Bending problems of non-homogeneous cylindrical orthotropic circular plate

ＢＥＮＤＩＮＧＰＲＯＢＬＥＭＳＯＦＮＯＮ－ＨＯＭＯＧＥＮＥＯＵＳＣＹＬＩＮＤＲＩＣＡＬＯＲＴＨＯＴＲＯＰＩＣＣＩＲＣＵＬＡＲＰＬＡＴＥＱｉｎＳｈｅｎｇ－ｌｉ（秦圣立）（ＱｕｆｕＮｏｒｍａｌＵｎｉｃｅｒｓｉｔｙ,Ｑｕｆｕ,Ｓｈａｎｄｏｎｇ）（Ｒｅｃｅｉ...     

Bending of Timoshenko beam with effect of crack gap based on equivalent spring model

Considering the effect of crack gap,the bending deformation of the Timoshenko beam with switching cracks is studied.To represent a crack with gap as a nonlinear unidirectional rotational spring,the equivalent flexural rigidity of the cracked beam is derived with the generalized Dirac delta function.A closed-form general solution is obtained for bending of a Timoshenko beam with an arbitrary number of switching cracks.Three examples of bending of the Timoshenko beam are presented.The influence of the beam’s slenderness ratio,the crack’s depth,and the external load on the crack state and bending performances of the cracked beam is analyzed.It is revealed that a cusp exists on the deflection curve,and a jump on the rotation angle curve occurs at a crack location.The relation between the beam’s deflection and load is bilinear,each part corresponding to an open or closed state of crack,respectively.When the crack is open,flexibility of the cracked beam decreases with the increase of the beam’s slenderness ratio and the decrease of the crack depth.The results are useful in identifying non-destructive cracks on a beam.     

考虑界面滑移效应的组合裂纹梁弯曲解析解

将上部子梁的裂纹等效为线性扭转弹簧,考虑组合梁连接面的滑移位移,建立了以组合裂纹梁挠度和滑移位移为基本未知量的组合裂纹梁弯曲变形一维数学模型．利用Laplace变换及其逆变换,给出了组合裂纹梁弯曲变形一维数学模型的解析通解．在此基础上,研究了均布载荷作用下简支组合裂纹梁的弯曲变形问题,数值分析了连接面剪切刚度、裂纹深度、数目和位置等参数对组合裂纹梁弯曲变形的影响,结果表明：在裂纹处,组合裂纹梁挠度曲线存在尖点,而横截面转角曲线存在跳跃,且随着裂纹数目和深度的增加,挠度和横截面转角跳跃值增大;随着连接面剪切刚度的增加,挠度和横截面转角减小,并最终趋于定值．并且,随着组合梁跨高比的增加,连接面剪切刚度对梁挠度影响逐渐减弱．     

Bending of a circular cylinder containing a crack

The study of bending of cracked circular cylinders is of more significance. The bending of cylinders containing radical crack or cracks was discussed by refs. [1]–[4] and that of concentrically craked circular cylinders was studied by [5]. Continuing [6] and using complex variable methods in elasticity, this paper deals with the bending problems of a circular cylinder, containing an internal linear crack at any position under an acting force perpendicular to the crack. The general forms of displacements, stresses, and stressintensity factors, expressed in terms of series, are obtained and to this bending problems with small Ah are presented good approximate formulas for the stress-intensity factors whose variations with the center of the crack are analysed. Finally, the twist angle per unit length and the center of bending for the radically cracked circular cylinder, one of whose crack-tips is located at the origin, have been computed and the results are almost the same as that calculated in [1].     

