Al2O3绝缘层的AlGaN/GaN MOSHEMT器件研究

在研制AlGaN/GaN HEMT器件的基础上,采用ALD法制备了Al₂O₃ AlGaN/GaN MOSHEMT器件.通过X射线光电子能谱测试表明在AlGaN/GaN异质结材料上成功淀积了Al₂O₃薄膜.根据对HEMT和MOSHEMT器件肖特基电容、器件输出以及转移特性的测试进行分析发现：所制备的Al₂O₃薄膜与AlGaN外延层间界面态密度较小,因而MOSHEMT器件呈现出较 关键词： 2O₃')" href="#">Al₂O₃ ALD GaN MOSHEMT     

Significant performance enhancement in AlGaN/GaN high electron mobility transistor by high-κ organic dielectric

The electrical properties of AlGaN/GaN high electron mobility transistor (HEMT) with and without high-κ organic dielectrics are investigated. The maximum drain current I_{D max} and the maximum transconductance g_{m max} of the organic dielectric/AlGaN/GaN structure can be enhanced by 74.5%, and 73.7% compared with those of the bare AlGaN/GaN HEMT, respectively. Both the threshold voltage V_T and g_{m max} of the dielectric/AlGaN/GaN HEMT are strongly dielectric-constant-dependent. Our results suggest that it is promising to significantly improve the performance of the AlGaN/GaN HEMT by introducing the high-κ organic dielectric.     

An AlGaN/GaN HEMT with reduced surface electric field and improved breakdown voltage

A reduced surface electric field in AlGaN/GaN high electron mobility transistor (HEMT) is investigated by employing a localized Mg-doped layer under the two-dimensional electron gas (2-DEG) channel as an electric field shaping layer. The electric field strength around the gate edge is effectively relieved and the surface electric field is distributed evenly as compared with those of HEMTs with conventional source-connected field plate and double field plate structures with the same device physical dimensions. Compared with the HEMTs with conventional source-connected field plate and double field plate, the HEMT with Mg-doped layer also shows that the breakdown location shifts from the surface of the gate edge to the bulk Mg-doped layer edge. By optimizing both the length of Mg-doped layer, L_m, and the doping concentration, a 5.5 times and 3 times the reduction in the peak electric field near the drain side gate edge is observed as compared with those of the HEMTs with source-connected field plate structure and double field plate structure, respectively. In a device with V_GS=-5 V, L_m=1.5 μm, a peak Mg doping concentration of 8× 10¹⁷ cm^-3 and a drift region length of 10 μm, the breakdown voltage is observed to increase from 560 V in a conventional device without field plate structure to over 900 V without any area overhead penalty.     

An AlGaN/GaN HEMT with enhanced breakdown and near-zero breakdown voltage temperature coefficient

An AlGaN/GaN high-electron mobility transistor (HEMT) with a novel source-connected air-bridge field plate (AFP) is experimentally verified. The device features a metal field plate that jumps from the source over the gate region and lands between the gate and drain. When compared to a similar size HEMT device with conventional field plate (CFP) structure, the AFP not only minimizes the parasitic gate to source capacitance, but also exhibits higher OFF-state breakdown voltage and one order of magnitude lower drain leakage current. In a device with a gate to drain distance of 6 μm and a gate length of 0.8 μm, three times higher forward blocking voltage of 375 V was obtained at V_GS=-5 V. In contrast, a similar sized HEMT with CFP can only achieve a breakdown voltage no higher than 125 V using this process, regardless of device dimensions. Moreover, a temperature coefficient of 0 V/K for the breakdown voltage is observed. However, devices without field plate (no FP) and with optimized conventional field plate (CFP) exhibit breakdown voltage temperature coefficients of -0.113 V/K and -0.065 V/K, respectively.     

