Catalysis by Using TiO2 Nanoparticles and Nanotubes

TiO2 has attracted considerable attention due to its stability, non-toxicity, low cost, and great potential for use as a photocatalyst in environmental applications. Since strong metal-support interaction (SMSI) of titania-supported noble metals was first reported in 1978, titania supported catalyst has been intensively studied in heterogeneous catalysis. However, the effective catalytic activity was restricted due to the low surface area of TiO2. Recently, TiO2-based nanotubes were extensively investigated because of their potentials in many areas such as highly efficient photocatalysis and hydrogen sensor.In the present study, formation of titanium oxide (TiO2) nanotubes was carried out by hydrothermal method, with TiO2 nanoparticle-powders immersed in concentrated NaOH solution in an autoclave at 110 ℃. Preparation of nano-size Pt on TiO2-nanoparticles or TiO2-nanotubes was performed by photochemical deposition method with UV irradiation on an aqueous solution containing TiO2 and hexachloroplatinic acid or tetrachloroauric acid. The TEM micrographs show that TiO2-nanotubes exhibit ～300 nm in length with an inner diameter of ～ 6 nm and the wall thickness of ～ 2 nm, and homogeneous nanosize Pt particles (～ 2 nm) were well-dispersed on both nanoparticle- and nanotube- titania supports. It also shows the nanotube morphology was retained up2o n Pt-immobilization. Nitrogen adsorption isotherm at 77K resulted a high surface area (～ 200m/g) of TiO2-nanotubes, which is about 40 times greater than that of "mother" TiO2 nanoparticles (～5 m/g). All the spectroscopic results exhibited that the nanotube structure was not significantly affected by the immobilized Pt particles. Ti K-edge XANES spectra of TiO2 nanotube and Pt/TiO2-nanotube represent that most titanium are in a tetrahedral coordination with few retained in the octahedral structure.In the in-situ FT-IR experiments, an IR cell was evacuated to a pressure of 10-5 torr at room temperature as soon as the catalyst-pellet, Pt/TiO2 or Pt/TiO2-nanotube, was placed inside the cell.Then, 60 torr of hydrogen was introduced into the cell and subsequently the temperature was programmed to increase from room temperature to 300℃ at a constant heating rate of 5℃/min.For Pt/TiO2, an IR peak at 2083 em-1 started to appear at 200℃ with a maximum intensity at 250℃ and then decreasing as temperature increased. The 2083 em-1 IR peak corresponds to the linearly adsorption of CO on the well-dispersed Pt sites. Simultaneously, the IR bands of gaseous methane at 3016 em-1 started to appear at 225℃ and the peak intensity increased with temperature. The results reveal that Pt/TiO2 can adsorb gaseous CO2 and further catalyzes the reduction of CO2 by H2 through the intermediate CO, which further produces gaseous methane. While for the Pt/TiO2-nanotube catalyst, methane was produced at relatively low temperature, 100℃, and it catalyzed the direct conversion of CO2 to CH4. The absence of intermediate CO-adsorption signals durinng the temperature programmed process indicates that the prepared TiO2 nanotube-supported nanosize Pt possesses a potent capability for CO2 adsorption and highly catalytic activity in the hydrogenation of CO2, and was superior to the conventional Pt/TiO2 catalyst. The catalytic activity of Pt/TiO2-nanotube was indeed significantly enhanced by the high surface area of TiO2-nanotubes.Details will be discussed.     

炭黑负载Pt-Sn双金属催化剂对乙醇的电催化氧化性能

采用一步还原法(乙二醇为还原剂)与两步还原法(在聚乙烯吡咯烷酮PVP保护下,先用硼氢化钠还原制备Sn溶胶,沉积Pt后用乙二醇还原)制备了炭黑负载Pt-Sn双金属催化剂,利用循环伏安法和计时电流法考察了催化剂制备方法、Pt/Sn原子比、溶液p H值、PVP/Sn质量比、反应介质等对乙醇室温电催化氧化活性和稳定性的影响.以X光衍射、透射电镜及电化学活性面积测定对所得催化剂进行了表征.发现引入Sn明显提高了Pt催化剂对乙醇的电催化活性与稳定性,两步还原法得到的Pt3Sn/C催化剂具有更小的颗粒尺寸,更大的电化学活性面积及更高的乙醇氧化活性与稳定性.与酸性介质相比,该催化剂在碱性介质中的电化学活性更好.     

