壳聚糖亲和磁性毫微粒的制备及其对蛋白质的吸附性能研究

以壳聚糖为包裹材料包埋自制的磁流体 ,制备了具有核 壳结构的磁性毫微粒 ,并偶联色素配基CibacronBlue 3GA(偶联量 1 4 .5μmol/mL)得到了一种新型亲和磁性毫微粒 .结果表明 ,所得亲和磁性微球具有较窄的粒径分布、形状规整 .以牛血清白蛋白 (BSA)和溶菌酶 (Lys)为目标蛋白 ,考察了该亲和磁性毫微粒的吸附性能 ,发现其对BSA和Lys的吸附量分别为 4和 2 8mg/g,吸附行为满足Langmuir吸附等温式 ,且对时间依赖性小而对溶液离子强度敏感 .     

白蛋白在以染料为配基的醋酸纤维滤棒上的等温吸附行为(英文)

 以醋酸纤维滤棒为基质 ,染料CibacronBlueF3GA为配基 ,合成了一种新的染料亲和介质 ;分别以牛血清白蛋白 (BSA)和人血清白蛋白 (HSA)为对象 ,用静态法进行了吸附实验 ,得到了相应的亲和等温吸附曲线 ;对曲线按Langmuir模型和Freundlich模型分别进行拟合 ;结果表明 ,醋酸纤维滤棒染料亲和介质对BSA和HSA的等温吸附遵循Freundlich模型。采用该亲和介质装柱并分离实际样品人血浆 ,可得到纯化的人血清白蛋白。     

染料壳聚糖微球的制备及其对牛血清白蛋白(BSA)吸附性能的研究

采用反相悬浮交联法制备壳聚糖微球,对微球进行羟丙基氯化及氨基化,并偶联色素配体Cibacron Blue F3GA,得到一种新型染料亲和吸附剂.以牛血清白蛋白(BSA)为目标蛋白,考察了该染料亲和吸附剂的吸附性能,发现其对BSA有较高的吸附量(95.2mg/g),吸附行为满足Langmuir吸附等温式.负载牛血清白蛋白的微球容易洗脱,洗脱率高达99％.     

辛巴蓝F3G-A固载的交联聚乙烯醇作为亲和色谱填料

以乙酸丁酯和正庚烷作为致孔剂,乙酸乙烯酯与异氰酸三烯丙基酯进行悬浮共聚、经碱性水解得到大孔交联聚乙烯醇树脂。交联聚乙烯醇与环氧氯丙烷在碱性条件下反应,得到含有环氧基的树脂。含有环氧基的树脂与6-氨基己基-N'-辛巴蓝F3G-A反应,制得固载辛巴蓝F3G-A (一种三嗪染料) 的交联聚乙烯醇树脂。将固载辛巴蓝F3G-A的交联聚乙烯醇树脂作为亲和色谱填料,对五种蛋白质 (细胞色素c、溶菌酶、牛血清白蛋白、胰岛素和乳酸脱氢酶) 进行了色谱分离。     

染料结合2μm无孔硅胶亲和填料的制备与应用

在２μｍ无孔硅胶表面键合３ 氨丙基 三乙氧基硅烷（ＡＰＳ）,并与三嗪染料活性蓝Ｆ３ＧＡ（ＣｉｂａｃｒｏｎＢｌｕｅＦ３ＧＡ,ＣＢ）反应,制得亲和色谱填料,并采用扫描电镜、元素分析、ｐＨ稳定性测试对此填料进行鉴定与表征。该填料具有良好的色谱性能,且对生物大分子有一定的亲和选择性,改变ｐＨ值及离子强度对溶菌酶的结合量有明显影响,可用于分离卵清蛋白（Ｏｖａｌ）和溶菌酶（Ｌｙｓ）,且对α ,β ,γ 球蛋白有不同的亲和作用,并可从鸡蛋清中制备少量溶菌酶。     

