牛血清白蛋白在超薄纳米二氧化钛膜表面的印迹与吸附

基于溶胶凝胶分子印迹方法,以溶胶二氧化钛TiO2为基质印迹了牛血清白蛋白分子。用1%的NaOH溶液可有效地除去纳米TiO2印迹膜中的模板分子。采用石英晶体微天平现场技术,研究了牛血清白蛋白在超薄纳米TiO2膜表面的吸附行为。研究表明,牛血清白蛋白在印迹膜和非印迹膜上的吸附量都随溶液浓度增加而增大,印迹膜具有吸附的特异性和可再生性,其吸附量是非印迹膜的3~5倍;在非印迹膜上的吸附符合Langmuir吸附模型,而在印迹膜上的吸附符合allosteric吸附模型;牛血清白蛋白在非印迹膜上的吸附量先随pH升高而增大,当pH为5左右时达到最大值,随后吸附量又随pH的增大而减小;而在印迹膜上其吸附量仅随pH增大而增大。     

基于表面等离子体共振技术的血清白蛋白与色氨酸对映异构体手性识别的热力学研究

利用表面等离子体共振(SPR)技术,从热力学角度研究了牛血清白蛋白、人血清白蛋白与色氨酸对映异构体相互作用的手性识别,考察了p H值、离子强度和温度对亲和力的影响.利用热力学方法计算并探讨了作用机理.实验结果表明,牛血清白蛋白及人血清白蛋白与L-色氨酸的结合有高度特异性.热力学参数计算结果证明疏水作用在手性识别过程中起主要作用,但不排除静电作用有一定的贡献.     

PAN-蛋白质络合物的极谱吸附波及其应用

在0.05 mol/L HAc溶液中,PAN-牛血清白蛋白/人血清白蛋白络合物在-0.58 V(vs.SCE)处产生一灵敏吸附还原峰,峰电位较之游离PAN还原峰负约0.28 V,峰电流与牛血清白蛋白、人血清白蛋白浓度在0.1～12 mg/L,0.1～11 mg/L范围内呈线性关系;检测限均为0.05 mg/L。运用该法测定了人血清样品蛋白质含量。     

激光光散射与荧光光谱法研究大豆苷与牛血清白蛋白作用及聚集态

荧光光谱法和动态光散射法研究大豆苷与牛血清白蛋白在生理条件下的相互作用. 研究表明, 大豆苷与牛血清白蛋白能形成2∶l复合物, 荧光猝灭属于静态猝灭过程; 大豆苷与牛血清白蛋白分子间主要的结合作用力为疏水作用; 310 K下, 两者结合常数和结合位点数分别为7.4×l04 L•mol―1和1.75; 大豆苷使牛血清白蛋白的构象发生了变化; 动态光散射数据探讨了牛血清白蛋白与大豆苷分子产生聚集与之相互作用, 进一步证实了牛血清白蛋白在大豆苷水溶液中的构象变化. 实验结果为进一步研究大豆苷对心血管疾病的药理作用, 特别是对血浆蛋白构象的影响提供了重要依据.     

核壳纳米粒子与牛血清白蛋白表面增强拉曼光谱的研究

本文用表面增强拉曼光谱(SERS)系统地研究了牛血清白蛋白(BSA)与Ag/Pt核壳纳米粒子的相互作用,特别是核壳纳米粒子与被吸附的牛血清白蛋白分子之间的界面作用,并用紫外可见光谱、圆二色光谱(CD)作为辅助手段进一步证实了BSA与核壳纳米粒子的作用状况.通过紫外光谱研究发现,核壳纳米粒子的特征吸收峰的消失表明纳米粒子完全被牛血清白蛋白包覆.用近紫外CD光谱探讨了血清白蛋白的芳基氨基酸(苯丙氨酸、酪氨酸)残基微环境的变化.为探讨牛血清白蛋白与Ag/Pt核壳纳米粒子的作用机理及纳米尺寸的生物效应奠定了理论基础.     

