非晶铁基合金中两类不同的压磁效应

 本文详细介绍了在0.000 1~2.3 GPa流体静压力下测量三种非晶合金饱和磁感应强度B_s和最大磁导率μ_max的实验方法。实验结果表明：三种非晶合金受压后B_s和μ_max表现各异，可归为两大类。（1）第一类压磁效应：总趋势是B_s和μ_max都随压力增加而下降，但在几个压力区B_s反常增高。如Fe₇₅Ni₅Si₅B₁₅非晶合金B_s随压力增加均匀下降，(Fe_0.85Co_0.15)Cu_0.4Si_4.4B_13.2非晶合金的B_s随压力增加降—升—再降。（2）第二类压磁效应，如Fe_78.75Cu_1.25Si₅B₁₅非晶合金的B_s和μ_max随压力增加都有未见报导过的微弱升高。分别结合局域电子模型的交换作用理论和巡游电子模型的刚带理论进行了讨论。     

流体静高压原位磁测量的误差研究（二）──退磁场的影响

 为了探讨流体静高压原位磁测量中退磁场的影响有多大？分别选用6种不同片数（n＝1、3、5、7、10、13）的非晶Fe_46.3Co_0.03Ni_46.5Si_3.75V_0.92B_2.5合金薄带样品，先后放进13层密绕直螺线管初级线圈内，采用工业频率400 Hz去测量和比较其磁化曲线、磁导率曲线和起始磁化曲线。研究表明：（1）样品片数越多，退磁场的影响越大，导致μ_m和μ_i出现惊人的测量误差，以1片（μ_m＝4 430，μ_i＝3 396）为最准。（2）随着样品片数的增多，测量饱和磁感应强度B_s＝0.837～0.762T，表明受退磁场影响较小。（3）若要减小退磁场误差，可将样品做得更薄，如0.2 μm薄膜。（4）若要彻底消除退磁场误差，必须采用闭合磁路，如用非晶合金薄带卷成的圆环。     

流体静高压原位磁测量的误差研究（三）——综合兼顾两种影响

 先后选用1至3片非晶Fe_46.3Co_0.03Ni_46.5Si_3.75V_0.92B_2.5合金薄带作样品,插入13层密绕直螺线管内,分别在高静水压容器内和其他四种不同环境中测量它们的磁化曲线、磁导率曲线和起始磁化曲线,再次研究了初级线圈采用多层直螺线管对铁镍合金样品的误差。（１）实验结果表明：既存在样品材料被磁化而形成的退磁场H',也存在漏磁通引起周围铁器磁化而形成的退磁场H'。（２）为了缩小H'的影响,只用1片非晶合金薄带作样品时,H'的影响变得严重,导致μ_m和μ_i出现惊人的误差：Δμ_m/μ_m=50%,Δμ_i/μ_i＝104%。（３）为了综合兼顾这两种影响,采用3片非晶合金薄带作样品时,虽然H'的影响增大一点,但是H'的影响被更多地削弱,所以环境磁化引起的误差反而减小：Δμ_m/μ_m=29%,Δμ_i/μ_i＝15.5%。     

Cr对Fe-Zr基非晶合金电阻率及压力效应的影响

 在0.000 1~2.5 GPa范围不同静水压下，用四探针法详细测量了七种非晶态Fe_90-xCr_xZr₁₀合金（x=2、4、7、10、13、16、20）的电阻率。结果表明：（1）常压室温电阻率ρ₀与FeZr基非晶合金中Cr含量成N形曲线关系；（2）当静水压增加时，七种非晶合金的约化电阻率（ρ/ρ₀）都单调下降，x越大则电阻率下降的幅度越小；（3）非晶Fe_90-xCr_xZr₁₀合金电阻率的压力系数对x的变化相当敏感；（4）为方便查值，给出了六种典型静水压下ρ/ρ₀与x的曲线关系。最后，讨论了四种物理模型的选用以及相干交换散射在高压下的行为。     

因瓦合金纳米微粉的恒磁导率及其压力、频率特性和压力相变

 以Fe-30wt%Ni合金片为母合金，用蒸发冷凝法制备了三种粗细不同的纳米微粒。经透射电镜和X光衍射物相分析，微粒成分与母合金一致。5T、5H和3K粉的平均粒度分别为13.6、27和40 mm。在室温和43~28个不同的流体静压力（0.000 1~2.205 GPa）下测量了它们的磁化曲线、磁导率曲线和起始磁化曲线。结果表明：（1）在H＝(20－132)(1000/4π)A/m范围内Fe-30Ni合金三种纳米粉均具有恒磁导率。（2）三种纳米粉恒磁导率随静水压的变化规律如下：μ_r＝3.83+0.253p-0.022 1p²-0.007 22p³（5T粉）；μ_r＝3.93+1.20p-1.97p²+1.52p³-0.510p⁴+0.059 9p⁵（5H粉）；μ_r＝5.96-0.276p+0.107p²-0.045 9p³（3K粉）。前两者随压力增加而升高。后者随压力增加而下降。（3）γ-α马氏体相变明显存在于5T、5H粉中，而3K粉中未见到。（4）Fe-30Ni合金片的μ_i从200kHz至2 MHz已下降一个数量级，而其纳米粉μ_i的频率范围高于300 MHz，增大两个数量级以上。     

