壳聚糖的辐射效应的研究（Ⅱ）：辐射引起的某些化学变化

壳聚糖分子中的脱乙酰基单元比乙酰化单元更易被高能辐射破坏。红外光谱的研究结果表明,羟基基团的吸收强度随辐射强度的增加而增加,胺基和醚键的吸收强度则下降。壳聚糖辐照后并未发现有羰基形成。壳聚糖在辐照作用下除了胺基的变化外,主要通过苷键的断裂降解。     

高效液相色谱峰压缩中灵敏度增加值与峰压缩因子的关系研究

以从塔板理论得到的色谱流出曲线为基础,推导了高效液相色谱(HPLC)双流动相分离场中实现峰压缩时,峰压缩因子(峰压缩后的半峰宽与未进行峰压缩时的半峰宽的比值)和峰高表示的灵敏度变化(峰压缩后的峰高与未进行峰压缩时的峰高的比值)的关系,结果表明峰高表示的灵敏度增加值等于峰压缩因子的倒数.并用色氨酸、香豆素、苯和2-硝基酚在不同速率差实现堆积时的相关参数进行了验证.实验结果表明,这些化合物在各个峰压缩条件下的峰压缩因子倒数和实际灵敏度增加值相等,实验结果与理论推导结果一致.考察了该关系式在实际样品测定中的应用,结果表明灵敏度增加值等于峰压缩因子的倒数,这也与理论部分的结果一致.     

铈掺杂高密度硼硅酸盐玻璃光谱性质研究

实验制备了一种密度为5.2 g.cm-3的高密度铈离子掺杂硼硅酸盐闪烁玻璃,该玻璃具有较高的析晶稳定性。测试了该闪烁玻璃的激发和发射光谱,其峰值波长分别对应于325和385 nm,斯托克斯位移为60 nm。当氧化铈掺杂浓度小于1%(质量分数)时,325 nm激发下的发射光谱强度随浓度的增加而提高,而掺杂浓度的进一步提高,由于三价态铈离子的自吸收等吸收猝灭效应导致380 nm的发射强度出现严重降低。掺杂1%(质量分数)的玻璃样品经245Gy的伽马射线辐照后,其可见波段的透过率并未出现明显降低,说明该玻璃具有较好的耐辐照性能。     

三磷酸铝的傅里叶变换红外光谱分析

提出了应用傅里叶变换红外光谱法,在由生产中产生的偏磷酸铝和磷酸二氢铝杂质存在下测定三磷酸铝(AlH2P3O10.2H2O)。从红外吸收光谱可见,三磷酸铝(Al-TP)及偏磷酸铝(Al-MP)分别在波数为986 cm-1及740 cm-1处存在特征吸收峰,而磷酸二氢铝在此波段无吸收峰。据此提出,用Al-MP作内标,以Al-TP与Al-MP的峰高比值与两者相应的浓度比值图,并采用曲线拟合或最低基线计算法制得工作曲线。由此可求得试样中Al-TP与Al-MP的含量比值。由于采用了Al-MP作内标,其干扰也得到消除。同时用标准(浙B/HG 204-88及GB/T 1714-1979)中所述方法对样品中磷酸二氢铝及水分的含量分别予以测定。按文中所给的公式,计算样品中三磷酸铝的含量。     

聚丙烯酰胺-g-聚苯胺的导电水凝胶的制备及性能研究

通过两步聚合得到既具有良好力学强度又具有优良导电性能的聚丙烯酰胺-g-聚苯胺复合水凝胶.首先,丙烯酰胺和N-(4-氨苯基)丙烯酰胺在钴源γ-射线辐照下共聚形成聚丙烯酰胺水凝胶;然后,苯胺在具有微观多孔结构的聚丙烯酰胺凝胶中吸附,在过硫酸铵的作用下与凝胶的苯胺侧基发生接枝聚合,得到聚丙烯酰胺-g-聚苯胺水凝胶,并形成聚苯胺连续导电通道.改变辐照时间和辐照剂量率,所获得的聚丙烯酰胺水凝胶的凝胶分数随着辐照剂量的增加逐渐增大,而溶胀率随着辐照剂量的增加呈先增后减的趋势,表明凝胶的交联程度随辐照剂量呈规律性变化;辐照交联聚合的单体浓度对凝胶的性能,如溶胀率、微观结构和机械性能等也有影响.酸掺杂后,聚丙烯酰胺-g-聚苯胺复合凝胶的电导率达到9 S/m.     

