Direct synthesis of well-ordered and unusually reactive MnSBA-15 mesoporous molecular sieves with high manganese content

The mesoporous MnSBA-15 materials with different n(Si)/n(Mn) ratios of 4, 8, 20, and 50 have been synthesized, for the first time, using manganese nitrate tetrahydrate and Pluronic 123 triblock polymer [(EO)20(PO)70(EO)20] by simply adjusting the molar ratio of water to hydrochloric acid (n(H2O)/n(HCl)) under direct hydrothermal conditions. For the effect of structural and textural properties with incorporation of manganese, the MnSBA-15 has been synthesized with different synthesis temperatures at the fixed molar ratios of n(Si)/n(Mn) = 4 and n(H2O)/n(HCl) = 295 in the synthesis gel. The hydrothermal and thermal stabilities of MnSBA-15 have also been investigated. The calcined MnSBA-15 materials prepared have been characterized by ICP-AES, XRD, N2 adsorption, ESR, FE-SEM, and TEM. The ICP-AES studies show a higher amount of manganese incorporation on the silica pore walls, as MnSBA-15 with a n(Si)/n(Mn) ratio up to 2.2 can be successfully prepared at a fixed n(H2O)/n(HCl) molar ratio of 295 by adjusting the ratios of n(Si)/n(Mn) in the synthesis gel. The structural and textural properties of calcined MnSBA-15 prepared can be found by the results of XRD and N2 adsorption. The investigation of ESR results clearly describe the effect of structure and Mn species coordination on the SBA-15 silica pore walls while the uniform pore diameter and rope-like hexagonal mesoporous structure of MnSBA-15 can be identified by TEM and FE-SEM images. With increasing synthesis temperature, an increase the unit cell parameter, pore size, and pore volume and a decrease the specific surface area and pore wall thickness of MnSBA-15 can be obviously noted by the results of XRD and N2 adsorption. The hexagonal MnSBA-15 materials prepared could be tested as catalysts in epoxidation of trans-stilbene to produce trans-stilbene oxide under various optimal conditions while their catalytic properties could also be compared to the results of MnMCM-41 and ZrMnMCM-41.     

Synthesis and characterization of SBA-3, SBA-15, and SBA-1 nanostructured catalytic materials

A highly ordered large pore mesoporous silica molecular sieve SBA-3, SBA-15, Al-SBA-15, and SBA-1, were developed and characterized by XRD, BET, FTIR, SEM, and NMR-MAS. The catalytic materials were synthesized using different raw materials and operation conditions. These materials contain a regular arrangement of uniform channels with diameters between 1.8 and 10 nm, high specific surface area and high specific pore volume. The designed methods were effective for the synthesis, presenting each mesostructured materials, patterns of XRD and other characteristics corresponding to the reported ones in literature. The new route employed to synthesize Al-SBA-15, generates a catalyst with only aluminum in tetrahedral form, according to the data of (27)Al NMR-MAS. However, several reports indicated that the coordination of the Al atoms changes below the Si/Al ratio of 45, presenting peaks corresponding to penta and hexa-coordinated aluminum, which are absent in our samples (Si/Al = 50 and 33).     

Al-MCM-41介孔分子筛催化对甲酚叔丁基化反应的研究

2-叔丁基对甲酚是一种有机中间体,在有机合成领域中占有重要地位,被广泛应用于表面活性剂、高档酚类抗氧化剂2246和2246-S、紫外线吸收剂UV-326等的生产[1]。特别是近十年来,以抗热老化为特征的功能性高档酚类抗氧化剂在国内外相继问世,它们对于提高聚合物材料的成型加工性能、     

WxC/SBA-16催化剂的制备、表征及催化加氢脱硫性能

以正硅酸乙酯为硅源, 仲钨酸铵为钨源, P123和F127为混合模板剂,采用水热晶化法一步合成了不同钨含量(以n(Si):n(W)表示)的WO3/SBA-16, 然后经甲烷/氢气(V(CH4)/V(H2)=1/4)混和气体程序升温还原碳化(TPC), 制备出了WxC/SBA-16(x=1, 2)催化剂. 采用XRD、N2-吸附/脱附、TEM和FTIR等分析测试技术对样品的结构进行了表征, 并以噻吩作为模型化合物, 对WxC/SBA-16催化剂的加氢脱硫催化活性进行了评价. 结果表明, 在一定钨含量的条件下, WO3/SBA-16和WxC/SBA-16样品仍然保持立方笼状介孔结构, 当n(Si):n(W)为30-10时, 碳化钨的物相为W2C; n(Si):n(W)为7.5时, 碳化钨的物相为W2C和WC. WxC/SBA-16催化剂表现出了良好的加氢脱硫催化性能.     

