基于Cu/SiO_x/Al结构的阻变存储器多值特性及机理的研究

采用氧化硅材料构建了Cu/SiOx/Al的三明治结构阻变存储器件.用半导体参数分析仪对其阻变特性进行测量,结果表明其具有明显的阻变特性,并且通过调节限制电流,得到了四个稳定的阻态,各相邻阻态的电阻比大于10,并且具有良好的数据保持能力.在不同温度条件下对各个阻态进行电学测试及拟合,明确了不同阻态的电子传输机理不尽相同:阻态1和阻态2为欧姆传导机制,阻态3为P-F(Pool-Frenkel)发射机制,阻态4为肖特基发射机制.根据电子传输机制,建立了铜细丝导电模型并对Cu/SiOx/Al阻变存储器件各个阻态的电致阻变机制进行解释.     

Ni/HfO_2/Pt阻变单元特性与机理的研究

研究了Ni/HfO2(10 nm)/Pt存储单元的阻变特性和机理.该器件具有forming-free的性质,还表现出与以往HfO2(3 nm)基器件不同的复杂的非极性阻变特性,并且具有较大的存储窗口值(105).存储单元的低阻态阻值不随单元面积改变,符合导电细丝阻变机理的特征.采用X射线光电子能谱仪分析器件处于低阻态时的阻变层HfO2薄膜的化学组分以及元素的化学态,结果表明,Ni/HfO2/Pt阻变存储器件处于低阻态时的导电细丝是由金属Ni导电细丝和氧空位导电细丝共同形成的.     

铜掺杂氧化锌薄膜阻变特性的研究

以 ZnO：Al为底电极,Cu为顶电极,在同种工艺条件下分别制备了类电容结构的纯ZnO 阻变器件和ZnO：2%Cu阻变器件,分析比较了两种器件的典型I-V特性曲线、置位电压（V_Set）和复位电压（V_Reset）的分布范围、器件的耐久性。结果显示,ZnO：Cu阻变器件较纯ZnO阻变器件有更大的开关比和更稳定的循环性能。另外,研究了 ZnO：Cu阻变器件的阻变机理,通过对其I-V特性曲线分析得出以下结论：ZnO：Cu阻变器件在高阻态遵循空间电荷限制电流效应,低阻态符合欧姆定律。     

Ti/HfO2/Pt阻变存储单元中的氧空位聚簇分布

为了研究阻变存储器导电细丝的形成位置和分布规律, 使用X射线光电子能谱研究了Ti/HfO₂/Pt阻变存储器件单元中Hf 4f的空间分布, 得到了阻变层的微结构信息. 通过I-V测试, 得到该器件单元具有典型的阻变特性; 通过针对Hf 4f的不同深度测试, 发现处于低阻态时, 随着深度的增加, Hf⁴⁺化学组分单调地减小; 而处于高阻态和未施加电压前, 该组分呈现波动分布; 通过Hf⁴⁺在高阻态和低阻态下组分含量以及电子能损失谱分析, 得到高阻态下Hf⁴⁺组分的平均含量要高于低阻态; 另外, 高阻态和低阻态下的O 1s谱随深度的演变也验证了Hf⁴⁺的变化规律. 根据实验结果, 提出了局域分布的氧空位聚簇可能是造成这一现象的原因. 空位簇间的链接和断裂决定了导电细丝的形成和消失. 由于导电细丝容易在氧空位缺陷聚簇的地方首先形成, 这一研究为导电细丝的发生位置提供了参考.     

阻变式存储器存储机理

阻变式存储器(resistive random access memory,RRAM)是以材料的电阻在外加电场作用下可在高阻态和低阻态之间实现可逆转换为基础的一类前瞻性下一代非挥发存储器.它具有在32nm节点及以下取代现有主流Flash存储器的潜力,成为目前新型存储器的一个重要研究方向.但阻变式存储器的电阴转变机理不明确,制约它的进一步研发与应用.文章对阻变式存储器的体材料中几种基本电荷输运机制进行了归纳,总结了目前对阻变式存储器存储机理的理论模型.     