Effect of calcination temperature on the structure of a Pt/TiO2 (B) nanofiber and its photocatalytic activity in generating H2

Hydrogen trititanate (H 2Ti 3O 7) nanofibers were prepared by a hydrothermal method in 10 M NaOH at 403 K, followed by acidic rinsing and drying at 383 K. Calcining H 2Ti 3O 7 nanofibers at 573 K led to the formation of TiO 2 (B) nanofibers. Calcination at 673 K improved the crystallinity of the TiO 2 (B) nanofibers and did not cause any change in the morphology and dimensions of the nanofibers. TiO 2 (B) and H 2Ti 3O 7 nanofibers are 10-20 nm in diameter and several micrometers long, but FE-SEM reveals that several of these nanofibers tend to bind tightly to each other, forming a fiber bundle. Calcination at 773 K transformed TiO 2 (B) nanofibers into a TiO 2 (B)/anatase bicrystalline mixture with their fibrous morphology remaining intact. Upon increasing the calcination temperature to 873 K, most of the TiO 2 (B) nanofibers were converted into anatase nanofibers and small anatase particles with smoother surfaces. In the photocatalytic dehydrogenation of neat ethanol, 1% Pt/TiO 2 (B) nanofiber calcined at 673 K was the most active catalyst and generated about the same amount of H 2 as did 1% Pt/P-25. TPR indicated that the calcination of 1% Pt/TiO 2 (B) nanofiber at 573 K produced a poor Pt dispersion and poor activity. Calcination at a temperature higher than 773 K (in ambient air) resulted in an SMSI effect similar to that observed over TiO 2 in the reductive atmosphere. As suggested by XPS, such an SMSI effect decreased the surface concentration of Pt metal and created Pt (delta) sites, preventing Pt particles from functioning as a Schottky barrier and leading to a lower activity. Because of the synergetic effect between TiO 2 (B) and anatase phases, the bicrystalline mixture, produced by calcining at 773 K, was able to counter negative effects such as the reduction in surface area and the SMSI effect and maintained its photocatalytic activity.     

Photooxidation of a mustard gas simulant over TiO2-SiO2 mixed-oxide photocatalyst: site poisoning by oxidation products and reactivation

The photooxidation of 2-chloroethyl ethyl sulfide (2-CEES), a simulant for mustard gas, was studied using transmission IR spectroscopy on a mixed-oxide TiO2-SiO2 photocatalyst. Ultraviolet irradiation in the photon energy range from 2.1 to 5 eV was employed at a catalyst temperature of 200 K. Rapid photooxidation was observed by the loss of infrared intensity in the v(CHx) stretching region, and concomitant infrared features of adsorbed oxidation products were observed to develop. The oxidation products, captured on the photocatalyst at 200 K, were found to block 2-CEES readsorption. Upon heating the poisoned photocatalyst to about 300 K, infrared measurements indicate that the adsorbed CO2 oxidation product was desorbed. The capability for full readsorption of 2-CEES was achieved upon heating the poisoned photocatalyst to 397 K, and continued rapid photooxidation of the 2-CEES was then possible at about 1/3 the rate found for the fresh catalyst. Thus thermal treatment at 397 K of oxidation-product-poisoned TiO2-SiO2 material is able to partially restore the TiO2-SiO2 photooxidation activity.     

Visible light photocatalysis with platinized rutile TiO2 for aqueous organic oxidation

Platinized rutile TiO2 samples containing varying concentrations of Pt were synthesized using Kemira (KE, BET surface area 50 m2/g, from Finland), and Toto HT0270 (HT, BET surface area 2.9 m2/g, from Japan) as the starting materials by solution mixing followed by sintering the precursors. Photocatalytic activities were established for phenol oxidation under visible light (wavelength >400 nm). Our results show optimal performance for 8 wt % platinized KE (8 wt % Pt/KE) and (1/2) wt % platinized HT rutile samples. The specific roles of O2 and visible light were examined using the 8 wt % Pt/KE sample in either N2 gas ambient or no illumination. Separately, 8 wt % platinized SiO2 was tested to compare its performance with that of platinized rutile TiO2. Several other chemicals containing different functional groups (formic acid, salicylic acid, 4-chlorophenol, 2,4,6-trichlorophenol, diethyl phosphoramidate) were selected for photooxidation tests with (1/2) wt % platinized HT rutile. X-ray diffraction reveals Pt metal clusters segregating on the surface of rutile TiO2 particles with increasing Pt weight percent. The Pt cluster surface area broadly increases, while the effective optical band gap steadily decreases with platinization of the rutile samples. These results suggest that Pt clusters on the surface of rutile TiO2 particles serve to mediate electron transfer from rutile to O2, thus facilitating photooxidation of organic chemicals.     

