超微粒分子筛改性的玻璃毛细管柱的研制

以超微粒分子筛对毛细管内壁进行改性,成功地制备了不同极性的ＳＣＯＴ柱。实验结果表明,以超微粒分子筛改性的毛细管色谱柱具有预想的特性,并可得到准确的定量结果,因此成为应深入探讨的新柱型。     

超微粒分子筛多孔层毛细管气相色谱柱的初步研制

探讨了以超微粒分子筛成功地沉积于玻璃毛细管内壁制备出新型ＰＬＯＴ柱的方法。实验证明,这种ＰＬＯＴ柱具有快速、高效、稳定和选择分离等独到特性。     

超细微MEL结构铜硅分子筛的合成及理化性质

过渡金属杂原子分子筛的合成及其性质表征近年来引起了广泛关注[1～3].将铜离子嵌入分子筛、层柱状材料中作为活性中心,在汽车尾气处理[4]及有机物选择氧化反应[5]中呈现出良好的催化活性,其研究在理论和应用上均具有重要意义.超细微分子筛(粒径小于1×10-7m)具有比普通分子筛更高的比表面积和比活性,在不同领域有特殊的用途,其合成方法一直是分子筛研究工作者探索的热门课题.本文采用“络合物法”[6]首次合成了超细微纳米晶MEL结构铜硅分子筛,并通过XRD,TEM,XRF,FTIR,ESR,TG-DTA及NH3-TPD对其理化性质进行了研究.1　实验部分M…     

气相合成SnO2超微粒薄膜研究

用直流气体放电活化反应蒸发法在玻璃基片上沉积的SnO2超微粒薄膜,研究其过程中各工艺参数对薄膜结构的影响及作用机理.结果表明, SnO2超微粒薄膜粒径随氧分压增加而增大;蒸镀时间的延长有助于SnO2的生成,也使薄膜发生晶化;而增加放电电压,则薄膜出现外延单晶生长趋势.     

Fe2O3超微粒／硬脂酸得合LB膜的制备和表征研究

用超声分散的方法将Ｆｅ２Ｏ３超微粒分散于硬脂酯／正己烷／氯仿溶液中，用ＬＢ膜技术进行组装。结果表明：ＦｅＯ３超微粒能均匀地分散在有机溶剂中，并且能够被硬脂酸包裹；Ｆｅ２Ｏ３超微粒／硬酯酸单分子膜的成膜性能良好，Ｆｅ２Ｏ３超微粒／硬脂酸复合ＬＢ膜具有层状结构；在Ｆｅ２Ｏ３超微粒的晶格结构和硬脂酸单分子膜的晶格结构相匹配的情况下，Ｆｅ２Ｏ３超微粒能够被有序组装。     

硫化铅超微粒的制备及量子尺寸效应研究

通常表现明显能级量子化的超微粒结构被称作量子点,由于大而快的三阶非线性光学响应,这种材料很可能用于光计算机的开关、信号转换、信息存贮、运算等功能元件,实验表明,PbS超微粒表现出很强的三阶光学非线性响应。 我们用两种方法合成了3种PbS超微粒溶胶,测定了3种胶体粒子的粒度及紫外-可见     

苯乙烯—二乙烯基苯共聚超微球在溶液中的扩散行为

用光子相关光谱测定了苯乙烯-二乙烯基苯(St-DVB)共聚超微粒在良溶剂(甲苯)与θ溶剂(环己烷)中不同温度下的分子扩散系数,与流体力学方程结合给出了该微粒在无限稀时的等效流体力学半径。微粒分子扩散与温度的关系符合Arrhenius方程。不同温度的测试结果表明,St-DVB共聚超微粒的微交联网络结构使其分子形态不易改变。在θ溶剂中,T<θ时,微粒发生聚集,表现出大分子的协同扩散;T>θ时,在较高浓度,扩散系数偏离与浓度的线性关系。流体力学作用和热运动决定了微粒分子的扩散行为。     

硫化物半导体超微粒量子尺寸效应的光谱研究

用胶体化学方法在水溶液中制备了纳米硫尺寸硫化物半导体超微粒(CdS、ZnS、PbS、及Bi₂S₃),并用TEM测得超微粒颗粒尺寸小于10nm.本文详细研究了这些硫化物半导体超微粒的量子尺寸效应和光学性质以及制备过程中颗粒形成的化学环境与条件参数的影响。可以观察到它们收光谱及喇曼光谱(CdS)的明显变化。采用合适的表面修饰剂和稳定剂、将溶液的pH控制在适当的范围以及金属离子的过量等,都可使超微粒的吸收光谱明显蓝移并出现结构峰。对于CdS超微粒,其特征共振喇曼峰逐渐减弱直至最后消失。这些都表明了硫化物半导体超微粒尺寸逐渐减小而呈现出明显的量子尺寸效应。     

Fe_2O_3超微粒/硬脂酸复合LB膜的制备和表征研究

用超声分散的方法将Ｆｅ２Ｏ３超微粒分散于硬脂酸／正己烷／氯仿溶液中，用ＬＢ膜技术进行组装。结果表明：Ｆｅ２Ｏ３超微粒能均匀地分散在有机溶剂中，并且能够被硬脂酸包裹；Ｆｅ２Ｏ３超微粒／硬酯酸单分子膜的成膜性能良好，Ｆｅ２Ｏ３超微粒／硬脂酸复合ＬＢ膜具有层状结构；在Ｆｅ２Ｏ３超微粒的晶格结构和硬脂酸单分子膜的晶格结构相匹配的情况下，Ｆｅ２Ｏ３超微粒能够被有序组装。     

不同化学微环境PbS超微粒的制备与光谱研究

合成了一系列表面化学环境不同的PbS超微粒溶胶,用紫外-可见吸收光谱及荧光光谱对其光学性质进行了研究.实验发现,在室温下可观察到有明显的量子尺寸效应,吸收谱、发射谱及激发谱有分立峰结构;表面化学环境对超微粒的光学性质影响很大,表面包覆AOT的PbS超徽粒在1.1 μm处有宽的红外发光带,而包覆DBS时则观察不到红外发光.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.