NMR provides checklist of generic properties for atomic-scale models of periodic mesoporous silicas

MCM-41 and SBA-15 silicas were studied by (29)Si solid-state NMR and (15)N NMR in the presence of (15)N-pyridine with the aim to formulate generic structural parameters that may be used as a checklist for atomic-scale structural models of this class of ordered mesoporous materials. High-quality MCM-41 silica constitutes quasi-ideal arrays of uniform-size pores with thin pore walls, while SBA-15 silica has thicker pore walls with framework and surface defects. The numbers of silanol (Q(3)) and silicate (Q(4)) groups were found to be in the ratio of about 1:3 for MCM-41 and about 1:4 for our SBA-15 materials. Combined with the earlier finding that the density of surface silanol groups is about three per nm(2) in MCM-41 (Shenderovich, et al. J. Phys. Chem. B 2003, 107, 11924) this allows us to discriminate between different atomic-scale models of these materials. Neither tridymite nor edingtonite meet both of these requirements. On the basis of the hexagonal pore shape model, the experimental Q(3):Q(4) ratio yields a wall thickness of about 0.95 nm for MCM-41 silica, corresponding to the width of ca. four silica tetrahedra. The arrangement of Q(3) groups at the silica surfaces was analyzed using postsynthesis surface functionalization. It was found that the number of covalent bonds to the surface formed by the functional reagents is affected by the surface morphology. It is concluded that for high-quality MCM-41 silicas the distance between neighboring surface silanol groups is greater than 0.5 nm. As a result, di- and tripodical reagents like (CH(3))(2)Si(OH)(2) and CH(3)Si(OH)(3) can form only one covalent bond to the surface. The residual hydroxyl groups of surface-bonded functional reagents either remain free or interact with other reagent molecules. Accordingly, the number of surface silanol groups at a given MCM-41 or SBA-15 silica may not decrease but increase after treatment with CH(3)Si(OH)(3) reagent. On the other hand, nearly all surface silanol groups could be functionalized when HN(Si(CH(3))(3))(2) was used.     

Preparation and application of nanocatalysts via surface functionalization of mesoporous materials

Surface immobilization of active species onto mesoporous materials is gaining importance, especially in the design of functionalized mesoporous materials as a nanocatalyst through heterogenization of homogeneous catalytic systems. This article summarizes recent work on the synthesis, characterization and catalytic performance of the functionalized mesoporous catalysts performed by the present authors. A cationic rhenium(I) complex was encapsulated into mesoporous Al-MCM-41 molecular sieve using a ion-exchange method, yielding a new photocatalyst to be active for photocatalytic reduction of CO₂. Surface functionalization of mesoporous silica SBA-15 with sulfonic acid groups was investigated to give a solid acid catalyst. The chemically modified Fe-containing mesoporous materials, which are active for hydroxylation of phenol, were prepared by a surface-grafting method that iron salts are immobilized onto mesoporous Si-MCM-41 with the help of 3-aminopropyltrimethoxysilane as a linker. A cobalt(III) complex was heterogenized onto mesoporous silica SBA-15 containing carboxylic groups in order to utilize as a solid catalyst for the liquid-phase oxidation of aromatic hydrocarbons.     

Characterization and acidic properties of Al-SBA-15 materials prepared by post-synthesis alumination of a low-cost ordered mesoporous silica

A series of Al-containing SBA-15 type materials with different Si/Al ratio, were prepared by post-synthesis modification of a pure highly ordered mesoporous silica SBA-15 obtained by using sodium silicate as silica source, and amphiphilic block copolymer as structure-directing agent. A high level of aluminum incorporation was achieved, reaching an Si/Al ratio of up to 5.5, without any significant loss in the textural properties of SBA-15. These materials were fully characterized by powder X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), ²⁷Al NMR spectroscopy, and N₂ adsorption at 77 K. The acid properties of these materials have been evaluated by NH₃-TPD, adsorption of pyridine and deuterated acetonitrile coupled to FTIR spectroscopy. The effective acidity of these materials was evaluated using two catalytic reactions: 2-propanol dehydrogenation and 1-butene isomerization. The adsorption of basic probe molecules and the catalytic behavior revealed an evolution of the acid properties with the Al content. These studies have shown that the Al-SBA-15 materials contain Brønsted and Lewis acid sites with medium acidity which makes them appropriate to be used as acid catalysts in heterogeneous catalysis, catalytic supports, and adsorbents.     