An improved EEHEMT model for kink effect on AlGaN/GaN HEMT

In this paper, a new current expression based on both the direct currect(DC) characteristics of the AlGaN/GaN high election mobility transistor(HEMT) and the hyperbolic tangent function tanh is proposed, by which we can describe the kink effect of the AlGaN/GaN HEMT well. Then, an improved EEHEMT model including the proposed current expression is presented. The simulated and measured results of I–V, S-parameter, and radio frequency(RF) large-signal characteristics are compared for a self-developed on-wafer AlGaN/GaN HEMT with ten gate fingers each being 0.4-μm long and 125-μm wide(Such an AlGaN/GaN HEMT is denoted as AlGaN/GaN HEMT(10 × 125 μm)). The improved large signal model simulates the I–V characteristic much more accurately than the original one, and its transconductance and RF characteristics are also in excellent agreement with the measured data.     

Sodium beta-alumina thin films as gate dielectrics for A1GaN/GaN metal-insulator-semiconductor high-electron-mobility transistors

<正>Sodium beta-alumina（SBA） is deposited on AlGaN/GaN by using a co-deposition process with sodium and Al₂O₃ as the precursors.The X-ray diffraction（XRD） spectrum reveals that the deposited thin film is amorphous.The binding energy and composition of the deposited thin film,obtained from the X-ray photoelectron spectroscopy（XPS） measurement,are consistent with those of SBA.The dielectric constant of the SBA thin film is about 50.Each of the capacitance-voltage characteristics obtained at five different frequencies shows a high-quality interface between SBA and AlGaN.The interface trap density of metal-insulator-semiconductor high-electron-mobility transistor（MISHEMT） is measured to be（3.5～9.5）×10¹⁰ cm^-2·eV^-1 by the conductance method.The fixed charge density of SBA dielectric is on the order of 2.7×10¹² cm^-2.Compared with the AlGaN/GaN metal-semiconductor heterostructure high-electronmobility transistor（MESHEMT）,the AlGaN/GaN MISHEMT usually has a threshold voltage that shifts negatively. However,the threshold voltage of the AlGaN/GaN MISHEMT using SBA as the gate dielectric shifts positively from—5.5 V to—3.5 V.From XPS results,the surface valence-band maximum（VBM-E_F） of AlGaN is found to decrease from 2.56 eV to 2.25 eV after the SBA thin film deposition.The possible reasons why the threshold voltage of AlGaN/GaN MISHEMT with the SBA gate dielectric shifts positively are the influence of SBA on surface valence-band maximum （VBM-E_F）,the reduction of interface traps and the effects of sodium ions,and/or the fixed charges in SBA on the two-dimensional electron gas（2DEG）.     

Ni/Au Schottky gate oxidation and BCB passivation for high-breakdown-voltage AlGaN/GaN HEMT

A new AlGaN/GaN high electron mobility transistor (HEMT) employing Ni/Au Schottky gate oxidation and benzocyclobutene (BCB) passivation is fabricated in order to increase a breakdown voltage and forward drain current. The Ni/Au Schottky gate metal with a thickness of 50/300 nm is oxidized under oxygen ambient at 500 C and the highly resistive NiO is formed at the gate edge. The leakage current of AlGaN/GaN HEMTs is decreased from 4.94 μA to 3.34 nA due to the formation of NiO. The BCB, which has a low dielectric constant, successfully passivates AlGaN/GaN HEMTs by suppressing electron injection into surface states. The BCB passivation layer has a low capacitance, so BCB passivation increases the switching speed of AlGaN/GaN HEMTs compared with silicon nitride passivation, which has a high dielectric constant. The forward drain current of a BCB-passivated device is 199 mA /mm, while that of an unpassivated device is 172 mA /mm due to the increase in two-dimensional electron gas (2DEG) charge.     

