NiO/Al_2O_3催化剂上二氧化碳气氛下异丁烷耦合脱氢制异丁烯

研究了二氧化碳气氛下NiO/Al2O3催化剂上异丁烷脱氢制异丁烯的反应性能,考察了助剂K2O对NiO/Al2O3催化性能的影响。结果表明,与在惰性气氛下的反应相比,在二氧化碳气氛下异丁烷脱氢与逆水煤气变换反应耦合,促进了异丁烷脱氢反应,异丁烯的收率得到提高。助剂K2O的加入,能降低催化剂的酸性,减缓反应过程中催化活性物种NiO的过度还原,并抑制异丁烷裂解及积炭生成等副反应,从而提高了异丁烯的收率以及催化剂的稳定性。     

Dehydrogenation of isobutane in the presence of carbon dioxide over supported vanadium oxide catalysts

Summary The dehydrogenation of isobutane to isobutene in the presence of carbon dioxide was carried out over supported vanadium oxide catalysts. The influence of the support on the catalytic performance was investigated. The isobutane conversion and isobutene selectivity in the presence of carbon dioxide were compared with the results obtained during the dehydrogenation reaction in the presence of helium (inert gas). The catalysts were characterized by temperature-programmed techniques (TPR, TPD-NH₃, TPD-CO₂).     

Kinetics of the Oxidative Dehydrogenation of Isobutance over Cr2o3／La2（CO3）3

The oxidative dehydrogenation (ODH) of isobutane over Cr2O3/La2(CO3)3 has been investi- gated in a low-pressure Knudsen cell reactor, under conditions where the kinetics of the primary reaction steps can be accurately determined. By heating the catalyst at a constant rate from 150-300oC, temper- ature uctuations due to non-equilibrium adsorption are minimized. The evolved gas profiles show that ODH to isobutene and water is a primary reaction pathway, while carbon dioxide, which forms from the catalyst during reaction, is the only other product. This CO2 evolution may enhance the activity of the catalyst. Isobutene formation proceeds with the participation of lattice oxygen from the Cr2O3/La2(CO3)3 catalyst. The small pre-exponential factor is expected for a concerted mechanism and for such a catalyst with a small surface area and limited porosity.     

Catalytic dehydrogenation of isobutane in the presence of carbon dioxide

Summary The dehydrogenation of isobutane to isobutene in the presence and absence of carbon dioxide is discussed on the basis of catalytic studies. The V-Mg-O catalysts have been prepared using different preparation procedures. The structure and texture of the V-Mg-O catalysts were characterized by several techniques including X-ray diffraction (XRD), BET surface area measurements and infrared spectroscopy (IR). The results show that carbon dioxide enhances isobutane conversion in the reaction carried out over the V-Mg-O catalyst prepared by citrate method.     

Kinetics of the Oxidative Dehydrogenation of Isobutane over Cr2O3/La2(CO3)3

The oxidative dehydrogenation (ODH) of isobutane over Cr2O3/La2(CO3)3 has been investi-gated in a low-pressure Knudsen cell reactor, under conditions where the kinetics of the primary reactionsteps can be accurately determined. By heating the catalyst at a constant rate from 150-300 ℃, temper-ature fluctuations due to non-equilibrium adsorption are minimized. The evolved gas profiles show thatODH to isobutene and water is a primary reaction pathway, while carbon dioxide, which forms from thecatalyst during reaction, is the only other product. This CO2 evolution may enhance the activity of thecatalyst. Isobutene formation proceeds with the participation of lattice oxygen from the Cr2O3/La2(CO3)3catalyst. The intrinsic Arrhenius rate constant for the ODH of isobutane isk(s-1) = 1011.5±2.2exp{-((55 ± 5) - △Hads kJmol-1)/RT}The small pre-exponential factor is expected for a concerted mechanism and for such a catalyst with asmall surface area and limited porosity.     

不同载体负载的Cr基催化剂催化CO2氧化异丁烷脱氢制异丁烯

制备了介孔分子筛MSU-1,γ-A12O3,AC(活性炭)和MgO负载的CrOx催化剂,并考察了其催化CO2氧化异丁烷脱氢制异丁烯反应性能.结果表明,各催化剂活性的顺序为:CrOx/MSU-1 ＞CrOx/A12O3＞ CrOx/AC＞ CrOJMgO.其中在CrOx/MSU-1催化剂上,异丁烷的转化率和异丁烯的收率分...     

