γ射线及质子辐照导致CCD光谱响应退化的机制

光谱响应是表征CCD性能的重要参数。为了研究辐射环境对CCD光谱响应产生影响的规律及物理机制,开展了不同粒子辐照实验,对CCD光谱响应曲线的退化形式及典型波长下CCD光响应的退化情况进行了分析。辐射效应对CCD光谱响应的影响可以分为电离总剂量效应和位移效应导致的退化,本文从这两种辐射效应出发,采用⁶⁰Co-γ射线及质子两种辐照条件,研究了CCD光谱响应的退化规律。针对460 nm（蓝光）和700 nm（红光）等典型CCD光响应波长,从辐射效应导致的损伤缺陷方面分析了CCD光谱响应退化的物理机制。研究发现,在⁶⁰Co-γ射线辐照时CCD光谱响应曲线变化是由于暗信号增加导致的,而质子辐照导致CCD对700 nm波长的光响应退化明显大于460 nm波长的光响应,且10 MeV质子导致的损伤比3 MeV质子更明显,表明位移损伤缺陷易导致CCD光谱响应退化。结果表明,电离总剂量效应主要导致CCD光谱响应整体变化,而位移效应则导致不同波长光的响应差异增大。     

光谱成像仪快速光谱定标方法研究

光谱定标是确定光谱仪器各通道中心波长的过程,为了获取光谱辐亮度,通常需要对光谱仪器进行辐射定标,将光谱仪器输出的数值,映射为物理量——辐亮度。不同的光谱仪器的光谱响应不同,因此还需要在光谱定标过程中确定各个通道的光谱响应。光谱成像仪可以看成是多个光谱仪组成的,需要对所有点的中心波长和光谱响应进行定标。自第一台成像光谱仪诞生以来,其定标方法逐渐固定,通常需要采用光谱分辨率较光谱成像仪更高的单色仪输出准单色光进行光谱定标,其准单色光的光谱带宽远小于光谱成像仪的光谱响应带宽,可以将准单色光抽象为脉冲函数。根据脉冲函数的特性,改变准单色光的波长,扫描光谱成像仪的响应波长范围,是对光谱响应函数进行间隔采样的过程,通过光谱定标数据可以直接得到光谱成像仪的中心波长和光谱响应函数。随着技术的发展,探测器的灵敏度越来越高,光谱成像仪的分辨率也越来越高,为了完成光谱定标,对光谱定标需要的准单色光提出了更高的要求。然而准单色光的带宽越窄,其能量越低,获取满足信噪比要求的数据需要更长的时间,使定标的效率降低。从光谱定标的目的出发,结合准单色光和光谱成像仪光谱响应近似高斯函数的特点,通过理论分析,提出一种利用宽带定标光进行光谱定标的方法,可以有效减少光谱定标的步骤,提高定标的效率,适用于光谱成像仪的快速定标。该方法用于某星载高光谱成像仪的光谱定标,待标定光谱成像仪采用棱镜分光,具有色散非线性的特点,光谱分辨率在2~18 nm之间变化,同时存在较大的谱线弯曲,导致每个像元的中心波长都不同,需要对每个像元进行光谱定标。为了避免分视场定标导致的相邻视场中心波长不连续现象,将单色仪发出的准单色光的光斑照亮整个狭缝,狭缝和单色仪之间放置柱透镜和毛玻璃,其中柱透镜用于汇聚垂直于狭缝方向的光线,提高能量利用率;毛玻璃用于匀化光照,毛玻璃的存在极大地减弱了进入光谱成像仪的能量,结合提出的方法,增加定标光的带宽,提高能量,最终完成了该光谱成像仪的快速定标,利用汞灯的特征光谱验证该成像光谱仪的光谱定标精度为0.23 nm。     

实验教学用简易光谱仪的研制

研制了实验教学用简易光谱仪,分光器件用全息光栅和棱镜构成,使各波长衍射光成像在CCD平面上不同位置,显示器显示出光谱线和光强曲线.整机体积小,精度较高.利用已知单色光波长进行光谱仪定标,建立(横坐标)像素坐标与被测光波长(纵坐标)之间的函数关系,采用假设性检验法求出测量单色光波长的置信区间.     

