KF-alumina 催化下2-氨基-4-芳基-5,6-二氢化-4H-吡喃[3,2-c]喹啉-5-酮-3-羧酸酯衍生物的一步合成

以芳醛、氰乙酸酯和4-羟基喹啉-2-酮为原料, 乙醇为溶剂, 在KF-Al₂O₃催化下80 ℃, 一步合成了2-氨基-4-芳基-5,6-二氢化-4H-吡喃[3,2-c]喹啉-5-酮-3-羧酸酯衍生物, 和其它方法相比, 具有反应条件温和, 容易操作和产率高等优点, 产物4a的结构通过X单晶衍射分析确证.     

KF/Al2O3催化下4-芳基-9,10-二氢萘并[2,1-b]-4H-吡喃衍生物的合成

在KF/Al₂O₃催化下, α,β-不饱和腈或α,β-不饱和羧酸酯和7-甲氧基-1,2,3,4-四氢-2-萘酮反应, 生成了一系列4-芳基-9,10-二氢萘并[2,1-b]-4H-吡喃衍生物. 产物的结构通过红外光谱和核磁共振氢谱进行表征, 并通过X单晶衍射分析进一步证实产物的结构.     

xLi2MnO3-(1-x)LiNi0.7Co0.3O2的低温燃烧合成及电化学性能研究

采用低温燃烧法合成了锂离子电池正极材料xLi₂MnO₃-(1-x)LiNi_0.7Co_0.3O₂,对合成产物的结构、形貌和电化学性能进行了系统的研究, 通过单因素试验对合成条件和材料的组成进行了优化。结果表明:采用低温燃烧法合成的富锂层状正极材料具有α-NaFeO₂型层状结构、球状形貌和良好的电化学性能;其最佳合成条件为:回火温度850℃, 回火时间20 h;Li₂MnO₃的最佳配比为x=0.7.在此条件下合成的0.7Li₂MnO₃-0.3LiNi_0.7Co_0.3O₂,最高放电比容量达到263.1 mAh·g^-1,并具有良好的循环性能和倍率性能。     

Cr2O3和CrO3/Cr2O3催化剂的2-氯-1,1,1-三氟乙烷气相氟化反应的活性物种和失活

采用沉淀法和浸渍法制备了2种铬基（Cr₂O₃和CrO₃/Cr₂O₃）催化剂,用于气相氟化2-氯-1,1,1-三氟乙烷合成1,1,1,2-四氟乙烷。研究发现含有低价铬（Cr³⁺）物种的Cr₂O₃催化剂上2-氯-1,1,1-三氟乙烷的稳态转化率为18.5%,而含有高价铬（Cr⁶⁺）物种和低价铬（Cr³⁺）物种的CrO₃/Cr₂O₃催化剂初始转化率达到30.6%,然而存在明显的失活。含有Cr⁶⁺物种的CrO₃/Cr₂O₃催化剂的2-氯-1,1,1-三氟乙烷氟化反应初始TOF值为1.71×10^-4 mol_HCFC-133a·mol_Cr（Ⅵ）^-1·s^-1,高于含有Cr³⁺物种的Cr₂O₃催化剂（4.16×10^-5 mol_HCFC-133a·mol_Cr（Ⅲ）^-1·s^-1）。Cr₂O₃催化剂在氟化反应前后催化剂的物相结构保持不变;而含有高价铬物种的CrO₃/Cr₂O₃催化剂经HF反应后生成了CrO_xF_y活性物种。然而,CrO_xF_y物种在反应中挥发或转化成稳定但无活性的CrF₃,从而导致催化剂失活。     

Cr2O3和CrO3/Cr2O3催化剂的2-氯-1，1，1-三氟乙烷气相氟化反应的活性物种和失活

采用沉淀法和浸渍法制备了2种铬基（Cr₂O₃和CrO₃/Cr₂O₃）催化剂,用于气相氟化2-氯-1,1,1-三氟乙烷合成1,1,1,2-四氟乙烷。研究发现含有低价铬（Cr³⁺）物种的Cr₂O₃催化剂上2-氯-1,1,1-三氟乙烷的稳态转化率为18.5%,而含有高价铬（Cr⁶⁺）物种和低价铬（Cr³⁺）物种的CrO₃/Cr₂O₃催化剂初始转化率达到30.6%,然而存在明显的失活。含有Cr⁶⁺物种的CrO₃/Cr₂O₃催化剂的2-氯-1,1,1-三氟乙烷氟化反应初始TOF值为1.71×10^-4 mol_HCFC-133a·mol_Cr(Ⅵ)^-1·s^-1,高于含有Cr³⁺物种的Cr₂O₃催化剂（4.16×10^-5 mol_HCFC-133a·mol_Cr(Ⅲ)^-1·s^-1）。Cr₂O₃催化剂在氟化反应前后催化剂的物相结构保持不变;而含有高价铬物种的CrO₃/Cr₂O₃催化剂经HF反应后生成了CrO_xF_y活性物种。然而,CrO_xF_y物种在反应中挥发或转化成稳定但无活性的CrF₃,从而导致催化剂失活。     

