La0.67Sr0.33Mn1-yFeyO3(y=0, 0.01, 0.02, 0.03)磁谱特性分析

采用固相反应法制备了La0．67Sr0．33Mn1-yFeyO3（y=0,0．01,0．02,0．03）氧化物多晶样品,XRD测试表明形成了钙钛矿单相结构,铁掺人后材料的晶体结构没有明显变化。SEM测试表明样品晶粒大小为1～3μm,随着铁含量增加饱和磁化强度下降。样品室温磁导率（10kHz～1．8GHz）测试表明,复磁导率频谱曲线是典型的弛豫型谱线,且随铁离子含量增加其起始磁导率下降。同时通过最小二乘曲线拟合的方法分析了频谱曲线,分别给出了畴壁位移和磁畴转动对磁导率的贡献,结果表明,y=0,0．01的样品畴壁位移对磁导率的贡献大于畴转对磁导率的贡献,y=0．02,0．03的样品,畴转对磁导率的贡献大于畴壁位移的贡献。     

Zn—Co替代Y-型铁氧体的柠檬酸盐溶液-凝胶合成及微波性能研究

采用柠檬酸盐溶胶一凝胶工艺合成了Ba2ZnxCO2-xFe12O22(x=0.O，0.4，0．8，1．2，1．6，2.0)o型铁氧体材料。研究了100MHz-6GHz频率范围内，合成铁氧体的复介电常数、复磁导率与测试频率、铁氧体组成和热处理温度之间的关系。所有合成的Ba2ZnxCo2-xFel2O22铁氧体，其磁导率虚部与频率关系图上都存在一个由自然共振引起的共振峰，该共振峰所对应频率与铁氧体中锌离子含量和热处理温度密切相关。Co2-Y型铁氧体的计算共振频率值与实验值基本相符。其电磁波吸收率随测试频率和样品厚度的增加而增加。     

2.45GHz下常用有机试剂复介电常数的测量与研究

1986年加拿大的R．Gedye和R．J．Giguere等发现了微波可以显著加快有机合成，他们发现用微波辐射可使反应速率和产率有不同程度的提高。由于微波作用机理的特殊性，微波化学对很多化学领域带来了冲击。但是，微波与化学反应体系之间相互作用的一些重大问题还未得到解决，如微波加热过程中化学反应系统的非线性反射、非均匀加热等。解决这类问题，首先必须了解化学反应过程中混合物的电学性质与磁学性质，而物质的宏观电学和磁学性质都用其介电常数和磁导率来描述。对于大部分是非磁性材料的有机试剂，微波与反应体系相互作用的特性集中体现在体系的等效复介电常数上。了解各种常用试剂的复介电常数，可以进一步了解各种化学试剂对微波的吸收和反射的情况。而很多试剂的复介电常数无法从现有文献中得到。本文利用谐振腔微扰法测定了在2．45GHz室温下各类常用有机试剂的复介电常数，结果显示：醇类试剂复介电常数实部与虚部都较大；酮类试剂复介电常数实部相对较大，而虚部较小；酸类试剂复介电常数实部和虚部都较小；烷烃和苯类试剂实部，虚部更小。同时，随着碳链增加，所有试剂的复介电常数的实部与虚部均有下降趋势。这些测试和分析结果将为微波辅助有机合成提供了有益参考。     

La0．8Sr0．2Mn1-xCoxO3（x=0，0．3，0．5，1）的磁性转变

采用柠檬酸络合法制备B位掺杂的纳米钙钛矿复合氧化物La0．8Sr0．2Mn1-xCoxO3（x=0，0．3，0．5，1．0）。应用X射线衍射法（XRD）进行结构的测定与分析，并结合扫描电镜（SEM）和热磁曲线（M-T曲线）的实验结果，研究这4种样品的结构和磁性之间的关系。X射线衍射实验分析表明4个样品均属六方晶系，M-T曲线得出的1／χ-T曲线表明：La0．8Sr0．2MnO3是铁磁性，La0.8Sr0．2Mn0．7Co0．3O3和La0．8Sr0．2Mn0.5Co0．5O3是亚铁磁性，而La0．8Sr0．2CoO3是反铁磁性的。利用电镜观察到前3种样品均为颗粒状，颗粒之间首尾相接形成链状结构，并进一步由链状结构支起一个个的空间网状结构，最后一种样品为较为分散的颗粒。     

