微波辐射高效共价固定青霉素酰化酶

为提高青霉素酰化酶的共价固定化效率, 在微波辐射条件下将酶蛋白共价固定于介孔泡沫硅(MCFs)的孔道中. 通过正硅酸四乙酯水解缩合制备介孔泡沫硅, 再于微波辅助下将青霉素酰化酶共价固定在其孔道中. 以固定化酶相对活力和活力回收为指标, 考察了加酶量、固定化温度、微波辐射时间等条件对酶固定化效率的影响. 实验结果表明: 当加酶量为60 mg/g, 固定化温度为20 ℃, 微波辐射140 s, 固定化酶相对活力达到178.1%, 表观活力为1191.3 U/g(以湿重计). 与常规方法相比, 微波辅助固定化酶时, 固定化酶相对活力提高34.5%, 固定化时间亦大幅缩短至数分钟, 这为青霉素酰化酶的高效共价固定化提供了一条新的途径.     

多功能淀粉酶固定化中的底物保护效应

以壳聚糖为载体,通过正交实验确定了用壳聚糖凝胶微球固定多功能淀粉酶OPMA-N的最适条件:以20 mg/m L戊二醛交联,在25℃及p H=6.5条件下固定1.5 h,但需在引入底物淀粉介导的保护效应后,才能获得良好稳定性的固定化OPMA-N(IOPMA-N),显示了底物保护效应在催化部位占分子中较大区域的酶(如OPMA-N)固定化过程中的重要性.对比分析游离酶与固定化酶的性质与功能发现,在50℃及p H=6.0~7.0条件下,IOPMA-N的表观比活力比游离酶OPMA-N提高3倍以上,催化效率(kcat/Km)提高4倍以上,对弱酸性至中性及常温(30~50℃)环境的耐受性明显高于OPMA-N,并具有良好的操作稳定性和储存稳定性,重复使用15次后,酶活力仍然能够保持75%,在4℃下储存半衰期达31 d,而OPMA-N在4℃下储存5 d后活力基本丧失.催化产物的对比分析结果表明,OPMA-N固定化后,水解活性明显提高,但同时转苷活性有所下降,这与已报道的OPMA-N分子中2种催化活力存在平衡机制的结论一致,同时也表明在OPMA-N的固定化中底物淀粉对其水解活性有明显的保护作用,但对其转苷活性几乎无贡献.     

壳聚糖固定化乳酸脱氢酶的制备及酶学性质研究

以磁性壳聚糖作为载体,戊二醛作为交联剂,对乳酸脱氢酶(LDH)进行固定化.固定化的最适条件为:戊二醛浓度6%,pH值7.5,酶的偶联时间2 h.对游离及固定化LDH酶学性质的研究表明,酶促反应的最适pH值为9.2,最适温度分别为37℃和50℃,对乳酸的表观米氏常数分别为1.6 mmol/L和0.9 mmol/L.游离酶和固定化酶在40℃放置150 min后,其活力分别为最初的56.5%和76.1%.固定化酶在4℃贮存4周后,活力仍保留50%以上.固定化酶在室温下与底物重复反应6次后,活力仍保留60%以上,说明固定化酶具有较好的热稳定性、贮存稳定性和复用性.     

壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶及其性质

以具柔性亲水手臂的壳聚糖-精氨酸树脂为载体,用戊二醛交联胰凝乳蛋白酶,获得壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶. 最佳固定化条件为:m(酶)∶ m(载体)=20∶ 1 000、戊二醛体积分数为1.0%、pH=5.20、30 ℃交联60 min. 固定化酶活力达850 U/g,Km为1.83 mmol/L,比游离酶增大33.6%,比交联壳聚糖固定化酶低24.0%. 壳聚糖-精氨酸树脂固定化胰凝乳蛋白酶水解时间进程曲线与游离酶基本一致,均在反应30 min达到最大速率,最适温度为70 ℃,比游离酶升高10 ℃;在75 ℃时的半衰期可达6.0 h,比游离酶提高约4.3倍;最适pH值为5.92,比游离酶向酸性偏移2pH单位. 4 ℃贮存半衰期为49 d.     

