双硫腙修饰玻碳电极阳极溶出伏安法测定痕量镉和铅

报道了双硫腙修饰玻碳电极同时测定痕量镉和铅的电分析方法。镉和铅离子通过与电极表面的双硫腙发生螯合作用而富集在电极表面 ,同时在 -1 .2 0V(vs.SCE)还原成零价镉和铅 ,当电极电势从 -1 .2 0V向 -0 .3 0V扫描时 ,被还原的镉和铅从电极表面溶出 ,分别于 -0 .78V和 -0 .4 8V左右形成灵敏的阳极溶出峰。优化了支持电解质及pH值、双硫腙用量、富集电位及时间等实验参数。利用该修饰电极测定镉、铅的线性范围分别为 1 .0×1 0 - 8～ 2 .5× 1 0 - 6 mol L和 5 .0× 1 0 - 9～ 2 .5× 1 0 - 6 mol L。检测限分别为 5 .0× 1 0 - 9mol L和7.0× 1 0 - 1 0 mol L。该法用于实际水样中镉和铅的测定 ,平均回收率分别为 99.3 0 %和 99.5 4 %。     

悬汞电极阳极溶出伏安法 Ⅲ.铍化合物中镉和铅的测定

用悬汞电极阳极溶出伏安法,以硫酸铍为支持电解质,测定硫酸铍及氧化铍中的镉与铅。硫酸铍适宜浓度为0.1—0.4M,PH1—3.5。测定镉与铅的灵敏度分别为4.4×10~(-8)M及2.5×10~(-8)M。相对偏差在±3.5％以内。     

毛细管电泳单脉冲伏安测定重金属铜铅锌镉

以毛细管为分离通道 ,在KNO3 缓冲溶液中 ,用表面镀汞膜的金微电极作为工作电极 ,采用单脉冲伏安法同时测定铜、锌、铅、镉含量 ,考察并优化了影响分离和检测的相关因素 :缓冲溶液pH、分离高压、脉冲上限和下限、脉冲宽度等。该法的最佳实验条件 :5mmol/LKNO3(pH6.0) ,分离高压20kV ,脉冲上限 -0.2V ,脉冲下限 -1.15V(vs.SCE) ,脉冲宽度500ms。结果表明 ,各峰面积与其离子浓度成线性关系 ,线性范围(μg/mL)分别为 :铜5.0×10-2～10.0;锌1.0×10-2～10.0 ;铅5.0×10-2～5.0 ;镉2.0×10-2～10.0。加标回收率在95%～110%之间。用该法较好地测定了水样中的重金属铜锌铅镉     

微波消解-石墨炉原子吸收法测定酵母粉中的微量铅和镉

本文采用微波消解-石墨炉原子吸收法直接测定酵母粉中微量铅和镉的含量。利用硝酸和过氧化氢消解样品,对微波消解的条件,基体改进剂的选择,铅原子化温度的效果以及常见元素对测定的干扰进行了研究。在优化的实验条件下,方法对铅和镉的检出限(3σ)分别为0.062 ng/mL和0.013 ng/mL,相对标准偏差(RSD)分别为0.64%~1.11%、0.75%~4.70%,加标回收率在95.00%~102.0%之间。本法已用于酵母粉中微量铅和镉的测定,分析结果与电感耦合等离子体-质谱(ICP-MS)法具有良好的一致性。     

二乙胺荒酸钠–四氯化碳萃取连续光源原子吸收法测定磷酸一二钙中的痕量铅、镉

建立连续光源原子吸收分光光度法同时测定磷酸一二钙(MDCP)中铅、镉的方法。MDCP经盐酸消解后,以氢氧化钠溶液调节p H为11,加入KCN作为掩蔽剂,用二乙氨荒酸钠–四氯化碳络合铅、镉离子,再经CCl_4进一步萃取浓缩,采用连续光源原子吸收分光光度法测定铅、镉的含量。该方法铅、镉的检出限为1,0.5 mg/kg;用于不同批次MDCP产品测定,铅、镉测定结果的相对标准偏差分别为3.58%,6.91%(n=11);铅、镉的加标回收率分别为88.9%~104.7%,91.0%~106.4%。该法可用于MDCP中痕量铅、镉的同时测定。     