空穴在动量空间分布对p型量子阱红外探测器响应光谱的影响

通过对p型量子阱红外探测器(QWIP)的自洽计算，得到了量子阱价带的电子结构和器件的光电流谱，并研究了载流子在动量空间分布对p型QWIP光谱响应的影响.计算结果表明，在动量空间不同区域的空穴对器件的光谱响应起着不同作用，从而使得在p型QWIP中，空穴浓度和温度都将影响器件的响应光谱.所得结果合理地解释了实验中器件响应光谱随掺杂浓度和温度的变化. 关键词： p型量子阱红外探测器 响应光谱 空穴浓度 温度     

BRD96N光调制吸收增强现象的实验研究

通过光谱响应特性实验和记录／读出图像实验，研究了基因变异型细菌视紫红质（BR_D96N）分子膜对单色光的光调制特性.发现BR_D96N分子膜在550nm—600nm范围内对调制光有吸收增强的现象，且对此范围内不同波长的单色光其调制程度有差异.利用曲线拟和方法发现550nm—600nm吸收增强的变化过程分为快过程和慢过程，其对应的时间常数分别为30s和5min.利用强度调制器的吸收强度与图像灰度之间的关系，分析了560nm—600nm范围内出现图像反转的实验现象. 关键词： 细菌视紫红质D96N分子膜 光谱响应 吸收增强现象 图像反转现象     

基于磁流体填充微结构光纤的温度特性研究

利用毛细现象将磁流体完全填充到六角形微结构光纤的空气孔中, 分析了磁流体填充长度、浓度对其传导特性的影响. 结合磁流体独特的热光效应, 并对一定浓度、长度下填充的光纤进行了温度特性的研究. 结果表明, 随着温度的升高, 透射谱1460 nm处磁流体的吸收峰逐渐变浅. 基于磁流体载液与表面活性剂对温度的不同敏感性, 吸收峰左右两个边沿表现出不同的温度响应; 在波长为1100–1700 nm之间透射损耗与温度变化成线性关系, 对于填充长度为10 cm的微结构光纤, 敏感度达到0.06 dB/℃, 且液体填充长度越长, 灵敏度越高. 该研究将微结构光纤与磁流体材料有机地结合起来, 并利用填充材料自身的热光特性, 实现了对透射谱的单边调谐, 将其作为热光可调谐器件、滤波器等相关可调谐光子器件在光通信、 光传感等领域将具有很大的应用潜力. 因此, 基于材料填充微结构光纤的研究可为探索新型全光纤光子器件的新技术和新结构提供有效的方法. 关键词： 微结构光纤 磁流体 热光效应 温度传感     

BR—D96N光存储读出特性的实验研究

细菌视紫红质（bacteriorhodopsin，简称BR）是嗜盐菌细胞膜内的一种光敏蛋白质。BR薄膜材料具有优异的光循环特性和光致变色特性，可作为信息存储材料。本文讨论了BR所记录图像的对比度与读出光波长变化之间的关系。实验中利用YAG激光器二倍频532nm激光作为图像记录光，白光光源通过单色仪选出单色光作为图像读出光，观察BR膜所记录图像对比度随读出光波长变化趋势，并利用图像灰度积分的方法得到记录图像对比度变化曲线。读出光在470nm-620nm波长范围内，读出为正像；460nm波长附近，图像消失；380nm-450nm波长范围内，图像出现反转。     

基于SOA和级联取样光纤光栅的多波长激光器

研究了基于半导体光放大器(SOA)和双段级联取样光纤光栅构成的新型结构多波长激光器.设 计了取样光纤光栅，计算了其反射谱，模拟了多波长激光器的输出光谱.基于自行制作的SOA 和取样光纤光栅，进行了多波长激光器的实验研究，得到了间隔为0.8nm、输出功率不平坦 度小于1.0dB的11个波长输出.理论和实验两个方面都可以验证：与基于普通取样光栅的多波 长方案相比，基于双段级联取样光栅的方案能改善输出谱平坦度，并可提高可激射波长数. 关键词： 半导体光放大器 取样光纤光栅 多波长激光器     

