悬浮-乳液复合聚合聚苯乙烯-聚甲基丙烯酸甲酯复合粒子的颗粒特性和成粒机理

采用在苯乙烯 (St)悬浮聚合过程中滴加甲基丙烯酸甲酯 (MMA)乳液聚合组分的悬浮 乳液复合聚合方法 ,制备大粒径聚苯乙烯 聚甲基丙烯酸甲酯 (PS PMMA)复合粒子 .研究聚合物粒径分布和颗粒形态的变化发现 ,在St悬浮反应中期滴加MMA乳液聚合组分后 ,聚合体系逐渐由悬浮粒子与乳胶粒子并存向形成单峰分布复合粒子转变 ,最终形成核 壳结构完整的大粒径PS PMMA复合粒子 ;在St悬浮反应初期滴加MMA乳液聚合组分 ,St与MMA一起分散成更小液滴 ,反应后期凝并成非核 壳结构复合粒子 ;在St悬浮反应后期滴加MMA乳液聚合组分 ,PMMA乳胶粒子与PS悬浮粒子基本独立存在 .根据以上结果 ,提出了St MMA悬浮 乳液复合聚合的成粒机理 .     

聚甲基丙烯酸甲酯/聚甲基丙烯酸-2-羟乙酯复合微球的合成及药物吸放性能

采用在甲基丙烯酸甲酯（MMA）悬浮聚合过程中滴加甲基丙烯酸-2-羟乙酯（HEMA）乳液聚合组分的悬浮-乳液耦合聚合方法,制备了大粒径聚甲基丙烯酸甲酯／聚甲基丙烯酸-2-羟乙酯（PMMA／PHEMA）复合微球。PMMA／PHEMA复合微球表面以HEMA乳液聚合物为主,且具有微孔结构。PMMA／PHEMA复合微球在水和苄醇中的平衡溶胀率大于PMMA微球。PMMA／PHEMA复合微球48h异丁苯丙酸负载百分比为35．6％,PMMA为27．6％。在磷酸盐缓冲液中释放时间达到360h,释放量占负载总量的82％;而PMMA微球的释放时间为216h,释放量仅占负载总量的60％。     

复合微乳液聚合制备P(MMA-UA)纳米乳胶粒子的研究

将聚氨酯预聚体可聚合乳化剂 (APUA)和甲基丙烯酸甲酯 (MMA)的复合微乳液体系 ,分别用水溶性过硫酸钾 (K2 S2 O8)和油溶性偶氮二异丁腈 (AIBN)作引发剂 ,进行微乳液聚合研究 ,制备了P(MMA UA)复合纳米乳胶粒子 .研究了APUA用量、聚合温度对聚合动力学的影响 ;用透射电子显微镜 (TEM)观察了不同乳化剂浓度及引发剂体系对胶粒形态、大小及分布的影响 .结果表明 ,用可聚合乳化剂APUA可制得稳定性很好的P(MMA UA)纳米级核 壳型乳胶粒子 ,乳胶粒径在 5 0nm左右 .随着乳化剂用量增加 ,粒子变小 ;不同类型的引发剂对胶乳的性质有较大影响 ,以APUA为乳化剂 ,K2 S2 O8为引发剂 ,在聚合反应过程中或在聚合反应后的放置中 ,会出现P(MMA UA)的纳米水凝胶 (Nanogel)现象 .     

氧化-还原低温引发甲基丙烯酸甲酯/丙烯酸丁酯超浓乳液聚合研究

以乳化剂十二烷基硫酸钠 (SDS)和共乳化剂十六烷醇 (HD)作为复合乳化体系 ,过氧化二苯甲酰(BPO)和N ,N 二甲基苯胺 (DMA)作为氧化还原引发体系 ,甲基丙烯酸甲酯 丙烯酸丁酯 (MMA BA)作为混合单体 ,制备了分散相占 83 %以上的稳定的超浓乳液 ,然后在低温下引发聚合 .探讨了引发剂浓度、氧化剂与还原剂的摩尔比、乳化剂的浓度、液膜增强剂的种类、聚合温度等因素对聚合稳定性和聚合速率的影响 ,测定并计算得到了聚合速率的公式 ;用激光散射粒度分布仪测定了聚合物乳胶粒子的大小及粒径分布 ,用透射电子显微镜观察了聚合物乳胶粒的形态 ,讨论了乳化剂浓度、聚合温度等对乳胶粒形态、大小的影响     