AlGaN/GaN HEMTs grown on silicon (001) substrates by molecular beam epitaxy

We report the realization of an AlGaN/GaN HEMT on silicon (001) substrate with noticeably better transport and electrical characteristics than previously reported. The heterostructure has been grown by molecular beam epitaxy. The 2D electron gas formed at the AlGaN/GaN interface exhibits a sheet carrier density of 8×10¹² cm⁻² and a Hall mobility of 1800 cm²/V s at room temperature. High electron mobility transistors with a gate length of 4 μm have been processed and DC characteristics have been achieved. A maximum drain current of more than 500 mA/mm and a transconductance g_m of 120 mS/mm have been obtained. These results are promising and open the way for making efficient AlGaN/GaN HEMT devices on Si(001).     

InGaAs/InP heterojunction-channel tunneling field-effect transistor for ultra-low operating and standby power application below supply voltage of 0.5 V

An In_0.53Ga_0.47As/InP heterojunction-channel tunneling field-effect transistor (TFET) with enhanced subthreshold swing (S) and on/off current ratio (I_on/I_off) is studied. The proposed TFET achieves remarkable characteristics including S of 16.5 mV/dec, on-state current (I_on) of 421 μA/μm, I_on/I_off of 1.2 × 10¹² by design optimization in doping type of In_0.53Ga_0.47As channel at low gate (V_GS) and drain voltages (V_DS) of 0.5 V. Comparable performances are maintained at V_DS below 0.5 V. Moreover, an extremely fast switching below 100 fs is accomplished by the device. It is confirmed that the proposed TFET has strong potentials for the ultra-low operating power and high-speed electron device.     

Structural characterization of Mg substituted on A/B sites in $$\hbox {NiFe}_2\hbox {O}_4$$ nanoparticles using autocombustion method

A compact quantitative model based on oxide semiconductor interface density of states (DOS) is proposed for Al_0.25Ga_0.75N/GaN metal oxide semiconductor high electron mobility transistor (MOSHEMT). Mathematical expressions for surface potential, sheet charge concentration, gate capacitance and threshold voltage have been derived. The gate capacitance behaviour is studied in terms of capacitance–voltage (CV) characteristics. Similarly, the predicted threshold voltage (V _T) is analysed by varying barrier thickness and oxide thickness. The positive V _T obtained for a very thin 3 nm AlGaN barrier layer enables the enhancement mode operation of the MOSHEMT. These devices, along with depletion mode devices, are basic constituents of cascode configuration in power electronic circuits. The expressions developed are used in conventional long-channel HEMT drain current equation and evaluated to obtain different DC characteristics. The obtained results are compared with experimental data taken from literature which show good agreement and hence endorse the proposed model.     

High-quality two-dimensional electron gas at large scale GaN/AlGaN wafer interface prepared by mass production MOCVD systems

Basic electronic properties of two-dimensional electron gas (2DEG) formed at GaN/AlGaN hetero-interface in large-scale (100 mm) wafer made by metal organic chemical vapour deposition (MOCVD) have been reported and discussed. From conventional Hall measurements, highest electron mobility was found to be μ_e∼1680 and 9000 cm²/V s at room temperature and at ∼5 K, respectively, for sheet electron density of n_s∼8×10¹² cm⁻². In magneto-resistance (MR) measurements carried out at 1.5 K in Hall bar sample defined by photolithography and ion implantation, very clear Schubnikov de-Haas oscillations and integer quantum Hall effect were observed in diagonal (R_xx) and off-diagonal (R_xy) resistances, respectively. In addition, a good insulating nature of GaN layer is confirmed by capacitance-voltage (C-V) measurement. These results suggest the high-qualitiness of our 100 mm GaN/AlGaN high electron mobility transistor (HEMT) wafers comparable to those so far reported.     

