含羧基嵌段的离聚体的合成及其性能研究

合成了羧基有序分布和羧基无序分布的两类光固化水性聚氨酯丙烯酸酯 (PUA)的离聚物 ,研究了其光固化反应动力学 ,并测定其预聚物分散液的性能和固化膜的性能。     

扩链剂对水性聚氨酯脲与聚甲基丙烯酸甲酯复合体系结构和性能的影响

分别用乙二胺 (EDA)和水作为扩链剂制备了聚氨酯脲 聚甲基丙烯酸甲酯 (PUA)水分散液 .借助DSC、DMA、FTIR研究了扩链剂对PUA的结构和性能的影响 .结果表明在EDA扩链体系中 ,虽然聚甲基丙烯酸甲酯 (PMMA)和聚酯软段以及扩链剂与异氰酸酯生成的硬段均有一定程度的相容性 ,但由此合成的PUA仍具有多相结构 ;水扩链体系只有一个较宽的二级转变区 ,各相之间有较大程度的混合 .由EDA扩链合成的PUA在耐溶剂、耐水性及拉伸强度等方面优于水扩链体系 .两种扩链剂体系所得PUA的性能差异 ,主要与二者和异氰酸酯反应生成的脲键密度不同 ,导致不同的微相结构有关     

氨乙基氨丙基聚二甲基硅氧烷改性水性聚酯型聚氨酯的研究

由聚酯二元醇、异佛尔酮二异氰酸酯和二羟甲基丙酸合成聚氨酯预聚体，以氨乙基氨丙基聚二甲基硅氧(AEAPS)为扩链剂，制备了AEAPS改性聚氨酯水分散液。与未改性的聚氨酯水分散液相比，AEAPS改性聚氨酯水分散液的粒径增大，但粒径分布和表面张力基本不变，说明疏水的聚二甲基硅氧烷侧链被包裹于分散颗粒的内部；此外，改性聚氨酯水分散液的冻融稳定性显著增强。AEAPS改性聚氨酯水分散液成膜后，吸水率明显下降，水在膜表面的接触角增加，400℃时热失重下降，具有良好的疏水性和耐热性。     

双马来酰亚胺树脂增韧研究（1）新型增韧剂的合成、表征及预聚物制备

合成了一种新的增韧剂双（６－稀丙基对甲酚）甲烷（ＭＢＡＰＣ），用元素分析（ＥＡ）、富里哀红外（ＦＴ－ＩＲ）、质谱（ＭＳ）、核磁共振（Ｈ－ＮＭＲ）等方法进行了表征。同时合成了二苯甲烷型双马来酰亚胺（ＭＤＡ－ＢＭＩ）。首次以ＭＢＡＰＣ增韧ＭＤＡ－ＢＭＩ并用溶液法制备了改性ＭＤＡ－ＢＭＩ预聚物。研究了该预聚物的热性能、溶解性和贮存稳定性。     

基于HEA封端聚氨酯大孔树脂颗粒的合成、表征及水声声学性能

制备了丙烯酸-β-羟乙酯（HEA）封端的聚氨酯（PUA）大分子单体,采用正庚烷作致孔剂,用悬浮聚合法合成了聚氨酯-苯乙烯（PUA-St）及聚氨酯-苯乙烯-甲基丙烯酸乙酯-二乙烯基苯（PUA-St-EMA-DVB）AB-交联共聚物大孔树脂颗粒。SEM表明：合成的PUA-St-EMA-DVB颗粒含有规整的、孔径较大的孔洞,...     

蒽醌型蓝色扩链剂及其PUA共聚物乳液的制备与性能

首先以1-甲氨基-4-溴-蒽醌和2-氨基-2-甲基-1,3-丙二醇为原料,通过取代反应合成了蒽醌型蓝色扩链剂1-(1,1-二(羟甲基))乙氨基-4-甲氨基蒽醌(HMEMAQ),并将其与N,N-二(2-羟乙基)丙烯酰胺作为扩链剂合成出聚氨酯预聚体,然后经与甲基丙烯酸甲酯和丙烯酸丁酯的接枝乳液共聚合制备出了性能稳定的共聚型蓝色聚氨酯-丙烯酸酯共聚物(PUA)乳液.然后用1H-NMR、FTIR、UV-Vis吸收光谱、粒度和电位分析、氙灯老化等方法对HMEMAQ的化学结构、PUA乳液及乳胶膜的性能进行了表征.研究发现,在N2气氛下,用偶氮类AIBN作为引发剂可以有效避免PUA乳液合成过程中生色基团的氧化变色现象.当AIBN用量达到不饱和单体的2 wt%时,接枝反应的单体转化率可达到99.9%.HMEMAQ用量对乳液的胶体性质和单体转化率没有明显影响.PUA聚合物和HMEMAQ的UV-Vis吸收光谱保持一致,最大吸收波长均为640.8 nm.与具有相同生色基团的共混型蓝色PUA乳胶膜相比,共聚型PUA乳胶膜的耐光色牢度和耐溶剂色牢度有明显的提高.     

