Kinetics of the Oxidative Dehydrogenation of Isobutance over Cr2o3／La2（CO3）3

The oxidative dehydrogenation (ODH) of isobutane over Cr2O3/La2(CO3)3 has been investi- gated in a low-pressure Knudsen cell reactor, under conditions where the kinetics of the primary reaction steps can be accurately determined. By heating the catalyst at a constant rate from 150-300oC, temper- ature uctuations due to non-equilibrium adsorption are minimized. The evolved gas profiles show that ODH to isobutene and water is a primary reaction pathway, while carbon dioxide, which forms from the catalyst during reaction, is the only other product. This CO2 evolution may enhance the activity of the catalyst. Isobutene formation proceeds with the participation of lattice oxygen from the Cr2O3/La2(CO3)3 catalyst. The small pre-exponential factor is expected for a concerted mechanism and for such a catalyst with a small surface area and limited porosity.     

In situ UV-vis-NIR diffuse reflectance and Raman spectroscopy and catalytic activity studies of propane oxidative dehydrogenation over supported CrO3/ZrO2 catalysts

The molecular structures, oxidation states, and reactivity of 3 and 6% CrO3/ZrO2 catalysts prepared by incipient wetness impregnation were examined under different conditions. The in situ Raman spectroscopic studies under dehydrated conditions reveal that the 3 and 6% CrO3/ZrO2 catalysts possess equal amounts of monochromate and polychromate species. Consequently, monolayer coverage on this ZrO2 support is about 3% CrO3. The 6% CrO3/ZrO2 possesses an additional Raman band due to Cr2O3 crystals corresponding to the remaining 3% CrO3. Furthermore, during reaction conditions the polychromate species is preferentially reduced, the monochromate species are slightly affected, and the Cr2O3 crystals are not affected. The in situ UV-vis-NIR diffuse reflectance spectroscopy results reveal that under steady-state reaction conditions the extent of reduction and edge energy position of surface Cr6+ cations increase with an increase in reduction environment for the 3 and 6% CrO3/ZrO2 samples. Propane oxidative dehydrogenation (ODH) studies reveal that the catalytic activity expressed in moles of propane converted per gram catalyst per second is similar for the two catalysts, which is consistent with equal amounts of molecularly dispersed chromia present. The turnover frequency for the 6% CrO3/ZrO2 catalyst is, however, smaller than that for the 3% CrO3/ZrO2 sample due to the presence of Cr2O3 crystals, which are relatively inactive for propane ODH. For this catalytic system and for the experimental conditions used, propene, CO, and CO2 are primary products. Furthermore, the 33-39% propene selectivity is not affected by the C3H8/O2 ratio for both catalysts. Structure-reactivity studies suggest that the molecularly dispersed species are present in equal amounts in the 3 and 6% CrO3/ZrO2 samples as Cr6+ monochromate and polychromate species are the most effective catalytic active sites taking part in the propane ODH reaction.     

Cr2O3催化剂上甲烷部分氧化制备合成气

分别采用柠檬酸络合法和直接分解法制备了Cr2O3催化剂, 采用XRD, BET, TPR, XPS, TEM和TGA表征了催化剂的物理化学性质, 在常压固定床石英管(内径5 mm)反应器中考察了Cr2O3催化剂对甲烷部分氧化反应的催化性能. 在500~750 ℃, V(CH4)∶V(O2)=2, 空速12×104 h-1的条件下, O2几乎完全转化, CH4转化率及H2和CO选择性随着温度的升高而增加. 700 ℃下CH4转化率及H2, CO选择性随着空速(6.0×104~24×104 h-1)的升高而增加. 在500 h稳定性实验中, 随着反应时间的延长, CH4转化率及H2, CO选择性缓慢下降, XRD, TEM和BET结果表明, 催化剂的活性下降与烧结和团聚有关, TGA分析表明催化剂具有良好的抗积炭性. 通过CH4脉冲反应, 推测在反应过程中CO, H2, CO2和H2O是直接生成的.     

