聚焦Ga~ 离子束注入方法研制半导体量子线结构

采用聚焦Ga~ 离子束注入方法,在GaAs/Al_(0.3)Ga_(0.7)As多量子阱材料上尝试制备半导体量子线。通过低温光致发光谱,测量了量子线的光电特性,并观察了由于沟道效应导致的深层量子阱的光谱蓝移。     

Si杂质扩散诱导InGaAs/AlGaAs量子阱混杂的研究（英文）

光学灾变损伤(COD)常发生于量子阱半导体激光器的前腔面处,极大地影响了激光器的出光功率及寿命。通过杂质诱导量子阱混杂技术使腔面区波长蓝移来制备非吸收窗口是抑制腔面COD的有效手段,也是一种高效率、低成本方法。本文选择了Si杂质作为量子阱混杂的诱导源,使用金属有机化学气相沉积设备生长了InGaAs/AlGaAs量子阱半导体激光器外延结构、Si杂质扩散层及Si 3 N 4保护层。热退火处理后,Si杂质扩散诱导量子阱区和垒区材料互扩散,量子阱禁带变宽,输出波长发生蓝移。退火会影响外延片的表面形貌,而表面形貌则可能会影响后续封装工艺中电极的制备。结合光学显微镜及光致发光谱的测试结果,得到825℃/2 h退火条件下约93 nm的最大波长蓝移量,也证明退火对表面形貌的改变,不会影响波长蓝移效果及后续电极工艺。     

荧光法测定半导体禁带宽度

光学带隙或禁带宽度是半导体材料的一个重要特征参数.本文以3个具有代表性的InGaN/GaN多量子阱结构作为研究对象,深入探讨了荧光法测定某个目标温度下InGaN阱层的光学带隙所需要满足的测试条件.由于InGaN阱层是一种多元合金且受到来自GaN垒层的应力作用,所以该阱层中不仅存在着杂质/缺陷相关的非辐射中心,也存在着组分起伏诱发的局域势起伏以及极化场诱发的量子限制斯塔克效应.因此,为了获得目标温度下InGaN阱层的较为精确的光学带隙,提出了荧光测量至少应满足的测试条件,即必须消除该目标温度下非辐射中心、局域中心以及量子限制斯塔克效应对辐射过程的影响.     

聚焦Ga+离子束注入方法研制半导体量子线结构

采用聚焦Ga⁺离子束注入方法,在GaAs/Al_0.3Ga_0.7As多量子阱材料上尝试制备半导体量子线。通过低温光致发光谱,测量了量子线的光电特性,并观察了由于沟道效应导致的深层量子阱的光谱蓝移。 关键词：     

Zn杂质扩散诱导AlGaInP/GaInP量子阱混杂

杂质扩散诱导量子阱混杂技术可用于制作腔面非吸收窗口,提高大功率半导体激光器的输出功率.以Zn2As2为扩散源,采用闭管扩散方式,在550℃下对650 nm半导体激光器的外延片进行了一系列Zn杂质扩散诱导量子阱混杂的实验.实验发现,随着扩散时间从20～120 min,样品光致发光(PL)谱蓝移偏移增加,峰值波长蓝移53 nm;当扩散时间超过60 min后,样品的PL谱中不仅出现了常见的蓝移峰,同时还出现了红移峰,峰值波长红移32 nm.分析表明PL谱蓝移来自Zn扩散引起的AlGaInP/GaInP间的量子阱混杂;红移来自Zn杂质扩散对样品中Ga0.51In0.49P缓冲层的影响.还研究了扩散温度(550℃)和扩散时间对样品晶体品质的影响,并在理论上计算了AlGaInP/GaInP量子阱混杂巾的Al-Ga的互扩散系数.     

量子阱在沿其平面方向偏振太赫兹波驱动下子带间光吸收

利用半导体布洛赫方程,讨论了量子阱在沿其平面方向偏振的太赫兹场驱动下的光学吸收谱。研究结果揭示了半导体量子阱在沿平面方向偏振的强太赫兹场驱动下吸收谱的一些新奇效应,如主吸收的太赫兹边带、动态弗兰兹-凯尔迪什效应。太赫兹场的频率及其相位对探测场吸收谱的影响也很显著。     

GaAs/AlxGa1-xAs量子阱能级结构设计与光谱分析

通过理论计算对用于量子阱红外探测器的GaAs/AlxGa1-xAs量子阱能级结构进行模拟设计,将不同生长结构的量子阱材料的光响应谱和光致荧光谱(PL)与计算结果进行比较.说明量子阱生长结构与量子阱能级结构的关系.欲使量子阱红外探测器的响应峰值在8μm附近,则需量子阱结构中阱宽为47nm,垒中Al含量为029.理论计算与测试结果符合得较好. 关键词：     

左手介质对一维光量子阱透射谱的影响

通过传输矩阵法理论研究左手介质对一维光子晶体量子阱(AB)m(CBAABC)n(BA)m透射谱的影响,结果发现:当C层为双正介质时,光量子阱透射谱中出现2n+1条窄透射峰,当C层为左手介质时,呈现简并现象,光量子阱透射峰中仅出现2n-1条窄透射峰;当C层左手介质折射率负值增大时,光量子阱透射谱向禁带中心两侧移动,同时透射峰快速变窄;当C层左手介质光学厚度负值减小时,光量子阱透射谱向禁带中心靠拢,同时透射峰迅速变窄;光量子阱透射变窄对左手介质光学厚度的响应灵敏度高于对折射率负值的响应。左手介质对光量子阱透射谱特性的影响规律,可为光子晶体理论研究及新型量子光学器件设计提供参考。     

PbTe/CdTe量子阱光学性质的研究

PbTe/CdTe量子阱是一类新型异系低维结构材料,实验观察到具有强的室温中红外光致发光现象.建立了理论模型,计算了PbTe/CdTe量子阱的自发辐射率和光学增益.模型中量子阱分立能级的计算采用k·p包络波函数方法和有限深势阱近似,考虑了PbTe能带结构的各项异性和阱层中应变对能级的影响.计算了PbTe/CdTe量子阱自发辐射谱与带间弛豫和注入载流子浓度间的依赖关系,计算结果与实验观察到的光致发光峰相符合.自发辐射谱线峰位随着注入载流子浓度的增加而出现蓝移,当载流子浓度从2×1017cm-3增加到2.8×1018cm-3,基态发射峰从372 meV蓝移到397 meV,而第一激发态发射峰蓝移量为15 meV.上述蓝移现象是由载流子与载流子及载流子与声子间的相互作用引起的.与PbTe体材料相比.PbTe/CdTe量子阱结构具有更高的增益强度(提高近15倍)和更宽的增益区,因而该体系可能是实现室温连续工作的中红外激光器的理想材料.     

空穴在动量空间分布对p型量子阱红外探测器响应光谱的影响

通过对p型量子阱红外探测器(QWIP)的自洽计算，得到了量子阱价带的电子结构和器件的光电流谱，并研究了载流子在动量空间分布对p型QWIP光谱响应的影响.计算结果表明，在动量空间不同区域的空穴对器件的光谱响应起着不同作用，从而使得在p型QWIP中，空穴浓度和温度都将影响器件的响应光谱.所得结果合理地解释了实验中器件响应光谱随掺杂浓度和温度的变化. 关键词： p型量子阱红外探测器 响应光谱 空穴浓度 温度     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.