γ射线辐照对含钆有机玻璃性能的影响EI北大核心CSCD

以^(60)Co作为γ射线源,对不同Gd元素含量的含钆有机玻璃进行不同剂量的γ射线辐照。通过可见光吸收光谱仪、万能试验机、热重分析仪和电子顺磁共振波谱仪等仪器测定含钆有机玻璃在γ射线辐照前后的光学性能、力学性能、热性能和自由基的变化。结果表明,随着γ射线辐照剂量的增加,含钆有机玻璃发生辐照降解,产生大量自由基,导致材料发生变色发黄现象,冲击强度、弯曲强度以及热稳定性能均有下降的趋势。且Gd元素含量越高,辐照降解程度越大。     

石墨炉原子吸收光谱中海水的背景吸收研究

由于海水的成分复杂,含盐量高,给用石墨炉直接测定其中的痕量杂质带来许多困难^[1]。Sturgeon等用预先分离的方法来克服干扰^[2]。为了进行直接测定,研究海水背景吸收的来源、特点和消除方法是重要的。海水背景吸收的波长特性和在石墨管内蒸发行为的研究表明,海水的背景吸收主要来自氯化钠。时间特性的研究表明,背景吸收的时间分布及背景峰高与原子化阶段的加热方式和原子化温度有关。作者还研究了基体改进。剂和其它减小背景吸收的方法。     

电子自旋共振准三维图象的重建方法

根据投影切片原理, 设计了一个简单而有效的ESR图象重建算法和程序, 可利用样品的一集ESR谱, 方便地绘制出样品在某截面的自旋密度立体轮廓图、等值图和散点密度分布图等, 为分析和研究自旋密度的分布及其性质, 提供了直观依据。作为应用, 文中给出了石英杜瓦受紫外光辐照后产生的局部晶格缺陷——F心的空间分布图, 图中清楚表明, F心的浓度与辐照方向和辐照强度的密切关系, 与试验结果完全相符。     

聚四氟乙烯辐射接枝苯乙烯-丙烯酸的研究

本文采用共辐照工艺,在20°—40℃范围内研究了聚四氟乙烯辐射引发接枝苯乙烯-丙烯酸的动力学。找到了接枝温度与临界辐照强度的关系。高于临界辐照强度,接枝发生在表面,反之,接枝发生在整体。借光学显微镜和扫描电子显微镜研究了接枝膜的断面和表面结构。表面接枝膜的接枝量约1毫克/厘米~2,平均粘结强度高达100公斤/厘米~2以上。表面接枝膜的电性能与未接枝的聚四氟乙烯相仿。可知聚四氟乙烯表面辐射接枝苯乙烯-丙烯酸可用作强粘结强度的结构材料或电子元件的粘结密封材料。     

反气相色谱研究氯化聚乙烯共混物的相容性

本工作首先肯定了IGC是测定高聚物各种转变和其它结构变化的可靠方法,并对它的制样方法和实验技术做了适当的改进,发现峰高图与高聚物内部结构变化有关。据此,提出用峰高图来表示IGC的测定结果。     

Quantitative Characterization of the Molecular Absorption Spectra in the Ultraviolet Region by Gas Chromatography

The aim of this study was to obtain quantitative characteristics of the ultraviolet absorption spectra as the molecular absorptivity at the wavelength of maximum absorbance. Organic as well as inorganic compounds were explored. A gas chromatography—ultraviolet absorption instrument has been used in the quantitative study of molecular ultraviolet absorption spectra in the vapour phase. The wavelength range studied was between 168 and 330?nm. The absorbance of 170 compounds was determined relative to perchloroethylene and their molecular absorptivities were calculated. For various groups of compounds, these relative absorptivities varied within two to three orders of magnitude. Standard curves were linear within four orders of magnitude from limit of quantification up to an absorption value of 1.5 absorbance units. The noise level was 3?×?10^?5 absorbance units peak to peak at a bandwidth of 1.7?nm and a wavelength range from 180 to 330?nm was preferred. The detection limit for mesitylene was calculated to be 2 pg/s and for naphthalene 1 pg/s with 4?s store cycle time.     