光学活性偶氮苯自组装膜的制备及其蛋白吸附行为

研究了在紫外光作用下, 牛血清白蛋白(BSA)在偶氮苯自组装膜上光控可逆的吸附行为. 首先合成羧基偶氮苯衍生物, 并在金膜表面制备偶氮苯自组装膜, 采用紫外吸收光谱(UV)、原子力显微镜(AFM)观察偶氮苯衍生物的光学顺反异构现象以及偶氮苯自组装膜表面形貌的变化. 同时利用等离子体表面谐振仪(SPR)考察偶氮苯光学异构对牛血清白蛋白(BSA)在自组装膜表面上的吸附行为的影响. 结果表明, BSA在偶氮苯自组装膜表面的吸附作用主要来自于BSA分子与自组装膜之间的静电作用及亲疏水作用. 在紫外光作用下, 偶氮苯自组装膜可以实现光控可逆的牛血清白蛋白分子吸附行为.     

荧光光度法研究甲氨蝶呤和蛋白质的相互作用

应用荧光光度法研究了水溶液中甲氨蝶呤与牛血清白蛋白以及人血清白蛋白分子间的结合反应,讨论了甲氨堞呤对蛋白质内源荧光的猝灭机理,测定出甲氨蝶呤与牛血清白蛋白以及人血清白蛋白的结合常数分别为6.76×105L·mol-1,2.69×105L·mol-1,相应的结合位点数分别为1.09,1.02.依据F(o)rster非辐射能量转移理论确定了供体-受体间的结合距离和能量转移效率,并用同步荧光技术考察了甲氨蝶呤对蛋白质构象的影响.     

光谱法结合分子对接研究血清蛋白对吴茱萸次碱的识别作用

利用荧光光谱法与分子对接模拟计算系统地研究了吴茱萸次碱同牛血清白蛋白及人血清白蛋白间相互作用情况。荧光光谱实验结果表明,在37℃及生理p H条件下的水溶液中,吴茱萸次碱可以有效地猝灭牛血清白蛋白与人血清白蛋白的荧光发射。根据Stem-Volmer方程及双对数方程计算可知,吴茱萸次碱对牛血清蛋白与人血清白蛋白的荧光猝灭均为静态猝灭,吴茱萸次碱可以同这两种蛋白质形成1:1型稳定的复合物。采用了恒波长同步荧光法研究了吴茱萸次碱与这两种血清蛋白可能的结合位点,并且通过分子对接模拟计算方法推测了吴茱萸次碱与这两种血清蛋白可能的结合模型,结果表明,吴茱萸次碱与血清蛋白最有可能的结合位点为Trp213残基(牛血清白蛋白)或Trp214残基(人血清白蛋白)附近。     

变色酸与牛血清白蛋白的相互作用

采用荧光光谱法和紫外-可见分光光度法研究了变色酸与牛血清白蛋白之间的相互作用。结果表明:变色酸对牛血清白蛋白有较强的荧光猝灭作用。根据Stern-Volmer方程得到了荧光猝灭常数,并判断由于与变色酸反应而导致牛血清白蛋白的荧光猝灭属于静态猝灭。采用Lang-muir单分子吸附模型计算了结合常数和结合位点数。从计算得到的热力学参数ΔH和ΔS推断了变色酸与血清白蛋白反应的作用力为氢键和范德华力。     

磷酸钙陶瓷颗粒微纳米结构对蛋白吸附的影响

用微波烧结和常规烧结方法分别制备了4种具有纳米和微米结构的磷酸钙陶瓷, 对陶瓷的相组成、 微观结构、 粒度分布、 比表面积、 孔径分布和表面Zeta电位进行了对比分析, 并进一步采用凝胶电泳法考察了陶瓷对牛血清白蛋白/溶菌酶双蛋白的吸附行为. 结果显示, 纳米陶瓷和常规陶瓷具有相似的相组成、 颗粒分布和表面Zeta电位, 但微孔结构、 比表面积和蛋白吸附差异明显. 纳米陶瓷具有较小的晶粒尺寸和更丰富的介孔结构, 使其能吸附更多的牛血清白蛋白和溶菌酶, 表明其具有更强的生物活性.     

粘度法研究明胶在聚氨酯弹性体表面的吸附

根据文献以异佛尔酮二异氰酸酯（IPDI）为原料制备了具有较好机械性能的聚氨酯弹性体胶条（PU）,并在胶条表面接枝肝素,得到肝素化聚氨酯胶条（PU-Hep）。将聚氨酯胶条浸泡在明胶稀溶液中,测量溶液粘度随时间、溶液浓度和温度的变化,并采用具有界面校正的粘度方程从实验相对粘度数据计算明胶在聚氨酯表面的吸附量。研究发现明胶分...     