Influence of AlN interfacial layer on electrical properties of high-Al-content Al0.45Ga0.55N/GaN HEMT structure

Unintentionally doped high-Al-content Al_0.45Ga_0.55N/GaN high electron mobility transistor (HEMT) structures with and without AlN interfacial layer were grown by metal-organic chemical vapor deposition (MOCVD) on two-inch sapphire substrates. The effects of AlN interfacial layer on the electrical properties were investigated. At 300 K, high two-dimensional electron gas (2DEG) density of 1.66 × 10¹³ cm⁻² and high electron mobility of 1346 cm² V⁻¹ s⁻¹ were obtained for the high Al content HEMT structure with a 1 nm AlN interfacial layer, consistent with the low average sheet resistance of 287 Ω/sq. The comparison of HEMT wafers with and without AlN interfacial layer shows that high Al content AlGaN/AlN/GaN heterostructures are potential in improving the electrical properties of HEMT structures and the device performances.     

High vertical breakdown strength in with low specific on‐resistance AlGaN/AlN/GaN HEMTs on silicon

Off‐state and vertical breakdown characteristics of AlGaN/AlN/GaN high‐electron‐mobility transistors (HEMTs) on high‐resistivity (HR)‐Si substrate were investigated and analysed. Three‐terminal off‐state breakdown (BV_gd) was measured as a function of gate–drain spacing (L_gd). The saturation of BV_gd with L_gd is because of increased gate leakage current. HEMTs with L_gd = 6 µm exhibited a specific on‐resistance R_DS[ON] of 0.45 mΩ cm². The figure of merit (FOM = BV_gd²/R_DS[ON]) is as high as 2.0 × 10⁸ V² Ω^–1 cm^–2, the highest among the reported values for GaN HEMTs on Si substrate. A vertical breakdown of ～1000 V was observed on 1.2 µm thick buffer GaN/AlN grown on Si substrate. The occurrence of high breakdown voltage is due to the high quality of GaN/AlN buffer layers on Si substrate with reduced threading dislocations which has been confirmed by transmission electron microscopy (TEM). This indicates that the AlGaN/AlN/GaN HEMT with 1.2 µm thick GaN/AlN buffer on Si substrate is promising candidate for high‐power and high‐speed switching device applications. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

AlGaN/GaN MIS-HEMT using NbAlO dielectric layer grown by atomic layer deposition

We present an AlGaN/GaN metal-insulator-semiconductor high electron mobility transistor (MIS-HEMT) with an NbAlO high-k dielectric deposited by atomic layer deposition (ALD).Surface morphology of samples are observed by atomic force microscopy (AFM),indicating that the ALD NbAlO has an excellent-property surface.Moreover,the sharp transition from depletion to accumulation in capacitance-voltage (C-V)curse of MIS-HEMT demonstrates the high quality bulk and interface properties of NbAlO on AlGaN.The fabricated MIS-HEMT with a gate length of 0.5 μm exhibits a maximum drain current of 960 mA/mm,and the reverse gate leakage current is almost 3 orders of magnitude lower than that of reference HEMT.Based on the improved direct-current operation,the NbAlO can be considered to be a potential gate oxide comparable to other dielectric insulators.     

Investigating gate metal induced reduction of surface donor density in GaN/AlGaN/GaN heterostructure by electroreflectance spectroscopy

The internal field of GaN/AlGaN/GaN heterostructure on Si-substrate was investigated by varying the thickness of an undoped-GaN capping layer using electroreflectance spectroscopy. The four samples investigated are AlGaN/GaN heterostructure without a GaN cap layer (reference sample) and three other samples with GaN/AlGaN/GaN heterostructures in which the different thickness of GaN cap layer (2.7 nm, 7.5 nm, and 12.4 nm) has been considered. The sheet carrier density (n_s) of a two-dimensional electron gas has decreased significantly from 4.66 × 10¹² cm⁻² to 2.15 × 10¹² cm⁻² upon deposition of a GaN capping layer (12.4 nm) over the reference structure. Through the analysis of internal fields in each GaN capping and AlGaN barrier layers, it has been concluded that the undiminished surface donor states (n_s) of a reference structure and the reduced n_s caused by the Au gate metal are approximately 5.66 × 10¹² cm⁻² and 1.08 × 10¹² cm⁻², respectively.     