鞋用水性聚氨酯胶黏剂的制备及表征

通过预聚体分散法,以二羟甲基丙酸(DMPA)、蔗糖(sucrose)为亲水扩链剂和交联剂制备了一种鞋用水性聚氨酯胶黏剂.通过FTIR、DSC、力学性能、固化速度等研究了蔗糖用量对聚氨酯结构与性能的影响.结果表明蔗糖己引入聚氨酯主链.随着蔗糖用量的增加,相同处理温度下聚氨酯胶液的固化速度提高,胶膜的吸水率降低,拉伸强度增大,断裂伸长率减小,粘接试样的T-剥离强度逐渐增大.当蔗糖用量超过5.52 wt%时,合成及乳化过程中体系容易凝聚,且所制得的胶黏剂粘接强度有所下降.总之,通过改变蔗糖用量可以显著改变水性聚氨酯结构与性能.     

紫外光固化水性油墨及墨膜耐磨性能

传统紫外光固化(UV)油墨具有粘度低、固化速度快、应用范围广等优点。 但存在使用少量有机溶剂、交联程度低等缺陷。 本文通过自由基聚合制备的苯乙烯丙烯酸共聚物与甲基丙烯酸羟乙酯(HEMA)反应制备水性预聚物。 通过甲基丙烯酸缩水甘油酯(GMA)和乙二胺反应制备了含有四丙烯酸官能团的活性稀释剂。 最后,通过水性预聚物、活性稀释剂、光引发剂以及少量溶剂制备了UV光固化水性油墨。 探讨了光引发剂的种类和质量分数、预聚物的相对分子质量和质量分数、活性稀释剂的结构和质量分数对UV油墨的光固化速度以及耐磨度的影响。 当预聚物的数均相对分子质量为1.98×10⁵且质量分数为30%、光引发剂质量分数为4%、活性稀释剂的官能团数目为4且质量分数为40%的UV水性油墨的光固化速率为1 s,经50次磨损质量损失为9%。 该方法所制得的UV水性油墨可用于柔版印刷、凹印、数字印刷等。     

水性丙烯酸酯聚氨酯涂料的研究

合成了含羟基的丙烯酸酯树脂,并与甲苯二异氰酸酯反应制备预聚体Ⅰ,Ⅰ与扩链剂二羟甲基丙酸反应得到含羧基的预聚体Ⅱ,最后用1,4-丁二醇交联,制得水性丙烯酸酯聚氨酯涂料,讨论了合成过程中影响乳液稳定性和涂膜性能的因素。测试结果表明：涂膜的强度、光泽、硬度等性能均优于传统的同类树脂。     

一类高折射率光固化有机硅树脂的性能研究

光固化有机硅材料兼具光固化的高效、能耗低和环保以及有机硅树脂优异的耐温、耐候性和电绝缘性能,因此,在LED等电子器件封装方面受到广泛关注.本文研究了自制的3种含丙烯酸酯基团的光固化苯基有机硅预聚物KDS-10、KMDS-03和KMS-03的光固化特性、光学性能和热稳定性能.结果表明,这些有机硅预聚物的折光指数随苯环含量的增加而增高,苯环含量从22.3%到37.7%,折光指数相应从1.496到1.542;3种预聚物与多种丙烯酸酯相容性好,用双官能的TPGDA作稀释剂,固化反应速率最快,丙烯酸酯基团的转化率也最高;光引发剂TPO引发的光固化反应速率和转化率均最高;高折射率有机硅预聚物KDS-10光固化后的薄膜具有优异的光学性能,在550 nm处的透过率为92.54%;玻璃化转变温度约为-17.41℃,起始分解温度为385℃.     