无皂乳液聚合法制备P(St-MMA-SPMAP)单分散乳胶颗粒

利用无皂乳液聚合 ,分别用一步法和两步法合成了单分散的聚 (苯乙烯 甲基丙烯酸甲酯 甲基丙烯酸丙基磺酸钾 ) (P(St MMA SPMAP) )乳胶颗粒 .在该聚合体系中 ,当水溶性磺酸基单体SPMAP的浓度小于 17mmol L时 ,为均相成核过程 ,能制备单分散的乳胶颗粒 .其中 ,用两步法制备的乳胶颗粒相互之间无粘连 .此外 ,还对一步法合成苯乙烯 甲基丙烯酸甲酯 甲基丙烯酸辛基磺酸钠 (P(St MMA SOMAS) )乳胶颗粒进行了初步研究 .     

反相微乳液模板原位聚合制备纳米氯化银/聚甲基丙烯酸甲酯及其结构表征

用甲基丙烯酸甲酯(MMA)作油相,反相胶束微乳液作为模板,制备了纳米氯化银(AgCl)粒子,再进行原位聚合制备了纳米氯化银/聚甲基丙烯酸甲酯(AgCl/PMMA)复合材料.透射电镜(TEM)分析表明,纳米AgCl的尺寸为20～80 nm.扫描电镜(SEM)测试表明纳米AgCl粒子均匀地存在于PMMA基材中.红外分析证明,胶束中水和表面活性剂AOT的羰基在MMA聚合后微观环境发生变化,纳米粒子同聚合物之间有吸附行为.动态力学(DMTA)分析复合材料,发现纳米AgCl粒子与聚合物之间存在强烈相互作用,形成了中间相层(interphase layer),改变了聚合物的动态力学性能.     

丙酮对MMA-St无皂乳液聚合速率的影响

运用溶剂热法,以丙酮-水为分散介质,过硫酸钾为引发剂引发甲基丙烯酸甲酯(MMA)和苯乙烯(St)共聚,制备了P(MMA-St)。讨论了丙酮含量对MMA,St均聚和MMA-St共聚的影响。实验结果表明：随着丙酮含量的增加,MMA成核速率先减小后增大,聚合速率先减小后增大再减小;St成核速率先增大后减小再增大,聚合速率先增大后减小;丙酮含量对MMA-St共聚的聚合速率的影响与单体比例有关,当V(MMA)：V(St)=1：1时,聚合速率随丙酮的增加逐渐降低,当V(MMA)：V(St)=1：3和3：1时,聚合速率随丙酮的增加先增大后逐渐减小;当丙酮含量高于40％后,MMA,St各自均聚和共聚的反应速率均明显减小。     

新型乳液聚合制备疏松PMMA树脂及成粒机理

采用以水相为分散相、甲基丙烯酸甲酯 (MMA) 环己烷混合物为连续相的新型乳液聚合制备PMMA树脂 .发现 ,在未加乳化剂和加入少量Tween2 0乳化剂时 ,均可制备由初级粒子凝聚而成、无明显皮膜结构的疏松PMMA粒子 ,初级粒子粒径小于环己烷存在下MMA悬浮聚合得到的PMMA粒子的初级粒子 .根据聚合体系相构成、PMMA在MMA 环己烷混合液的溶解性及PMMA粒子粒径分布和形态的演变 ,提出了在分散水滴内乳液聚合形成初级粒子 生长 凝聚的新型乳液聚合成粒机理     

甲基丙烯酸甲酯自由基聚合歧化终止机理

首先用过氧化二苯甲酰(BPO)引发甲基丙烯酸甲酯(MMA)自由基聚合合成聚甲基丙烯酸甲酯(PMMA),然后用偶氮二异丁腈(AIBN)为引发剂,研究PMMA中由歧化终止生成的末端双键与苯乙烯(St)的共聚合反应行为。采用体积排除色谱(SEC)、核磁共振波谱(NMR)对聚合物进行了分析表征。结果表明：与单体MMA相似,PMMA在化学位移δ=6.20和5.47处有对应于聚合物末端双键氢的NMR信号。远程异核和近程异核相关NMR,¹³C-NMR和DEPT-135 NMR分析和自由基共聚合实验确证：MMA自由基聚合的双基歧化终止为单一的链自由基末端β位甲基氢自由基转移机理,生成1,1-二取代甲基丙烯酸酯型双键。除双基歧化终止反应外,体系还明显地存在苯甲酰初级自由基和苯初级自由基与链自由基间的初级终止反应。     