Curing kinetics of the epoxy system diglycidyl ether of bisphenol A/isophoronediamine by Fourier transform infrared spectroscopy

The curing reaction of an epoxy system consisting of a diglycidyl ether of bisphenol A (BADGE, n = 0) and isophoronediamine (IPD), was studied by Fourier transform infrared spectroscopy (FTIR). The degree of conversions and the reaction rates at different isothermal curing temperatures were calculated from the infrared spectra using a method derived from Beer's law. This method is based on the ratio of the height of the characteristic absorbance peak to reference absorbance peak. A kinetic model proposed by Sourour and Kamal has been used to fit experimental data. Copyright © 2008 John Wiley & Sons, Ltd.     

ATR-FTIR技术用于酒精饮品中乙醇含量的快速测定

建立了快速测定酒精饮品中乙醇含量的衰减全反射-傅立叶变换红外光谱(ATR-FTIR)法.以ZnSe槽形板为ATR晶体,以水为背景采集样品的FTIR图.以1045 cm-1的C-OH伸缩振动为特征峰,用部分峰面积表示整个吸光度以消除肩峰干扰,分别建立了低浓度区(0～24%(V/V))和高浓度区(24%～84%(V/V))两条标准曲线,其线性相关系数均大于0.999,乙醇水溶液的检测限为0.20%.对啤酒、干红葡萄酒以及白酒的分析表明,该方法准确、快速、方便,适用于酒精饮品中乙醇含量的快速测定.     

ZSM-5沸石上Brönsted酸的红外光谱测定法及改性ZSM-5沸石的表面酸性研究

研究各种 ZSM-5沸石样品的红外光谱发现: 在1875和2000 cm~(-1)附近有两个强红外吸收谱带, 两个谱带吸光度的比值是个特征值。本文提出了以2000 cm~(-1)谱带为“内标”, 用相对吸光度的办法处理ZSM-5沸石的红外光谱, 测定了各种改性ZSM-5样品的Brönsted酸, 并同电位滴定法所测得的Brönsted 酸浓度和异丙苯裂解活性分别关联, 都有较好的对应关系。文中以实验为依据讨论了1875和2000 cm~(-1)谱带的归属, 并根据Beer-Lambert定律, 推导出了相对吸光度与浓度的关系, 从而确立了ZSM-5沸石上红外光谱定量处理方法的理论基础。     

Quantitative analysis of X-ray absorption spectra using a 2D map representation

A promising possibility for the quantitative analysis of X-ray absorption near edge structure (XANES) spectra of nanosized electrode materials is demonstrated. We used a 2D map representation technique, which utilizes the values of the first derivatives of the absorbance with respect to the inserted Li(+) content plotted over the two-dimensional space defined by the inserted Li(+) content (mole) versus photon energy (eV) as a single map. The technique was applied to XANES spectra of the Li(y)CoO system in the first Li(+) insertion reaction for determining the structural and electronic variations associated with the change in Li(+) content. The obtained show that the intensities of two peaks at 7725 and 7711 eV increased with the Li(+) content and the difference of intensity change of these two peaks carried out for successive couples of spectra yielded the largest changes at 1.05 and 1.98 mol of Li content. This approach for quantitative analysis of XANES without using conventional simulation techniques enable us to interpret X-ray absorption spectroscopy (XAS) as a quantitative analytical technique with greater confidence.     

STUDIES ON THE PROTEIN CONFORMATION OF PHYTOCHROME

Abstract— The extinction coefficients for large rye phytochrome were found to be: Fluorescence and circular dichroism spectra of large- and small-molecular-weight rye phytochrome give no evidence for a protein conformational change on phototransformation of phytochrome. The large molecule has a fluorescence emission peak at 331 nm when excited at 290 nm, and an excitation peak for this emission at 288 nm. The circular dichroism spectra indicate that large rye phytochrome has about 17–20% a-helix content, 30%β-structure and 50% random coil, and that the small rye phytochrome has about 10–13%α-helix content. The ultraviolet difference spectra for large and small rye phytochrome are similar and differ from the difference spectrum of the small oat phytochrome in the relative size of the 296–298 nm peak. The difference spectra may reflect changes in chromophore absorbance and in the environment of amino acid residues near the chromophore, particularly of tyrosine, and perhaps of tryptophan and cysteine.     

