牙膏中三氯生的高效液相色谱法检测

利用甲醇超声提取牙膏样品中的三氯生,采用高效液相色谱法(紫外检测器)测定了其含量;探讨了最佳提取和色谱检测条件.结果表明,该方法对牙膏中三氯生的检出限为1.0μg/g,在三氯生浓度10.5～210mg/L范围内线性关系良好,相关系数R=0.999 98;样品加标回收率为99.81%～103.33%,相对标准偏差为0.03%.该方法具有简便、快速、准确、灵敏的优点,适用于牙膏中三氯生的测定.     

高效液相色谱法测定人耳酚甘油滴耳液中苯酚含量

采用高效液相色谱HPLC法测定人耳酚甘油滴耳液中苯酚含量。结果表明苯酚浓度在23.0~184 mg/L的浓度范围内,色谱峰面积与苯酚浓度呈良好的线性关系(r=0.999 7);苯酚对照品溶液连续进样6次,保留时间的相对标准偏差(RSD)为0.44%,峰面积相对标准偏差(RSD)为0.15%;用该方法分析6份独立包装的人耳酚甘油滴耳液中苯酚含量,含量检出值的RSD为3.1%;回收率试验的总回收率为93%,RSD为0.02%。本方法可以准确的测定苯酚含量,方法操作简便、快速、重现性好,适用于人耳酚甘油滴耳液中苯酚含量的测定。     

超高效液相色谱法同时测定牙膏中5种植物源活性成分

建立了同时测定牙膏中丹皮酚(Pae)、麝香草酚(Thy)、和厚朴酚(Hon)、厚朴酚(Mag)、甘草次酸(Gly)5种植物源活性成分的超高效液相色谱方法。牙膏样品以90%甲醇为溶剂超声提取,离心取上清液过滤后进行分析,采用Waters ACQUITY UPLCHSS C_(18)(2. 1 mm×100 mm,1. 8μm)为分离柱,乙腈-0. 1%甲酸(pH 2. 8)为流动相,梯度洗脱,流速为0. 3 mL/min,二极管阵列检测器(PDA)的检测波长为275、250nm,外标法定量。结果表明,5种植物源活性成分在2～100 mg/L质量浓度范围内呈良好的线性关系,相关系数(r)均大于0. 999;检出限为0. 2～1. 0 mg/kg,定量下限为0. 8～3. 5 mg/kg;在4个加标水平下的平均回收率为90. 5%～99. 4%,相对标准偏差(RSD)为0. 7%～5. 1%。该法分析快速、重复性好、准确性好、灵敏度高,已应用于实际牙膏样品的测定。     

石墨炉原子吸收光谱法测定饮料中镉的含量

以磷酸二氢铵＋硝酸镁的混合液为基体改进剂测定了饮料中的镉,方法的回收率97.9%～100.7%,检出限为0.26 mg/mL,且测定样品快速、简便.     

电感耦合等离子体原子发射光谱法测定不锈钢中元素

研究了ICP发射光谱仪测定不锈钢中钛等5种元素的方法,确定了样品的分解方法及元素测定谱线,并对各元素进行适当的背景校正,在标准溶液与样品溶液种基体匹配的情况下,用ICP-AES法测定,当样品溶液的含量为5 mg/mL时,回收率在94.7%～103.7%之间,其精密度优于10%.方法简便、快速、精密度好、灵敏度高.     

液相色谱-质谱/质谱法对多种食品基体中三聚氰胺的检测

采用超声、振荡、液液萃取、离心等方法提取14种复杂食品基体中的三聚氰胺,提取液经阳离子交换固相萃取柱净化后,采用液相色谱-质谱/质谱法测定多种食品基体中的三聚氰胺.涉及的食品基体包括豆类制品、饮料、糕点、含乳饼干、鲜蛋、蛋制品和调味品6类基体14种食品.方法的检出限为0.005 ～0.012 5 mg/kg,回收率为75% ～115%,RSD小于18%;定量下限为0.025 ～0.062 5 mg/kg,回收率为84% ～106%,RSD小于10%.中、高浓度添加回收率为82% ～110%,RSD小于12%.方法灵敏、准确、有效.     