Coupling dehydrogenation of isobutane in the presence of carbon dioxide over chromium oxide supported on active carbon

The dehydrogenation of isobutane （IB） to produce isobutene coupled with reverse water gas shift in the presence of carbon dioxide was investigated over the catalyst Cr2O3 supported on active carbon （Cr2O3/AC）. The results illustrated that isobutane conversion and isobutene yield can be enhanced through the reaction coupling in the presence of carbon dioxide. Moreover, carbon dioxide can partially eliminate carbonaceous deposition on the catalyst and keep the active phase （Cr2O3）, which are then helpful to alleviate the catalyst deactivation.     

La2O3对Ni/γ-Al2O3甲烷化催化剂的助催化作用

我国将稀土作为助剂引入镍基甲烷化催化剂，大大提高了催化剂的活性和热稳定性，并已投入工业应用［1－3］．稀土对不同镍催化剂反应性能及其作用机理的研究已有一些报导［3－7］．谢有畅等观察到镍负载在经单层La2O3改性的γ－Al2O3表面，其晶粒要比没有La2O3时小得多．Rotgerink等认为添加La后反应速率的增加不只是由于几何效应，而是La对甲烷化本身有促进作用，单位镍表面的活性是随La含量不同而改变的，活性增加的同时表观活化能也增加［5］．作为助剂的La2O3在氢还原和反应过程中的变化及其作用的研究和讨论较少，目前一般认为添…     

Investigation of the characteristics and deactivation of catalytic active center of Cr-Al_2O_3 catalysts for isobutane dehydrogenation

Deactivation mechanism of Cr-Al2O3 catalyst and the interaction of Cr-Al in the dehydrogenation of isobutane, as well as the nature of the catalytic active center, were studied using XRD, SEM, XPS, H2-TPR, isobutane-TPR and TPO techniques. The results revealed that the deactivation of Cr-Al2O3 catalyst was mainly caused by carbon deposition on its surface. The Cr3+ion could not be reduced by hydrogen but could be reduced to Cr2+by hydrocarbons and monoxide carbon. The active center for isobutane dehydrogenation could be Cr2+/Cr3+produced from Cr6+by the on line reduction of hydrocarbon and carbon monoxide. The binding energy of Al3+was strongly affected by the state of chromium cations in the catalysts.     

La2O3/MgO催化剂上的甲烷氧化偶联

研究了甲烷在La_2O_3/MgO催化剂上的氧化偶联。发现制备过等对催化剂的行为有显著影响。比较了催化剂的反应性能和体相结构,表明在MgO上存在着三种La_2O_3的状态:高分散La_2O_3是最活泼的;La(OH)_3不太活泼;而呈六方晶相的La_2O_3晶粒活性最低。在催化剂中加入Na_2CO_3和K_2CO_3可以改进催化剂的活性和选择性。还考察了反应条件如温度和空速的影响。     

La2O3对沼气重整制氢催化剂Ni/γ-Al2O3的影响

用浸渍法制备了不同La2O3含量的Ni/La2O3/γ-Al2O3催化剂, 用CH4/CO2体积比为1的混合气体模拟沼气, 考察了La2O3对沼气重整制氢催化剂Ni/γ-Al2O3的结构及催化性能的影响. 运用XRD、H2-TPR、BET及TEM等手段对催化剂进行了表征. 结果表明, La2O3对催化剂Ni/γ-Al2O3的影响主要取决于其含量. 载体中La2O3的添加增强了Ni与Al2O3之间的相互作用. 添加适量的La2O3能使催化剂具有更好的可还原性, 并能增加金属Ni的分散性, 抑制反应过程中Ni的烧结, 提高载体对CO2的吸附能力, 从而改善了催化剂的抗积炭性, 使催化剂具有较好的活性及稳定性. 反之, 过量La2O3的掺杂会使催化剂的抗积炭性及活性下降. 当La2O3含量为6%(w)时, 催化剂中Ni晶粒具有较好的分散性、还原性及抗积炭性, 从而使催化剂具有更好的活性及稳定性.     