苯乙烯与甲基丙烯酸甲酯在聚乙二醇水溶液中无皂乳液共聚的粒径变化

利用高倍光学显微镜、库尔特粒径测试仪、TEM及zeta电位跟踪观测了苯乙烯(St)与甲基丙烯酸甲酯(MMA)在聚乙二醇(PEG)水溶液无皂乳液共聚过程中的粒径、粒径分布以及zeta电位变化.聚合物粒径会经历由小到大(某些粒径甚至超过1000μm,分布在0.04～2000μm的极宽范围内),再由大变小(形成的数均分布在0.04～0.18μm)过程,且粒径分布也由宽变窄,最终粒径数均分布集中在0.04～0.18μm窄范围内.结合聚合转化率数据,根据PEG水溶液中进行的St/MMA无皂乳液共聚粒径变化过程,以及zeta电位在聚合过程中异于普通无皂乳液的现象,认为该体系在反应初期形成的粒子会形成粒子堆,并随着聚合反应的继续,带有离子片段的自由基链段不断扩散进入粒子堆表面的小粒子,使其zeta电位不断增强,最终脱离粒子堆.提出了PEG水溶液中St/MMA无皂乳液共聚聚并脱析成核机理.     

The characterization of latex particles prepared by pulsed electron beam induced emulsion polymerization

The emulsion polymerization of styrene (St) and methyl methacrylate (MMA) induced by 10 MeV pulsed electron beams (PEB) was investigated. The monomer conversion of MMA and St was found to be very low so that the final prepared poly(methyl methacrylate) (P(MMA)) and polystyrene (PS) latex particles exhibit porous structures, as verified by TEM and SEM observations. The results of dynamic light scattering (DLS) and gel permeation chromatography (GPC) showed that both the particle size and the molecular weight of PS and PMMA latexes decrease with the increase of the absorbed dose. However, the molecular weights and the particle sizes of the PS and PMMA latexes change differently with the irradiation time. This work indicated that emulsion polymerization induced by high energy electron beam has an advantage over that induced by γ-ray or chemical initiators in the preparation of latex with a low molecular weight and porous structure.     

甲基丙烯酸甲酯/纳米SiO_2粒子分散液的细乳化和细乳液聚合

对包含纳米SiO2粒子的甲基丙烯酸甲酯(MMA)的细乳化和细乳液聚合行为进行了研究.发现在超声细乳化过程中,90%以上的分散于MMA相的纳米SiO2粒子将从油相逃逸到水相.采用甲基丙烯酸3-(三甲氧基甲硅烷基)丙酯(MPS)偶联剂处理SiO2粒子,可以增加其表面亲油性,抑止这种逃逸,经测定几乎全部SiO2粒子在超声细乳化后仍稳定停留在细乳化亚微液滴中.通过进一步细乳液聚合,得到了分散稳定、界面清晰的包裹有纳米SiO2粒子的聚甲基丙烯酸甲酯复合粒子乳液.     

种子乳液聚合法制备多孔乳胶粒

用批量乳液聚合法制备了苯乙烯（Ｓｔ）———甲基丙烯酸甲酯（ＭＭＡ）二元共聚种子乳液Ｓ１以及Ｓｔ ＭＭＡ 丙烯酸（ＡＡ）三元共聚种子乳液Ｓ２,通过连续法无皂种子乳液聚合合成了一系列不同ＡＡ或ＭＡＡ（甲基丙烯酸）含量的Ｓｔ、ＭＭＡ三元共聚乳液．将所得复合胶乳进行碱／酸分步处理,得到具有多孔结构的乳胶粒．用透射电镜对胶粒形态进行了表征,考察了不饱和酸种类和用量、碱处理初始ｐＨ值及溶胀剂对胶粒成孔的影响．     

The suspension�Cemulsion combined polymerization of fluorinated acrylic monomer and the fluorinated latex film surface properties

The perfluoroacrylate-containing copolymer composite particles were fabricated by suspension?Cemulsion combined polymerization (SECP). The features and formation mechanism of resulting polymer particles in SECP were studied. The fluorinated latexes with better stability and those fluorinated films with high surface fluorine content were prepared by SECP using fluorine-free surfactants as an emulsifying agent, and the surface natures of the fluorinated films were characterized. It was found that P(MMA?CBA) latex particles gradually coagulated with P(PFA?CBA) particles after adding emulsion polymerization constituents at the midstage of the suspension polymerization, and fluorinated composite particles with core?Cshell structure and larger size were obtained. The fluorine contents either on the film surface or in the bulk of the film and the films from SECP are higher than those from miniemulsion polymerization at high PFA feed ratio (more than 20?wt.%). The model of PFA?CMMA?CBA SECP was proposed according to the variations of particle features of the composite particles.     