双酸体系下有序介孔SO42-/ZrO2-SiO2材料的合成

采用一锅合成法通过调变自组装过程中硫酸和盐酸的体积比,成功制备了系列介孔SO₄^2-/ZrO₂-SiO₂固体酸材料(Zr/Si物质的量为1.1).XRD、UV-Vis DRS、HR-TEM等表征结果表明,所得材料均具有高度有序的二维介孔结构及四方相氧化锆的晶体结构.氮吸附和FT-IR表征结果进一步发现,通过改变硫酸/盐酸体积比可有效调变材料比表面积、孔容、孔径及表面L酸与B酸的相对强度.与纯硅介孔分子筛SBA-15不同,此系列SO₄^2-/ZrO₂-SiO₂固体酸材料均在正戊烷的异构化反应中表现出较高的催化活性和稳定性.其原因在于,在合成过程中硫酸的加入不仅促使了酸基的形成,而且稳定了催化剂的晶体结构;盐酸的存在则保持了有序的介孔结构.由此可见,混酸合成体系有望制备出结构有序、酸性可调、催化性能优越的新型催化材料,并在众多酸催化反应中取得应用.     

Preparation of ordered mesoporous SiC from preceramic polymer templated by nanoporous silica

Highly ordered mesoporous SiC materials were prepared by infiltrating viscous liquid preceramic polymer, allylhydridopolycarbosilane, into two types of surface modified nanoporous silica templates: mesoporous silica SBA-15 and mesocellular siliceous foam. The silica templates were subsequently etched off after pyrolysis at 1000 degrees C under nitrogen atmosphere with the resultant formation of ordered mesoporous structures. The mesoporous SiC materials, synthesized from both types of templates possessed high Brunauer-Emmett-Teller (BET) surface areas in the range of 250-260 m(2)/g with pore sizes of 3.4-3.6 nm. The ordered structures of mesoporous SiC were exact inverse replicas of their respective silica templates, as characterized by small angle X-ray diffraction (XRD), transmission electron microscope (TEM) images, and the adsorption-desorption isotherm of nitrogen.     

Influence of the pore structure of MCM-41 and SBA-15 silica fibers on atomic layer chemical vapor deposition of cobalt carbonyl

Mesoporous high surface area MCM-41 and SBA-15 type silica materials with fibrous morphology were synthesized and used as support materials for the ALCVD (atomic layer chemical vapor deposition) preparation of Co/MCM-41 and Co/SBA-15 catalysts. Co/MCM-41 and Co/SBA-15 catalysts were prepared by deposition of Co2(CO)8 from the gas phase onto the surfaces of preheated support materials in a fluidized bed reactor. For both silica materials, two different kinds of preparation methods, direct deposition and a pulse deposition method, were used. Pure silica supports as well as supported cobalt catalysts were characterized by various spectroscopic (IR) and analytical (X-ray diffraction, Brunauer-Emmett-Teller, elemental analysis) methods. MCM-41 and SBA-15 fibers showed considerable ability to adsorb Co2(CO)8 from the gas phase. For MCM-41 and SBA-15 silicas, cobalt loadings of 13.7 and 12.1 wt % were obtained using the direct deposition method. The cobalt loadings increased to 23.0 and 20.7 wt % for MCM-41 and SBA-15 silicas, respectively, when the pulse deposition method was used. The reduction behavior of silica-supported cobalt catalysts was found to depend on the catalyst preparation method and on the mesoporous structure of the support material. Almost identical reduction properties of SBA-15-supported catalysts prepared by different deposition methods are explained by the structural properties of the mesoporous support and, in particular, by the chemical structure of the inner surfaces and walls of the mesopores. Pulse O2/H2 chemisorption experiments showed catalytically promising redox properties and surface stability of the prepared MCM-41- and SBA-15-supported cobalt catalysts.     

SBA-15 supported HPW: Effective catalytic performance in the alkylation of phenol

SBA-15 was synthesized using non-ionic surfactant as the structure directing agent at 40 °C. It was then impregnated with different loadings (10, 30, 50 and 70%) of phosphotungstic acid. They were characterized by XRD, N₂ adsorption, FT-IR and DRIFT techniques. The physicochemical characterization revealed that SBA-15 could accommodate discrete phosphotungstic acid due to its large pore volume and high surface area. The catalytic activity of these materials was examined in the vapour phase tert-butylation of phenol using tert-butyl alcohol as the alkylating agent. The influence of reaction parameters such as reaction temperature, reactant feed ratio, WHSV and time on stream was studied, and the results were correlated with physicochemical characteristics of the catalysts. 4-tert-Butyl phenol was observed as the major product with high selectivity. Among the catalysts, 30% phosphotungstic acid supported SBA-15 showed high phenol conversion under optimum conditions, which is significantly higher than either phosphotungstic acid loaded mesoporous AlPO or AlMCM-41.     