Ag/La0.6Sr0.4MnO3基催化剂上CH3OH和CO的完全氧化

合成了Ａｇ／Ｌａ０．６Ｓｒ０．４ＭｎＯ３、Ａｇ／Ｌａ０．６Ｓｒ０．４ＭｎＯ３／γ－ＡＩ２Ｏ３两毓催化剂，发现钙钛矿型Ｌａ０．６Ｓｒ０．４ＭｎＯ３对低浓度ＣＨ３ＯＨ或ＣＯ的完全氧化显示出相当高的催化活性，适量Ａｇ对钙钛矿型Ｌａ０．６Ｓ５０．４ＭｎＯ３基质的修使其对ＣＨ３ＯＨ或ＣＯ完全氧化催化活性获明显提高；在６％Ａｇ／２０％Ｌａ０．６Ｓｒ０．４ＭｎＯ３／γ－ＡＩ２Ｏ３催化剂 ，ＣＨ３ＯＨ完全氧化的Ｔ     

La2O3助剂对CH4部分氧化制氢Ni-Cu/ZrSiO催化剂的影响

用等体积浸渍法制备了ZrO2-SiO2(ZrSiO)表面复合氧化物负载的Ni-Cu双金属催化剂，并用TPR、XPS、IR、TPD及微反技术考察了稀土La2O3助剂对CH4和H2O在Ni-Cu/ZrSiO催化剂表面上的吸附及甲烷部分氧化制氢反应性能的影响。结果表明，加入La2O3助剂使催化剂表面Ni, Cu原子电子云密度增加，CH4和H2O在催化剂表面上的吸附增强；在反应温度450 ℃、进料摩尔比n-CH4∶nO2∶nH2O＝1∶0-5∶2-5以及甲烷空速SV(CH4)＝1 200 h－1的条件下，催化剂Ni-Cu-La2O3/ZrSiO上CH4转化率大于90％，生成H2的选择性高于99％，副产物CO的选择性仅为1.1％。根据实验结果，讨论了La2O3助催化剂的作用机理。     

CO2选择性氧化甲烷制C2烃催化剂La2O3/ZnO的氧化还原和CO2吸附性能

Ｌａ２Ｏ３／ＺｎＯ催化剂体系在以二氧化碳作为氧化剂的甲烷氧化偶联反应中具有很高的Ｃ２烃选择性和稳定性．采用ＣＯ２－ＴＰＤ－ＭＳ和ＴＰＲ技术考察了Ｌａ２Ｏ３／ＺｎＯ对ＣＯ２的吸附性质及其氧化还原行为．结果表明：（１）Ｌａ２Ｏ３／ＺｎＯ催化剂体系存在着强、弱两种碱中心，其中弱碱中心数量随样品中Ｌａ２Ｏ３含量增加而减少，强碱中心强度随样品中Ｌａ２Ｏ３含量增加而增强．（２）由于组分相互作用，高温下，Ｌａ２Ｏ３／ＺｎＯ易产生晶格氧空位，使之对ＣＯ２的吸附增强，吸附后的ＣＯ２与晶格氧作用形成立方晶型Ｌａ２Ｏ２ＣＯ３．（３）Ｌａ２Ｏ３／ＺｎＯ表面的Ｌａ３＋和Ｚｎ２＋可以部分被还原，由于组分间的相互作用，使得二者的还原都较单一组分存在时更难．（４）Ｈ２－ＣＯ２－Ｈ２氧化还原循环实验表明，Ｌａ２Ｏ３／ＺｎＯ表面被部分还原后，ＣＯ２可以将部分被还原的表面再氧化．在此基础上对Ｌａ２Ｏ３／ＺｎＯ催化剂上甲烷与ＣＯ２转化为Ｃ２烃的机制也进行了讨论．     