Univariate method for background correction in liquid chromatography-Fourier transform infrared spectrometry

An univariate method is proposed for background correction in on-line gradient liquid chromatography-Fourier transform infrared (LC-FTIR) spectrometry using acetonitrile:water as mobile phase components. The method is based on the calculation of the ratio of absorbances (AR) at two characteristic wavenumbers for each spectrum. This parameter is subsequently used to locate the most appropriated eluent spectrum within a reference spectra matrix (RSM) to be subtracted from each spectrum included in the sample chromatogram. To correct minor changes in eluent spectra intensity during the elution of analytes, a correction factor (Kf), defined as the ratio of the absorbance of the sample and the selected eluent spectrum at a defined wavenumber was determined. The performance of the procedure was evaluated by correcting an on-line gradient LC-FTIR injection of a mixture of two pesticides (Atrazine and Diuron). Using the AR of the absorbance at 2248.6 and 2256.3 cm(-1) and a Kf at 2248.6 cm(-1), the correlation factors between FTIR spectra extracted at the peak apex from the LC-FTIR chromatogram and those obtained from pure pesticide standards were 0.975 and 0.94 for Atrazine and Diuron, respectively.     

First-derivative solid-phase spectrophotometric determination of molybdenum at the ng ml(-1) level

Derivative spectrophotometry was applied to solid-phase spectrophotometry in order to enhance its sensitivity and remove the large background noise caused by the absorption of the resin layer itself, and avoid the necessity of preparing a blank. The determination of micro-amounts of molybdenum (at the ng ml(-1) level) with pyrocatechol violet to form a 11 blue complex in acid medium, which is fixed on a dextran-type anion-exchange resin (Sephadex QAE-A-25), is described as an example of the application of this technique. The absorbance of the resin, packed in a 1 mm spectrophotometric cell, was measured directly. The characteristic peak amplitude of the signal at 716 nm in the first-derivative spectra is useful for quantitative determination of molybdenum (2-8 ng ml(-1); RSD = 4, 30%) in natural and industrial water samples, plant tissues and soil extracts.     

Vibrational spectroscopic investigation of stereoregularity effects on syndiotactic polypropylene structure and morphology

Vibrational spectroscopy is used to sensitively detect specific morphologies and microstructures present in metallocene-catalyzed syndiotactic polypropylenes (sPP). Six materials, ranging in racemic triad content from 26 to 96% rr, are studied. Changes in high-resolution infrared (IR) and Raman spectra of melt-slow-cooled films are observed as the degree of syndiotacticity varies. Three different types of peak behavior are observed: splitting, wavenumber shift, and change in peak intensity. An overall trend toward greater molecular order (e.g. ordered chain conformations, increased crystallinity) is observed as syndiotacticity increases. By combining results with supporting evidence from X-ray diffraction and IR linear dichroism experiments of highly syndiotactic sPP, new peak assignments are proposed for tacticity-sensitive vibrational bands. Some very interesting spectral behavior is observed for material of intermediate stereoregularity (49% rr). Previously unobserved peaks appear in X-ray diffractograms and IR absorbance spectra, suggesting the presence of an as-yet unidentified “transitional” structure—perhaps a disordered modification of crystalline Form I. This moderate level of syndiotacticty appears to be a critical point or threshold below which sPP chains are unable to adopt characteristic helical or planar zigzag conformations. Results from this work provide a more thorough understanding of stereochemical effects on vibrational spectra, which will be very useful in the interpretation of ongoing IR linear dichroism studies of newly available semi-syndiotactic (semi-sPP) materials.     

磁场作用下葡萄糖近红外光谱检测技术研究

采用傅立叶变换红外光谱仪(FTIR)研究了磁场强度对葡萄糖溶液近红外光谱的影响,发现磁场作用下葡萄糖的近红外光谱吸收强度和部分峰位发生显著变化。分析了磁场对葡萄糖溶液近红外光谱吸收的影响机理。采用偏最小二乘回归法(PLS)建立了磁场作用下葡萄糖溶液的定量分析模型,使用验证集进行验证。研究结果表明,磁场对葡萄糖分子基团偶极矩产生诱导作用,使偶极矩增大,吸收增强;同时磁场作用下,葡萄糖分子趋于沿平行于磁场的方向排列,其基团振动频率(特征吸收峰)吸光度与浓度变化的线性关系得到极大的改善。该研究有助于提高葡萄糖分子吸收强度及其测量精度,为进一步提高血糖检测精度提供技术支持。