Winkler地基上变厚度圆板的轴对称弯曲

本文提出了Winkler地基上变厚度圆板轴对称弯曲的传递矩阵算法。首先,根据贝塞尔函数理论获得了等厚度圆板和环板单元在任意荷载作用下轴对称弯曲的解析解,这些解均由通解和特解两部分组成。基于这些解析解,导出了等厚度圆板和环板单元的传递矩阵。然后沿径向将变厚度圆板划分成一个等厚度圆板单元和一系列等厚度环板单元,应用传递矩阵算法原理获得了变厚度圆板的整体传递矩阵。引入圆板的边界条件,给出了该板每条节线上的挠度、径向转角、径向弯矩和径向剪力。最后,讨论了受均布荷载作用的简支线性变厚度圆板的弯曲,将本文数值解与解析解进行比较,证实了本文方法的有效性,并简要地讨论了地基参数对板挠度和径向弯矩的影响。     

基于等效黏性弹簧的黏弹性Timoshenko裂纹梁弯曲解析解

考虑裂纹的缝隙和黏性效应,将梁中横向裂纹等效为黏弹性扭转弹簧,利用广义Delta函数,给出了Laplace变换域内裂纹梁的等效抗弯刚度,得到了具有任意开闭裂纹数目且满足标准线性固体黏弹性本构的Timoshenko梁在时间域内的弯曲变形显式解析通解．在此基础上,通过两个数值算例,分析了时间、梁跨高比和裂纹深度等参数对黏弹性Timoshenko开裂纹梁弯曲变形的影响．结果表明：裂纹黏性对Timoshenko裂纹梁的弯曲具有显著的影响．相比于裂纹的弹性扭转弹簧模型,考虑裂纹黏性效应的黏弹性Timoshenko裂纹梁在裂纹处挠度尖点和转角跳跃现象十分明显．另外,由于横向剪切引起的附加变形,Timoshenko裂纹梁的稳态挠度与Euler-Bernoulli梁挠度的差值为常数,其大小与裂纹模型、梁跨高比或裂纹深度无关,这些结果对梁裂纹无损检测具有指导意义．     

考虑轴力二阶效应的损伤梁弯曲摄动解

将损伤梁等效为阶梯型变刚度Euler-Bernoulli梁，利用Heaviside广义函数，给出了阶梯型变刚度梁抗弯刚度的统一表达式．在此基础上，考虑轴向压力二阶效应，并以损伤为摄动参数，得到了均布横向载荷作用下，简支损伤梁弯曲挠度的一阶和二阶摄动解析解，并数值分析了摄动解析解的精度和损伤梁的弯曲变形特性，结果表明：随着轴向压力和刚度损伤参数的增加，挠度一阶和二阶摄动解析解误差增加，挠度二阶摄动解析解误差通常小于其一阶摄动解析解误差，且二阶摄动解的误差很小，满足工程应用的精度．同时，损伤梁的挠度和转角分布与完整梁的挠度和转角分布差异较大，在刚度变化位置处损伤梁转角斜率存在突变．这些结果可为轴力作用下Euler-Bernoulli梁损伤识别提供理论支撑．     

A study on caustic method in cracked plate under symmetric bending

Based on Chun-Tu Liu's result for Reissner's plate, an equation of caustics in cracked plate under symmetric bending was obtained. The shape and the distribution of light intensity of the caustic curve were discussed in detail. The relation between the stress intensity factor (SIF) and the size of the caustic curve was found by numerical method, and a simple and accurate experimental method for evaluating SIF in plate under bending was proposed.     

横观各向同性弹性半空间地基上四边自由各向异性矩形薄板弯曲解析解

选用更具广泛性的横观各向同性弹性半空间地基模型,来分析四边自由各向异性矩形地基板的弯曲解析解．将异性薄板的弯曲控制方程,与基于横观各向同性弹性半空间地基位移解建立的板与地基变形协调方程相结合,先按对称性分解,然后用三角级数法,得出横观各向同性弹性半空间地基上四边自由各向异性矩形薄板的弯曲解析解,包括地基反力、板的挠度及内力的解析表达式．该解析解克服了数值法的弊端,取消了对地基反力的假设,板的内力及地基反力求解更切实际．算例结果与文献结果吻合良好,证明本文方法的可行性．     

Bending of simply-supported circular timber beam strengthened with fiber reinforced polymer简