MoO3/SiO2催化剂的异丁烷选择氧化反应性能

分别采用浸渍法和溶胶－凝胶法制备了MoO3/SiO2催化剂，用XRD，TPR，IR，TPD和活性评价等手段对催化剂的影响，晶格氧活泼性，化学吸附性能和异丁烷选择氧化反应性能进行了研究。结果表明，催化剂表面由Lewis碱位Mo=M,Mo-O-Mo中的晶格氧和Lewis酸位Mo^6 构成，在MoO3/SiO2催化剂上，异丁烷主要通过甲基的H双位吸附在表面的Lewis碱位Mo=O上；在常压条件下，异丁烷选择氧化产物主要为异丁烷，甲基丙烯醛和甲基丙烯酸，其中深度氧化产物CO2主要由吸附的异丁烯继续反应生成；采用溶胶－凝胶法制备的MoO3/SiO2催化剂，可得到较高的异丁烷转化率和含氧有机物选择性。     

整体式Pd/La_2O_3-Al_2O_3和Pd/CeO_2-ZrO_2-Y_2O_3催化剂上汽油车尾气净化性能的比较

采用共沉淀法制备了耐高温高比表面积的La2O3-Al2O3(LA)材料和CeO2-ZrO2-Y2O3(CZY)储氧材料,并用浸渍法制备了整体式Pd/LA和Pd/CZY汽油车尾气净化三效催化剂,考察了它们的三效催化性能和空燃比性能,并单独通过水煤气变换和CO氧化反应性能的考察,探讨了两种催化剂空燃比窗口扩大的原因.结果表明,Pd/CZY催化剂三效窗口明显较宽,且催化氧化CO的性能明显更优;对于CO+NO反应,Pd/CZY催化剂的活性较高.当反应中逐步通入O2后,抑制了该反应的进行,但CO氧化的转化率升高,而NO转化率降低,直至CO+NO反应完全被抑制,表明CO氧化反应对于抑制催化剂在NO贫燃方向的窗口具有一定的作用.另外,Pd/CZY催化剂上对于水煤气变换反应性能明显优于Pd/LA催化剂,在一定温度下逐步通入O2后,不会抑制水煤气变换反应的发生;当逐步通入NO时,可以促进水煤气变换反应的进行,表明Pd/CZY催化剂在富燃时对扩展CO转化窗口的性能明显优于Pd/LA催化剂.     

甲烷氧化偶联催化剂La2O3／SrCO3—BaCO3的催化活性与表征

在甲烷氧化偶联制Ｃ２烃的研究中，人们发现碱土金属与稀土金属组成的复合氧化物催化剂具有高的催化活性［１，２］．稀土化合物作为有希望的工业催化剂之一，已受到广泛的关注．一般认为，它们含有的氧空位对活化甲烷的有效氧物种有利．Ｄｅｂｅｙ等在１％Ｓｒ／Ｌａ２Ｏ...     

Ni-Fe/La2O2CO3催化乙醇水蒸气重整制氢的研究

采用La2(CO3)3空气焙烧法制备了La2O2CO3载体、采用浸渍法制备了Ni,Fe不同比例的Ni-Fe双金属催化剂及Ni/La2O2CO3,Fe/La2 O2 CO3催化剂,考察了各催化剂从300～700℃催化乙醇水蒸气重整反应的性能,并用BET,XRD,TPR等技术对催化剂进行表征。结果表明,相对单一金属催化剂,Ni-Fe双金属催化剂均表现出更高的活性,这可能是因为高分散的Ni,Fe和LaFeyNi1-yO3的共存作用。其中Ni含量为10%,Fe含量为5%时的Ni-Fe/La2O2CO3表现出最高的活性,400℃时乙醇的转化率为100%,H2的选择性最高达到94.1%,而CO的选择性则低至1.2%。     

CO_2 reforming of glycerol over La-Ni/Al_2O_3 catalyst:A longevity evaluative study