Enhanced CO photocatalytic oxidation in the presence of humidity by tuning composition of Pd-Pt bimetallic nanoparticles supported on TiO2

Here we put forward for the first time that the negative effect of humidity on CO photooxidation at room temperature can be overcome by adjusting the composition of Pd-Pt bimetallic particles supported on TiO(2). Consequently, optimized Pd(x)Pt(1-x)/TiO(2) materials can be considered as common and efficient photocatalysts for simultaneous elimination of CO and VOCs in the presence of humidity, i.e. for real indoor air treatment.     

Formation mechanism of Pt particles by photoreduction of Pt ions in polymer solutions

The formation mechanisms of metal particles (platinum (Pt) particles) in an aqueous ethanol solution of poly(N-vinyl-2-pyrrolidone) (PVP) by the photoreduction method have been studied by transmission electron microscopy (TEM) and in situ and ex situ X-ray absorption fine structure (XAFS) analysis. The average diameter of the dilute and concentrated Pt particles in the PVP solution is estimated from TEM to be 2.0 and 2.5 nm, respectively. XAFS analysis was performed for the reduction process of Pt4+ ions to metallic Pt particles for the Pt L3 edge of the colloidal dispersions of the concentrated Pt solutions. The photoreduction process proceeds by the following steps: (1) reduction of PtCl6(2-) to PtCl4(2-), (2) dissociation of Cl from PtCl4(2-), followed by reduction of Pt2+ ionic species to Pt0, (3) formation of a Pt0-Pt0 bond and particle growth by the association of Pt0-Pt0. The reduction of PtCl4(2-) to Pt0 is a slower process, compared with the reduction of PtCl6(2-) to PtCl4(2-). There is a delay between the disappearance of PtCl4(2-) and the formation of Pt0-Pt0 clusters.     

氧化物担载铑原子簇催化剂的金属载体相互作用的考察——Ⅰ.Rh/V_2O_5和RH/TiO_2催化剂的金属载体强相互作用的比较

本文用XPS和XRD考察了由Rh_4(CO)_(12)出发制得的Rh/V_2O_5和Rh/TiO_2两种催化剂的金属载体强相互作用的差别。实验结果表明,1)高温H_2还原的Rh/TiO_2催化剂,经氧处理后即能恢复吸H_2能力。Rh/V_2O_5催化剂在较低温度(473K)H_2还原时Rh就进入SMSI状态,吸H_2能力被完全抑制,373K氧处理并不能使之恢复,吸H_2性质表现出不可逆性。2)与Rh/TiO_2催化剂的TiO_2相比,Rt/V_2O_5催化剂的V_2O_5更易还原,Rh对V_2O_5的还原有明显的促进作用。3)担载在TiO_2上的Rh比在V_2O_5上更易还原。4)还原后,催化剂表层的Rh/V、RH/Ti均有较大幅度的降低。用氧空位模型能较好地说明Rh/TiO_2催化剂的实验结果,而Rh/V_2O_5催化剂的实验结果适于用钒氧化物覆盖模型解释。     

Effects of reduction temperature and metal-support interactions on the catalytic activity of Pt/gamma-Al2O3 and Pt/TiO2 for the oxidation of CO in the presence and absence of H2