Comparative study between core-shell and interpenetrating network structure polyurethane/polyacrylate composite emulsions

Anionic aqueous polyurethane dispersion was prepared by using carboxyl acid group to make the polyurethane dispersible, and then nanograde core-shell and crosslinked IPN structure polyurethane/polyacrylate composite latex (PUA) were synthesized by soap-free emulsion polymerization method with polyurethane dispersion as seed. FTIR, DSC, dynamic light scattering, TEM, ESCA, TGA, electronic tensile machine were employed to investigate the structures and properties of the composite latex and their polymers. Meanwhile the core-shell composite PUA emulsion and the crosslinked IPN composite PUA emulsion were compared. The results showed that the particle morphology of PUA composite emulsion is inverted core-shell structure with polyacrylate as the core and with polyurethane as the shell. The morphology of the crosslinked PUA emulsion was multi-core structure. The surface in core-shell PUA contains rich PU phase. The phase structure of the crosslinked PUA is more uniform. Three transition temperatures are observed for the core-shell composite PUA, two transitions are observed for the film from the crosslinked PUA. The TGA curves of core-shell PUA and crosslinked PUA exhibit two stages, the first stage corresponds to the thermal decomposition of hard segments in seed polyurethane; the second stage corresponds to the decomposition of soft segments in PUA and decomposition of polyacrylate. With the increase of glycidyl methacrylate (GMA) amounts in PUA composite emulsions, the tensile strength of the PUA films as well as the average diameter of the PUA composite emulsion particles increase, the elongation at break of the PUA films decreases.     

MODIFIED ULTRAVIOLET-CURABLE WATER DISPERSIBLE POLYURETHANE-ACRYLATES*

Three kinds of UV-curable self-emulsified polyurethane-acrylate (PUA) prepolymer, i.e., conventional, chainextended and grafted PUAs, were prepared. The relatively small particle size of the PUA dispersions indicates that the PUAprepolymers exhibit sufficient aqueous dispersibility. The PUA prepolymers can substantially lower the interfacial tension ofwater. Chain-extended PUA dispersions exhibit pseudoplastic behavior and thixotropy to a greater extent than do theirconventional counterpart. The chain-extended and grafted PUA photocure to higher conversion than do the conventional PUequivalent. The results of DSC measurement suggest that there exists phase mixing between the hard and the soft segmentphases for the PUAs based on PEG 400 that is the comparatively short soft segment in the prepolymer. For the PUAprepolymers based on PEG having higher M_n values, chain-extending and grafting could impede the phase separationbetween the hard and the soft segment domains. The adhesion, impact strength and flexibility of the photocured films were tested.     

Surface composition and property of film prepared with aqueous dispersion of polyurethaneurea-acrylate including fluorinated block copolymer

The aqueous dispersion of polyurethaneurea-acrylate (PUA) including small amount of fluorinated block copolymers containing carboxyl groups (PATF), which can be dissolved in water, was used to make films and the surface properties of these films were examined. The experimental data show that the modified PUA film exhibits a hydrophobic surface property, although the original surface of PUA film is hydrophilic. The surface composition of the modified PUA film was measured by ATR and XPS. The results indicate that there is a concentration gradient of the fluorine groups along the lines of thickness of the modified film and towards the outmost surface layer, resulting from the migration of fluorinated blocks to the air side surface of the modified PUA film during the film formation process. However, the PUA film can not be modified effectively by adding the sodium salt of PATF, since the urethane groups in the system are easy to occupy on the surface of the film.     

Effect of the diisocyanate on the structure and properties of polyurethane acrylate prepolymers

In this study, we investigated the role of diisocyanate on the properties of polyurethane acrylate (PUA) prepolymers based on polypropylene oxide (M̄_n = 2000 g · mol⁻¹). The diisocyanates studied were isophorone diisocyanate, 4‐4′dicyclohexylmethane diisocyanate, and toluene diisocyanate (pure 2,4‐TDI, pure 2,6‐TDI, and a TDI mixture, TDI_tech). The molecular structure of the diisocyanate had a major role on the course of the polycondensation and, more precisely, on the sequence length distribution of the final prepolymer. Moreover, the structural organization of the prepolymer also strongly depended on the nature of the diisocyanate. Two types of behaviors were particularly emphasized. On the one hand, the PUA synthesized from 2,4‐TDI displayed an enhanced intermixing between soft polyether segments and hard urethane groups, as revealed by the analysis of hydrogen bonding in Fourier transform infrared. Consecutively, the glass transition shifted to higher temperatures for these polymers. On the other hand, strong hard–hard inter‐urethane associations were observed in 2,6‐TDI‐based prepolymers; these led to microphase segregation between polyether chains and urethane groups, as revealed by optical microscopy. This inhomogeneous structure was thought to be responsible for the unusual rheological behavior of these PUA prepolymers. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2750–2768, 2000     

