新型氯取代含杂萘联苯结构可溶性聚芳酰胺的合成、表征和性能

以类双酚单体4-(3-氯-4-羟基-苯基)-2H-二氮杂萘-1-酮(DHPZ-OC)和对氯苯腈为原料进行亲核取代反应合成二腈化合物4-[3-氯-4-(4-氰基苯氧基)苯基]-2-(4-氰基苯基)二氮杂萘-1-酮(),然后在碱性(KOH)条件下进行水解制得了一种新型的含氯取代杂萘联苯结构的芳香二酸,4-[3-氯-4-(4-羧基苯氧基)苯基]-2-(4-羧基苯基)二氮杂萘-1-酮().用新二酸与各种芳香二胺进行直接缩合聚合制得了一系列新型氯取代含杂萘联苯结构的聚芳酰胺,特性粘度可达1.23dL/g.用FTIR和¹HNMR研究了新型二酸单体及聚合物的结构.该类聚芳酰胺均可溶解于NMP,DMAc和DMSO等极性有机溶剂中,并且可浇铸成透明韧性膜,其玻璃化转变温度在291～332℃之间,10%的热失重温度在460℃以上.     

含3,5-二甲基二氮杂萘酮联苯结构聚醚酰亚胺的合成与性能

由4-[(3,5-二甲基-4-羟基)苯基]-2,3-杂萘-1-酮与4-氯-N-苯基邻苯酰亚胺通过亲核取代反应、水解反应和脱水反应合成了一种新型不对称含二氮杂萘联苯结构的二酐单体,并对其进行结构表征.由新型二酐单体与市售的二胺单体通过“一步法”溶液聚合反应合成了5种含二氮杂萘酮联苯结构的聚醚酰亚胺.通过FTIR和¹HNMR方法研究了聚合物的结构及性能.结果表明,该类聚合物既具有较高的耐热性能,又可以在室温下溶解于非质子极性溶剂,如N-甲基吡咯烷酮和间甲酚等.     

新型萘酰亚胺衍生物的合成

N-(N’,N’-二甲基氨基乙基)-4-硝基-1,8-萘酰亚胺和2,3-二甲基苯并噻唑碘化盐在痕量水存在下经亲核取代反应合成了一个新型的萘酰亚胺衍生物——N-(N’,N’-二甲基氨基乙基)-4-[2-(2,3-二氢-2,3-二甲基苯并噻唑)氧基]-1,8-萘酰亚胺,其结构经1H NMR,13C NMR和ESI-MS表征。并对反应机理进行了初步研究。     

1,8-萘酰亚胺衍生物的设计、合成及其对半胱氨酸的识别研究

巯基氨基酸水平异常与多种疾病相关,其检测仍存在一定的局限,研究检测巯基氨基酸的荧光探针具有一定的价值.以苊为原料合成了61个1,8-萘酰亚胺衍生物,研究了该类化合物的荧光性能及其作为半胱氨酸含量测定的荧光探针的可能性.紫外光谱分析表明1,8-萘酰亚胺衍生物上N-取代基对最大吸收波长无明显影响;荧光光谱(FL)的性能测试显示硝基萘酰亚胺衍生物N-甲基-4-硝基-1,8-萘二甲酰亚胺(4a)～4-硝基-N-间氟苯基-1,8-萘二甲酰亚胺(4s)无荧光,氨基萘酰亚胺衍生物N-甲基-4-氨基-1,8-萘二甲酰亚胺(5a)～4-氨基-N-间氟苯基-1,8-萘二甲酰亚胺(5s)有强烈黄色荧光,而马来酰亚胺萘酰亚胺衍生物N-甲基-4-(1H-吡咯-2,5-二酮-1-基)-1,8-萘二甲酰亚胺(6a)～4-(1H-吡咯-2,5-二酮-1-基)-N-(间氟苯基)-1,8-萘二甲酰亚胺(6s)有微弱蓝色荧光,其中7个马来酰亚胺萘酰亚胺衍生物探针对半胱氨酸(Cys)溶液有荧光点亮效应.对7个探针加入21种其它氨基酸作为干扰项的测试显示探针对半胱氨酸检测有良好的选择性.研究了不同pH值下荧光强度,检测探针与半...     