一个新的双核锌配合物Zn2(dhaash)2(py)4的合成及晶体结构

The crystal of binuclear zinc complex Zn₂(dhaash)₂(py)₄ was obtained in DMF and pyridine, where H₂dhaash is 2,4-dihydroxy-5-acetylacetophenone-N-salicylhydrazone. It has been characterized by IR, UV, element analysis and X-ray single crystal diffraction. The crystallographic data were as follows: monoclinic system, space group P2₁/c, a=1.108 98(11) nm, b=1.640 84(16) nm, c=1.445 14(14) nm, β=108.617(2)°, Z=2, V=2.492 1(4) nm³, D_c=1.466 g·cm^-3, M_r=1 099.74, μ=1.031 mm^-1, F(000)=1 136 and the final R=0.044 8 and wR=0.105 8 for 4 143 observed reflections with I≥2σ(I), respectively. The X-ray crystal structure analysis revealed that, in the centrosymmetric binuclear complex molecule, two zinc(Ⅱ) centers are linked by two oxygen atoms (O(3) and O(3A)), respectively. Zn(1)…Zn(1A) distance is 0.314 81(6) nm, O(3)…O(3A) distance is 0.270 4(2) nm. Every zinc(Ⅱ) ion has an elongated octahedral coordination. For example, the two pyridine nitrogen atoms, one oxygen atom and one nitrogen atom from salicylhydrazone, one oxygen atom from 2,4-dihydroxy-5-acetylacetophenone in one dhaash^2- ligand and one oxygen atom from 2,4-dihydroxy-5-acetylacetophenone in another dhaash^2- ligand coordinated to zinc(Ⅱ) ion, respectively. Two zinc(Ⅱ) ions and all the 72 non-hydrogen atoms in the two dhaash^2- ligands are in the same plane. CCDC: 261929.     

纳米三氧化二钴低温热容和热力学性质的研究

The isobaric molar heat capacities of nano Co₂O₃ were determined by an adiabatic calorimeter in the temper-ature range from 78 to 350K. No phase transition takes place in this temperature range. The relationship of C_p，m with respect to thermodynamic temperature T was established as C_p，m=-11.998X³-9.6431X²+63.478X+81.291(J·K^-1·mol^-1) ， where X=(T-201.903)/121.535， the correlation coefficient R₂=0.9996. Ac-cording to this relationship and the relationships between thermodynamic functions， the thermodynamic functions of nano Co₂O₃ relative to the standard temperature of 298.15K were derived based on the measured heat capacity data. The average grain size of the studied nano Co₂O₃ sample was determined to be 12nm by TEM.     

一维双核锌配合物[Zn2(SHSH)2(2-Me-py)2]的合成、晶体结构及理论研究

The crystal of one-dimensional binuclear zinc complex [Zn₂(SHSH)₂(2-Me-py)₂] was obtained in DMF and 2-methylpyridine, where SHSH is salicylaldehyde salicylhydrazone. It has been characterized by IR, UV, element analysis and X-ray diffraction analysis. The crystallographic data were as follows: monoclinic system, space group P2₁/c, a=1.144 49 nm, b=1.206 69 nm, c=1.379 39 nm, β=97.039°, Z=2, V=1.890 6 nm³, M_r=825.47, D_c=1.450 g·cm^-3, μ=1.324 mm-1, F(000)=848 and the final R=0.033 6 and wR=0.094 7 for 3 752 observed reflections with I≥2σ(I). The theoretical investigation of title complex as a structure unit was carried out at B3LYP/6-31G and HF/6-31G levels with Guassian 03W program, and the atomic charges, natural bond orbital analysis and bond energies were also discussed. CCDC: 260920.     