La0.6Sr0.4Co1-yFeyO3(y=0.2,0.8)复合氧化物混合导电性能研究

采用甘氨酸-硝酸盐（GNP）法制备了La0．6Sr0．4Co1-yFeyO3（y=0．2，0．8）g合氧化物，研究了材料的结构、电子-离子混合导电性能及其相关性。结果表明，La0.6Sr0.4Co1-yFeyO3（y=0．2，0．8）合成粉料的颗粒细小均匀（～100nm），陶瓷形成菱形六面体钙钛矿结构。与La0．6Sr0．4Co0．2Fe0．8O3（y=0．8）陶瓷相比，La0.6Sr0.4Co0．8Fe0．2O3（y=0．2）陶瓷的晶粒尺寸大、致密度较高。在La0.6Sr0.4Co0．8Fe0．2O3（y=0．2）陶瓷中观察到Co^3＋离子歧化对电子导电性能的影响。与La0.6Sr0.4Co0.2Fe0.8O3（y=0．8）陶瓷相比，La0.6Sr0.4Co0.8Fe0．2O3（y=0．2）陶瓷具有更优异的电子-离子混合导电性能，材料在混合导电性能上的差异与其电子结构和显微结构紧密相关。     

钙钛矿型(La_(0.8)M_(0.2))MnO_3和(La_(0.8)Sr_(0.2))(Mn_(1-x)Fe_x)O_3的XRD和IR光谱的研究

合成了（La0.8M0.2）MnO3（M=Ca2+，Sr2+，Ba2+）和（La0.8Sr0.2）（Mn1-xFex）O3（x=0．1、0．2、0．3、0．4、0．5）两类氧化物，经XRD确认为钙铁矿型氧化物，应用FT－IR对其进行研究，对主要的红外特征振动υ（Mn-O）和δ（O-Mn-O）进行分析表征。这类化合物的υ（Mn-O）和δ（O-Mn-O）的FT－IR特征吸收峰十分相似，但在～608cm－1处出现较大差别，以Sr2+、Ca2+和Ba2+部分A位取代La3+的钙铁矿型氧化物和B位Fe取代Mn时，由于离子的溶解能不同，对晶格的有序排列的影响程度不一，导致了Mn－O键的键力场不同，引起了吸收峰向低波数移动。这种结构上的差异，导致对汽车尾气中的有害成份碳氢化合物（HC）和一氧化碳（CO）的催化氧化能力降低。借此可以用于研究结构与催化性能的关系。     

高效液相色谱-蒸发光散射检测器测定食品中胆固醇含量

建立了可满足各类食品（包括动物性食品、动植物混合食品）中胆固醇的HPLC—ELSD快速测定方法。样品经50％（w）KQH直接皂化和石油醚萃取后进行色谱分析。色i普柱为ODS柱,流动相为乙醇和乙脯,通过优化梯度洗脱条件,在20min内实现了胆固醇与干扰物质（如植物甾醇）的有效分离,分离度月大于1．5。胆固醇色谱峰面积的自然对数与浓度的自然对数呈良好的线性关系（r〉0．9996）,检出限（LOD）为0.20μg（S／N=3）,定量下限（LOQ）为0．56μg（S／N=10）,回收率为93％-96％（n=6）,重复性RSD〈3．0％（n=6）。     

聚碳硅烷热解SiC陶瓷结构与微波吸收性能

以聚碳硅烷(PCS)为原料,通过800-1200℃热解制备了PCS-SiC陶瓷,采用SEM、XRD与拉曼光谱对样品形貌、晶相及自由碳结构进行了表征。测量了样品直流电导率,并用矩形波导法测试了试样在8.2-12.4 GHz(X波段)频率范围的复介电常数,根据传输线理论计算出不同厚度材料的反射损耗。结果表明,随着热解温度的升高,样品电导率升高,同时复介电常数实部与虚部增加,吸波性能得到改善。PCS-SiC陶瓷中自由碳石墨化是引起极化能力及电导损耗提高的原因。     

LSMO/SiO2复合材料变温微波吸收特性研究

通过固相反应法制备了LSMO/SiO2复合材料, 测试了LSMO材料500 MHz～18 GHz介电特性和LSMO/SiO2复合材料样品不同温度下X波段介电常数和微波吸收特性. 测试结果表明, 在12 GHz附近复合材料样品有明显的介电损耗特征峰, 随着温度的升高材料的介电常数虚部明显升高, tgδ变大;吸收特性测试表明, 随着温度升高, 吸收峰升高, 吸收峰略微往低频移动.     

铝-铬天菁S-CTMAB分光光度法测定四氯化钛中的微量铝

在pH5．0～6．5的溶液中，铝离子（Al^3＋）与铬天菁S、CTMAB生成蓝色三元络合物，最大吸收波长为610nm。铝含量在2～10μg/（50mL）与吸光度呈良好的线性关系，摩尔吸光系数ε=9×10^6L／（moL·cm）。样品进行测定结果的相对标准偏差为0．82％～1．24％（n=5），加标回收率为97．5％-100．8％。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.