PtSi IRCCD器件用长焦距Si微透镜阵列的制作研究

为了改善PtSi IRCCD器件的红外响应特性,需要添加长焦距微透镜阵列进行焦平面集光,本文提出了一种新的方法—曲率补偿法用于长焦距微透镜阵列的制作.扫描电子显微镜(SEM)显示微透镜阵列为表面极为平缓的方底拱形阵列,表面探针测试结果显示用曲率补偿法制作的微透镜阵列表面光滑,单元重复性好,其焦距可达到685.51μm.微透镜阵列器件与PtSi IRCCD器件在红外显微镜下对准胶合,显著改善了IRCCD器件的光响应特性.     

AlInGaAs/AlGaAs垂直腔面发射激光器温度特性的对比研究

通过测量、对比材料生长和器件制备条件基本相似，但是谐振腔腔模波长与增益峰值波长相对位置明显不同的两类氧化物限制型应变AlInGaAs/AlGaAs量子阱垂直腔面发射激光器(VCSEL)在261—369K温度范围内输出光功率-电流的变温曲线，同时结合测试得到的两类样品的白光反射谱、光荧光谱以及模拟计算得到的不同温度下VCSEL反射谱和增益谱，分析了输出光功率、阈值电流、斜率效率和激射波长随温度变化的关系，掌握了新材料AlInGaAs的温度特性，得到了谐振腔腔模波长和增益峰值波长的相对位置对VCSEL输出特性，尤其是对阈值的影响规律，指出获得室温工作阈值最低且稳定的VCSEL的一个方法是调整谐振腔腔模波长和增益峰值波长的相对位置，并利用这种方法获得了特征温度T₀=333K的AlInGaAs/AlGaAs量子阱VCSEL器件. 关键词： AlInGaAs 垂直腔面发射激光器 特征温度     

微通道板近紫外量子效率测量及成像研究

提出了一种通过测量微通道板输出电流及增益来计算光电流,从而测量出微通道板量子效率的方法,并用该方法测量了微通道板在近紫外(200~380nm)的量子效率.测量结果表明,微通道板的量子效率很低,并且随波长增加而快速下降,200nm波长处的量子效率为10-4数量级,320nm波长处的量子效率为10-8数量级,大于340nm波长处的量子效率极低且趋近于零.微通道板及荧光屏组成的成像器件可以对酒精灯火焰成像,但图像较稀疏,而传统Cs2Te光电阴极紫外成像器件的图像却较密实,这与微通道板量子效率低,Cs2Te光电阴极量子效率高的情形一致.在该成像器件的前端放置一片350nm波长的高通滤光片后,所成的酒精灯火焰图像消失.对被照射目标成像时,如果照射光源为254nm的汞灯,则可以成像;但如果照射光源为365nm汞灯,则不能成像.说明微通道板的光谱响应主要在350nm波长以下,与其量子效率的测量结果一致.最后测量得到该成像器件的分辨力为32lp/mm,与传统Cs2Te光电阴极紫外成像器件的分辨力相同.微通道板及荧光屏组成的成像器件由于不使用光电阴极,具有价格低、寿命长且可靠性高的优点,因此可在紫外信号较强或成像距离较短的条件下使用.     

