首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 59 毫秒
1.
用阳离子交换树脂CM-52分离纯化类人胶原蛋白Ⅱ(Human Collagen-like Bioprotein Ⅱ,HCBⅡ)。通过实验,分别确定了静态吸附和柱层析吸附的操作条件,即静态吸附:在pH4.0、NaCl0.15mol/L、进料浓度7g/L,处理量17.26ml/g树脂的条件下进行吸附,吸附时间为60min;柱层析:在pH4.0、NaCl0.15mol/L、进料浓度5g/L、流速5ml/min的条件下进行吸附。然后上柱,在pH4.0、NaCl0.30mol/L下进行脱附。实验表明,采用静态吸附的方式吸附HCBⅡ,然后上柱洗脱,HCBⅡ的吸附量可达到48、6mg/g树脂,回收率83.8%,操作时间短,分辨率高,最终纯化的HCBⅡ达电泳纯,分子量为97kD。  相似文献   

2.
大孔吸附树脂提取麦拓莱霉素的工艺研究   总被引:4,自引:0,他引:4  
研究了用大孔吸附树脂从发酵液中分离提取新型大环内酯类抗生素-麦拓莱霉素的吸附工艺过程,对吸附条件进行了优化,得到了适宜的操作条件.结果表明:NKA树脂为最佳吸附剂:吸附最佳pH值为10.32;吸附流速选择为1ml/min;NaCl的加入对吸附不利,选择NaCl浓度为0.6%左右,本实验条件下,发酵液中的麦拓莱霉素浓度为0.18mg/ml;NKA的吸附量可达33.7mg/g树脂。  相似文献   

3.
用离子交换树脂法吸附柠檬酸溶液中的金属离子,苯乙烯系阳离子交换树脂的吸附性能较好,它对镍、铝离子的吸附容量均较大,且吸附前后柠檬酸溶液的浓度变化较小.静态条件下树脂对镍的吸附容量为16.83mg Ni/g干树脂,对铝为21.36mg Al/g干树脂;动态条件下树脂对镍的吸附容量为6.78mg Ni/g干树脂,对铝为31.8mgAl/g干树脂,吸附液流速为1m/h~3m/h.吸附后的柠檬酸溶液可循环使用.当用1mol/L硫酸解吸时,树脂对镍铝的解吸率可达90%以上.当硫酸中Ni2 为1.70mmol/L,Al3 为7.40mmol/L时,树脂的解吸率仍可达80%以上.  相似文献   

4.
吸附树脂对紫背天葵的水溶性色素精制研究   总被引:3,自引:0,他引:3  
研究吸附树脂吸附精制紫背天葵红色素的方法和工艺。以吸附量、解吸量为指标,在pH=7时吸附,确定出S-8极性树脂和盐酸-乙醇溶液为最佳吸附剂和解吸剂。正交动态吸附和解吸实验结果表明,当原花液浓度3g/L,吸附流速3ml/min,树脂床层径高比1:1时,树脂对色素的吸附量最大;以盐酸-乙醇为解吸剂,解吸液用量30ml/g,解吸流速是1/5BV。经树脂吸附精制后的色素色价是未精制色素的3.74倍。  相似文献   

5.
研究了利用批量离子交换层析与凝胶过滤层析相结合的方法纯化类人胶原蛋白I的最佳条件。分别考察了不同离子交换树脂、缓冲溶液pH、离子强度、进料蛋白浓度对批量离子交换的影响,以及不同凝胶过滤介质对凝胶过滤层析的影响。结果表明,采用阴离子交换树脂DEAE52吸附杂蛋白,缓冲液pH为7.0,NaCl浓度为0.2mol/L,进料蛋白浓度为40mg/mL,并采用凝胶过滤介质SephadexG-100进一步纯化后,类人胶原蛋白I的纯度可达到98.2%,总纯化倍数为3.1,总回收率为80.6%。SDS-PAGE分子量分析和N末端氨基酸序列分析均表明纯化后的类人胶原蛋白I与基因设计一致。  相似文献   