钴萘酞菁的合成

采用Diels-Alder方法合成了2,3-萘二腈和6,7-二溴-2,3-萘二腈化合物,并以此为前体成功地合成了相应的钴萘酞菁系列化合物---一种新型的功能有机材料。另外还探讨了酞菁形成的机理,并讨论了若干影响因素。这些化合物具有较好的稳定性,在胺类或其它含氮的有机溶剂中有较好的溶解度,如苯胺、二甲基甲酰胺(DMF)或吡啶等。     

AlMCM-48介孔分子筛对萘异丙基化反应的活性

2－烷基萘和2,6－二烷基萘是很有价值的化学品,2－烷基萘可用于染料,药物,香料等精细化学品的生产,2,6－二烷基萘是生产新型聚合材料的重要原料,以煤焦油中萘 原料经傅－克反应可获得烷基萘,工业上传统的液相反应用H2SO4,H4PO4,AlCl3等作催化剂[1],由于存在腐蚀性强,产物分离难,污染重等弊病,人们极力探求性能优良,环境友好的新型催化剂,各种沸石分子筛如ZSM－5,HY,HM,β－沸石等对萘 烷基化反应的催化性能都有探讨^[2-6],据报道,用H－ZSM－5催化萘的甲基反应显示较高的选择性^[2],n(2-甲基萘）／n(1-甲基萘）达到8;（2,6－二甲基萘＋2,7－二甲基萘）在二取代产物中达到80．8％,但萘的转化率较低,约10％,由于H－ZSM－5的孔径较小,它对萘的异丙基化反应几乎无活性[6],HY,Hβ对萘的异丙基化反应活性较高,但选择性差,n(2,6-二甲基萘／2,7－二甲基萘）＝1,HM对萘的异丙基化反应选择性较高,而萘的转化率不高,约30％^[3-6],掺要Ce的丝光沸石选择性和活性都有所提高[7],本文研究了用后处理方法固载铝的AlMCM-48介孔分子筛对萘的异丙基化反应的催化作用,考察了Si/Al对反应的影响。β     

含荧光基团的AA-MA共聚物阻垢剂的合成及其阻垢性能

以4-溴-1,8-萘二甲酸酐和乙二胺为原料,经3步反应合成了一种新型荧光单体——4-甲氧基-N-(2-丙烯酰胺乙基)-1,8-萘二酰亚胺(Ⅲ);Ⅲ与丙烯酸(AA)和马来酸酐(MA)共聚制得新型示踪共聚物AA-MA-Ⅲ(1),其结构经IR,TG-DTA和SEM表征。1的荧光性质和阻垢性能研究结果表明,其荧光强度与质量浓度呈良好线性关系,线性相关系数为0.998 5,检测下限为1.0×10-2mg.L-1;1对碳酸钙垢沉积有较好的抑制作用,当用药量为20 mg.L-1时对碳酸钙阻垢率为93.5%,且具有较好的分散氧化铁的能力;SEM观察表明1对碳酸钙垢既有较强的分散作用又具有明显的晶格畸变作用。     

一类含联二萘结构的新型聚芳醚酮类刚性大环及其二聚体的合成与表征

通过一定的分子设计,利用一种全新的双酚单体(4-氯代苯基对苯二酚)和含有联二萘结构的双氟三聚体(BNDIF)经一步法合成环状齐聚物,制得了一类含有氯代苯基侧基和联二萘结构的新型聚芳醚酮类刚性大环;并通过氯苯基的催化偶联反应得到了该类刚性大环的二聚体(一类含有2个联二萘结构的新型结构双环齐聚物).利用MALDI-TOFMS和1HNMR及H-HCOSY分析,证明了目标产物的结构.     

高Tg含萘聚芳醚酮的合成与性能

利用Friedel-Craft和去醚化反应成功地制备了具有对称取代结构的含萘双酚单体1,5-二(3-甲基)苯羰基-2,6-二羟基萘, 并且通过高温亲核取代反应制得了两种高分子量的芳香族聚合物, 对这两种新型聚合物的热性能、溶解性能、机械性能及介电常数等进行了表征.     

无金属催化快速合成2-芳酰氨基萘并[1,2-d]噻唑

报道了在室温条件下,二醋酸碘苯促进3-[1-(4-取代萘基)]-1-芳酰基硫脲自身关环得到一系列2-芳酰氨基萘并[1,2-d]噻唑衍生物.该方法具有反应条件温和,反应迅速,操作简单,原子利用率高,无需金属催化以及底物范围广等优点.该方法也为萘并[1,2-d]噻唑衍生物的合成提供了新的高效途径.     