Effect of polymerically‐modified clay structure on the morphology and properties of UV‐cured polyurethane acrylate/clay nanocomposites

Polyurethane acrylate (PUA)/clay nanocomposites were prepared by UV‐curing from a series of styrene‐based polymerically‐modified clays and PUA resin. Effect of the chemical structure of the polymeric surfactants on the morphology and tensile properties of nanocomposites has been explored. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) experimental results indicated that surfactants having hydroxyl or amino groups show better dispersion and some of the clay platelets were fully exfoliated. However, the composites formed from pristine clay and other polymerically‐modified clays without hydroxyl or amino groups typically contained both tactoids and intercalated structure. The mechanical properties of PUA composites were greatly improved where the organoclays dispersed well. Thermogravimetric analysis (TGA) and differential scanning calorimeter (DSC) were carried out to examine the thermal properties of the composites. The results showed that the loading of polymerically‐modified clays do not effect the thermal stability, but increased the Tgs of PUA/clay composites. Copyright © 2010 John Wiley & Sons, Ltd.     

聚氨酯脲-丙烯酸酯水分散液的粒径及形态研究

研究了羧基含量、异氰酸酯指数（［ － ＮＣＯ］／［ － ＯＨ］） 、聚氨酯脲与聚丙烯酸酯组成比（ＰＵＵ／ＰＡ） 以及一系列制备工艺因素对聚氨酯脲—丙烯酸酯（ＰＵＡ） 水分散液粒子尺寸及形态的影响。结果表明：羧基含量和ＰＵＵ／ＰＡ 组成比增大或异氰酸酯指数减小都会导致分散液粒径减小;ＰＵＡ 中ＰＡ 含量越大,ＰＵＡ 水分散液粒子形态越不规整;工艺因素如搅拌强度、升温速率等对ＰＵＡ 水分散液粒子尺寸及形态的影响不符合传统乳液聚合的规律。     

The effects of altered reaction conditions on the properties of anionic poly(urethane-urea) dispersions and films cast from the dispersions

Aqueous anionic polyurethane (PU) dispersions were synthesised from a polyester polyol, isophorone diisocyanate and α,α-dimethylol propionic acid using the prepolymer mixing process. Samples were neutralised by the addition of triethyl amine. The polymer chains were dispersed in water and extended with 1,2-ethylene diamine. The differences in the dispersion characteristics and the mechanical properties of the polymer films cast and dried from the dispersions caused by altered reaction conditions were determined.The reaction conditions proved to affect both the colloidal properties of the dispersions as well as the mechanical properties of the films. The neutralisation, the dispersion and the chain extension methods had all an influence on the average size of the formed PU particles. For the films, a change in the mechanical properties and probably in the amount of hard and soft domain separation was also observed. A good control over the properties was obtained by selecting the reaction parameters carefully. In particular, the dispersion method in which the prepolymer solution was added to water and not vice versa led to a considerably lower viscosity during the dispersion process. Thus a wider choice of raw materials was facilitated.     

聚甲基丙烯酸酯改性聚氨酯光固化水性体系研究

水性涂料;聚甲基丙烯酸酯改性聚氨酯光固化水性体系研究;接枝共聚物;聚氨酯丙烯酸酯;丙烯酸酯共聚物     

Synthesis of poly(urethane‐imide) using aromatic secondary amine‐blocked polyurethane prepolymer

A set of poly(urethane‐imide)s were prepared using blocked Polyurethane (PU) prepolymer and pyromellitic dianhydride (PMDA). The PU prepolymer was prepared by the reaction of polyether glycol and 2,4‐tolylene diisocyanate, and end capped with N‐methyl aniline. The PU prepolymer was reacted with PMDA until the evolution of carbon dioxide ceased. The effect of tertiary amine catalysts, organo tin catalysts, solvents, and reaction temperature were studied and compared with the poly(urethane‐imide) prepared using phenol‐blocked PU prepolymer. N‐methyl aniline blocked PU prepolymer gave a higher molecular weight poly(urethane‐imide) at a lower reaction temperature in a shorter time. Amine catalysts were found to be more efficient than organo tin catalysts. The reaction was favorable in particular with N‐ethylmorpholine and diazabicyclo(2.2.2)octane (DABCO) as catalysts, and dimethylpropylene urea as a reaction medium. The poly(urethane‐imide)s were characterized by FTIR, GPC, TGA, and DSC analyses. The molecular weight decreased with an increase in reaction temperature. The thermal stability of the PU was found to increase by the introduction of imide component. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4032–4037, 2000