溶出伏安法同时测定水中痕量铀和镍

本文报道了同时测定钴和镍的一种方法.在 0.01mol/L NH_3·H_2O-0.01mol/LNH_4Cl-3.0×10~(-5)mol/L安息香缩氨基硫脲(BTSC)溶液中,钴(Ⅱ)和镍(Ⅱ)均产生非常灵敏的还原波,其峰电位分别是:-0.94和-0.75V(vs.SCE),峰电流与钴和镍的浓度分别在2.0×10~(-8)~1.0×10~(-6)和1.0×10~(-8)~8.0×10~(-7)mol/L范围内成直线关系,该方法用于测定水中痕量钴和镍,相对标准偏差分别为1.4~2.0%和2.1~2.5%,回收率分别在98.0%~101.8%和97.9%~102.1%之间.     

微分电位溶出法连续测定饮料中的铜铅镉锌

建立了微分电位溶出法连续测定饮料中痕量铜、铅、镉、锌的新方法。在HAc- Na Ac( p H4 .5)～ 3.5× 1 0 -2 mol·L-1KCl～ 2 .6× 1 0 -5 mol· L-1Hg2 +介质中测定锌 ,然后调节底液为 0 .0 1 mol·L-1HCl,连续测定铜、铅、镉。铜、铅、镉、锌 ,检出限分别为 4 ,0 .1 ,2 ,4 μg· L-1,线性测定范围 Zn2 +:0～ 30 0 μg·L-1,Cu2 +、Pb2 +、Cd2 +:0～ 2 2 0μg· L-1,回收率为 83.4 %～ 1 0 3.3% ,RSD<3.4 % ( n=7)。该法较好解决了金属互化物的影响 ,样品不需消化便可直接测定。     

氢化物发生-原子吸收光谱测定钢铁中痕量铅

对氢化物发生-原子吸收光谱(HG-AAS)测定铅的预氧化问题和铅的氢化物发生的新机理作了理论上的探讨。发现铅氢化物发生最佳条件同酸、碱等物质的量浓度的中和相关。对柠檬酸的络合、缓冲作用作了研究。发现K3Fe(CN)6的光敏作用能消除钢中有关化学元素对测量铅的干扰。提出了简便准确的钢中0.000 0x%铅的直接测定方法。应用此法分析了5个标样中的铅含量,结果与标准值一致,得RSD为2.0%(n=4,wPb6.2×10-5%)及1.5%(n=14,wPb1.3×10-3%),方法的测定限为w(Pb)5×10-6%。     

电感耦合等离子体发射光谱(ICP-OES)法测定铅精矿中9种元素

采用硝酸-盐酸-氢氟酸-高氯酸溶样,优化仪器测定条件及消除干扰元素的条件实验等,建立了电感耦合等离子体发射光谱(ICP-OES)法测定铅精矿中砷、锑、铋、铜、锌、镁、铝、铁、镉的方法。其测定范围ω(As):0.02%~1.50%;ω(Sb):0.01%~10.00%;ω(Bi):0.03%~5.00%;ω(Cu):0.50%~10.00%;ω(Zn):2.00%~10.00%;ω(Mg):0.30%~2.00%;ω(Al):0.50%~3.00%;ω(Fe):5.00%~12.00%;ω(Cd):0.030%~0.20%。经加标回收实验,各元素的加标回收率为90%~104%(n=3)。方法准确、快速、可靠,适用于铅精矿中砷、锑、铋、铜、锌、镁、铝、铁、镉量的同时测定。     

真空蒸馏-塞曼效应石墨炉原子吸收法测定高纯镉和碲中铁铝镍铬铜银锰

采用真空蒸馏与塞曼效应石墨炉原子吸收仪相结合进行高纯镉和高纯碲中铁、铝、镍、铬、铜、银、锰等元素的测定。方法简便、快速,测定下限分别为Fe3×10~(-8)%,Al8×10~(-8)%,Ni5×10~(-8)%,Cr7×10~(-8)%,Cu4×10~(-8)%,Ag 2.5×10~(-9)%,Mn2.5×10~(-9)%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.