聚酰胺-胺树状大分子修饰硅胶固定化胰蛋白酶的研究

以聚酰胺-胺(PAMAM)树状大分子修饰的硅胶为载体,胰蛋白酶为模型,考察了PAMAM的代数和固定化条件对酶的固载量及活力的影响.实验结果表明:选用3.0代PAMAM树状大分子修饰硅胶为载体固定化胰蛋白酶,酶促反应最适pH值为9.0,最适温度为60℃,对酪蛋白表现米氏常数K<,m>为7.76mg/mL,固定化胰蛋白酶表...     

化学修饰木瓜蛋白酶的固定化及性质研究

在底物保护和无底物保护下,用丁二酸酐对木瓜蛋白酶进行化学修饰,以三硝基苯磺酸法测定修饰酶的平均氨基修饰度,以棉布为载体,戊二醛为交联剂,对修饰前后的木瓜蛋白酶分别进行固定化.考察了温度、pH和表面活性剂SDS对化学修饰的固定化木瓜蛋白酶活力的影响,并与固定化天然木瓜蛋白酶进行了比较.研究表明,化学修饰固定化木瓜蛋白酶的最适反应温度为80℃;最适pH为9.0;在SDS浓度为20mg/mL时酶活也仍能保持在40%左右;米氏常数为187g/L.与天然的固定化酶相比,化学修饰的固定化木瓜蛋白酶的热稳定性、耐碱性和耐洗涤性得到了显著提高.     

巨大芽胞杆菌环氧水解酶的固定化及其催化性能

考察了多种载体对巨大芽孢杆菌ECU1001环氧水解酶的固定化.以大孔DEAE-纤维素离子交换树脂为载体时,固定化酶的活力回收达70%.进一步考察了温度和pH对固定化酶活力的影响,并使用该固定化酶进行了缩水甘油苯基醚对映选择性水解批次反应.结果表明,在较低的底物浓度下该固定化酶的稳定性较好,10批反应后仍然剩余72.4%的活力.     

海藻酸钠固定化根霉脂肪酶的制备及其性质

 研究了以海藻酸钠为载体,用包埋法制备固定化德氏根霉(Rhizopus delemar)脂肪酶的条件. 将酶粉和海藻酸钠溶于pH 5.0的HAc-NaAc缓冲溶液,用注射器将此混合液滴入到0.05 mol/L无菌CaCl2溶液中,静置固化45 min, 经过滤、洗涤和干燥后得到球状固定化酶. 固定化酶的活力回收约为34.1%. 酶学性质研究表明,此固定化酶的热稳定性较好. 游离酶在 60 ℃下保温1 h已完全丧失活力,而固定化酶在100 ℃下保温1 h仅损失36.2%的活力,在100 ℃下保温6 h仍可保持46.8%的酶活力. 酶经固定化后,其橄榄油水解反应的最适温度由40 ℃上升至90 ℃, Km值由13.8 mg/ml下降为8.1 mg/ml. 常见有机溶剂对固定化酶的活力影响较小. 将该固定化脂肪酶用于非水溶剂中正戊酸异戊酯的合成,重复使用6次后,固定化酶仍保持95%的酶活力.     

固定化扩展青霉脂肪酶的制备及其在玉米油转酯反应中的应用

采用吸附法对来源于扩展青霉Penicillium expansum的脂肪酶进行了固定化.从20种不同来源的树脂中筛选出固定化效率高且价格低廉的D4020树脂作为载体,系统研究了固定化条件对固定化效率及固定化酶转酯活力的影响.结果表明,最适加酶量、缓冲液pH和吸附时间分别为0.7 g/g、9.4和4 h.冻干时添加0.5%的半乳糖有助于提高固定化酶的转酯活力.在上述优化条件下,固定化酶的转酯活力为404.0 U/g,而所用的游离酶不能催化该转酯反应.利用该固定化酶催化玉米油转酯反应生产生物柴油时,叔戊醇为适宜的反应介质,其最适添加量为0.5 ml/g;适宜的酶量、加水量和反应温度分别为60.6 U/g、油重的1.2%和35℃.按醇/油摩尔比为1的比例分别在反应0、2和6 h时加入甲醇,在优化反应条件下,反应24 h后甲酯产率达85.0%;固定化脂肪酶具有较好的操作稳定性,反应10批次时,相对酶活力为62.8%.     