TiO2- and gamma-Al2O3-supported Pt catalysts were characterized by HRTEM, XPS, EXAFS, and in situ FTIR spectroscopy after activation at various conditions, and their catalytic properties were examined for the oxidation of CO in the absence and presence of H2 (PROX). When gamma-Al2O3 was used as the support, the catalytic, electronic, and structural properties of the Pt particles formed were not affected substantially by the pretreatment conditions. In contrast, the surface properties and catalytic activity of Pt/TiO2 were strongly influenced by the pretreatment conditions. In this case, an increase in the reduction temperature led to higher electron density on Pt, altering its chemisorptive properties, weakening the Pt-CO bonds, and increasing its activity for the oxidation of CO. The in situ FTIR data suggest that both the terminal and bridging CO species adsorbed on fully reduced Pt are active for this reaction. The high activity of Pt/TiO2 for the oxidation of CO can also be attributed to the ability of TiO2 to provide or stabilize highly reactive oxygen species at the metal-support interface. However, such species appear to be more reactive toward H2 than CO. Consequently, Pt/TiO2 shows substantially lower selectivities toward CO oxidation under PROX conditions than Pt/gamma-Al2O3.     

Pt/Ce0.75Zr0.25O2的催化性能及其氧移动性的 18O 同位素交换表征

 采用浸渍法制备了Pt/Ce0.75Zr0.25O2催化剂,考察了催化剂对乙醇及CO的氧化活性,并采用 18O 同位素交换、乙醇程序升温表面反应(C2H5OH-TPSR)、一氧化碳程序升温脱附(CO-TPD)和程序升温还原(H2-TPR)等技术对催化剂进行了表征. 结果表明, Pt/Ce0.75Zr0.25O2催化剂表现出较高的乙醇和CO氧化活性,其催化活性随着Pt负载量的增加而提高. 当Pt负载量为3%时,活性最高. 继续增加Pt负载量,催化剂活性下降. C2H5OH-TPSR和CO-TPD结果表明,催化剂对乙醇或CO的氧化活性与从催化剂表面脱附出来的CO2量有对应关系, CO2脱附量越大,催化剂活性越高. 18O 同位素交换结果表明,表面氧交换能力与其氧化活性有一定对应关系,催化剂的表面氧交换能力越高,氧化活性越高.     

Furfuraldehyde hydrogenation on titanium oxide-supported platinum nanoparticles studied by sum frequency generation vibrational spectroscopy: Acid-base catalysis explains the molecular origin of strong metal-support interactions

This work describes a molecular-level investigation of strong metal-support interactions (SMSI) in Pt/TiO(2) catalysts using sum frequency generation (SFG) vibrational spectroscopy. This is the first time that SFG has been used to probe the highly selective oxide-metal interface during catalytic reaction, and the results demonstrate that charge transfer from TiO(2) on a Pt/TiO(2) catalyst controls the product distribution of furfuraldehyde hydrogenation by an acid-base mechanism. Pt nanoparticles supported on TiO(2) and SiO(2) are used as catalysts for furfuraldehyde hydrogenation. As synthesized, the Pt nanoparticles are encapsulated in a layer of poly(vinylpyrrolidone) (PVP). The presence of PVP prevents interaction of the Pt nanoparticles with their support, so identical turnover rates and reaction selectivity is observed regardless of the supporting oxide. However, removal of the PVP with UV light results in a 50-fold enhancement in the formation of furfuryl alcohol by Pt supported on TiO(2), while no change is observed for the kinetics of Pt supported on SiO(2). SFG vibrational spectroscopy reveals that a furfuryl-oxy intermediate forms on TiO(2) as a result of a charge transfer interaction. This furfuryl-oxy intermediate is a highly active and selective precursor to furfuryl alcohol, and spectral analysis shows that the Pt/TiO(2) interface is required primarily for H spillover. Density functional calculations predict that O-vacancies on the TiO(2) surface activate the formation of the furfuryl-oxy intermediate via an electron transfer to furfuraldehyde, drawing a strong analogy between SMSI and acid-base catalysis.     

几种低碳醇在Pt／TiO2上的光催化产氢速率的研究

主要考察了无氧条件下低碳醇（甲、乙、丙醇）在Pt/TiO2表面光催化重整反应制氢。深入探讨了几种低碳醇与其放氢速率的构-效关系,提出了低碳醇在Pt/TiO2光催化剂表面吸附态的模型。     

