缓温室效应,将CO_(2)转换成高附加值的甲醇是减少CO_(2)排放的有效途径,而高效催化剂是CO_(2)加氢制甲醇反应规模化的关键.可调控合成的具有量子尺寸效应的纳米催化剂在该反应上具有独特的优势.因此我们深入探讨了反应机理,综述了纳米材料在CO_(2)加氢制甲醇中的研究进展,最后给出了高效催化剂可能的发展方向.  相似文献   

8.
When doxorubicin was encapsulated into liposomes by freeze-thawing, the percentage of encapsulated doxorubicin (EN%) was found to vary according to the type of buffer solution used. The reason for this was investigated in the present report. Drug-free liposomes prepared by hydration were mixed with doxorubicin dissolved in a certain type of buffer solution that shows a pH decrease on freezing, and this mixture was subjected to freeze-thawing. Doxorubicin was encapsulated by the liposomes due to the difference in pH between freezing and thawing. EN% depended on the pH of the buffer solution before freezing and increased significantly at over pH 7. About 60% of doxorubicin was encapsulated into liposomes after the Ist freeze-thawing cycle, and EN% was increased gradually with the number of freeze-thawing cycles. The addition of sugar to the experimental system was seen to affect doxorubicin encapsulation and the particle size of liposomes.  相似文献   

9.
The passivation phenomenon of rhodium was investigated in fused lithium chloride + potassium chloride eutectic by means of the potential sweep method. The current-potential curve obtained showed a typical N-shaped negative impedance. An anodic current rise was observed at +0.3 V vs. Ag/AgCl (0.1). The current was controlled by mass transfer and was ascribed to the dissolution of rhodium into rhodium(III) ions. The observed Flade potential was +0.45 V at 400°C. The passivation was found to occur due to the precipitation of supersaturated Rh(III) chloride onto the electrode surface. The residual current for the passivation was fairly high and the current increased significantly as the temperature was made higher. The dissolution current of rhodium into Rh(III) ions decreased with increase in the concentration of oxide ions. The fact revealed that the rhodium was passivated preferentially due to the formation of Rh(III) oxide. The residual current of the oxide passivation film was low enough. The thickness of the film corresponded to 10–20 atomic layers of the parent metal. Rhodium showed another anomalous passivation due to the formation of oxide. The oxide was formed at ?0.3 V and was reduced at ?0.6 V. It was considered to be a low valence rhodium oxide, RhO or Rh2O. Rhodium was found to have a low chlorine overpotential. However, it was redissolved at the chlorine evolution region, above +1.25 V. The dissolution was not prevented even in the oxide ion containing melts.  相似文献   

10.
利用原子吸收分光光度法分别用钾空心阴极灯测钠、锌空心阴极灯测铜,标准曲线线性良好,相关系数均在0.999以上。钾灯测量钠质控样结果为0.747 mg/L,在质控样标称值范围(0.712±0.049)mg/L之内。锌灯测量铜质控样结果为1.23 mg/L,在质控样标称值范围(1.19±0.05)mg/L之内。钾灯测钠的相对标准偏差为0.47%(n=6),加标回收率为99.8%。锌灯测铜的相对标准偏差为0.53%(n=6),加标回收率为103%。一灯多用在环境监测工作中是可行的。  相似文献   

11.
主要针对三种原材料中的Al含量和Si含量的分析方法进行讨论。采用容量法对其中的Al含量进行测定,在酸性溶液中,加入过量的EDTA溶液络合铝并掩蔽残余元素。在微酸性溶液中以二甲酚橙为指示剂,用氯化锌标准溶液滴定过量的EDTA,以氟化铵络合铝而游离出等量的EDTA。再用氯化锌标准溶液滴定至溶液呈橙红色即为终点。根据氯化锌标准溶液的消耗量换算出Al2O3的含量。采用重量法对其中Si含量进行测定,将熔融后的试样进行处理,使之生成硅酸沉淀。经灼烧、称重后以硫酸、氢氟酸进行挥硅处理,再灼烧称重,根据两次质量之差换算出SiO2的含量。两种分析方法均为经典化学分析方法,其分析结果准确可靠,并且具有广泛的使用性。  相似文献   

12.
The silica coating has attracted much attention because of its superior corrosion resistance with almost no harm to human health and to the environment. In this study, a two layered silica film was tried to get an enhanced corrosion resistance. The silica film was prepared on the hairline finish 304 stainless steel surfaces by-a-spray- and subsequent-dip-coating process. The spray coating solution was prepared by mixing sodium silicate solution, silica colloid, tetraethyl orthosilicate (TEOS), methyltriethoxysilane (MTES), ethanol, and distilled water. Then the solution was sprayed onto the stainless steel surface, and was dried and heat treated. The dip coating solution was prepared by a simple mixing of TEOS and acidic water into ethanol, and the prior spray coated sample was dipped into the solution. The outer dip coated layer was intended to cover spray coated rough and porous layer and hence to enhance the corrosion resistance. A homogeneous and crack free surface was successfully obtained after the dip coating. The prepared silica film was characterized using scanning electron microscopy, potentiodynamic polarization scan, and electrochemical impedance spectroscopy. The two layered film showed an enhanced corrosion resistance. The enhancement was attributed to a protecting effect of the dip coated layer where the diffusion of ionic species was successfully impeded.  相似文献   