漆酶在纳米多孔金上的固定化及其酶学性质研究

利用纳米材料为载体对酶等生物大分子进行固定化近年来引起人们的浓厚兴趣. 以Au/Ag合金为原料, 通过控制浓硝酸的腐蚀时间再辅以退火处理得到了不同孔径的纳米多孔金(NPG), 利用扫描电镜(SEM)和N2气体吸附仪对孔性质进行了表征. 以NPG为载体, 用α-硫辛酸和N-乙基-N’-(3-二甲基氨基丙基)碳酰二亚胺/N-羟基琥珀酰亚胺(EDC/NHS)对金表面进行活化, 通过化学共价偶联的方法对产自Trametes versicolor的漆酶进行了固定化. 比较了孔径大小对酶固定化量及比活力的影响. 发现小孔径更有利于对该漆酶的固定化. 与游离酶相比, 固定化酶的最适pH没有改变, 但最适温度却从原来的40 ℃升到了60 ℃. 固定化后, 漆酶的pH和热稳定性都明显提高了. 重复使用8次仍能保持初始活力的65%, 且在4 ℃下保存1个月几乎观察不到酶活力的下降. 此外, 失活的固定化酶经浓硝酸处理后, NPG载体可重复利用. 本结果初步显示出了NPG在生物技术领域中的应用潜力.     

Combination of MALDI-TOF mass spectrometry with immobilized enzyme microreactor for peptide mapping

Matrix-assisted laser desorption/ionization mass spectrometry (MALDI-MS) has been combined with immobilized enzyme microreactor for the rapid, sensitive, and accurate tryptic mapping of protein and polypeptides. The technique utilizes the trypsin microreactor by immobilized enzyme on the glycidyl methacrylate (GMA)-modified cellulose membrane. The membrane micro-reactor was used for the tryptic mapping of cytochrome C and the results were compared with those obtained by using free trypsin. A significant increase in the overall sensitivity of the process was observed using the membrane microreactor, as well as the elimination of background signals due to the autolysis of the trypsin. Further, membrane microreactor digestions were found to be rapid and convenient.     

Immobilization of trypsin onto 1,4-diisothiocyanatobenzene-activated porous glass for microreactor-based peptide mapping by capillary electrophoresis: Effect of calcium ions on the immobilization procedure

The immobilization conditions and kinetic behaviour of trypsin, covalently immobilized via the 1,4-diisothiocyanatobenzene (DITC) linker onto aminopropylated controlled pore glass (CPG) particles, have been evaluated to establish a rapid and efficient protocol for fabrication of an immobilized enzyme microreactor (IMER) for protein hydrolysis and subsequent peptide mapping. Addition of calcium ions to either the immobilization reaction solution or hydrolysis assay was studied for a synthetic substrate. Activity was slightly higher when immobilization was carried out in the presence of Ca²⁺ whereas more enzyme could be immobilized in its absence. A protocol requiring less than 3 h was devised to obtain maximal enzymatic activity with the lowest ratio of soluble trypsin to DITC-CPG particles. The resulting immobilized enzyme was found to retain an acceptable percentage (ca. 35%) of its activity after immobilization. The particles were dry-packed into a capillary to make a microscale IMER. Repeatability, reusability and digestion efficiency of the μIMER were investigated for the substrate β-casein using capillary electrophoretic-based peptide mapping. In initial tests, a single device showed reproducible peptide maps for 21 digestions lasting 2 h each, carried out over a period of 2 months. Complete digestion of β-casein could be achieved in a few minutes (86 s residence time in the μIMER followed by a wash step).     

On-line characterization of the activity and reaction kinetics of immobilized enzyme by high-performance frontal analysis

A microreactor by immobilized trypsin on the activated glycidyl methacrylate-modified cellulose membrane packed column was constructed. Immobilized trypsin mirrored the properties of the free enzyme and showed high stability. A novel method to characterize the activity and reaction kinetics of the immobilized enzyme has been developed based on the frontal analysis of enzymatic reaction products, which was performed by the on-line monitoring of the absorption at 410 nm of p-nitroaniline from the hydrolysis of N-alpha-benzoyl-DL-arginine-p-nitroanilide (BAPNA). The hydrolytic activity of the immobilized enzyme was 55.6% of free trypsin. The apparent Michaelis-Menten kinetics constant (Km) and Vmax values measured by the frontal analysis method were, respectively, 0.12 mM and 0.079 mM min(-1) mg enzyme(-1). The former is very close to that observed by the static and off-line detection methods, but the latter is about 15% higher than that of the static method. Inhibition of the immobilized trypsin by addition of benzamidine into substrate solution has been studied by the frontal analysis method. The apparent Michaelis-Menten constant of BAPNA (Km), the inhibition constant of benzamidine (Ki) and Vmax were determined. It was indicated that the interaction of BAPNA and benzamidine with trypsin is competitive, the Km value was affected but the Vmax was unaffected by the benzamidine concentration.     