微波辅助萃取-气相色谱-质谱法测定牙膏中二甘醇

提出了气相色谱-质谱法测定牙膏样品中二甘醇的方法。用微波萃取法以无水乙醇作萃取溶剂,在120℃萃取20min,使牙膏样品中二甘醇溶于乙醇中,所得萃取液经脱水后,用气相色谱-质谱法测定其含量。色谱分离选用HP-INNOWAX色谱柱,采用程序升温方式;质谱测定中采用电子轰击离子源及选择离子监测模式。在最佳萃取和测定条件下,方法的线性范围为0.01～50.0mg·mL-1,检出限(3s/b)为0.005mg·mL-1。用1.0mg·mL-1二甘醇标准溶液6份按方法测定,对方法的精密度作了试验,测得相对标准偏差(n=6)小于1.6%。在牙膏样品基体上加入标准溶液作回收试验,测得回收率为95.0%～103.0%。     

基于中性解吸-电喷雾萃取电离质谱直接检测蜂蜜中的四环素

基于中性解吸-电喷雾萃取电离质谱(ND-EESI-MS)建立了无需样品预处理即可直接检测蜂蜜中四环素的方法. 测定结果表明, 加标蜂蜜四环素样品在20~1000 ng/mL浓度范围内线性关系良好(R²>0.997), 检出限为1.08 ng/mL; 加标浓度为50, 500和1000 ng/mL蜂蜜样品的回收率分别为94.26%, 98.38%和103.00%, 精密度(RSD)分别为3.28%, 1.39%和1.12%. 应用此方法对8种市售蜂蜜进行检测, 发现2种蜂蜜中含有痕量的四环素, 其余蜂蜜均未检出, 而应用高效液相色法在这8种市售蜂蜜中均未检出四环素. 本方法无需经过复杂的样品预处理, 灵敏度高、 精密度好、 分析速度快且特异性强, 能够承受蜂蜜中复杂基体的影响, 是一种快速检测蜂蜜中四环素的方法.     

高效液相色谱法测定冷冻机油中BTPP含量

将正相高效液相色谱法用于冷冻油中抗磨剂(BTPP)含量测定研究,建立了抗磨剂(BTPP)含量的快速分离检测方法.使用氨基键合相分析柱,以二氯甲烷∶正庚烷(80∶20,V/V)二元混合溶剂为流动相,流速为1.0 mL/min,于262 nm波长处检测.最低检测限为0.026 1%,相关系数在0.999 9以上.BTPP加标回收率为100±3.0%(n=4),日内测定结果的相对标准偏差RSD小于2.0%(n=8),方法快速、准确、重现性好,不需要复杂的样品预处理,实用性强,对环境污染小.     

高效液相色谱法测定牙膏中的氨甲环酸

建立了丹磺酰氯柱前衍生/高效液相色谱测定牙膏中氨甲环酸(TA)的方法。牙膏经甲醇提取、氮吹至干,再用丹磺酰氯进行衍生。衍生物通过X-Bridge C18色谱柱(250 mm×4.6 mm×5μm)分离,以乙腈和0.1%甲酸水溶液为流动相梯度洗脱,在紫外波长250 nm条件下进行定量测定。系统考察了缓冲溶液p H值、衍生温度和衍生时间对氨甲环酸衍生效率的影响。结果表明,在优化实验条件下,氨甲环酸衍生物与基体杂质达到有效分离,在1~425 mg/L范围内线性关系良好,相关系数为0.999 5;在20,200,1 600 mg/kg 3个加标浓度下的回收率为98.7%~102%,相对标准偏差为0.85%~2.5%,方法检出限为2.0 mg/kg。该方法准确、可靠、灵敏度高,适用于各类牙膏中氨甲环酸的测定。     

氟化电热蒸发／电感耦合等离子体原子发射光谱中的基体效应研究

本文系统研究了氟化电热蒸发／电感耦合等离子体原子发射光谱（ＥＴＶ－ＩＣＰ－ＡＥＳ）测定难熔元素的基体效应。与常规气动雾化（ＰＮ）－ＩＣＰ－ＡＥＳ中的基体效应比较，氟化ＥＴＶ－ＩＣＰ－ＡＥＳ中的基体效应更小。对难熔基体元素，由于基体和待测元素与氟化剂之间的竞争反应，随着基体浓度的增加，待测元素谱线强度降低；对常见基体元素，由于热循环中基体与待测元素之间的选择挥发，对待测元素的蒸发和传输过程无明显影响     