开管毛细管亲和液相色谱初探

 提出了一种新的亲和色谱模式开管毛细管亲和液相色谱。在内径为 5 0 μm的毛细管内表面键合一层三嗪染料配体 ,利用毛细管电泳仪的压力系统进行亲和色谱实验。采用流动相切换洗脱技术 ,牛血清白蛋白和溶菌酶获得了有效的分离。连续运行 10次 ,溶菌酶的出峰时间、峰面积和峰高的相对标准偏差分别为0 1% ,4 3% ,3 7%。在 8 6ng～ 2 8 7ng范围内 ,溶菌酶的进样量与峰面积和峰高都呈线性关系 ,其相关系数分别为 0 9946和 0 9988。     

一种分离抗凝血酶Ⅲ的高效亲和色谱填料的制备及表征

以聚甲基丙烯酸环氧丙酯微球 ( PGMA)为基质 ,利用还原氨化方法将肝素键合在其表面上 ,得到一种以肝素为配基的高效亲和色谱填料 ,该填料对抗凝血酶 的亲和容量为 1 .2 mg/g,对抗凝血酶 和人血清白蛋白的回收率分别为 96.9%和 94 .4 % .利用前沿色谱法测定了肝素与抗凝血酶 之间的表观解离常数为 1 .96× 1 0 - 5mol/L.利用该填料可直接从人血浆中分离出抗凝血酶     

高效疏水作用色谱法对还原变性溶菌酶的折叠研究

首次用高效疏水相互作用色谱(HPHIC)研究了还原变性溶菌酶(Lys)的复性。对还原变性Lys在3种疏水性不同的色谱柱上的复性情况进行了考察,发现还原变性Lys在疏水性最弱的XDM-GM1型色谱柱上的复性效率最高,当Lys质量浓度为2.0 g/L时,其复性效率可达到94.6%。     

嵌段共聚温敏亲和色谱固定相的制备及其对抗体的分离纯化

抗体药物在癌症治疗和免疫诊断中起着重要作用，但抗体的分离纯化通常采用酸性洗脱，易导致抗体聚集失活等问题。本研究以硅胶为基质，以温敏嵌段聚合物聚[(N-异丙基丙烯酰胺)-b-4-乙烯基吡啶](P[NIPAM-b-4VP])为间隔臂，以4-巯基乙基吡啶(MEP)为配基，制备了一种嵌段共聚温敏亲和色谱固定相SiO₂-P[NIPAM-b-4VP]-MEP,并以牛血清白蛋白(BSA)和γ-球蛋白为模型蛋白，对制备的温敏亲和色谱固定相的色谱性能进行了表征。分别考察了流动相盐浓度和温度对二者分离性能的影响。结果表明，在40℃时该固定相只选择性保留γ-球蛋白，而不保留BSA;在5℃时采用含0.6 mol/L NaCl的Tris-HCl(pH 8.0)缓冲溶液进行洗脱，γ-球蛋白的质量回收率为92.7%。该固定相对γ-球蛋白的吸附量为(71.5±2.1) mg/g(n=3),是传统温敏亲和色谱固定相SiO₂-PNIPAM-MEP的2倍。将该固定相用于人血清中IgG的分离纯化，仅通过改变流动相温度和盐浓度即可一步实现对抗体的分离纯化，纯度大于97.4%±0.7%...     

肝素温度敏感色谱填料的制备与性能研究

利用自由基聚合法制备了含有聚(N-异丙基丙烯酰胺/N-丙烯酰氧琥珀酰亚胺)和肝素共聚物的温度敏感的亲和色谱填料; 通过热失重分析得到该填料表面聚合物的接枝率为9.45%; Elison-Morgan 法测定该填料表面的肝素含量为3.6mg/g. 将其用作HPLC 固定相, 分离苯和氢化可的松, 表明该色谱固定相具有温度敏感特性; 该色谱柱对凝血酶具有较强的亲和作用, 通过控制温度缩短了凝血酶的释放时间, 回收率为81.4%, 这为蛋白质的分离提供了一个快速有效的方法.     