Vinyl functionalized silica hybrid monolith-based trypsin microreactor for on line digestion and separation via thiol-ene "click" strategy

A novel thiol-ene "click" strategy for the preparation of monolithic trypsin microreactor was proposed. The hybrid organic-inorganic monolithic capillary column with ene-functionality was fabricated by sol-gel process using tetramethoxysilane (TMOS) and γ-methacryloxypropyltrimethoxysilane (γ-MAPS) as precursors. The disulfide bonds of trypsin were reduced to form free thiol groups. Then the trypsin containing free thiol groups was attached on the γ-MAPS hybrid monolithic column with ene-functionality via thiol-ene click chemistry to form a trypsin microreactor. The activity of the trypsin microreactor was characterized by detecting the substrate (Nα-p-tosyl-L-arginine methyl ester hydrochloride, TAME) and the product (Nα-p-tosyl-L-arginine, TA) with on-line capillary zone electrophoresis. After investigating various synthesizing conditions, it was found that the microreactor with poly(N,N'-methylenebisacrylamide) as spacer can deliver the highest activity, yielding a rapid reaction rate. After repeatedly sampling and analyzing for 100 times, the monolithic trypsin microreactor still remained 87.5% of its initial activity. It was demonstrated that thiol-ene "click" strategy for the construction of enzyme microreactor is a promising method for the highly selective immobilization of proteins under mild conditions, especially enzymes with free thiol radicals.     

Immobilization of Horseradish Peroxidase on Nonwoven Polyester Fabric Coated with Chitosan

The immobilization of horseradish peroxidase (HRP) on composite membrane has been investigated. This membrane was prepared by coating nonwoven polyester fabric with chitosan glutamate in the presence of glutraldehyde as a crosslinking agent. The physico-chemical properties of soluble and immobilized HRP were evaluated. The soluble HRP lost 90% of its activity after 4 weeks of storage at 4°C, whereas the immobilized enzyme retained 85% of its original activity at the same time. A reusability study of immobilized HRP showed that the enzyme retained 54% of its activity after 10 cycles of reuse. Soluble and immobilized HRP showed the same pH optima at pH 5.5. The immobilized enzyme had significant stability at different pH values, where it had maximum stability at pH 3.0 and 6.0. The kinetic properties indicated that the immobilized enzyme had more affinity toward substrates than soluble enzyme. The soluble and immobilized enzymes had temperature optima at 30 and 40°C and were stable up to 40 and 50°C, respectively. The stability of HRP against metal ion inactivation was improved after immobilization. Immobilized HRP exhibited high resistance to proteolysis by trypsin. The immobilized HRP was more resistant to inactivation induced by urea, Triton X-100, and organic solvents compared to its soluble counterpart. The immobilized HRP showed very high yield of immobilization and markedly high stabilization against several forms of denaturants that offer potential for several applications.     

Immobilization of trypsin on sub-micron skeletal polymer monolith

A new kind of immobilized trypsin reactor based on sub-micron skeletal polymer monolith has been developed. Covalent immobilization of trypsin on this support was performed using the epoxide functional groups in either a one- or a multi-step reaction. The proteolytic activity of the immobilized trypsin was measured by monitoring the formation of N-α-benzoyl-L-arginine (BA) which is the digestion product of a substrate N-α-benzoyl-L-arginine ethyl ester (BAEE). Results showed that the digestion speed was about 300 times faster than that performed in free solution. The performance of such an enzyme reactor was further demonstrated by digesting protein myoglobin. It has been found that the protein digestion could be achieved in 88 s at 30°C, which is comparable to 24 h digestion in solution at 37°C. Furthermore, the immobilized trypsin exhibits increased stability even after continuous use compared to that in free solution. The present monolithic enzyme-reactor provides a promising platform for the proteomic research.     