The bending behavior of the circular cross-section timber beam strengthened with a fiber reinforced polymer (FRP) sheet is investigated. The tight bonding is on the interface between the surface of a timber beam and the reinforcement layer of the FRP sheet. An analytical expression for the bending moment-curvature relation is presented, and its failure modes are analyzed. The governing equation for nonlinear small deflection of the FRP-strengthened circular timber beam is established, and the corresponding numerical method is given. The bending deformation of the simply-supported circular timber beam strengthened with the carbon fiber reinforced polymer (CFRP) sheet subject to a uniform load is studied numerically. The influence of the angle and thickness of the CFRP layer as well as the timber strength on the bending deflection of the FRP-strengthened circular timber beam is examined. It is revealed that, with the increases of the thickness and angle, the deflection of the CFRP-strengthened circular timber beam is decreased, and its carrying capacity and ductility are increased. However, when the angle of the layer reaches a certain value, the deflection will no longer decrease with the increase of the angle. At the same time, the nonlinear bending moment-curvature relation of the CFRP-strengthened circular timber beam is simplified as an approximate bilinear constitutive model. The approximate deflections of the simply-supported circular timber beam strengthened with the CFRP sheet are obtained. The results are compared with the linearly elastic bending and nonlinear bending models, showing that the mid-span deflections of a CFRP-strengthened circular timber beam with the approximate bilinear constitutive model are greater than those with the nonlinear constitutive model. The results of its stiffness analysis are on the safe side.     

矩形扁壳弯曲问题的一般解

本文建立了四边挠度为零的矩形扁壳弹性弯曲问题的一般解析解.以四边位移为零的固支矩形扁壳为例求解了对称变形问题。     

Boundary Conditions for Plate Bending in One-dimensional Hexagonal Quasicrystals

For plate bending in one-dimensional (1D) hexagonal quasicrystals (QCs), the reciprocal theorem and the general solution for QCs media are applied in a novel way to obtain the appropriate stress and mixed boundary conditions accurate to all order for plates of general edge geometry and loadings. Through generalizing the method developed by Gregory and Wan, a set of necessary conditions on the edge-data for the existence of a rapidly decaying solution is established. The prescribed data must satisfy these conditions in order that they should generate a decaying state. When a set of stress edge-data or mixed edge-data is imposed on the plate edge, these decaying state conditions for the case of axisymmetric deformation of 1D hexagonal QC plates are derived explicitly. They are then used for the correct formulation of boundary conditions for the plate theory solution (or the interior solution). Furthermore, in the absence of phonon–phason fields coupling effect, corresponding necessary conditions for the case of transversely isotropic elastic plates are derived subsequently, and their isotropic elastic counterparts are also obtained.      

Bending problems of rectangular Reissner plate with free edges laid on tensionless Winkler foundations

In this paper,an analytical method for solving the bending problems of rectangularReissner plate with free edges under arbitrary loads laid on tensionless Winkler foundationsis proposed.By assuming proper form of Fourier series with supplementary terms,whichmeet derivable conditions,for deflection and shear force functions,the basic differentialequations with given boundary conditions can be transformed into a set of simple infinitealgebraic equations.For common Winkler foundations,this set of equations can be solveddirectly and for tensionless Winkler foundations,it is a set of weak nonlinear algebraicequations,the solution of which can be obtained easily by using iterative procedures.     

反对称斜交叠层板双向弯曲问题的横向基理论解

研究反对称斜交叠层板的双向弯曲问题。根据横向基理论，在厚度方向，给出了三个方向位移沿厚度的分布规律；在面内方向，采用升阶谱位移函数；然后，应用最小势能原理导出叠层板的静力控制方程。通过对多种层数和铺层角的层板力学响应计算分析表明：在典型位置的应力分布，本文解与三维弹性解符合很好，并有较好的收敛性。     