微波辅助溶剂热法制备Pt/石墨烯-TiO2及其催化性能

质子交换膜燃料电池具有比能量高、结构简单、工作温度低、高效清洁和安静无摩擦等优点,是一种非常具有发展前景的电源.燃料电池借用电催化剂把燃料与氧化剂中的化学能转化为电能,通常采用碳粉负载的Pt催化剂.在燃料电池的工作环境下,碳粉载体容易腐蚀和团聚,降低了催化剂活性和稳定性,进而降低了燃料电池的使用寿命.因此,探索高稳定性的催化剂载体有利于提高催化剂的稳定性,促进燃料电池的实用化进程.为增强催化剂载体的抗腐蚀能力,一些金属氧化物如SnO2,WO3,CeO2和TiO2等被用作催化剂载体.其中,TiO2因具有稳定的化学性能以及与金属之间的"强相互作用"而备受研究者关注.但TiO2载体比表面积小和导电能力弱等缺点限制了它在燃料电池中的应用.石墨烯具有卓越的导电性和比表面积,却容易发生团聚.利用TiO2与碳材料间存在的协同作用,将TiO2与石墨烯复合来制备复合载体,能够增强TiO2的导电能力,抑制石墨烯的团聚,提高催化剂载体的化学稳定性和比表面积.本文采用微波辅助溶剂热法制备了石墨烯-TiO2复合载体和Pt/石墨烯-TiO2催化剂,研究了TiO2含量对催化剂活性和稳定性的影响.采用X射线衍射(XRD)、扫描电子显微镜(SEM)和透射电子显微镜(TEM)对制备的样品进行了微观结构和成分表征.结果表明,Pt/石墨烯-TiO2催化剂中TiO2为立方状纳米颗粒,粒径约为60 nm,均匀地分布在石墨烯上;Pt纳米粒子倾向于锚定在TiO2与石墨烯之间,而且分布均匀.采用线性伏安扫描(LSV)和循环伏安法(CV)测试了不同TiO2含量的Pt/石墨烯-TiO2催化剂的活性和稳定性.发现TiO2的加入确实能够提高催化剂的稳定性,随着TiO2含量的提高,催化剂稳定性增加.当TiO2含量为20%时,催化剂的起始电压与极限电流均与Pt/C催化剂接近.经过循环伏安扫描3000圈的快速老化测试后,Pt/石墨烯-TiO2催化剂起始电压的负移明显低于Pt/C催化剂,呈现了优良的稳定性和催化活性.     

Effects of calcium ions on solubility and aggregation behavior of an anionic sulfonate gemini surfactant in aqueous solutions

In this work, a ternary composite, Pt/TiO(2)/RGO (reduced graphite oxide), was prepared via immobilizing Pt particles onto the TiO(2)/RGO composite that was obtained via redox reaction of TiCl(3) and GO. The composite was characterized by different techniques including X-ray diffraction, transmission electron microscopy, and X-ray photoelectron spectroscopy. The TiO(2) particles with size less than 10 nm were uniformly distributed throughout the RGO, and almost each Pt particle with size around 3 nm adhered to TiO(2) particles, resulting in high dispersion of all Pt particles on the support. The Pt particles were in the electron-deficient state due to the strong interactions with the TiO(2) particles and the RGO support. The catalytic performance of the composite for nitrobenzene hydrogenation was investigated under solvent-free condition. It was indicated that the Pt/TiO(2)/RGO catalyst exhibited high activity with a turnover frequency (e.g., 59,000 h(-1)) as well as superior selectivity to aniline (e.g., >99%). Moreover, the catalyst can be reused for six times without any activity loss, which resulted from the stable structure of the catalyst.     