This paper reports on the longevity of glycerol-dry(CO2) reforming over the lanthanum(La) promoted Ni/Al2O3 catalysts.The XRD results showed that the Ni particle was well-dispersed in the presence of La promoter.In addition,via the NH3-TPD analysis,it was found that the La promoter has reduced the acidity of Ni catalyst which may have explained the mitigation of carbon laydown.It was determined that the 3.0 wt% La-promoted Ni/Al2O3 catalyst possessed the largest BET specific surface area of 97 m2 g-1.Consequently,it yielded the best catalytic longevity performance with conversion attained more than 90%,even after 72 h of reaction duration.Significantly,it can be confirmed that the presence of CO2 during the glycerol dry reforming was essential in reducing carbon deposition,most likely via gasification pathway.This has ensured a stability of catalytic activity for a long reaction period(72 h).     

不同载体负载的Cr基催化剂催化CO2氧化异丁烷脱氢制异丁烯

制备了介孔分子筛MSU-1,γ-Al2O3,AC(活性炭)和MgO负载的CrOx催化剂,并考察了其催化CO2氧化异丁烷脱氢制异丁烯反应性能.结果表明,各催化剂活性的顺序为:CrOx/MSU-1>CrOx/Al2O3>CrOx/AC>CrOx/MgO.其中在CrOx/MSU-1催化剂上,异丁烷的转化率和异丁烯的收率分别为59.2%和39.5%.同时,利用N2吸附-脱附、X射线衍射、X射线光电子能谱和程序升温脱附对催化剂进行了表征.结果表明,载体的比表面积对相应催化剂的初始活性有一定的影响;当CrOx负载量较低时,以单层分散于载体上,且含有较多孤立状态Cr6+时催化剂的活性更高.另外,催化剂表面的弱酸性也会影响其活性;而碱性位的存在可提高催化剂稳定性.     

Catalytic Conversion of Methanol by Oxidative Dehydrogenation

This study investigates the effects of addition of oxygen on the oxidative dehydrogenation (ODH) of methanol when a fluorotetrasilicic mica ion-exchanged with palladium (Pd2 -TSM) was used as the catalyst. The reaction proceeded at a very low temperature in the presence of oxygen, and HCOOCH3 was obtained at high selectivity. By calculating the equilibrium conversion, it has been shown that substantial ODH took place for HCOOCH3 production. Consequently, this reaction would make dehydrogenation the dominant reaction at equilibrium. Not all the H dissociated from CH3OH was converted to H2O by oxidation. It has been shown that the H2O was not produced from oxidative dehydrogenation by the direct reaction of CH3OH and O2 when an attempt was made to carry out oxidative dehydrogenation using an isotope oxygen trace method in the gas phase. Therefore, when CH3OH was converted to CO2 and dehydrogenated to HCOOCH3, the C—O bonds were not dissociated.     

碱性助剂的添加对Ni/CaO-Al2O3催化剂性能的影响

在CH4、 CO2和O2制合成气的反应中, 通过在Ni/CaO-Al2O3催化剂中添加碱性助剂K2O、 MgO和La2O3, 使催化剂的性能得到了改善. 实验结果表明, MgO和La2O3助剂的添加, 有利于提高催化剂的活性;添加K2O, 却相反. 测得催化剂上积炭量的顺序为: Ni-La2O3/CaO-Al2O3相似文献   

La2O3对Ni-Mo/γ-Al2O3催化剂CO和CO2甲烷化的影响

采用浸渍法制备了一系列Ｎｉ－Ｍｏ－Ｌａ／γ－Ａｌ２Ｏ３催化剂并测定了催化剂的ＣＯ和ＣＯ２甲 化活性采用ＴＥＭ，ＸＰＳ和ＣＯ化学吸附等手段研究了表面性质。结果表明，Ｌａ２Ｏ３的咖入提高了Ｎｉ－Ｍｏ／γ／Ａｌ２Ｏ３催化剂的ＣＯ和ＣＯ２甲烷化活性，增加了催化剂中Ｎｉ的分散度，活性表面积及催化剂表面Ｎｉ原子的浓度，降低了电子结合能。