AlGaN/GaN肖特基结参数分析与电流运输机理研究

通过对AlGaN/GaN HEMT器件肖特基栅电流输运机理的研究,在变温下采用I-V法对AlGaN/GaN上的Ni/Au肖特基势垒高度和理想因子进行了计算. 通过对不同电流机理的分立研究,得到了更为准确的势垒高度值_b. 通过分析温度在300—550K之间肖特基反向泄漏电流的特性,得出结论：AlGaN材料的表面漏电不是HEMT器件反向泄漏电流的主要来源. 关键词： AlGaN/GaN异质结 肖特基结 理想因子     

具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管

介绍了一种具有高阈值电压和大栅压摆幅的常关型槽栅AlGaN/GaN金属氧化物半导体高电子迁移率晶体管。采用原子层淀积(ALD)方法实现Al₂O₃栅介质的沉积。槽栅常关型AlGaN/GaN MOS-HEMT的栅长(L_g)为2 μm,栅宽(W_g)为0.9 mm(0.45 mm×2),栅极和源极(L_gs)之间的距离为5 μm,栅极和漏极(L_gd)之间的距离为10 μm。在栅压为－20 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电仅为0.65 nA。在栅压为+12 V时,槽栅常关型AlGaN/GaN MOS-HEMT的栅漏电为225 nA。器件的栅压摆幅为－20~+12 V。在栅压V_gs=+10 V时,槽栅常关型AlGaN/GaN MOS-HEMT电流和饱和电流密度分别达到了98 mA和108 mA/mm (W_g=0.9 mm), 特征导通电阻为4 mΩ·cm²。槽栅常关型AlGaN/GaN MOS-HEMT的阈值电压为+4.6 V,开启与关断电流比达到了5×10⁸。当V_ds=7 V时,器件的峰值跨导为42 mS/mm (W_g=0.9 mm,V_gs=+10 V)。在V_gs=0 V时,栅漏间距为10 μm的槽栅常关型AlGaN/GaN MOS-HEMT的关断击穿电压为450 V,关断泄露电流为0.025 mA/mm。     

Degradation and recovery properties of AlGaN/GaN high-electron mobility transistors under direct current reverse step voltage stress

Direct current (DC) reverse step voltage stress is applied on the gate of AlGaN/GaN high-electron mobility transistor (HEMT). Experiments show that parameters degenerate under stress. Large-signal parasitic source/drain resistance (R_S/R_D) and gate-source forward I-V characteristics are recoverable after breakdown of the device under test (DUT). Electrons trapped by both the AlGaN barrier trap and the surface state under stress lead to this phenomenon, and surface state recovery is the major reason for the recovery of device parameters.     

Channel temperature determination of multifinger AlGaN/GaN high electron mobility transistor using micro-Raman technique

Self-heating in multifinger AlGaN/GaN high electron mobility transistor (HEMT) is investigated by micro-Raman spectroscopy. The device temperature is probed on the die as a function of applied bias. The operating temperature of AlGaN/GaN HEMT is estimated from the calibration curve of passively heated AlGaN/GaN structure. A linear increase of junction temperature is observed when direct current dissipated power is increased. When the power dissipation is 12.75 W at a drain voltage of 15 V, a peak temperature of 69.1 ℃ is observed at the gate edge on the drain side of the central finger. The position of the highest temperature corresponds to the high-field region at the gate edge.     

AlGaN/GaN高电子迁移率晶体管中kink效应的半经验模型

初步分析了AlGaN/GaN 器件上的kink效应. 在直流模型的基础上, 建立了AlGaN/GaN 高电子迁移率晶体管中kink效应的半经验模型, 并加入了kink效应发生的漏源偏压与栅源偏压的关系. 该模型得出较为准确的模拟结果, 可用来判断kink效应的发生和电流的变化量. 最后, 我们采用模型仿真结合实验分析的方法, 对kink效应进行了一定的物理研究, 结果表明碰撞电离对kink效应的发生有一定的促进作用.