K改性的Pt/Al2O3催化剂上CO氧化反应：反应动力学和红外光谱研究

CO氧化不仅具有重要的实用价值,而且在基础研究中被用于考察反应机理及催化剂结构敏感性等一些重要问题,因此,该反应在催化领域中具有重要意义. Pt基催化剂被广泛应用于CO氧化反应.其催化活性取决于催化剂的制备方法.其中,碱金属如Na、K等助剂的添加可有效促进催化活性,红外光谱证据表明,其促进作用在于碱金属的添加可降低CO与表面Pt原子的相互作用.尽管如此,催化剂上反应动力学证据却十分缺乏.反应动力学的研究可以提供一些本证反应信息如反应基元步骤、反应速率表达式以及反应机理等.通过对比不同催化剂之间的反应动力学行为,可以进一步解释碱金属对催化剂结构以及反应行为的影响.因此在本工作中,我们制备了一系列以K为助剂的Pt/Al2O3催化剂,并进行了CO氧化的反应动力学研究,考察了助剂对CO反应级数和反应活化能的影响.结合原位红外光谱表征,进一步揭示了助剂在反应中的作用.通过对比不同Pt和K含量的催化剂上CO氧化反应活性,我们发现, K的添加能促进反应活性,且随着催化剂中K含量的增加,促进程度越明显.例如,0.42K-2Pt/Al2O3上T50温度比对应的2Pt/Al2O3降低了30oC.不同催化剂上CO氧化的反应动力学实验表明,反应速率随着CO的分压的增加而降低;但随着O2分压的增加而增大.幂函数反应速率表达式推导得到的反应级数发现,对于含K的催化剂其CO的反应级数(约为–0.2)明显比不含K的催化剂(约为–0.5)中高,说明K的添加减弱了CO与表面Pt原子之间的吸附能力.但对O2的反应级数影响较小.例如：在0.42K-2.0Pt/Al2O3上反应速率表达式为r =6.55′10–7pco–0.22po20.63;而在2.0Pt/Al2O3上为r =2.56′10–7pco–0.53po20.70.表观反应活化能的计算表明,含K的催化剂上表观反应活化能较低,进一步说明K的添加有利于反应进行.根据反应速率表达式,我们进行了基元步骤的推导,并计算了反应动力学参数.结果发现,与不含K的催化剂相比,含K的催化剂中本征反应速率常数明显增加,而CO吸附平衡常数降低了一半,表明K的存在使CO在Pt表面上的覆盖度降低.我们还通过原位红外光谱对比了催化剂上CO吸附行为的差异.数据表明,与不含K的催化剂相比, K的添加一方面降低了CO在催化剂表面的吸附量(峰面积变小);另一方面显著降低了CO在Pt表面上的脱附温度,说明两者之间的相互作用力减弱.综上所述,通过反应动力学和红外光谱实验,我们认为K助剂与表面Pt原子相互作用后生成了较为稳定的Pt–O–K物种.尽管该物种的具体结构目前还不明确,但我们的实验证据表明,该物种的存在可以有效减弱CO与表面Pt原子之间的相互作用,降低CO的表面覆盖度并有利于O2在Pt表面的竞争吸附,从而降低了表面吸附的CO与O2之间反应的能垒,促进了反应性能.     

Metal-support interaction and redox behavior of Pt(1 wt %)/Ce0.6Zr0.4O2

The catalyst Pt(1 wt %)/Ce(0.6)Zr(0.4)O(2) is studied by CO-temperature programmed reduction (CO-TPR), isothermal oxygen storage complete capacity (OSCC), X-ray absorption spectroscopy (XAS) at the Pt L(III) edge, and in situ X-ray diffraction (in situ XRD), with the aim of elucidating the role of supported metal in CO oxidation by ceria-based three-way catalysts (TWC). The redox behavior of Pt(1 wt %)/Ce(0.6)Zr(0.4)O(2) is compared to that of bare ceria-zirconia. OSCC of redox-aged Pt/ceria-zirconia is twice that of bare ceria-zirconia, and the maximum of CO consumption occurs at a temperature about 300 K lower than redox-aged ceria-zirconia. XAS analysis allows one to evidence the formation of a platinum-cerium alloy in redox-aged samples and the stability of the metal particles toward oxidation and sintering during high-temperature treatments. Under CO flux at 773 K, bare ceria-zirconia shows a continuous drift of diffraction peaks toward smaller Bragg angles, due to a progressive increase of Ce(III) content. Under the same treatment, the structural rearrangement of Pt-supported ceria-zirconia starts after an induction time and takes place with an abrupt change of the lattice constant. The experimental evidence points to the role of supported Pt in modifying the redox properties of ceria-zirconia with respect to the bare support. It is proposed that the much faster bulk reduction observed by in situ XRD for redox-aged Pt/ceria-zirconia can be attributed to an easier release of reacted CO(2), producing a more effective turnover of reactants at the catalyst surface.     