The properties of covalently immobilized trypsin on soap-free P(MMA-EA-AA) latex particles

The covalent immobilization of trypsin onto poly[(methyl methacrylate)-co-(ethyl acrylate)-co-(acrylic acid)] latex particles, produced by a soap-free emulsion polymerization technique, was carried out using the carbodiimide method. The catalytic properties and kinetic parameters, as well as the stability of the immobilized enzyme were compared to those of the free enzyme. Results showed that the optimum temperature and pH for the immobilized trypsin in the hydrolysis of casein were 55 degrees C and 8.5, both of which were higher than that of the free form. It was found that K(m) (Michaelis constant) was 45.7 mg . ml(-1) and V(max) (maximal reaction rate) was 793.0 microg . min(-1) for immobilized trypsin, compared to a K(m) of 30.0 mg . ml(-1) and a V(max) of 5 467.5 microg . min(-1) for free trypsin. The immobilized trypsin exhibited much better thermal and chemical stabilities than its free counterpart and maintained over 63% of its initial activity after reusing ten times.     

Application and properties of butyl acrylate/pentaerythrite triacrylate copolymers and cellulose-based Granocel as carriers for trypsin immobilization

The main point was the search for a proper carrier and the kind of carrier activation for trypsin (EC 3.4.21.4) immobilization. The acrylic and cellulose-based carriers were specially prepared in that they possessed the most often used anchor groups: -OH, -NH(2), DEAE and/or -COOH. The immobilization procedures were selected to apply mainly to protein amine groups and appropriate anchor groups on the carrier. As activity tests low (N-benzoyl-dl-arginine-p-nitroanilide, BAPNA) and high (casein) molecular weight substrates were used. It was found, as a rule, that trypsin bound to -COOH groups with the help of carbodiimide was less active and that the amount of bound protein and measured activity (BAPNA) are considerably higher when protein is immobilized via divinyl sulfone. Both rules were observed irrespective of the nature of the polymer matrix. Both types of carriers were found suitable for trypsin immobilization and they were far better than the corresponding Eupergit C-bound enzyme preparations. Taking into account storage stability and activity for both substrates, the divinylsulfone linkage formed between unmodified Granocel and trypsin was the most effective method for the enzyme immobilization. For this preparation, BAPNA and casein conversion, thermal stability at 60 degrees C and estimated kinetic parameters were compared with those obtained for the native enzyme. It was shown that mass transport limitations could be effectively eliminated by suitable conditions and immobilized trypsin was considerably more stable. The values k(cat)/K(m) indicated that the immobilized enzyme was even better as amidase activity was regarded and its potential for protein hydrolysis was only less than twice.     

A Trypsin Immobilized Sol-Gel for Protein Indentification in MALDI-MS Applications

The proteolytic enzyme trypsin was chemically immobilized to an amine-functionalized sol-gel using adipoyl chloride under nonaqueous conditions and a nitrogen atmosphere. In the synthesis of the sol-gel, tetraethyl orthosilicate (TEOS), and 3-(2-aminoethylamino) propyldimethoxymethylsilane (AEAPMS) (50:50, v/v) were used, which provided convenient physical and chemical conditions to maintain catalytic activity of immobilized trypsin molecules for the digestion of proteins in proteomics applications. Bovine serum albumin was used as a model protein to perform enzymatic digestion using the trypsin immobilized sol-gel. The resulting peptides were analyzed by matrix-assisted laser desorption/ionization-mass spectrometry to evaluate the digestion performance and specificity of the sol-gel material. The trypsin immobilized sol-gel showed superior enzymatic activity in protein digestion and it was determined that the sol-gel material could be repeatedly used at least 25 times without significant activity loss in long-term use. Additionally, autocatalysis was prevented by immobilization of trypsin. The peptide digest having the highest purity was obtained for protein identification studies.     

基于DNA链置换反应的新型固定化酶反应器制备及应用

建立了一种新型的酶固定化方法,采用DNA链置换反应成功地在单链DNA标记的磁性纳米粒子上实现了酶的链置换无损更替。该技术可实现目标酶的再利用,节约了生产成本。制备的固定化胰蛋白酶微反应器具有较好的重复利用性和高酶切效率,重复使用10次后仍可保持原酶活性的86%;利用链置换反应制备的MNPs@DNATrypsin酶切马心肌红蛋白5 min后,即可获得95%±0%(n=3)的氨基酸序列覆盖率,远超过相同条件下自由酶酶切12 h的结果。实验表明,发展的固定化酶技术具有高磁响应性,便于从反应体系中回收固定化酶和重复使用,同时此技术可显著提高酶活性,因此可用于固定各种重要的酶,同时可将其广泛应用于各种酶促反应中。