Ti-Si介孔分子筛的转晶与控制

以季铵盐型阳离子Gemini表面活性剂[C16H33(CH3)2N+(CH2)6N+(CH3)2C16H33]•2Br−(GEM16-6-16)为模板剂, 改变n(Ti)/n(Si)比值, 合成了系列Ti-Si介孔分子筛. X射线衍射(XRD)和透射电子显微镜(TEM)等表征结果表明, 在n(Ti)/n(Si)≤0.20时, 分子筛为高度有序六方介孔; 当 n(Ti)/n(Si)为 0.30时, 介孔转晶为立方相; 当n(Ti)/n(Si)为0.50时, 介孔转晶为层状相; n(Ti)/n(Si)为1.0时, 材料失去有序孔道结构. FT-IR分析表明, 在分子筛骨架间形成了Ti—O—Si键, 而且Ti—O—Si键的数目随n(Ti)/n(Si)的增加而增加, 达到一定饱和值后基本保持不变. 乙醇和丁醇对纯硅基介孔分子筛孔结构转晶控制作用呈现六方相→立方相→层状相递变规律, 因而钛酸正丁酯水解生成的丁醇对Ti-Si介孔分子筛转晶具有一定的控制作用.     

巯基功能化介孔材料高效锚定钯负载型催化剂的制备及其苯酚加氢催化性能

以含巯基官能团有机硅烷修饰的介孔材料MCM-41和SBA-15为载体, 采用浸渍-氢气还原法制备了高分散和高活性的负载型Pd催化剂. X射线衍射、N₂吸附-脱附和透射电子显微镜表征结果显示, 所制Pd催化剂Pd-SH-MCM-41和Pd-SH-SBA-15具有很好的长程有序结构、分布均匀的孔径、高比表面积及高度分散的Pd颗粒. 苯酚加氢反应结果表明, 以Pd-SH-MCM-41和Pd-SH-SBA-15为催化剂时, 在80℃, 1.0MPa反应1h, 苯酚转化率达99%以上, 环己酮选择性为98%. 它们的催化活性为商业Pd/C催化剂的5倍, Pd/MCM-41和Pd/SBA-15催化剂的3倍. 这可归因于介孔材料表面修饰的巯基官能团对Pd的锚定作用, 避免了Pd颗粒的团聚, 使其高度分散在介孔材料上.     

Synthesis and characterization of surface modified SBA-15 silica materials and their application in chromatography

Hexagonally ordered SBA-15 mesoporous silica spheres with large uniform pore diameters are obtained using the triblock copolymer, Pluronic P123, as template with a cosurfactant cetyltrimethylammonium bromide (CTAB) and the cosolvent ethanol in acidic media. A series of surface modified SBA-15 silica materials is prepared in the present work using mono- and trifunctional alkyl chains of various lengths which improves the hydrothermal and mechanical stability. Several techniques, such as element analysis, nitrogen sorption analysis, small angle X-ray diffraction, scanning electron microscopy (SEM), FTIR, solid-state (29)Si and (13)C NMR spectroscopy are employed to characterize the SBA-15 materials before and after surface modification with the organic components. Nitrogen sorption analysis is performed to calculate specific surface area, pore volume and pore size distribution. By surface modification with organic groups, the mesoporous SBA-15 silica spheres are potential materials for stationary phases in HPLC separation of small aromatic molecules and biomolecules. The HPLC performance of the present SBA-15 samples is therefore tested by means of a suitable test mixture.     

A Novel,Efficient and Facile Method for the Template Removal from Mesoporous Materials

A new catalytic-oxidation method was adopted to remove the templates from SBA-1 5 and MCM-4 1 me- soporous materials via Fenton-like techniques under microwave irradiation. The mesoporous silica materials were treated with different Fenton agents based on the template＇s property and textural property. The samples were cha- racterized by powder X-ray diffraction（XRD） measurement, N2 adsorption-desorption isotherms, infrared spectro- scopy, 29Si MAS NMR and thermo gravimetric analysis（TGA）. The results reveal that this is an efficient and facile approach to the thorough template-removal from mesoporous silica materials, as well as to offering products with more stable structures, higher BET surface areas, larger pore volumes and larger quantity of silanol groups.     