Comparison of matrix effects in HPLC-MS/MS and UPLC-MS/MS analysis of nine basic pharmaceuticals in surface waters

When developing an LC-MS/MS-method matrix effects are a major issue. The effect of co-eluting compounds arising from the matrix can result in signal enhancement or suppression. During method development much attention should be paid to diminishing matrix effects as much as possible. The present work evaluates matrix effects from aqueous environmental samples in the simultaneous analysis of a group of 9 specific pharmaceuticals with HPLC-ESI/MS/MS and UPLC-ESI/MS/MS: flubendazole, propiconazole, pipamperone, cinnarizine, ketoconazole, miconazole, rabeprazole, itraconazole and domperidone. When HPLC-MS/MS is used, matrix effects are substantial and can not be compensated for with analogue internal standards. For different surface water samples different matrix effects are found. For accurate quantification the standard addition approach is necessary. Due to the better resolution and more narrow peaks in UPLC, analytes will co-elute less with interferences during ionisation, so matrix effects could be lower, or even eliminated. If matrix effects are eliminated with this technique, the standard addition method for quantification can be omitted and the overall method will be simplified. Results show that matrix effects are almost eliminated if internal standards (structural analogues) are used. Instead of the time-consuming and labour-intensive standard addition method, with UPLC the internal standardization can be used for quantification and the overall method is substantially simplified.     

A sample preparation method for recovering suppressed analyte ions in MALDI TOF MS

In matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry (MALDI TOF MS), analyte signals can be substantially suppressed by other compounds in the sample. In this technical note, we describe a modified thin‐layer sample preparation method that significantly reduces the analyte suppression effect (ASE). In our method, analytes are deposited on top of the surface of matrix preloaded on the MALDI plate. To prevent embedding of analyte into the matrix crystals, the sample solution were prepared without matrix and efforts were taken not to re‐dissolve the preloaded matrix. The results with model mixtures of peptides, synthetic polymers and lipids show that detection of analyte ions, which were completely suppressed using the conventional dried‐droplet method, could be effectively recovered by using our method. Our findings suggest that the incorporation of analytes in the matrix crystals has an important contributory effect on ASE. By reducing ASE, our method should be useful for the direct MALDI MS analysis of multicomponent mixtures. Copyright © 2015 John Wiley & Sons, Ltd.     

标准物质基体对马拉硫磷气相色谱响应的影响

对马拉硫磷在甲醇、丙酮、乙酸乙酯、二氯甲烷4种溶剂中的气相色谱峰单位浓度面积响应进行了研究,用t检验法判定响应差异性.研究结果证明,浓度相同但溶剂不同的马拉硫磷溶液,在其它实验条件均相同的情况下,气相色谱峰单位浓度面积响应有显著性差异;用前处理后待测样浓缩液的基体稀释对照样,可以减小或消除马拉硫磷标准物质基体与方法中要求的标准储备液基体的差异性所带来的对待测样检测结果的影响.     

Simple approach for evaluation of matrix effect in the mass spectrometry of synthetic cannabinoids

A simple approach for studying and identifying matrix effect is described. This method for the determination of matrix effect combines the advantages of two most popular traditional methods while eliminating their disadvantages. A postcolumn infusion system was used to observe the MS signal alterations of synthetic cannabinoids: UR-144, XLR-11 and STS-135. Protein precipitation, liquid–liquid extraction and solid phase extraction sample preparation methods were tested. The results of the experiments showed that the discussed method of matrix effect estimation can have practical application in the development of analytical methods. The comparison of the normalized matrix effect profiles can be done even for data obtained over time. Obtained results also indicated that matrix effect was highly dependent on sample preparation. Although similar structure, significant differences were observed for different synthetic cannabinoids.     