6.
D301R树脂吸附-解吸钼的行为研究   总被引:3,自引:0,他引:3  
对D301R型阴离子交换树脂吸附-解吸钼的条件进行了研究,采用静态法试验了pH值、钼的浓度等因素对该树脂吸附钼的影响;采用动态法讨论了该树脂对钼的饱和吸附量、解吸剂及其浓度对解吸钼的影响。结果表明在pH2.5,钼的浓度为20g/L时吸附效果最好,树脂对钼的饱和吸附量为1020mg/g,而采用150g/L NaOH溶液解吸钼效果最佳。  相似文献   

7.
考察了NKA-9、S-8、XDA-1、AB-8、HPD-100、HPD-600 6种大孔吸附树脂对宁夏枸杞总黄酮的吸附和解吸性能,筛选出XDA-1树脂的效果最佳;考察了pH值、样液浓度、流速等对XDA-1树脂静态吸附效果的影响;并进行了动态吸附试验,确定出XDA-1树脂动态吸附枸杞总黄酮的最佳条件:样品液浓度为0.25mg/mL,控制流速为0.5mL/min,样品液pH 5;最佳洗脱条件:洗脱液为80%的乙醇水溶液,用量为35mL (5倍柱床体积).在此条件下,枸杞总黄酮含量从27.2%提高到79.8%,回收率为87.4%,表明XDA-1树脂可用于宁夏枸杞总黄酮的分离纯化.  相似文献   

8.
研究了D315大孔阴离子交换树脂从酸性含金氯化溶液中吸附金的性能,考察了吸附时间,pH值,温度,阴离子浓度等因素对树脂吸附金的影响.结果表明,在pH=2时树脂的吸附效果最佳,静态饱和吸附容量可达到228.80mg/g(Au/干树脂),温度越高越有利于吸附,吸附反应热焓△H=11.30kJ/mol.吸附平衡服从Freundish吸附等温式.用8%硫脲-1mol/L硫酸可以将树脂上的金完全解析.  相似文献   

9.
考察了HPD-826、HPD-417、ADS-17、HPD-722、HPD-450、AB-8、HPD-600、D-101,共8种大孔树脂对藏药白花龙胆花总黄酮的吸附和解吸性能,通过静态吸附量和解吸附率及静态吸附曲线的绘制,筛选出AB-8树脂的效果最佳;以AB-8树脂为目标,进行了动态吸附实验,考察了上柱液浓度、pH值、上柱液流速、乙醇浓度、解吸剂流速、解吸体积等对AB-8树脂吸附和解吸效果的影响,确定出AB-8树脂动态吸附白花龙胆花总黄酮的最佳条件:上柱液浓度为6.5mg/mL,pH为3.79,上柱流速4BV/h;最佳洗脱条件:用50%乙醇进行洗脱,解吸流速为3BV/h,解吸体积4BV。在此条件下,白花龙胆花总黄酮纯度由原来的22.10%,变为65.75%,产品精制倍数为65.75%/22.10%=2.97,表明AB-8树脂可用于白花龙胆花总黄酮的分离纯化。  相似文献   

10.
用交联的壳聚糖微球(CTS)与氯乙酸在碱性条件下反应,合成了羧甲基壳聚糖树脂(CMCT)。其吸附染料活性艳红X-3B的实验结果表明,CMCT和CTS均对偶氮染料活性艳红X-3B有较好的去除能力。实验条件下,最大平衡吸附量分别为611.5mg/g和365.2mg/g,说明羧甲基的引入提高了壳聚糖的吸附能力。等温吸附可以用Langmuir方程较好的描述,表明为单分子层吸附。动力学过程用二级吸附动力学模拟具有很好的线性相关性,通过二级吸附模型计算出的平衡吸附量与实验值相符。流动床实验表明,CMCT和CTS对浓度为100mg/L的X-3B溶液吸附的穿透点分别为6000ml/g和3375ml/g,用0.1mol/L的氢氧化钠溶液洗脱,洗脱峰集中,洗脱率都在90%以上。洗脱再生后的CMCT和CTS树脂均可重复使用。  相似文献   

11.
用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.  相似文献   

12.
Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.  相似文献   

13.
A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.  相似文献   

14.
The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp3)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp2)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp2)?H and aliphatic 1,5- and 1,6-C(sp3)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp3)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp2)?H insertion.  相似文献   

15.
A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.  相似文献   

16.
In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.  相似文献   

17.
A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.  相似文献   

18.
N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).  相似文献   

19.
An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y1 and Y2. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.  相似文献   

20.
In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号