Effects of Morphology and Structural Characteristics of Ordered SBA-15 Mesoporous Silica on Release of Ibuprofen

Three kinds of highly ordered SBA-15 mesoporous materials with different pore sizes and morphologies denoted as LPS-SBA-15 (stick-like with pore size 7.28 nm), CPS-SBA-15 (stick-like with pore size 5.96 nm) and T-SBA-15 (tablet-like with pore size 4.64 nm) have been prepared, characterized and employed as carrier materials. The release behaviors of the ibuprofen in a simulated body fluid from these mesoporous silica materials were studied. The influences of pore size and exterior morphologies of mesoporous silica on the release behaviors of ibuprofen have been investigated. It has been found that the release becomes fast with increasing of pore size and slow with extending of transport pathway, and that the release rate of ibuprofen from the three kinds of SBA-15 is LPS-SBA-15 > T-SBA-15 > CPS-SBA-15. The results show that the inner structure as well as the exterior morphologies of SBA-15 mesoporous silica can seriously affect the release behaviors of ibuprofen.     

Hydrogen bonding of water confined in mesoporous silica MCM-41 and SBA-15 studied by 1H solid-state NMR

The adsorption of water in two mesoporous silica materials with cylindrical pores of uniform diameter, MCM-41 and SBA-15, was studied by 1H MAS (MAS=magic angle spinning) and static solid-state NMR spectroscopy. All observed hydrogen atoms are either surface -SiOH groups or hydrogen-bonded water molecules. Unlike MCM-41, some strongly bound water molecules exist at the inner surfaces of SBA-15 that are assigned to surface defects. At higher filling levels, a further difference between MCM-41 and SBA-15 is observed. Water molecules in MCM-41 exhibit a bimodal line distribution of chemical shifts, with one peak at the position of inner-bulk water, and the second peak at the position of water molecules in fast exchange with surface -SiOH groups. In SBA-15, a single line is observed that shifts continuously as the pore filling is increased. This result is attributed to a different pore-filling mechanism for the two silica materials. In MCM-41, due to its small pore diameter (3.3 nm), pore filling by pore condensation (axial-pore-filling mode) occurs at a low relative pressure, corresponding roughly to a single adsorbed monolayer. For SBA-15, owing to its larger pore diameter (8 nm), a gradual increase in the thickness of the adsorbed layer (radial-pore-filling mode) prevails until pore condensation takes place at a higher level of pore filling.     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6, 同时通过改变水热温度制备了不同孔径大小的SBA-15, 并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段, 对其介孔结构进行了表征. 以正丁醛为探针分子, 考察了其对有机醛的吸附, 并与Y-沸石的吸附性能做了对比. 结果表明, 材料的介孔比表面积与其对正丁醛的吸附量成正比, 吸附等温线符合Langmuir 模型, 属于单层吸附, 具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g^-1). 最后将SBA-15添加到卷烟滤嘴中, 实验结果表明, SBA-15能显著降低卷烟烟气中巴豆醛的释放量.     

有序介孔二氧化硅对正丁醛的吸附性能

合成了一系列具有不同孔结构与性质的有序介孔二氧化硅材料SBA-15、MCM-41、SBA-16、KIT-6,同时通过改变水热温度制备了不同孔径大小的SBA-15,并利用小角X射线散射、透射电镜、扫描电镜和氮气吸附-脱附等手段,对其介孔结构进行了表征.以正丁醛为探针分子,考察了其对有机醛的吸附,并与Y-沸石的吸附性能做了对比.结果表明,材料的介孔比表面积与其对正丁醛的吸附量成正比,吸附等温线符合Langmuir模型,属于单层吸附,具有最大介孔比表面积的MCM-41对正丁醛的吸附量最大(484 mg·g-1).最后将SBA-15添加到卷烟滤嘴中,实验结果表明,SBA-15能显著降低卷烟烟气中巴豆醛的释放量.     

混合超分子液晶模板法合成六方介孔相含钛氧化硅

采用混合十六烷基三甲基溴化铵（CTAB）与不同碳链的脂肪胺（CnNH2n＋3, n=8,10,12,14,16）作模板,在四甲基氢氧化胺为碱源的条件下,合成了具有六方介孔结构的含钛氧化硅Ti MCM 41分子筛材料. XRD和TEM测试表明所合成材料具有高度的长程有序结构,样品的N2吸附/脱附等温线表明,高度有序的Ti MCM 41材料展示了毛细凝聚的陡峭台阶和狭窄的介孔孔径分布.对反应物配比中Ti/Si比、脂肪胺碳链长度n对六方介孔相结构的影响进行了研究,实验发现当Ti/Si< 0.15和n< 16时,均可获得具有六方介孔结构的含钛氧化硅Ti MCM 41;而当Ti/Si≥0.15或n >16时,产物将分别发生从六方向无定形态或从六方向层状介孔相结构的转移,从混合表面活性剂的堆积参数对这种相转移现象进行了分析.