阶梯式变厚度两对边简支的矩形弹性薄板弯曲问题的解析解

讨论了阶梯式变厚度两对边为简支的矩形弹性薄极的弯曲问题，应用奇异函数及其傅立叶奇延拓展开获得了该问题的通解和一系列特解。文中应用所得公式对实例进行了分析和计算。     

含圆孔缺陷三点弯曲梁动态焦散实验

应用新型数字激光动态焦散线实验系统,采用含预制裂纹的有机玻璃板试件进行落锤冲击实验,研究了含圆孔缺陷三点弯曲梁的动态断裂行为。通过实验得到了含圆孔缺陷三点弯曲梁裂纹尖端动态应力强度因子的变化情况、裂纹扩展速度的变化情况以及裂纹贯穿空孔的扩展情况等。实验结果表明:三点弯曲梁中的空孔位置对裂纹的扩展轨迹具有明显的导向作用;空孔位置的改变会影响三点弯曲梁的断裂时间;空孔位置的变化对空孔下方裂纹的扩展时间、扩展轨迹影响较小;在空孔位置居中的情况下,空孔上方裂纹的最大扩展速度大于空孔位置偏移时的情况。     

横观各向同性弹性半空间地基上正交异性矩形中厚板弯曲解析解

对横观各向同性体通解进行双重傅里叶变换,获得了直角坐标系下横观各向同性弹性半空间地基受任意竖向荷载作用下的位移积分变换解;在此基础上建立了板与地基的变形协调方程,并与三个广义位移变量描述的弹性地基上四边自由正交各向异性矩形中厚板的弯曲控制方程相结合,用三角级数法,得出横观各向同性弹性半空间地基上四边自由正交异性矩形中厚板受任意竖向荷载作用的弯曲解析解。相关算例分析表明,本文方法是有效的。     

Bending analysis of magnetoelectroelastic nanoplates resting on Pasternak elastic foundation based on nonlocal theory

Based on the nonlocal theory and Mindlin plate theory, the governing equations (i.e., a system of partial differential equations (PDEs) for bending problem) of magnetoelectroelastic (MEE) nanoplates resting on the Pasternak elastic foundation are first derived by the variational principle. The polynomial particular solutions corresponding to the established model are then obtained and further employed as basis functions with the method of particular solutions (MPS) to solve the governing equations numerically. It is confirmed that for the present bending model, the new solution strategy possesses more general applicability and superior flexibility in the selection of collocation points. The effects of different boundary conditions, applied loads, and geometrical shapes on the bending properties of MEE nanoplates are evaluated by using the developed method. Some important conclusions are drawn, which should be helpful for the design and applications of electromagnetic nanoplate structures.     

泡沫铝夹芯梁四点弯曲性能试验研究

通过准静态四点弯曲试验对泡沫铝夹芯梁的弯曲力学性能进行了测试,研究了它的破坏过程、破坏形态和典型荷载-位移曲线,分析了芯层厚度和面层厚度等参数对其弯曲力学性能的影响。结果表明,泡沫铝夹芯梁四点弯曲破坏过程历经三个阶段,呈现三种失效模式:整体弯曲破坏、局部屈曲破坏以及整体屈曲破坏;芯层厚度和面层厚度对夹芯梁的弯曲承载力和吸能效果有明显影响;在本试验参数范围内,芯层厚度为25mm,面层厚度为0.4mm时,夹芯梁具有最优弯曲力学性能。     

考虑轴力作用时梁的弯曲损伤失效分析

对考虑轴力作用时梁的弯曲损伤进行了分析,推导了其损伤分析的基本方程,分析表明,中性轴随损伤的发展而偏移,有向上、向下和保持不动三种情况,其偏移的方向和范围完全由比例加载系数决定,并且在特定的比例加载系数时,中性轴能保持不动,最后获得了梁在弯曲损伤时的中性轴起始偏移点、极限偏移点和极限载荷的计算公式,以及它们的简化计算公式;讨论了损伤极限状态时轴力和弯矩的交互作用曲线;轴力对弯曲损伤的影响较为显著,有轴力作用时应尽可能考虑其影响。