Albumin separation with Cibacron Blue carrying macroporous chitosan and chitin affinity membranes

Cibacron Blue F3GA, Procion Red HE-3B and Procion Blue MX-R were immobilized on macroporous chitosan and chitin membranes with concentrations as high as 10–200 μmol/ml membrane. These dyed membranes were chemically and mechanically stable, could be reproducibly prepared, and operated at high flow rates. Human serum albumin (HSA) and bovine serum albumin (BSA) were selected as model proteins, and their adsorption on and desorption from the dyed chitosan membranes investigated. The Cibacron Blue F3GA membranes had a higher protein adsorption capacity, much greater for HSA than BSA, than the other dyed membranes. About 8.4 mg HSA/ml membrane were adsorbed at saturation by Cibacron Blue F3GA–chitosan membranes from a 0.05 M Tris–HCl/0.05 M NaCl, pH 8 solution. The chitin membranes had a lower dye content and hence a lower protein adsorption capacity than the chitosan membranes. The effects of important operation parameters (flow rate, protein concentration and loading) were also investigated. Cibacron Blue F3GA–chitosan membranes were employed for the separation of HSA from human plasma and high purity HSA thus obtained. This suggests that these membranes could be used for large-scale plasma fractionation.     

Dye attached poly(hydroxyethyl methacrylate) cryogel for albumin depletion from human serum

Cibacron Blue F3GA was immobilized on poly(hydroxyethyl methacrylate) cryogel and it was used for selective and efficient depletion of albumin from human serum. The poly(hydroxyethyl methacrylate) was selected as the basic component because of its inertness, mechanical strength, chemical and biological stability, and biocompatibility. Cibacron Blue F3GA was covalently attached to the poly(hydroxyethyl methacrylate) cryogel to produce poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel affinity column. The poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel was characterized with respect to gelation yield, swelling degree, total volume of macropores, Fourier Transform Infrared spectroscopy, and scanning electron microscopy. It was found that the maximum amount of adsorption (343 mg/g of dry cryogel) obtained from experimental results is very close to the calculated Langmuir adsorption capacity (345 mg/g of dry cryogel). The maximum adsorption capacity for poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel column was obtained as 950 mg/g of dry cryogel for nondiluted serum. The adsorption capacity decreased with increasing dilution ratios while the depletion ratio of albumin remained as 77% in serum sample. Finally, the poly(hydroxyethyl methacrylate)-Cibacron Blue F3GA cryogel was optimized for using in the fast protein liquid chromatography system for rapid removal of the high abundant proteins from the human serum.     

High-performance liquid chromatography of proteins: purification of alpha-fetoprotein from fetal calf serum

High-performance liquid chromatography was utilized for the purification of bovine alpha-fetoprotein (BAFP) from fetal calf serum (FCS). An initial step in the purification involved absorption of charcoal delipidated FCS on Cibacron Blue F3GA gel. The Cibacron Blue pre-purified FCS was then chromatographed on a Polyanion SI weak anion-exchange column. The BAFP isolated had a purity of greater than 93% with an overall yield of 48% from FCS. The procedure was applicable for semi-preparative scale purification of BAFP.     