水听器线列阵近场声压测量误差实验研究

本文介绍了用于近场声压的测量水听器中阵元水听器测量声压的可靠性检验方法和实验结果,提出了元水听器测量球面波场中声传播衰减的曲线与现想球面波声场中场传播衰减的曲线对比的检验,要用球面声源声中心测量值对收发距离进行修正的方法,实验水池中对线列阵上十元水吸器在球形声源水池中进行了传播衰减曲线的测量分析,验证了基阵的弱散散射性能,表明线阵可用于距离小至1／7波长的极近场的扫描测量。     

半波长管传声损失分析*

1/4波长管和Herschel-Quincke(HQ)管具有良好消声潜力,在其固有频率附近具有很高的消声量级,为了将这种消声潜力在更小的安装空间内和更宽的频带上发挥出来,设计了一种新的半波长管,通过对多管传声损失理论模型的推导,运用数值计算的方法,分析了传声损失的影响因素并对多分支管模型进行宽频带尺寸设计,最终实现在350～1350 Hz的宽频带的消声效果,并且通过实验验证了理论模型,同时利用实验数据对管端进行修正,结果证实了理论是正确的。所设计的多分支半波长管可以在复杂的应用场景进行灵活的结构设计,所以在航空发动机降噪、汽车尾气降噪和工厂排气降噪等领域具有更好的适应性和良好的应用前景。     

Comprehensive electro-optical analysis of long wavelength GaInNAs edge-emitting laser diode

Comprehensive analysis of GaInNAs edge-emitting laser operating near 1300 nm wavelength are made to underline the behavioural features of the proposed laser device, in view of the analytical investigation for various material and device electrical-optical parameters analysis such as band diagram, material gain, quantum well emission wavelength, optical wave and mode profiles, light-current-voltage characteristic, output mode spectrum, current distribution and far-field profile. The material analysis indicates that a high quality GaInNAs active region is designed, where high material gain and photoluminescence wavelength near 1.3 μm are achieved. The device obtains low threshold current operation with lasing emission around 1.285 μm.     

Extremely wide band Rayleigh resonant reflector with sharp angular spectra in near infrared wavelength band

In this paper, we propose an extremely broadband Rayleigh resonant reflector with sharp angular spectra operating in near infrared wavelength band, this device consisting of a single germanium resonant grating layer is designed and analyzed by using with the rigorous vector diffraction theory. At the Rayleigh angle, the first diffracted order can be appear from evanescent to a propagating one, thus, a very sharp angular spectrum characteristics can be presented in the device. Based on the guided mode resonant effect, high index material such as silicon and germanium can be designed as wide band reflector, beam splitter and polarizer in near infrared wavelength region. Through connecting Rayleigh phenomena and guided mode resonant effect, we can design a new kind of optical devices with versatile characteristics such as sharp angular spectra and extremely wide reflection band. In this paper, we present a Rayleigh resonant reflector with extremely high reflection (R > 99.5%) for TE polarization light over ∼600 nm wavelength range and sharp angular spectral distribution. In addition, it is shown from our calculations that the high-index nano-layer located adjacent to the substrate is seen to critically affect the resulting spectra of Rayleigh resonant reflector.     

Flattop all-fiber wavelength interleaver for DWDM transmission: Design analysis, parameter optimization, fabrication and characterization recipe

Flattop response within the passband is an important desirable feature of any wavelength selective component that goes into a DWDM optical network. In this paper, we report design and fabrication recipe for realizing wavelength interleavers/slicers with flattop wavelength response, configured around unbalanced all-fiber 2-stage Mach-Zehnder interferometers (MZI). Based on a comprehensive analysis, we have developed a design process/algorithm to determine the optimum splitting ratios as well as the relationship between the splitting ratios of the couplers that constitute the 2-stage MZI, to achieve a flattop wavelength response. The implication of the second delay line with respect to its presence in the upper/lower arm of the second stage of the MZI is highlighted through an algebraic analysis. This revealed that there would be corresponding changes in the optimum splitting ratios of the couplers. These features of our design analysis were then exploited to fabricate a wavelength interleaver with a near box-like response, which validated our algorithm. The polarization dependent losses of the device were measured to be ≈ 0.4 dB. Our analysis and fabrication recipe should be useful in the realization of flattop all-fiber wavelength interleavers for deployment in DWDM networks of high spectral efficiency.     