Ni/SiO2-Al2O3催化乙酰丙酸加氢制γ-戊内酯

采用溶胶-凝胶法制备了一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,以该系列复合氧化物为载体,采用等体积浸渍法制备了Ni负载量15%（重量百分比）的催化剂,用于催化乙酰丙酸加氢制γ-戊内酯.采用N₂物理吸附、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、H₂程序升温脱附（H₂-TPD）、NH₃程序升温脱附（NH₃-TPD）和吡啶吸附红外（Py-IR）等手段对催化剂进行了表征.结果表明,不同载体催化剂的活性组分分散度及表面酸性质存在明显差异,显著影响了催化剂吸附、活化H₂与C=O键的能力,进而影响了催化剂的乙酰丙酸加氢活性.其中,Ni/SiO₂-Al₂O₃催化剂上的L酸中心能够促进C=O键的吸附、活化,与金属Ni上的H₂吸附活性位协同作用,大大提高了乙酰丙酸加氢活性.因此,具有最多L酸中心和丰富H₂吸附活性位的Ni/SiO₂-8Al₂O₃催化剂表现出最高的乙酰丙酸加氢活性,在180℃、4 MPa氢气压力下,乙酰丙酸转化率达到90.5%,目标产物γ-戊内酯选择性为100%.     

固体电解质La2-xCaxMo1.7W0.3O9-δ(0≤x≤0.2)的合成、表征及电性能

在氧离子导体La₂Mo_1.7W_0.3O₉的基础上，采用固相法合成了La位掺杂的Ca系列新型氧化物La_2-xCa_xMo_1.7W_0.3O_9-δ(0≤x≤0.2)。通过XRD、Raman和XPS等手段对化合物结构进行表征，交流阻抗谱测试其电性能。结果表明：掺杂离子Ca²⁺的半径小于基质离子La³⁺的半径导致晶格收缩；Ca的掺杂在La₂Mo_1.7W_0.3O₉自身内置氧空位的基础上增加了额外的氧空位，提高了氧离子导体的电导率，550 ℃电导率由0.79 × 10^-4 S·cm^-1 (x=0.0)增加到1.5 × 10^-4 S·cm^-1 (x=0.16，0.2)，电导率增加89.9%。     

添加碳元素合成化学计量比LiNiO2

本文采用添加碳元素、葡萄糖及使用多种试剂为原料的合成方法,合成了具有化学计量比的LiNiO2.分析了这些方法在合成反应中的作用,同时给出了合成LiNiO2的最佳反应条件.     

Ultrasound‐Assisted Synthesis of 6‐Methyl‐1,2,3,4‐tetrahydro‐N‐aryl‐2‐oxo/thio‐4‐arylpyrimidine‐5‐carboxamides Catalyzed by Uranyl Nitrate Hexahydrate

An efficient and simple method developed for the synthesis of 6‐methyl‐1,2,3,4‐tetrahydro‐N‐aryl‐2‐oxo/thio‐4‐arylpyrimidine‐5‐carboxamide derivatives ( 4a‐o ) using UO₂(NO₃)₂.6H₂O catalyst under conventional and ultrasonic conditions. The ultrasound irradiation synthesis had shown several advantages such as milder conditions, shorter reaction times and higher yields. The structures of all the newly synthesized compounds have been confirmed by FT‐IR, ¹H NMR, ¹³C NMR and mass spectra.     

Sodium Hydrogen Sulfate as Effective and Reusable Heterogeneous Catalyst for the One-pot Preparation of 14H-[(Un)substituted phenyl]-dibenzo[a,j]xanthene Leuco-dye Derivatives

NaHSO₄•H₂O has been used as an efficient catalyst for the one-pot preparation of 14H-[(un)substituted phenyl]-dibenzo[a,j]xanthene leuco-dye derivatives by condensation of β-naphthol with substituted benzaldehydes under microwave and thermal conditions. This method has the advantages of high yields, a green reaction, an efficient and cost-effective method, simple procedures, short reaction time, and easy workup.     