基于ITO/聚甲基丙烯酸甲酯/Al的有机阻变存储器SPICE仿真

探索了ITO/PMMA/Al器件的阻变机理及其SPICE电路仿真, 通过优化聚甲基丙烯酸甲酯(PMMA)层退火温度, 器件可实现连续擦-读-写-读操作. 基于不同退火温度PMMA薄膜的表面形貌研究, 构建了单层有机阻变器件的非线性电荷漂移模型, 以及描述该模型掺杂区界面移动的状态方程, 并通过反馈控制积分器建立了SPICE仿真电路. 最后, 代入器件实际测量参数, 得到与器件实际结果基本一致的电流-电压模拟曲线. 结果验证了单层有机器件的阻变机理, 说明该非线性电荷漂移模型的SPICE仿真在有机阻变器件仿真中同样适用. 关键词： 有机阻变存储器 非线性电荷漂移 SPICE仿真     

电泳沉积法制备的Zn1-xCxO薄膜的结构及阻变性能

采用电泳沉积法在FTO导电玻璃基片上制备Zn_1-xCu_xO薄膜,并对其微观结构、光致发光谱、伏安特性、保持特性和转换电压分布进行探讨。PL谱表明,Cu掺杂在禁带中引入深受主能级,降低氧空位浓度,导致ZnO薄膜的紫外发光、蓝光发光和绿光发光峰强度降低。所得薄膜的晶粒细小、致密、均匀,具有稳定的双极性阻变特性,开关比R_off/R_on最高达到10⁵,其低阻态（LRS）和高阻态（HRS）的阻变机理分别符合欧姆定律和空间电荷限制传导理论。器件经100次循环测试后开关比无明显变化,呈现出较为良好的抗疲劳特性。Cu掺杂对LRS影响不大,但显著改善了HRS的分散性以及转换电压V_SET的分散性。当Cu掺杂量x=0.04时,器件表现出良好的综合性能：R_off≈10⁶ Ω,R_off/R_on≈10⁴,V_SET介于0.4~3.03 V之间。     

基于果胶材料的阻变存储器离子缓冲层研究

采用微波辅助法制备了生物果胶薄膜,并作为缓冲层,制作了Ag/pectin/a-C/Pt阻变存储器.利用原子力显微镜表征薄膜表面的电流分布,探究了果胶薄膜的离子缓冲机理.分析了基于果胶薄膜的阻变存储器的阻变性能和阻变机制.结果表明:该缓冲层能够降低器件开关电压的波动性,提升高低阻态开关比.通过调控限制电流,在单一器件上实现了多阻态信息存储.     

基于HfO2的阻变存储器中Ag导电细丝方向和浓度的第一性原理研究

采用基于密度泛函理论的第一性原理方法, 研究了基于HfO₂的阻变存储器中Ag 导电细丝浓度以及方向性. 通过计算Ag杂质5种方向模型的分波电荷态密度等势面图、形成能、 迁移势垒和分波电荷态密度最高等势面值, 发现[-111]方向最有利于Ag导电细丝的形成, 这对器件的开启电压、形成电压和开关比有很大影响. 本文基于最佳的[-111]导电细丝方向, 设计了4 种Ag 浓度结构. 计算4种Ag浓度结构的分波电荷态密度等势面图, 得出Ag浓度低于4.00 at.% 时晶胞结构中无导电细丝形成且无阻变现象. 当Ag浓度从4.00 at.%增加到4.95 at.% 时, 晶胞结构中发现有导电细丝形成, 表明Ag浓度高于4.00 at.%时, 晶胞中可以发生阻变现象. 然而, 通过进一步对比计算这两种晶胞结构中Ag的形成能、分波电荷态密度最高等势面值、总态密度与Ag的投影态密度发现, Ag浓度越大, 导电细丝却不稳定, 并且不利于提高阻变存储器的开关比. 本文的研究结果可为改善基于HfO₂的阻变存储器的性能提供一定理论指导.     