A novel method for making ultra-fine metal fibers and particles

A novel method based on plastic processing and equipment for preparing ultra-fine metal fibers and particles is reported. With this new method, metal fibers and particles can both be produced on the same equipment and the surfaces of the fibers and particles can be protected from oxidation by the polymers or solvents during the preparation process. Metal-alloy powders with lower melt point were filled into polymer by an extruder, followed by a die-drawing process at a temperature lower than the melt temperature of the metal alloy. Metal fibers or particles were obtained after the polymer matrix was washed away. Metal alloy fibers can be obtained when a polymer that strongly interacts with metal alloy, such as a special polyvinyl alcohol with a low alcoholysis degree, is used as the polymer matrix. Metal-alloy particles can be obtained when a polymer with weak interaction with metal alloy, such as polyethylene (PE), is used as the polymer matrix. Based on the principle of this new method, it is possible to produce finer or even nano-sized metal fibers and particles with higher melting points.     

ICP-AES测定汽车催化剂中Pt、Rd、Rh的干扰研究

对用ICP-AES法测定汽车尾气净化催化剂中的Pt、 Rd、 Rh存在的干扰问题进行了研究. 发现催化剂中的载体成分和助剂成分对Pt、 Rd、 Rh的几条灵敏线均有不同程度的干扰, 这些干扰基本分为基体干扰和光谱干扰. 对于光谱干扰可选用不同谱线来消除干扰, 而基体干扰可采用等效浓度差减法或基体匹配来扣除, 也可采用标准加入法来进行测定. 但这些方法均存在一定的局限性.     

Assessment of sample cleanup and matrix effects in the pesticide residue analysis of foods using postcolumn infusion in liquid chromatography-tandem mass spectrometry

Matrix effect profiles can be used to visualize the effect of the sample matrix to the data signals occurring in a chromatogram. In the present study these profiles were generated by postcolumn infusion of a standard pesticide mix with extracts of different food matrices prepared by the QuEChERS method. Complete raw extracts as well as individual clean-up steps were analyzed. This allowed for a detailed comparison of the interferences caused by the matrix effects from various food samples. It also gave an idea about the efficiency of matrix reduction processes. When analyzing the individual clean-up extracts of the QuEChERS method just a slight reduction of matrix effects could be observed from step to step. Matrices causing strong signal effects in the results of the raw extracts also have strong effects after the final clean-up step. Some of the components responsible for the matrix effects show an extremely high retention time. After the injection of extracts from rocket or different types of tea, significant ion suppressions occurred even after rinsing the analytical column for a long time. The experiments have shown that similar matrices can produce different matrix effect profiles. For example, for black teas and green teas significantly different matrix effect profiles were obtained, while the matrix effects of teas within one of these groups were exactly the same. Analogous results could be found for citrus fruits. In order to overcome interfering matrix effects, analytical systems equipped with different electrospray ion sources were tested. Furthermore, profiles of diluted food extracts were generated. Dilution led to a significant decrease in the matrix effects.     

Overcoming matrix effects using the dilution approach in multiresidue methods for fruits and vegetables

During recent years matrix effects in liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) have quickly become a major concern in food analysis. The phenomenon of ion suppression can lead to errors in the quantification of the analytes of interest, as well as can affect detection capability, precision, and accuracy of the method. Sample dilution is an easy and effective method to reduce interfering compounds, and so, to diminish matrix effects. In this work, matrix effects of 53 pesticides in three different matrices (orange, tomato and leek) were evaluated. Several dilutions of the matrix were tested in order to study the evolution of signal suppression. Dilution of the extracts led to a reduction of the signal suppression in most of the cases. A dilution factor of 15 demonstrated to be enough to eliminate most of the matrix effects, opening the possibility to perform quantification with solvent based standards in the majority of the cases. In those cases where signal suppression could not be reduced, a possible solution would be to use stable isotope-labelled internal standards for quantification of the problematic pesticides.     

Mathematical optimization in the determination of the dissociation constants of a tribasic organic acid by 13C NMR spectroscopy

The calculation of dissociation constants from the chemical shifts of (13)C NMR spectra leads to a complicated non-linear equation. Two different mathematical methods for solution of this equation have been chosen--an iterative step method and a matrix pseudo-inversion method. When the iteration method is used the initial guesses for the parameters, the initial value of the step size and the escalation of the iteration must be optimized. For comparison the matrix pseudo-inversion method was used because it gives a unique result. With the optimized step method the results were as accurate or even better than those obtained with the matrix method. Although it takes time to optimize the system, the step method is the more suitable method of solving the problem. The matrix inversion can be done only with a computer with 13 significant digits and exponent capacity larger than +/- 38.