Investigation of the characteristics and deactivation of catalytic active center of Cr-Al_2O_3 catalysts for isobutane dehydrogenation

Deactivation mechanism of Cr-Al2O3 catalyst and the interaction of Cr-Al in the dehydrogenation of isobutane, as well as the nature of the catalytic active center, were studied using XRD, SEM, XPS, H2-TPR, isobutane-TPR and TPO techniques. The results revealed that the deactivation of Cr-Al2O3 catalyst was mainly caused by carbon deposition on its surface. The Cr3+ion could not be reduced by hydrogen but could be reduced to Cr2+by hydrocarbons and monoxide carbon. The active center for isobutane dehydrogenation could be Cr2+/Cr3+produced from Cr6+by the on line reduction of hydrocarbon and carbon monoxide. The binding energy of Al3+was strongly affected by the state of chromium cations in the catalysts.     

碳催化剂用于异丁烷直接脱氢制异丁烯

异丁烯用途广泛,被认为是除乙烯和丙烯外最重要的基础化工原料.异丁烯的来源主要是石油裂化过程中产生的碳四馏分,但随着对其需求量的逐年增加,分离法已逐渐无法满足,因此异丁烷直接脱氢工艺逐渐受到工业界和学术界的重视.铬系和铂系催化剂是两类传统工业催化体系,但铬对环境污染严重,铂作为贵金属成本较高,而且现有工艺大多存在催化剂稳定性较差需要反复再生的问题.近年来碳材料用于烷烃氧化脱氢反应的研究较多,并表现出较高的活性和稳定性,甚至有研究组提出金属催化剂在反应中快速生成的活性积碳(active coke)可能是真正的催化活性中心.但氧化脱氢反应不同于直接脱氢,需在反应中加入氧气,这在实际生产中会带来一系列问题：考虑到烷烃的爆炸极限,实际应用时反应气必须稀释,这不利于产物的收集;而且氧气会导致反应物过度氧化产生CO和CO2等副产物,也限制了氧化脱氢工艺在工业上的应用和发展.
　　我们研究组将椰壳碳、煤质碳和碳纳米管等碳材料作为催化剂用于催化异丁烷直接脱氢反应,发现碳催化剂表现出较高的催化活性：在625 oC,椰壳碳上异丁烷转化率和异丁烯选择性分别为70%和78%,连续反应3d后仍能维持34%的转化率,且选择性基本不变.与铬基催化剂相比,碳催化剂在稳定性方面表现出更大优势.我们进一步采用N2吸脱附、X射线光电子能谱(XPS)、傅里叶变换红外光谱(FTIR)和场发射扫描电子显微镜(FE-SEM)等手段对反应前后的碳催化剂进行了详细表征. N2吸脱附结果表明,椰壳碳比表面积高达1190.2 m2/g,这可能是其具有较高催化活性的原因;而结合催化剂活性数据,对比反应前后椰壳碳催化剂比表面积和异丁烷转化率可知,两者呈现近乎线性的相关性,进一步证实比表面积大小对碳催化剂催化活性有重要影响. XPS谱图证明椰壳碳在反应前表面除了有少量硅(0.73%)外,不存在金属氧化物等杂质,证实碳材料无需负载氧化物等即可表现出较高的催化活性;反应后沉积的积碳附着在催化剂表面,使硅含量降低至0.47%;催化剂中氧含量也由4.43%降低至3.78%,同时有碳酸盐生成. FTIR谱图进一步证实反应前的椰壳碳表面有丰富的有机官能团,但反应开始后有机官能团很快消失,而催化剂仍保持较高的催化活性,因此有机官能团并非碳催化剂催化活性高的必要因素,这与文献中已报道的结果不同. FE-SEM照片中观察到反应后椰壳碳催化剂表面形成积碳,随着反应时间延长积碳明显增多,这与XPS结果一致.
　　碳材料具有来源广泛、绿色环保等显著优势,可作为一种新的催化体系应用于异丁烷直接脱氢反应,无需负载其他物质或添加氧化性气体即可表现出良好的催化活性和稳定性,其比表面积对催化活性有重要影响,反应中产生的积碳导致催化剂比表面积下降进而降低其催化活性,而有机官能团的存在对催化活性影响不大.     