基于Au/TiO_2/FTO结构忆阻器的开关特性与机理研究

采用简单的一步水热法在FTO导电玻璃上外延生长了锐钛矿TiO_2纳米线,制备了具有Au/TiO_2/FTO器件结构的锐钛矿TiO_2纳米线忆阻器,系统研究了器件的阻变开关特性和开关机理.结果表明,Au/TiO_2/FTO忆阻器具有非易失的双极性阻变开关特性.同时,在103s的时间内,器件在0.1 V的电阻开关比始终保持在20以上,表明器件具有良好的非易失性.此外,器件在低阻态时遵循欧姆导电特性,而在高阻态时则满足陷阱控制的空间电荷限制电流传导机制,同时提出了基于氧空位导电细丝形成与断开机制的阻变开关模型.研究结果表明Au/TiO_2/FTO忆阻器将是一种很有发展潜力的下一代非易失性存储器.     

Charge transport and bipolar switching mechanism in a Cu/HfO_2/Pt resistive switching cell

Bipolar resistance switching characteristics are investigated in Cu/sputtered-HfO_2/Pt structure in the application of resistive random access memory(RRAM).The conduction mechanism of the structure is characterized to be SCLC conduction.The dependence of resistances in both high resistance state(HRS) and low resistance state(LRS) on the temperature and device area are studied.Then,the composition and chemical bonding state of Cu and Hf at Cu/HfO_2 interface region are analyzed by x-ray photoelectron spectroscopy(XPS).Combining the electrical characteristics and the chemical structure at the interface,a model for the resistive switching effect in Cu/HfO_2/Pt stack is proposed.According to this model,the generation and recovery of oxygen vacancies in the HfO_2 film are responsible for the resistance change.     

Any-polar resistive switching behavior in Ti-intercalated Pt/Ti/HfO2/Ti/Pt device

The special any-polar resistive switching mode includes the coexistence and stable conversion between the unipolar and the bipolar resistive switching mode under the same compliance current. In the present work, the any-polar resistive switching mode is demonstrated when thin Ti intercalations are introduced into both sides of Pt/HfO₂/Pt RRAM device. The role of the Ti intercalations contributes to the fulfillment of the any-polar resistive switching working mechanism, which lies in the filament constructed by the oxygen vacancies and the effective storage of the oxygen ion at both sides of the electrode interface.     

Analysis of the resistive switching behaviors of vanadium oxide thin film

We demonstrate the polarization of resistive switching for a Cu/VOx/Cu memory cell.The switching behaviors of Cu/VOx/Cu cell are tested by using a semiconductor device analyzer(Agilent B1500A),and the relative micro-analysis of I-V characteristics of VOx/Cu is characterized by using a conductive atomic force microscope(CAFM).The I-V test results indicate that both the forming and the reversible resistive switching between low resistance state(LRS) and high resistance state(HRS) can be observed under either positive or negative sweep.The CAFM images for LRS and HRS directly exhibit evidence for the formation and rupture of filaments based on positive or negative voltage.The Cu/VOx/Cu sandwiched structure exhibits reversible resistive switching behavior and shows potential applications in the next generation of nonvolatile memory.     