Green and rapid synthesis of dihydropyrimido [4,5‐b]quinolinetrione derivatives using CoFe2O4@PPA as high efficient solid acidic catalyst under ultrasonic irradiation

A new high efficient and green protocol for the preparation of dihydropyrimido[4,5‐b]quinolinetrione derivatives using magnetically solid acid catalyst was presented. High performance solid acid catalyst was prepared through a three‐step reaction. Firstly, CoFe₂O₄ nano particles were synthesized using co‐precipitation method. In second step, CoFe₂O₄ nano particles were coated with SiO₂ shell through treatment with tetraethyl orthosilicate (CoFe₂O₄@SiO₂). Finaly, CoFe₂O₄@SiO₂ was modified with polyphosphoric acid (CoFe₂O₄@SiO₂/PPA) in a simple manner. Green reusable catalyst was characterized in details using FTIR, VSM, TEM, FESEM, EDX and used as catalyst for the synthesis of dihydropyrimido[4,5‐b]quinolinetrione derivatives. Reaction was performed under ultrasonic irradiation as green, effective and mild conditions and products were achieved in high to excellent yields. Green and eco‐friendly conditions, short reaction times with high yield of products in addition to easy workup are some merits of presented method.     

Reaction in Dry Media: Silica Gel Supported Ferric Chloride Catalyzed Synthesis of 1,8-Dioxo-octahydroxanthene Derivatives

Herein, we describe a green procedure for the one-pot preparation of 1,8-dioxo-octahydroxanthene derivatives by condensation of dimedone and substituted benzaldehydes in the presence of FeCl ₃ -SiO ₂ as an efficient and heterogeneous catalyst under microwave irradiation and thermal conditions. This method has the advantages of high yields, cleaner reactions, efficient and cost-effective method, simple methodology, short reaction times, easy workup, and greener conditions.     

Suppression of the Charge Density Wave State in Two‐Dimensional 1T‐TiSe2 by Atmospheric Oxidation

Two‐dimensional (2D) metallic transition‐metal dichalcogenides (TMDCs), such as 1T ‐TiSe₂, have recently emerged as unique platforms for exploring their exciting properties of superconductivity and the charge density wave (CDW). 2D 1T ‐TiSe₂ undergoes rapid oxidation under ambient conditions, significantly affecting its CDW phase‐transition behavior. We comprehensively investigate the oxidation process of 2D TiSe₂ by tracking the evolution of the chemical composition and atomic structure with various microscopic and spectroscopic techniques and reveal its unique selenium‐assisting oxidation mechanism. Our findings facilitate a better understanding of the chemistry of ultrathin TMDCs crystals, introduce an effective method to passivate their surfaces with capping layers, and thus open a way to further explore the functionality of these materials toward devices.     

Simple and Efficient Synthesis of 2-Aryl-2,3-Dihydroquinolin-4(1H)-ones Using Silica Chloride as a New Catalyst Under Solvent-Free Conditions

A mild, efficient, and high-yielding method for the synthesis of 2-aryl-2,3-dihydroquinolin-4(1H)-ones from their corresponding 2-amino chalcones using silica chloride (SiO₂Cl) under solvent-free conditions is described. A series of 2-aryl-2,3-dihydroquinolin-4(1H)-ones containing both electron-donating and electron-withdrawing substituents were synthesized.     

(Zn1-xMnx)C2O4·2H2O在空气中的热分解动力学研究

用热分析（TG-DTG/DTA）、X射线衍射（XRD）技术和透射电镜（TEM）研究了固态物质Zn_1-xMn_xC₂O₄•2H₂O在空气中热分解的过程。热分析结果表明，Zn_1-xMn_xC₂O₄•2H₂O在空气中分两步分解，其失重率与理论计算失重率相吻合。 XRD和TEM结果表明，Zn_1-xMn_xC₂O₄•2H₂O分解的最终产物为Zn_1-xMn_xO,其颗粒大小约为10-13 nm。在非等温条件下对Zn_1-xMn_xC₂O₄•2H₂O的热分解动力学进行了分析。用Friedman法和Flynn-Wall-Ozawa(FWO)法求取了分解过程的活化能E，并用多元线性回归给出了可能的机理函数。Zn_1-xMn_xC₂O₄•2H₂O两步热分解的活化能分别为155.7513 kJ/mol 和215.9397 kJ/mol。     

An Efficient Procedure for the Synthesis of Benzoxazole and Benzothiazole Derivatives Using a H2O2/SiO2-FeCl3 System

A series of benzoxazole and benzothiazoles was readily prepared from the reaction of ortho-aminophenol/ortho-aminothiophenol and aldehydes using solid silica supported ferric chloride (SiO₂-FeCl₃) as catalyst followed by oxidation with H₂O₂ under ambient conditions. Some of advantages of this method are a simple and convenient procedure, easy purification, and shorter reaction times.

Supplemental materials are available for this article. Go to the publisher's online edition of Phosphorus, Sulfur, and Silicon and the Related Elements to view the free supplemental file.