基于多模二极管激光吸收光谱的氧气浓度测量

可调谐二极管激光吸收光谱技术(TDLAS)具有高灵敏度、高选择性和快速响应等特点,被广泛应用于环境监测、工业生产监控和生物医疗等众多领域。为克服传统TDLAS技术成本高以及长时间工作过程中由于中心波长偏移造成的稳定性差等问题,提出了利用多模二极管激光关联光谱和谐波检测技术实现氧气浓度在线监测的研究。以Fabry-Perot(FP)激光器为光源,通过对760 nm附近氧气分子的多条吸收谱线的探测,实现了对氧气浓度的测量。输出光束被分光系统分成两路信号,分别经过样品池和测量池,双路接收采集含有气体浓度信息的光信号送后级处理,通过测量信号和参考信号之间的相关性及比例关系对氧气浓度进行反演,其中关联光谱技术和谐波检测技术被用于提高系统稳定性和信噪比。结果表明,在1个大气压条件下,系统的探测极限为280 ppm·m,对同一样品在30 min内的30次连续测量的标准偏差为0.056%,表明了系统良好的稳定性。该系统在软、硬件上的设计可以满足氧气的在线监测,且系统稳定性高、装置简单、易用,便于复杂环境应用。     

Modelling of particle paths passing through an ultrasonic standing wave

Within an ultrasonic standing wave particles experience acoustic radiation forces causing agglomeration at the nodal planes of the wave. The technique can be used to agglomerate, suspend, or manipulate particles within a flow. To control agglomeration rate it is important to balance forces on the particles and, in the case where a fluid/particle mix flows across the applied acoustic field, it is also necessary to optimise fluid flow rate. To investigate the acoustic and fluid forces in such a system a particle model has been developed, extending an earlier model used to characterise the 1-dimensional field in a layered resonator. In order to simulate fluid drag forces, CFD software has been used to determine the velocity profile of the fluid/particle mix passing through the acoustic device. The profile is then incorporated into a MATLAB model. Based on particle force components, a numerical approach has been used to determine particle paths. Using particle coordinates, both particle concentration across the fluid channel and concentration through multiple outlets are calculated. Such an approach has been used to analyse the operation of a microfluidic flow-through separator, which uses a half wavelength standing wave across the main channel of the device. This causes particles to converge near the axial plane of the channel, delivering high and low particle concentrated flow through two outlets, respectively. By extending the model to analyse particle separation over a frequency range, it is possible to identify the resonant frequencies of the device and associated separation performance. This approach will also be used to improve the geometric design of the microengineered fluid channels, where the particle model can determine the limiting fluid flow rate for separation to occur, the value of which is then applied to a CFD model of the device geometry.     

Highly Efficient Excitation of Surface Plasmons Using a Si Gable Tip

A compact and highly efficient technique to excite SPP mode at an Au/SiO₂ interface by using an engineered high index (silicon) gabled tip at the 1550 nm wavelength has been proposed. The optimized geometry of the Si tip enables a highly efficient excitation of the single interface SPP mode through near field interaction in an ultra‐compact setup. An experimental demonstration of the proposed scheme is also presented in the paper which converts 25.5% of the total input power to an SPP mode. With an improved fabrication, this efficiency can reach as high as 52%. The device is compact, facilitates on‐chip excitation of the SPP, its fabrication is compatible with the standard Si fabrication processes, and, as such it is expected to be very useful in the design of future integrated photonic circuits as well as integrated sensors. Also, this scheme can find applications in studying nonlinear characteristics of materials.     

Standing Friedel waves: a quantum probe of electronic states in nanoscale devices

We report a theoretical study of the dynamic response of electrons in a metallic nanowire or a two-dimensional electron gas under a capacitively coupled "spot gate" driven by an ac voltage. A dynamic standing Friedel wave (SFW) is formed near the spot gate and near edges and boundaries, analogous to the static Friedel oscillations near defects. The SFW wavelength is controlled by the ac voltage frequency and the device's Fermi velocity, whereby the latter can be measured. In addition, the SFW amplitude exhibits resonant behavior at driving frequencies that are related to eigenenergy spacings in the device, allowing their direct measurement.