Preparation of Cibacron Blue F3GA Bonded Poly (styrenedivinylbenzene) (PSDVB) Microbeads Used for High Performance Affinity Chromatography

Recentlyhighperformanceliquidaffinitychr0mat0graphy(HPLAC)hasdevel0pedveryquickly.HPLACcombinesthespeedandres0lvingp0werofHPLCwithbiol0gicalspecificityofaffinitychromatographyandhasbeenwidelyusedasananalyticalt00linbiochemicalresearch.CibacronBIueF3GAisthem0stwideIyusedreactivetriazine-baseddyewhichhasspecificinteracti0nwithpyridinenucleotide-dependentdehydr0genase,kinase,blo0dproteinsandotherpr0teinsandenzymes'.ltisasuitabIeHPLACligandbecauseofitsreactivityandchemicaIstability.Inthi…     

IMMOBILIZED CIBACRON BLUE F3G-A ON CROSSLINKED POLY (VINYL ALCOHOL) FOR AFFINITY CHROMATOGRAPHY

Immobilized triazine dye affinity chromatography has been widely used for protein purification. In this paper, cibacron Blue F3G-A was immobilized,through a spacer arm, onto a rigid hydrophilic porous polymer by reacting an epoxy-group-containing poly(vinyl alcohol) with 6-aminohexyl-N'-Cibacron Blue F3G-A,which was obtained by reacting Cibacron Blue F3G-A with excess of 1,6-diaminohexane, in a pH 8.6 buffer. The epoxy-group-containing poly(vinyl alcohol) was prepared by hydrolysis of macroporous crosslinded poly(vinyl acetate),which was synthesized by suspension copolymerization of vinyl acetate and triallyl isocyanurate in the presence of butyl acetate and n-heptane as diluents. The cibacron Blue F3G-A-immobilized poly(vinyl alcohol)was packed in a stainless steel column (250×5 mm I. D.) and the chromatographic behaviors of several proteins (cytochrome c, lysozyme, bovine serum albumin, insulin, and lactate dehydrogenase) were determined.     

制备型高效液相色谱法从积雪草提取物中分离纯化积雪草甙和羟基积雪草甙对照品

积雪草甙和羟基积雪草甙是积雪草及其相关制品质量控制的两个指标成分,本研究利用制备型高效液相色谱从积雪草提取物中同 时分离纯化得到这两个成分。对制备色谱的流动相组成、流速、进样量和检测波长等制备参数进行了优化。采用的色谱柱为C18柱(50 mm×200 mm,5 μm);流动相为甲醇-水(体积比为60∶40),流速100 mL/min;二极管阵列检测器在220 nm检测;进样体积为1.5 mL。在20 min的运行时间内,积雪草甙和羟基积雪草甙与干扰成分得到很好的分离,产品纯度达到98%以上。此方法具有快速高效、产品纯度高的 特点,可以用于制备积雪草甙和羟基积雪草甙对照品。     

Comparison of adsorption performances of metal–chelated polyamide hollow fibre membranes in lysozyme separation

Commercially available microporous polyamide hollow fibres are modified by acid hydrolysis to activate the reactive groups and subsequently binding of the ligand, i.e. Cibacron Blue F3GA. Then the Cibacron Blue F3GA-derived hollow fibres were loaded with different metal ions (i.e. Zn(II), Cu(II), Ni(II)) to form the metal chelate. The internal polymer matrix was characterised by scanning electron microscopy. The effects of pH, initial concentration of lysozyme, metal type and temperature on the adsorption of lysozyme to the metal–chelated hollow fibres were examined in a batch reactor. The non-specific adsorption of lysozyme onto the polyamide hollow fibres was 1.8 mg/g. Cibacron Blue F3GA immobilisation increased the lysozyme adsorption up to 62.3 mg/g. Metal–chelated hollow fibres showed a significant increase of the adsorption efficiency. Lysozyme adsorption capacities of Zn(II), Cu(II) and Ni(II)-chelated hollow fibres were different. The maximum capacities of Zn(II), Cu(II) or Ni(II)-chelated hollow fibres were 144.2, 75.2 and 68.6 mg/g, respectively. Significant amount of the adsorbed lysozyme (up to 97%) was eluted in 1 h in the elution medium containing 1.0 M NaSCN at pH 8.0 and 25 mM EDTA at pH 4.9. Repeated adsorption–desorption process showed that this novel metal–chelated polyamide hollow fibres are suitable for lysozyme adsorption.