过渡金属元素X(X=Mn,Fe,Co,Ni)掺杂对ZnO基阻变存储器性能的影响

实验表明掺杂是一种改善阻变存储器性能的有效手段,但其物理机理鲜有研究.本文采用第一性原理方法系统研究了过渡金属元素X(X=Mn,Fe,Co,Ni)掺杂对ZnO基阻变存储器中氧空位迁移势垒和形成能的影响.计算结果表明Ni掺杂可同时有效降低+1和+2价氧空位在掺杂原子附近的迁移势垒,X掺杂均减小了氧空位的形成能,特别是掺杂Ni时氧空位的形成能减小最为显著(比未掺杂时减少了64%).基于该结果制备了未掺杂和Ni掺杂ZnO阻变存储器,研究表明通过掺杂控制体系中氧空位的迁移势垒和形成能,可以有效改善器件的初始化过程、操作电压、保持性等阻变性能.研究结果有助于理解探究影响阻变的微观机制,并可为掺杂提高阻变存储器性能提供一定的理论指导.     

Investigation of resistive switching behaviours in WO3-based RRAM devices

In this paper, a WO₃-based resistive random access memory device composed of a thin film of WO₃ sandwiched between a copper top and a platinum bottom electrodes is fabricated by electron beam evaporation at room temperature. The reproducible resistive switching, low power consumption, multilevel storage possibility, and good data retention characteristics demonstrate that the Cu/WO₃/Pt memory device is very promising for future nonvolatile memory applications. The formation and rupture of localised conductive filaments is suggested to be responsible for the observed resistive switching behaviours.     

Bipolar switching properties of amorphous TiO2 thin film grown on TiN/Si substrate

Pt/TiO₂/TiN device with the amorphous TiO₂ film grown at room temperature under an oxygen partial pressure of 1.0 mTorr showed reliable bipolar switching behavior. During the electroforming process, a large number of oxygen vacancies formed in the TiO₂ film and accumulated at the Pt/TiO₂ interface. The barrier height of the Schottky contact of the Pt/TiO₂ interface was reduced owing to the presence of these oxygen vacancies, resulting in the low-resistance state (LRS). Moreover, oxygen ions diffused into the TiN electrode during the electroforming and set processes. On the other hand, the oxygen ions in the TiN electrode diffused out and reacted with oxygen vacancies in the TiO₂ film during the reset process, and the device changed from the LRS to the high-resistance state (HRS). Conduction in the LRS and HRS can be attributed to Ohmic conduction and the trap controlled space charged limited mechanism, respectively.     

Analysis of resistive switching behaviors of vanadium oxide thin film

We demonstrated the polarization of resistive switching for Cu/VO_x/Cu memory cell. Switching behaviors of Cu/VO_x/Cu cell were tested by semiconductor device analyzer (Agilent B1500A), and the relative micro-analysis of I-V characteristics of VO_x/Cu was characterized by conductive atomic force microscope (CAFM). The I-V test results indicated that both forming and the reversible resistive switching between low resistance state (LRS) and high resistance state (HRS) can be observed under either positive or negative sweep. The CAFM images for LRS and HRS directly exhibited evidences of the formation and rupture of filaments based on positive or negative voltage. Cu/VO_x/Cu sandwiched structure exhibits a reversible resistive switching behavior and shows potential applications in the next generation nonvolatile memory field.     

Coexistence of nonvolatile unipolar and volatile threshold resistive switching in the Pt/LaMnO3/Pt heterostructures

Coexistence of nonvolatile unipolar and volatile threshold resistive switching is observed in the Pt/LaMnO₃ (LMO)/Pt heterostructures. The nonvolatile unipolar memory is achieved by applying a negative bias, while the volatile threshold resistive switching is obtained under a positive bias. Additionally, the pristine low resistance state (LRS) could be switched to high resistance state (HRS) by the positive voltage sweeping, which is attributed to the conduction mechanism of Schottky emission. Subsequently, the insulator-to-metal transition in the LMO film due to formation of ferromagnetic metallic phase domain contributes to the volatile threshold resistive switching. However, the nonvolatile unipolar switching under the negative bias is ascribed to the formation/rupture of oxygen-vacancy conducting filaments. The simultaneously controllable transition between nonvolatile and volatile resistance switching by the polarity of the applied voltage exhibits great significance in the applications of in-memory computing technology.