异丁烷在Cr2（MOO4）3,Fe2（MoO4）3催化剂上的无氧脱氢与氧化脱氢

研究了Ｃｒ２（ＭｏＯ４）３、Ｆｅ２（ｍＯ４）３、对异丁烷无氧脱氢与氧化氢的催化性能，在无氧脱氧反应中，催化剂的表面酸性既有利于异丁烷活性生成异丁烯，又易引起裂和异构化等副反应，在氧化脱氢反应中，异丁烯选择性较低，催化剂的表面酸中心对反应中间体的吸附将导致深度氧化。     

V2O5/SiO2催化剂的异丁烷选择氧化反应性能

 采用溶胶－凝胶法和浸渍法制备了V2O5／SiO2催化剂,并用XRD,IR,TPD和活性评价等手段对催化剂的表面构造、化学吸附性能和异丁烷选择氧化反应性能进行了研究．结果表明：催化剂表面由Lewis碱位V＝O双键的端氧和Lewis酸位V5＋构成,异丁烷分子主要通过甲基中的H双位吸附在催化剂表面的Lewis碱位上,异丁烯分子可通过甲基的H吸附在催化剂表面的Lewis碱位,也可通过C＝C双键吸附在催化剂表面的Lewis酸位上．在常压条件下,异丁烷选择氧化产物主要有异丁烯、甲基丙烯醛和甲基丙烯酸,其中深度氧化产物CO2主要由通过C＝C吸附的异丁烯继续反应生成．     

Catalytic Oxidative Dehydrogenation of Isobutane over KF-Zn_3(PO_4)_2

ＩｎｔｒｏｄｕｃｔｉｏｎＡｌｔｈｏｕｇｈｔｈｅｃａｔａｌｙｔｉｃｄｅｈｙｄｒｏｇｅｎａｔｉｏｎｏｆｉｓｏｂｕｔａｎｅｉｎｔｏｉｓｏｂｕｔｅｎｅｈａｓｂｅｅｎｃａｒｒｉｅｄｏｕｔｉｎｃｏｍｍｅｒｃｉａｌｐｌａｎｔｓｏｖｅｒＣｒ２Ｏ３－Ａｌ２Ｏ３ｏｒｎｏ...     

异丁烷在钼酸锌上的催化氧化脱氢

研究了钼酸锌对异丁烷氧化脱氢反应的催化作用,考察了原料气中烷氧体积比、N₂及水蒸汽对反应结果的影响.提高反应原料气中的烷氧体积比能够提高异丁烯选择性,但也会降低异丁烷的转化率.原料气中加入N₂不利于反应;而加入水蒸汽可提高异丁烯选择性.催化剂表面主要是弱酸中心,对反应有利.     

MoO3/SiO2催化剂的异丁烷选择氧化反应性能

分别采用浸渍法和溶胶－凝胶法制备了MoO3/SiO2催化剂，用XRD，TPR，IR，TPD和活性评价等手段对催化剂的影响，晶格氧活泼性，化学吸附性能和异丁烷选择氧化反应性能进行了研究。结果表明，催化剂表面由Lewis碱位Mo=M,Mo-O-Mo中的晶格氧和Lewis酸位Mo^6 构成，在MoO3/SiO2催化剂上，异丁烷主要通过甲基的H双位吸附在表面的Lewis碱位Mo=O上；在常压条件下，异丁烷选择氧化产物主要为异丁烷，甲基丙烯醛和甲基丙烯酸，其中深度氧化产物CO2主要由吸附的异丁烯继续反应生成；采用溶胶－凝胶法制备的MoO3/SiO2催化剂，可得到较高的异丁烷转化率和含氧有机物选择性。     

Dehydrogenation of isobutane with carbon dioxide over a vanadium-magnesium oxide catalyst

The activity of the vanadium-magnesium oxide catalyst was tested in the reaction of isobutane dehydrogenation reaction in the presence and absence of carbon dioxide. The data were compared with the results obtained in the Boudouard and the reverse water gas shift reactions. It has been found that carbon oxide is produced with both RWGS reactions coupled with the simple dehydrogenation of isobutane (i.e., two-step pathway) and the one-step oxidative dehydrogenation reaction.     

Dehydrogenation of Isobutane to Isobutene with Carbon Dioxide over SBA‐15‐Supported Chromia‐Ceria Catalysts

A series of SBA‐15‐supported chromia‐ceria catalysts with 3% Cr and 1%–5% Ce (3Cr‐Ce/SBA) were prepared using an incipient wetness impregnation method. The catalysts were characterized by XRD, N₂ adsorption, SEM, TEM‐EDX, Raman spectroscopy, UV–vis spectroscopy, XPS and H₂‐TPR, and their catalytic performance for isobutane dehydrogenation with CO₂ was tested. The addition of ceria to SBA‐15‐supported chromia improves the dispersion of chromium species. 3Cr‐Ce/SBA catalysts are more active than SBA‐15‐supported chromia (3Cr/SBA), which is due to a higher concentration of Cr⁶⁺ species present on the former catalysts. The 3Cr‐3Ce/SBA catalyst shows the highest activity, which gives 35.4% isobutane conversion and 89.6% isobutene selectivity at 570 °C after 10 min of the reaction.     

