P3HT修饰一维有序壳核式CdS/ZnO纳米棒阵列复合膜的光电化学性能

采用电化学方法在铟锡氧化物(ITO)导电玻璃上制备了高度有序的ZnO纳米棒阵列, 在ZnO纳米棒阵列上先后电化学沉积CdS纳米晶膜及聚3-己基噻吩(P3HT)薄膜得到P3HT修饰的一维有序壳核式CdS/ZnO纳米阵列结构, 并通过扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、能量散射X射线(EDX)等表征手段证实了该结构的形成. 以此纳米结构薄膜为光阳极组装新型半导体敏化太阳电池, 研究了CdS纳米晶膜的厚度和P3HT薄膜的沉积对电池光伏性能的影响, 初步探讨了电荷在电池结构中的传输机理, 结果表明, CdS纳米晶膜和P3HT薄膜的沉积有效地拓宽了光阳极的光吸收范围, 实验中电池的光电转换效率最高达到1.08%.     

P3HT/CdS/TiO2/ZnO一维有序核壳式纳米棒阵列的构制及其在杂化太阳电池中的应用研究

采用恒电位法在铟锡氧化物导电玻璃(ITO)上制备了高度有序一维ZnO纳米棒阵列,将ZnO纳米棒阵列在TiO2溶胶中采用提拉法制备出了一维TiO2/ZnO核壳式纳米棒阵列.在一维TiO2/ZnO核壳式纳米棒阵列上电沉积CdS纳米晶得到一维CdS/TiO2/ZnO核壳式纳米棒阵列,然后在一维CdS/TiO2/ZnO核壳式纳米棒阵列上电沉积聚3-己基噻吩(P3HT)薄膜得到P3HT/CdS/TiO2/ZnO核壳式纳米结构薄膜.以该纳米结构薄膜电极为光阳极制备出新型纳米结构杂化太阳电池,研究了该类电池的光电转换性能,初步探讨了该类电池的工作机理.     

Sb2S3纳米粒子修饰ZnO纳米片微纳分级结构的光电化学性能

采用恒电位方法,选择氯化钾和乙二胺(EDA)为添加剂,在氧化铟锡(ITO)导电玻璃上制备了高度有序的ZnO纳米片阵列,通过二次电沉积得到了ZnO纳米片上生长纳米棒的微纳分级结构.利用化学浴沉积法在ZnO基底上沉积Sb₂S₃纳米粒子制备出了Sb₂S₃/ZnO纳米片壳核结构和Sb₂S₃/ZnO微纳分级壳核结构.利用扫描电子显微镜(SEM)、X射线衍射(XRD)、紫外-可见(UV-Vis)吸收光谱、瞬态光电流等对其形貌、结构组成和光电化学性能进行了表征和分析.结果表明, Sb₂S₃/ZnO纳米片上生长纳米棒分级壳核结构的光电流明显高于Sb₂S₃/ZnO纳米片壳核结构.在Sb₂S₃/ZnO纳米片壳核结构和Sb₂S₃/ZnO微纳分级壳核结构的基础上旋涂一层P3HT薄膜形成P3HT/Sb₂S₃/ZnO复合结构,以上述复合结构薄膜为光活性层组装成杂化太阳电池,其中, P3HT/Sb₂S₃/ZnO分级壳核结构杂化太阳电池的能量转换效率最高,达到了0.81%.     

ZnO纳米管有序阵列与Cu_2O纳米晶核壳结构的光电化学性能及全固态纳米结构太阳电池研究

采用电化学方法在铟锡氧化物(ITO)导电玻璃基底上制备了高度有序的ZnO纳米管阵列,然后在ZnO纳米管阵列上电化学沉积Cu2O纳米晶颗粒,获得了一维有序Cu2O/ZnO核壳式纳米阵列结构,通过控制Cu2O纳米晶的沉积电量得到不同厚度的Cu2O壳层,并对该核壳式纳米阵列的形貌和结构进行了分析.以Cu2O/ZnO一维核壳式纳米阵列结构为光电极组装全固态纳米结构太阳电池,研究了Cu2O壳层厚度对光电极光吸收性能、光电性能以及组装电池光伏性能的影响,优化了电池中对电极材料的喷金厚度.结果表明,以Cu2O沉积电量为1.5 C的Cu2O/ZnO为光活性层,以4 mA电流下真空镀金20~25 min的铜基底为对电极组装的简易太阳电池最高可获得0.013%的光电转换效率.     

ZnO纳米管有序阵列与Cu2O纳米晶核壳结构的光电化学性能及全固态纳米结构太阳电池研究简

采用电化学方法在铟锡氧化物(ITO)导电玻璃基底上制备了高度有序的ZnO纳米管阵列,然后在ZnO纳米管阵列上电化学沉积Cu2O纳米晶颗粒,获得了一维有序Cu2O/ZnO核壳式纳米阵列结构,通过控制Cu2O纳米晶的沉积电量得到不同厚度的Cu2O壳层,并对该核壳式纳米阵列的形貌和结构进行了分析. 以Cu2O/ZnO一维核壳式纳米阵列结构为光电极组装全固态纳米结构太阳电池,研究了Cu2O壳层厚度对光电极光吸收性能、光电性能以及组装电池光伏性能的影响,优化了电池中对电极材料的喷金厚度. 结果表明,以Cu2O沉积电量为1.5 C的Cu2O/ZnO为光活性层,以4 mA电流下真空镀金20~25 min的铜基底为对电极组装的简易太阳电池最高可获得0.013%的光电转换效率.     