可生物降解的聚乳酸弹性体的性能研究

对制备的聚乳酸（聚醚）酯型聚氨酯弹性体进行了动态力学、力学性能和降解性能的测试．结果表明，弹性体的强度和弹性都较好，它们受交联度、ＰＥＧ含量和ＰＥＧ分子量的影响．该弹性体的降解速度较快．降解过程中存在自催化效应，而且是从表面开始由表及里逐渐降解的．但材料降解过程中也会出现内部降解较快的现象．动物实验表明，该弹性体是一种能满足尿道支撑管要求的有实际应用价值的材料．     

Autohesion and adhesion in filled elastomers,the role of mechanical breakdown processes

The paper discusses the influence of fillers on formation of the contact surface and on interface action in autohesive and adhesive joining of elastomers and plasticates. The formulated laws and effects refer to intensification of the mechanical breakdown of the elastomer during milling, accompanied by modification of its molecular structure as well as adsorption and binding of the macromolecules plus formation of elastomer-filler gels. The information shows that fillers are capable of either impairing or improving the autohesive and adhesive properties of the compound, according to the relative contribution of two opposing processes: reduction (to a certain limit) of the molecular weight, whereby the molecular contact is increased, and interdiffusion or adsorptive binding of the macromolecules accompanied by gel formation, whereby the autohesive and adhesive properties are impaired. The oxidation associated with mechanical breakdown intensifies interface action, but retards the rheological processes of contact-surface formation.     

Comparison of the characteristics of polyurethane elastomers based on DMC- and traditional polyethers

The results of the study of replacement of traditional polyether polyols with DMC polyols based on the new DMC technology in formulas of polyurethane (PU) elastomer adhesives and sealants are presented. It is shown that the physical and mechanical characterisrics of PU elastomers are improved in many cases.     

Synthesis, characterization and mechanical properties of polyester-based aliphatic polyurethane elastomers containing hyperbranched polyester segments

Aliphatic polyester-based polyurethane (PU) elastomers with hyperbranched polyester segments were synthesized from polyester diol, hydroxyl-terminated hyperbranched polyester (HB-20), isophorone diisocyanate (PDI) and 1,4-butanediol. The crosslinking density of the PU elastomer was calculated by using Flory-Rehner equation. The degree of hydrogen bonding, the microstructure and the morphologies of these PU materials were characterized by means of FT-IR, WAXD and DSC, respectively. The experimental results showed that the PU elastomers containing small amount of HB-20 exhibited the enhanced hydrogen bonding and mechanical properties. As compared with the comparable PU specimen, the tensile strength of the polyester-based aliphatic PU containing 6 wt% HB-20 increased by 71.2 times, up to 36.1 MPa, and the elongation at break was still as high as 333.1%, resulting from the dual effects of the hydrogen bonding and the crosslinking density in the PU system.     

Thermal degradation studies of polyurethane/POSS nanohybrid elastomers

Reported here is the synthesis of a series of polyurethane/POSS nanohybrid elastomers, the characterisation of their thermal stability and degradation behaviour at elevated temperatures using a combination of thermogravimetric Analysis (TGA) and thermal volatilisation analysis (TVA). A series of PU elastomer systems have been formulated incorporating varying levels of 1,2-propanediol-heptaisobutyl-POSS (PHIPOSS) as a chain extender unit, replacing butane diol. The bulk thermal stability of the nanohybrid systems has been characterised using TGA. Results indicate that covalent incorporation of POSS into the PU elastomer network increases the non-oxidative thermal stability of the systems. TVA analysis of the thermal degradation of the POSS/PU hybrid elastomers have demonstrated that the hybrid systems are indeed more thermally stable when compared to the unmodified PU matrix; evolving significantly reduced levels of volatile degradation products and exhibiting a ∼30 °C increase in onset degradation temperature. Furthermore, characterisation of the distribution of degradation products from both unmodified and hybrid systems indicate that the inclusion of POSS in the PU network is directly influencing the degradation pathways of both the soft and hard-block components of the elastomers: The POSS/PU hybrid systems show reduced levels of CO, CO₂, water and increased levels of THF as products of thermal degradation.     