高交联大孔苯乙烯/二乙烯苯共聚物的合成及其孔结构的研究Ⅱ

本文对高交联大孔苯乙烯/二乙烯苯共聚物在干态、湿态与溶胀态的孔结构进行了研究。结果表明,在不同的状态中,高交联共聚物的孔结构是不相同的,它们的孔结构会发生变化。但是,它们的孔结构变化远小于低交联共聚物,也就是说,高交联大孔共聚物的孔结构比低交联共聚物的孔结构稳定。 鉴于高交联大孔共聚物的孔结构较稳定,作者把它用作高效液相色谱的进行了初步实验。结果表明,高交联共聚物可做为高效液相色谱的载体固定相。     

Biredox Eutectic Electrolytes Derived from Organic Redox‐Active Molecules: High‐Energy Storage Systems

One promising candidate for high‐energy storage systems is the nonaqueous redox flow battery (NARFB). However, their application is limited by low solubility of redox‐active materials and poor performance at high current density. Reported here is a new strategy, a biredox eutectic, as the sole electrolyte for NARFB to achieve a significantly higher concentration of redox‐active materials and enhance the cell performance. Without other auxiliary solvents, the biredox eutectic electrolyte is formed directly by the molecular interactions between two different redox‐active molecules. Such a unique electrolyte possesses high concentration with low viscosity (3.5 m , for N‐butylphthalimide and 1,1‐dimethylferrocene system) and a relatively high working voltage of 1.8 V, enabling high capacity and energy density of NARFB. The resulting high‐performance NARFB demonstrates that the biredox eutectic based strategy is potentially promising for low‐cost and high‐energy storage systems.     

聚合物在高压下的结构、形态和性能（下）

聚合物在高压下的结构、形态和性能（下）张雄伟，黄锐（成都科技大学塑料工程系，成都，６１００６５）在上篇中我们介绍了结晶性聚合物在高压下结晶的结构和形态。本篇将介绍聚合物在高压下的结晶动力学和热力学以及聚合物在高压下的退火等方面内容。２高压结晶动力学研...     

Extraordinary Supercapacitor Performance of a Multicomponent and Mixed‐Valence Oxyhydroxide

We report a novel multicomponent mixed‐valence oxyhydroxide‐based electrode synthesized by electrochemical polarization of a de‐alloyed nanoporous NiCuMn alloy. The multicomponent oxyhydroxide has a high specific capacitance larger than 627 F cm^?3 (1097±95 F g^?1) at a current density of 0.25 A cm^?3, originating from multiple redox reactions. More importantly, the oxyhydroxide electrode possesses an extraordinarily wide working‐potential window of 1.8 V in an aqueous electrolyte, which far exceeds the theoretically stable window of water. The realization of both high specific capacitance and high working‐potential windows gives rise to a high energy density, 51 mWh cm^?3, of the multicomponent oxyhydroxide‐based supercapacitor for high‐energy and high‐power applications.     

Parallel changes in non-photochemical quenching properties, photosynthesis and D1 levels at sudden, prolonged irradiance exposures in Ulva fasciata Delile

The photosynthetic response to a sudden and prolonged high irradiance exposure and following recovery at low irradiance were studied with the aim of investigating the ability to withstand and adapt to high irradiance without prior high light adaptation. When thalli of Ulva fasciata, accustomed to a low irradiance (80 micromol photons m(-2) s(-1)), were exposed to a high irradiance (1500 micromol photons m(-2) s(-1)), the D1 protein was rapidly degraded, reaching a steady-state level after 110 min. This was followed by a fast recovery when thalli were transferred to dim light. The overall ability of non-photochemical quenching of chlorophyll fluorescence decreased and levelled off at a sudden and prolonged exposure to high irradiance and followed the same trend as the D1 level with a fast recovery in dim light. Ulva had intrinsic means to acclimate rapidly to high irradiance, when non-photochemical quenching did not operate properly, by maintaining a smaller fraction of high light tolerant PSII assemblages and by maintaining a high non-photochemical quenching capacity of chlorophyll fluorescence in relation to the variable fluorescence. The overall absorption of light (400-700 nm) remained high during the period of high irradiance exposure. When Ulva were deprived of nutrients in the form of PES media the ability of non-photochemical quenching decreased at photoinhibitory conditions. The possible causes for the responses at prolonged irradiance and the mechanisms for the decrease of non-photochemical quenching are discussed, with implications for field measurements.     