二氧化钛纳米管阵列薄膜的超声辐射阳极氧化制备

通过使用铂片作为对电极在含有氢氟酸的二甲基亚砜溶液中, 将金属钛片进行阳极氧化的方法制备得到二氧化钛纳米管阵列薄膜. 在施加40 V偏压超声辐射作用下阳极氧化24 h条件下得到的二氧化钛纳米管长达到680 nm, 管内直径25 nm, 管壁厚度约3～5 nm. 采用了XRD和TEM等分析手段表征了二氧化钛纳米管阵列薄膜的微观结构和表面形貌, 分别测试了薄膜的光吸收性能、循环伏安特性和光化学转换效率, 并和碱性溶胶-凝胶方法制备的纳米晶二氧化钛薄膜作了对比研究. 实验制备的二氧化钛纳米管阵列薄膜电极的光吸收率比纳米晶二氧化钛薄膜提高了40%, 光电化学转换效率前者是后者的6倍, 实验结果表明二氧化钛纳米管阵列薄膜结构有利于加快电子的传输, 并能减少电荷复合, 采用这种二氧化钛纳米管阵列薄膜结构的染料敏化太阳能电池光电极有望进一步提高太阳能电池的效率. 本文还探讨了在超声波辐射作用下二氧化钛纳米管阵列薄膜的形成机理.     

Y2O3/TiO2 "核-壳"结构在染料敏化太阳电池中的应用

在纳米TiO₂多孔薄膜表面包覆超薄绝缘体,形成"核-壳"结构的势垒层,是目前染料敏化太阳电池（DSC）光阳极改性的研究热点之一.本文选取氧化钇（Y₂O₃）作为包覆层材料,采用浸渍法对纳米TiO₂多孔薄膜进行修饰,研究Y₂O₃包覆处理对TiO₂薄膜微观结构及能带结构的影响;将浸渍法制备得到的Y₂O₃/TiO₂"核-壳"结构光阳极应用于DSC中,研究了饣覆层对电子传输复合以及DSC光电转换性能的影响.结果表明,Y₂O₃包覆处理后,薄膜的平带电势负移,且电子复合得到有效抑制,电子寿命增大,电池的开路电压明显提高.研究表明,适量引入Y₂O₃可以达改善电池性能的目的.     

聚3-甲基噻吩及聚3-己基噻吩修饰钛酸盐纳米管的光电化学性能研究

采用水热法制备了钛酸盐纳米管, 并将钛酸盐纳米管制备成纳米结构电极进行光电化学研究. 钛酸盐纳米管产生阳极光电流, 具有n-型半导体特性. 结果表明, 聚3-甲基噻吩[poly(3-methylthiophene), PMeT]、聚3-己基噻吩[poly(3-hexylthiophene), P3HT]修饰钛酸盐纳米管后产生的光电流均较纯钛酸盐纳米管的光电流高, 且使产生光电流的波长向长波区移动. 钛酸盐纳米管/PMeT、钛酸盐纳米管/P3HT的光电转换效率分别达11.40%, 0.91%(未校正光子损失). 钛酸盐纳米管/PMeT的光电转换效率较钛酸盐纳米管/P3HT的光电转换效率高10.5%. 钛酸盐纳米管/PMeT、钛酸盐纳米管/P3HT中存在p-n异质结, 在一定条件下p-n异质结的存在有利于光生电子/空穴的分离.     

异质结界面修饰对TiO2/P3HT杂化太阳电池光电性能的增强作用

采用水热法在F-SnO₂(FTO)导电玻璃上制备了一维TiO₂纳米棒阵列, 将一种两亲有机三苯胺染料M分子吸附在其表面, 进而旋涂有机聚合物聚3-己基噻吩P3HT, 构建结构为FTO/TiO₂/M/P3HT/PEDOT:PSS/Au的杂化太阳电池. 瞬态光电流谱反映在杂化电极中存在pn异质结. 接触角测试表明TiO₂表面吸附有机M分子后, 亲水性表面转变为疏水性表面, 利于与聚合物P3HT的进一步接触; 稳态荧光发射光谱表明经修饰的杂化电极的荧光发射强度降低, 由荧光衰减曲线拟合得到的荧光寿命降低, 说明在TiO₂与P3HT之间存在有效的电荷转移, 电荷复合被抑制. 电化学阻抗分析表明界面修饰后电子复合电阻和电子寿命增大. 电池的特性参数均比界面修饰前有所提高, 光电转换效率为1.61%. 另外, 对该电池的工作机理、电荷传输过程进行了初步探讨.     

液相沉积法制备ZnO/CdS复合纳米棒阵列薄膜及其光电性质

采用两步化学溶液沉积法在氧化铟锡(ITO)导电玻璃衬底上制备了ZnO/CdS复合纳米棒阵列薄膜.利用X射线衍射(XRD)仪、扫描电子显微镜(SEM)、紫外-可见(UV-Vis)吸收分光光度计、荧光(PL)光谱仪及表面光电压谱(SPS)研究了不同CdS沉积时间对复合薄膜的晶体结构、形貌、光电性质的影响.研究结果表明:ZnO纳米棒阵列表面包覆CdS纳米颗粒后,其吸收光谱可拓展到可见光区;与吸收光谱相对应在可见光区出现新的光电压谱响应区,这一现象证实,通过与CdS复合可显著提高ZnO纳米棒阵列在可见光区的光电转换性能;随着CdS纳米颗粒沉积时间的延长,复合纳米棒阵列薄膜在大于383nm波长区域的光电压强度逐渐减弱,而在小于383nm波长区域的光电压强度逐渐增强.用两种不同的电荷产生和分离机制对这一截然相反的光响应过程进行了详细的讨论和解释.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.