13.
利用现场压电红外发射光谱电化学技术研究邻联甲苯胺(OTD)在金电极上的电化学行为.压电电化学结果表明:电位范围对OTD氧化的影响很大.当电位扫至0.6 V时,氧化过程中中间体的生成和溶解的同时,部分未溶中间体在电极表面沉积.当电位大于0.65 V时,还有OTD的电化学氧化聚合.压电红外反射光谱电化学结果表明中间体是OTD第一氧化产物之间相互作用形成的.进一步考察了肝素大阴离子对OTD的氧化的影响.  相似文献   

14.
Two lasers working in the UV part of the spectrum have been used for the analysis of glass samples. An XeCl excimer laser (308 nm) and a Nd:YAG laser operating at the third harmonic (355 nm) and the fourth harmonic (266 nm) have been selected. The energy was 100 mJ and 5 mJ for the excimer laser and the Nd:YAG laser, respectively. Because of different spot sizes, the fluence was of the same magnitude for both lasers. Crater characterization indicated that the laser ablation efficiency was similar for the two lasers when normalized to the same energy. However, the XeCl was found to be more efficient when the results were normalized to irradiance unit. The amount of probed material and ablated material was measured, leading to an efficiency higher than 80%. The influence of the glass colour and the laser wavelength was evaluated. The XeCl laser provided the largest amount of material but was sensitive to the glass colour. This laser was mainly suitable for bulk analysis. In contrast, the Nd:YAG, particularly at 266 nm, was insensitive to the glass colour and was appropriate for localized analysis. Inductively coupled plasma atomic emission spectrometry was used for atomization and excitation of the ablated material. A good agreement was found between the temporal behaviour of the amount of ablated material and the analyte signal.  相似文献   

15.
A novel analytical method for determination of total amount of chondroitin sulfate (CS) based on its conversion to desulfated chondro-disaccharide via an enzyme-catalyzed reaction, was developed. Using the in-capillary enzyme reaction, the method was also applied to the successful construction of an on-line analytical system. Within this system, electrophoretic migration was used to mix zones containing the enzyme mixture (chondroitinase ABC, chondro-4-sulfatase, chondro-6-sulfatase and 2-o-sulfatase) and the substrate (CS). The reaction was then allowed to proceed in the presence of a weak electric field and, finally, the product (desulfated chondro-disaccharide) of enzyme reaction migrated to the detector under the influence of an applied electric field. A polyvinyl alcohol-coated capillary was used to reduce protein adsorption. Desulfated chondro-disaccharide was successfully migrated toward the anode in 10 mM Tris-acetate buffer (pH 7.0) under reversed polarity and detected at 232 nm. The established method was validated and demonstrated to be applicable in the determination of total amount of CS in a commercial ophthalmic solution. No interference from the formulation excipients was observed. Good linearity was obtained, with correlation coefficients above 0.999. Recoveries and precisions ranged from 100.0 to 100.5%, and from 0.2 to 0.6% of the relative standard deviation, respectively. Good agreement was obtained between the established method and traditional photometric method based on carbazole reaction. In this study, application of the method to disaccharide compositional analysis was also performed.  相似文献   

16.
研究了氢醌与胆红素的作用过程,发现氢醌在碱性条件下可促使胆红素氧化,且胆红素被氧化成胆绿素,此反应过程被证实为自由基反应,考察了介质条件,抗氧化剂等反应过程的影响及其它酚类物质对胆红素氧化的作用情况。  相似文献   

17.
Calmodulin (CaM) was used as an affinity tail to facilitate the purification of the green fluorescent protein (GFP), which was used as a model target protein. The protein GFP was fused to the C-terminus of CaM, and a factor Xa cleavage site was introduced between the two proteins. A CaM-GFP fusion protein was expressed in E. coli and purified on a phenothiazine-derivatized silica column. CaM binds to the phenothiazine on the column in a Ca(2+)-dependent fashion and it was, therefore, used as an affinity tail for the purification of GFP. The fusion protein bound to the affinity column was then subjected to a proteolytic digestion with factor Xa. Pure GFP was eluted with a Ca(2+)-containing buffer, while CaM was eluted later with a buffer containing the Ca(2+)-chelating agent EGTA. The purity of the isolated GFP was verified by SDS-PAGE, and the fluorescence properties of the purified GFP were characterized.  相似文献   

18.
利用X射线微区分析的方法,对吸附交联法得到的固定化脂肪酶的微观活性进行了分析。结果表明:以合成出的大孔吸附树脂为固定化酶栽体,酶活较高,活性脂肪酶分布较均匀。并得到了固定化脂肪酶的活性定位的最佳条件。  相似文献   

19.
采用硅胶柱层析-气相色谱法对月桂酸甲酯乙氧基化物(LME)中副产物二酯进行了定量分离与测定,同时考察了不同条件下合成的LME中二酯含量的变化规律。结果表明:LME中二酯含量随环氧乙烷(EO)加合数(n)的增加而先增大后趋平衡,当加合数n为8时,其质量分数为2.13%;并随反应温度升高而增大;随原料甲酯所含碳原子个数增加而降低。  相似文献   

20.
以铁素体不锈钢430为研究对象,通过添加0.06%稀土,可改善铁素体不锈钢430的凝固组织,使凝固组织中的柱状晶区域减小,等轴晶区扩大;可改变铁素体不锈钢430中夹杂物的形貌、组分和分布,夹杂物由脆性夹杂改性为塑性夹杂,同时夹杂物的尺寸减少;有利于铁素体不锈钢430热轧板组织的改善,晶粒进一步细化,晶粒度由6级提高到8级;可改变铁素体不锈钢430的冲击断口形貌,断口形貌由脆性解理断口向韧性断口转变。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号