Phase‐Transition Induced Conversion into a Photothermal Material: Quasi‐Metallic WO2.9 Nanorods for Solar Water Evaporation and Anticancer Photothermal Therapy

Phase transition from WO₃ to sub‐stoichiometric WO_2.9 by a facile method has varied the typical semiconductor to be quasi‐metallic with a narrowed band gap and a shifted Femi energy to the conduction band, while maintaining a high crystallinity. The resultant WO_2.9 nanorods possess a high total absorption capacity (ca. 90.6 %) over the whole solar spectrum as well as significant photothermal conversion capability, affording a conversion efficiency as high as around 86.9 % and a water evaporation efficiency of about 81 % upon solar light irradiation. Meanwhile, the promising potential of the nanorods for anticancer photothermal therapy have been also demonstrated, with a high photothermal conversion efficiency (ca. 44.9 %) upon single wavelength near‐infrared irradiation and a high tumor inhibition rate (ca. 98.5 %). This study may have opened up a feasible route to produce high‐performance photothermal materials from well‐developed oxides.     

Study of dielectric properties of styrene-acrylonitrile graphite sheets composites in low and high frequency region

Conducting polymer composites should have a high dielectric constant and a high dissipation factor in the low and high frequency regions if they are to be used in charge storing devices, decoupling capacitors and electromagnetic interference shielding applications. Currently, extensive research is being carried out to enhance the dielectric constants of graphite-polymer, ceramic powder-polymer, metal powder-polymer and nanotube-polymer composites in the low frequency region. In this paper, we present the dielectric properties of styrene-acrylonitrile (SAN)-graphite sheets (GS) composites in the low and high frequency ranges. SAN-GS composites were prepared by the mixing process and by the hot compression mold technique. The composites showed a high dielectric constant and a high dissipation factor in the low and radio frequency region. Furthermore, the EMI shielding properties of these composites are evaluated in the radio frequency range. The conductivity and the dielectric constant of the SAN/GS composites increased with the addition of GS composites, and followed the power law model of percolation theory. The dielectric constant and the dissipation factor of the composites were analyzed according to the low and high frequency region.     

Synthesis and characterization of alkaline‐soluble triazine‐based poly(phenylene sulfide)s with high refractive index and low birefringence

High‐refractive‐index (high‐n) polymers (HRIPs) with a high optical transparency are highly needed in advanced optoelectronic devices. In this work, we report the synthesis and characterization of a series of high‐n, transparent, totally colorless, and high‐sulfur‐containing poly(phenylene sulfide)s (PPSs) bearing a triazine unit. Two new triazine monomers T1 and T2 with hydroxyl and tert‐butyl acetate side chains, respectively, were designed and synthesized to develop PPSs with high‐n and high alkaline solubility. These PPSs were prepared by the single‐phase polycondensation from T1 / T2 and commercial aromatic dithiols such as 4,4′‐thiobisbenzenethiol ( TBT ) and benzene‐1,3‐dithiol ( BDT ), achieving very high‐n up to 1.7530 at 633 nm, a high optical transparency (T% > 90% @400 nm) and low birefringence (Δn = 0.0014–0.0080), and exhibiting high potential on the application of high‐n photoresists. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 724–731     

Aromatic liquid crystals with a trifluoromethyl group in the terminal chain for use in nematic LC mixtures

A new class of compounds suitable for LCD applications has have synthesized, incorporating a trifluoromethyl group in the terminal alkoxy or alkenyloxy chain. These compounds fulfil many of the specifications for use in TN-LCDs. Compounds containing several aromatic rings were synthesized with a view to producing compounds of high birefringence. This aspect also included the synthesis of compounds containing a carbon-carbon triple bond. Materials with three phenyl rings were also prepared in an attempt to produce nematic liquid crystals with a high clearing point and a high birefringence. Molecules containing a lateral fluoro substituent were synthesized in order to generate a high positive value of the dielectric anisotropy, a low melting point and no smectic mesophases. A series of compounds incorporating a carbon-carbon double bond was prepared in an attempt to produce compounds with a high nematic clearing point and a high birefringence.     

Electrochemical Synthesis of Tetrahexahedral Rhodium Nanocrystals with Extraordinarily High Surface Energy and High Electrocatalytic Activity

Noble metal nanocrystals (NCs) enclosed with high‐index facets hold a high catalytic activity thanks to the high density of low‐coordinated step atoms that they exposed on their surface. Shape‐control synthesis of the metal NCs with high‐index facets presents a big challenge owing to the high surface energy of the NCs, and the shape control for metal Rh is even more difficult because of its extraordinarily high surface energy in comparison with Pt, Pd, and Au. The successful synthesis is presented of tetrahexahedral Rh NCs (THH Rh NCs) enclosed by {830} high‐index facets through the dynamic oxygen adsorption/desorption mediated by square‐wave potential. The results demonstrate that the THH Rh NCs exhibit greatly enhanced catalytic activity over commercial Rh black catalyst for the electrooxidation of ethanol and CO.