CATALYTIC OXYDEHYDROGENATION OF ISOBUTANE OVER LITHIUM-BASED OXIDES

研究了一些锂基氧化物对异丁烷的催化氧化脱氢作用，其中Ｌｉ２ＳｎＯ３显示出优良的催化性质，Ｌｉ２ＭｎＯ３，ＬｉＦｅ５Ｏ８和ＬｉＡｌ５Ｏ８对异丁烯的选择性较差，而Ｌｉ２ＣｅＯ３，ＬｉＦｅＯ２和ＬｉＺｎＯ２在反应条件下不稳定。系列ＬｉＳｎＯ催化剂的ＣＯ２ＴＰＤ分析表明，当ＳｎＯ２转化为Ｌｉ２ＳｎＯ３时，在表面形成了碱中心，它有利于异丁烯从催化剂表面脱附。Ｏ２ＴＰＤ和Ｈ２ＴＰＤ结果表明，此时吸附的氧物种数量降低，异丁烯的深度氧化受到抑制。Ｌｉ２ＳｎＯ３中晶格氧物种的活性对异丁烷催化氧化脱氢可能是适宜的，但不利于深度氧化。     

Cr对Pt-Sn /γ-Al2O3催化剂丙烷脱氢性能的影响

通过H2-TPR、O2-脉冲等表征手段，结合丙烷脱氢催化性能考察了助剂Cr对Pt-Sn/γ-Al2O3催化剂反应性能的影响。结果表明，添加少量Cr可显著改善Pt-Sn/γ-Al2O3催化剂的脱氢稳定性，可提高丙烯选择性，降低催化剂表面积炭量。这是由Cr和Pt-Sn之间存在的协同作用引起的，一方面，Pt促进了Cr的还原，生成了可提高丙烯选择性的+3价Cr；另一方面，Cr使Sn变得难于还原，在强还原气氛下保持了活性氧化态价态，进而改善了催化剂的脱氢稳定性。     

纳米Cr2O3系列催化剂上CO2氧化乙烷脱氢制乙烯反应

 采用溶胶－凝胶法和共沸蒸馏法耦合技术制备了纳米Cr2O3催化剂，并采用共沉淀法和共沸蒸馏法耦合技术制备了纳米Cr2O3／Al2O3，Cr2O3／ZrO2和Cr2O3／MgO复合催化剂．应用BET，XRD，XPS，TPR和TEM等物理化学方法对催化剂的结构和物化性质进行了表征，并考察了该系列催化剂上CO2氧化乙烷脱氢制乙烯的反应性能．结果表明，纳米Cr2O3催化剂上乙烷和CO2的转化率均明显高于常规Cr2O3催化剂，但乙烯的选择性低于常规Cr2O3催化剂；纳米复合催化剂中的复合成分显著影响催化剂的催化性能．其中，10％Cr2O3／MgO纳米复合催化剂在温度为973K时，乙烷转化率和乙烯选择性分别可达到61．54％和94．79％．纳米催化剂表面Cr的还原性以及Cr6＋／Cr3＋比值是影响乙烷转化率和乙烯选择性的重要因素．     

甲基叔丁基醚(MTBE)的合成

介绍了甲醇、异丁烯合成甲基叔丁基醚的催化剂、热力学、动力学。综述了合成ＭＴＢＥ的主要原料异丁烯的生产过程，并总结了甲醇、异丁醇和甲醇、叔丁醇合成ＭＴＢＥ的研究开发进展。参考文献１６篇。     

纳米Cr2O3的制备、表征及催化性能

首次采用溶胶-凝胶法与共沸蒸馏法耦合技术制备了纳米Cr2O3粉体，并运用BET、TEM、XRD、FT-IR、XPS及H2-TPR对其进行表征，同时采用CO2氧化乙烷脱氢制乙烯反应作为探针反应，考察了纳米Cr2O3的催化性能。首次发现纳米ErgO3的FT-IR谱出现了蓝移现象，并且630cm^-1附近的伸缩振动峰强度增强。初步探讨了纳米氧化物的IR蓝移和红移的原因，指出晶型是影响纳米氧化物红外光谱特征的重要因素。实验结果表明纳米Cr2O3上乙烷和CO2转化率均明显高于常规Cr2O3催化剂；在700℃下，乙烷转化率高达77．1％，而乙烯产率达到了58．98％。