具有超支化结构的聚醚型脂肪族聚氨酯弹性体的合成与表征及力学性能研究

用聚四氢呋喃醚二醇、端羟基超支化聚酯(HB-20)、异佛尔酮二异氰酸酯和1,4-丁二醇,合成了含有超支化结构的聚醚型脂肪族聚氨酯(PU)弹性体.通过Flory-Rehner公式计算了体系的交联密度;用FT-IR、WAXD和DSC表征了超支化PU的氢键化程度和形态.实验结果表明,在PU弹性体中引入少量的HB-20,能提高氨基甲酸酯羰基的氢键化程度和软硬段间的微相分离程度,从而显著提高材料的拉伸强度.由于氢键化程度和交联密度双重效应的影响,含6 wt%HB-20的聚醚型PU与不含HB-20的PU相比拉伸强度提高了2倍多,达到37.9 MPa,断裂伸长率仍高达414%.     

Effect of surface charge on adsorption of bovine serum albumin 2. Interaction of protein molecules with an anionic monolayer,as studied by ellipsometry,radiotracer and surface tension measurements

The adsorption of bovine serum albumin (BSA) onto an anionic monolayer of sodium docosylsulfate (SDocS) spread at the air/water interface was studied by ellipsometry. The adsorption behavior of BSA was estimated from the observed changes in phase differences and in the ratio of reflection coefficients. The dynamic process of BSA adsorption was measured after the injection of BSA solution into the aqueous substrate of SDocS monolayer. The gentle stirring of the substrate solution for 10 min was found to be enough to make the solution homogeneous without damaging the monolayer. The adsorption characteristics of BSA onto a negatively charged surface was compared with that onto a positively charged surface previously reported.The amount of adsorption depended on time and showed a maximum with an initial rapid rise, followed by gradual decrease toward the ultimate equilibrium value. The amount and time of the maximum adsorption depended on the concentration of BSA added to the aqueous substrate.Separate radiotracer measurement, using³⁵S-labeled SDocS monolayer, which is insoluble by itself, revealed that SDocS is solubilized into the bulk solution when BSA is added to the aqueous substrate.     

Competitive adsorption of collagen and bovine serum albumin—effect of the surface wettability

The competitive adsorption of collagen and bovine serum albumin (BSA) on surfaces with varied wettability was investigated with imaging ellipsometry, and ellipsometry. Silane modified silicon surfaces were used as substrates. The results showed that surface wettability had an important effect on protein competitive adsorption. With the decrease of surface wettability, the adsorption of collagen from the mixture solution of collagen and BSA decreased, while the adsorption of BSA increased.     

刷状结构的阳离子性接枝微粒QPDMAEMA/SiO_2对牛血清白蛋白的吸附特性

以微米级硅胶微粒为基质,通过接枝聚合和大分子反应,制备了具有刷状结构的阳离子性接枝微粒,深入研究了其对牛血清白蛋白(BSA)的强吸附能力、吸附机理和吸附热力学.首先使含叔胺基团的单体甲基丙烯酸二甲基氨基乙酯(DMAEMA)在硅胶微粒表面发生接枝聚合,制得接枝微粒PDMAEMA/SiO2,然后以氯乙胺为试剂,使接枝大分子PDMAEMA链中的叔胺基团发生季铵化反应,获得了具有刷状结构的阳离子聚电解质的功能接枝微粒QPDMAEMA/SiO2.测定了微粒QPDMAEMA/SiO2的zeta电位,实施了对BSA的等温吸附实验,考察了介质pH值、离子强度及温度对吸附作用的影响,研究了吸附热力学.研究结果表明,功能接枝微粒QPDMAEMA/SiO2比接枝微粒PDMAEMA/SiO2具有更高的zeta电位,在静电相互作用驱动下,微粒QPDMAEMA/SiO2对BSA具有很强的吸附能力.吸附容量随介质pH值的增大呈现先增大后减小的变化趋势,当pH值等于BSA的等电点(pI=4.7)时,具有最高的吸附容量(高达112 mg?g-1).以等电点为界,离子强度对吸附容量会产生完全相反的影响作用:当介质pH值小于BSA的等电点时,电解质浓度增大,吸附容量增高;当介质pH值等于BSA的等电点时,吸附容量几乎不随电解质的浓度发生变化.吸附过程熵值减小而且放出热量,是一个焓驱动的吸附过程.