Surface properties of Ni-Pt/SiO2 catalysts for N2O decomposition and reduction by H2

The surface properties of bimetallic Ni-Pt/SiO2 catalysts with variable Ni/Ni + Pt atomic ratio (0.75, 0.50, and 0.25) were studied using N2O decomposition and N2O reduction by hydrogen reactions as probes. Catalysts were prepared by incipient wetness impregnation of the silica support with aqueous solutions of the metal precursors to a total metal loading of 2 wt %. For both model reactions, Pt/SiO2 catalyst was substantially more active than Ni/SiO2 catalyst. Mean particle size by TEM was about the same (in the range 6-8 nm) for all catalysts and truly bimetallic particles (more than 95%) were evidenced by EDS in the Ni-Pt/SiO2 catalysts. CO adsorption on the bimetallic catalysts showed differences in the linear CO absorption band as a function of the Ni/Pt atomic ratio. Bimetallic Ni-Pt/SiO2 catalysts showed, for the N2O decomposition, a catalytic behavior that points out an ensemble-size sensitive behavior for Ni-rich compositions. For the N2O + H2 reaction, the bimetallic catalysts were very active at low temperature. The following activity order at 300 K was observed: Ni75Pt25 > Ni25Pt75 approximately Ni50Pt50 > Pt. TOF values for these catalysts increased 2-5 times compared to the most active reference catalyst (Pt/SiO2). The enhancement of the activity in the Ni75Pt25 bimetallic catalysts is explained in terms of the presence of mixed Ni-Pt ensembles.     

Synthesis of conductive rutile-phased Nb0.06Ti0.94O2 and its supported Pt electrocatalysts (Pt/Nb0.06Ti0.94O2) for the oxygen reduction reaction

In this paper, Nb-doped TiO(2) with anatase and rutile phases was synthesized by the acid-catalyzed sol-gel method, and used as catalyst supports for the oxygen reduction reaction (ORR). X-ray diffraction (XRD), transmission electron microscopy (TEM), Energy dispersive X-ray spectroscopy (EDX), and Brunauer-Emmett-Teller (BET) were used to characterize the support materials in terms of material structures, morphology, composition, and surface area. XRD analysis showed that both the high concentration of hydrochloric acid present in the synthesis and the presence of Pt in the support could favor the formation of conductive rutile phased TiO(2), resulting in the improvement of electronic conduction of the Nb-doped TiO(2) support, which was confirmed by measured conductivities. For electrochemical characterization and ORR catalyst activity validation, Pt particles were deposited on the supports synthesized in this paper to form several catalysts, which were tested for electrochemical Pt surface area, ORR mass activity and specific activity. A monotonic increase in Pt ORR mass activity with increasing catalyst support's conductivity suggested that the support conductivity plays an important role in enhancing catalyst mass activity. The results showed that these non-carbon supported catalysts are promising as PEM fuel cell cathode catalysts.     

Three-dimensionally ordered macro-porous Pt/TiO2 catalyst used for water-gas shift reaction

Three-dimensionally ordered macro-porous (3DOM) Pt/TiO2 catalysts were prepared by template and impregna-tion methods, and the resultant samples were characterized by using TG-DTA, XRD, SEM, TEM, and TPR techniques. The catalytic performance for water-gas shift (WGS) reaction was tested, and the influences of some conditions, such as reduction temperature of catalysts, the amount of Pt loadings and space velocity on catalytic performance were investigated. It was shown that Pt particles were homogeneously dispersed on 3DOM TiO2. The reduction of TiO2 surface was important for the catalyticperformance. The activity test results showed that the 3DOM Pt/TiO2 catalysts exhibited very good catalytic performance for WGS reaction even at high space velocity, which was owing to the better mass transfer of 3DOM porous structure besides the high intrinsic activity of Pt/TiO2.     

Pt/C催化剂对乙醇电氧化的粒径效应

利用有机溶胶方法, 通过控制溶剂挥发温度制备了具有不同粒径大小的Pt/C催化剂. 制得的Pt/C催化剂中, Pt粒子具有非常优异的均一性和良好的分散度. 电化学研究表明, 对于乙醇的电催化氧化, Pt/C催化剂存在着明显的粒径效应. 当Pt粒子粒径为3.2 nm时, Pt/C催化剂对乙醇的电催化氧化的质量比活性最佳. X射线光电子能谱(XPS)的研究显示, Pt/C催化剂对乙醇氧化的粒径效应与其零价Pt含量以及Pt粒子的比表面积密切相关.