Synthesis of nano-ZnO/poly(methyl methacrylate) composite microsphere through emulsion polymerization and its UV-shielding property

Nano-ZnO/poly(methyl methacrylate)(PMMA) composite latex microspheres were synthesized by in-site emulsion polymerization. The interfacial compatibility between nano-ZnO particles and PMMA were improved by treating the surface of nano-ZnO particles hydrophobically using methacryloxypropyltrimethoxysilane (MPTMS). TEM indicated that nano-ZnO particles present in nanosphere and have been encapsulated in the PMMA phase. FT-IR confirmed that MPTMS reacted with the nano-ZnO particle and copolymerized with MMA. It was clearly found from SEM that ZnO nanoparticles can be homogeneously dispersed in the PVC matrix. The absorbance spectrum of the nanocomposite polymer suggested that increasing the amount of nano-ZnO in composite particles could enhance the UV-shielding properties of the polymers. The nano-ZnO/PMMA composite particle could eliminate aggregation of ZnO nanoparticle and improve its compatibility with organic polymer. This means that the composite particles can be widely applied in lots of fields.     

The morphology of composite polymer particles produced by multistage soapless seeded emulsion polymerization

 Composite polymer particles which contain poly(methyl methacrylate) (PMMA) and polystyrene (PS) components (PMMA/PS composite particle) were synthesized by the method of multistage soapless seeded emulsion polymerization. In this study, the process of multistage soapless seeded emulsion polymerization included two-stage polymerization, three-stage polymerization or four-stage polymerization. The morphologies of the PMMA/PS composite particles were studied. The kinetic factor was the main force to control the morphology of the linear PMMA–PS composite particles which were synthesized by the method of two-stage reaction. Both the kinetic factor and the thermodynamic factor decide the morphology of the linear composite particles which were synthesized by the method of either three-stage or four-stage reaction. However, the thermodynamic factor cannot influence the morphology of the PMMA/PS composite particles with a cross-linked structure which were synthesized by the method of three-stage reaction. The cross-linked composite polymer particles had the morphology of a multilayer structure, which showed that the polymer layers accumulated in their order of production. Received: 9 January 2001 Accepted: 14 June 2001     

Preparation and clinical application of immunomagnetic latex

Magnetic poly(methyl methacrylate) (PMMA)/poly(methyl methacrylate‐co‐methacrylic acid) [P(MMA–MAA)] composite polymer latices were synthesized by two‐stage soapless emulsion polymerization in the presence of magnetite (Fe₃O₄) ferrofluids. Different types and concentrations of fatty acids were reacted with the Fe₃O₄ particles, which were prepared by the coprecipitation of Fe(II) and Fe(III) salts to obtain stable Fe₃O₄ ferrofluids. The Fe₃O₄/polymer particles were monodisperse, and the composite polymer particle size was approximately 100 nm. The morphology of the magnetic composite polymer latex particles was a core–shell structure. The core was PMMA encapsulating Fe₃O₄ particles, and the shell was the P(MMA–MAA) copolymer. The carboxylic acid functional groups (COOH) of methacrylic acid (MAA) were mostly distributed on the surface of the composite polymer latex particles. Antibodies (anti‐human immunoglobulin G) were then chemically bound with COOH groups onto the surface of the magnetic core–shell composite latices through the medium of carbodiimide to form the antibody‐coated magnetic latices (magnetic immunolatices). The MAA shell composition of the composite latex could be adjusted to control the number of COOH groups and thus the number of antibody molecules on the magnetic composite latex particles. With a magnetic sorting device, the magnetic immunolatices derived from the magnetic PMMA/P(MMA–MAA) core–shell composite polymer latex performed well in cell‐separation experiments based on the antigen–antibody reaction. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1342–1356, 2005