坡莫合金纳米粉的恒导磁性及其磁导率的压力、频率特性

 用蒸发冷凝法制备了Fe-50wt%Ni和Fe-84wt%Ni坡莫合金的纳米微粉。经透射电镜X光能谱微区成分分析证实：微粉的成分与原材料的一致；微粉的平均粒径分别为16 nm（Fe-50Ni）和19 nm（Fe-84Ni）。在室温和36个不同的流体静压力（0.000 1~2.205 GPa）下原位测量了它们的磁化和起始磁化曲线。结果表明：（1）Fe-50wt%Ni和Fe-84wt%Ni合金纳米微粉均具有恒导滋特性；（2）这两种纳米粉的起始磁导率随静水压的变化分别为μ_i=8.16+18.2p-24.7p²+18.1p³-6.55p⁴+0.908p⁵（Fe-50Ni合金）和μ_i=5.38-0.169p+0.232p²-0.0786p³（Fe-84Ni合金）；（3）纳米粉的起始磁导率μ_i在频率高于10 MHz才降低，而Fe-50Ni合金片的μ_i在频率高于1 MHz，Fe-84Ni高于100 kHz时就开始下降，故纳米压粉磁芯可应用的频率范围可以比相应组分合金片的大1~2个数量级。     

Fe40Ni40P12B8非晶合金的冲击晶化实验研究

 本文研究了Fe₄₀Ni₄₀P₁₂B₈非晶合金冲击波加载下的晶化行为，冲击波由二级轻气炮发射的告诉弹丸撞击靶产生。实验结果表明：Fe₄₀Ni₄₀P₁₂B₈非晶合金在冲击波加载下，晶化可在加载时间（微秒量级）内发生；晶化的阈值压力在30~50 GPa之间，相应的冲击温度约为510~800 K，晶化析出相与冲击压力有关，低压下析出相是面心立方γ-(Fe, Ni)固溶体和Fe₃(P_0.37B_0.63)化合物，高压下（大于60 GPa）析出相除了面心立方γ-(Fe, Ni)固溶体和Fe₃(P_0.37B_0.63)化合物之外，还包括(Fe, Ni)₃P化合物。     

纳米晶FeCuNbMSiB（M＝Nb，V，Mo）合金的微结构及其电阻率与压力的关系

 X射线衍射和透射电镜的结果表明：非晶FeCuNbMSiB（M＝Nb，V，Mo）合金在540 ℃退火20 min，表面析出的纳米晶是α-FeSi固溶体，粒度为10~20 nm。此外，在0.000 1~2.4 GPa范围内测量了它们的常压室温电阻率以及电阻率随静水压的变化，得到了电阻率与压力的线性关系式。最后探讨了热处理方式和温度对非晶Fe_73.1Cu_1.2Nb_3.2Si_12.5B₁₀合金退火形成纳米晶的影响。     

与Al发生扩散反应的非晶(Fe0.99Mo0.01)78Si9B13晶化

 高压下与Al发生扩散反应的非晶(Fe_0.99Mo_0.01)₇₈Si₉B₁₃（FMSB）的晶化产物与纯FMSB的不同。与Al反应的FMSB非晶在3.0~5.0 GPa、780~900 K热处理时,晶化为α-Fe(Al)和次亚稳非晶合金;在这一压力范围以外,720~900 K热处理时,晶化为α-Fe(Si)、Fe₃B或Fe₂B。与Al发生反应的FMSB非晶可能通过与Al的扩散反应在Al/FMSB界面开始晶化。压力和温度对晶化过程的影响主要是由于α-Fe固溶体的Gibbs自由能随压力、温度和Al含量的变化。     

静高压下非晶(Fe0.99,Mo0.01)78Si9B13合金晶化过程的热力学研究

 在600~930 K，常压到7 GPa的范围内，对非晶(Fe_0.99,Mo_0.01)₇₈Si₉B₁₃合金等温等压退火30 min。实验表明：其晶化产物α-Fe(Mo, Si)、Fe₃B和Fe₂B相的析出与所加压力密切相关。压力使非晶(Fe_0.99,Mo_0.01)₇₈Si₉B₁₃合金的晶化温度和亚稳Fe₃B相的析出温度下降，在一定的压力和温度下，亚稳Fe₃B相将向稳定Fe₂B相转变，其转变温度随压力而变化。还对非晶(Fe_0.99,Mo_0.01)₇₈Si₉B₁₃合金的晶化和亚稳Fe₃B到稳定Fe₂B转变的热力学机制进行了讨论，并给出Fe₃B向Fe₂B的相转变方程。     

非晶态(Fe1-xCox)77.5Nd4B18.5合金的电阻率的压力系数和压力弛豫研究

在０．０００１－２．４ＧＰａ流体静压力范围详细研究了非晶(Fe_1-xCo_x)_77.5Nd₄B_18.5（０≤ｘ≤１．０）合金的电阻率与压力的关系，得到该非晶合金电阻率的压力系数随组分ｘ变化的规律。结果表明：用少量的钴（ｘ＝０．２）替代铁，不会影响其硬磁性和热稳定性，同时却可减小电阻率的压力系数，从而增强电磁性能在压力下的稳定性。此外还观测到在０．５１ＧＰａ保压３－２４h的结构弛豫，进一步求出该非晶台金电阻率的压力弛豫时间对组分ｘ的依赖关系。 关键词：     

Development of soft magnetic amorphous alloys with distinctly high Fe content

This paper reports on the preparation of Fe_(82.7-85.7)Si_(2-4.9)B_(9.2-11.2)P_(1.5-2.7)C_(0.8) soft magnetic amorphous alloys with a distinctly high Fe content of 93.5-95.5 wt.% by component design and composition adjustment. All alloys can be readily fabricated into completely amorphous ribbon samples with good surface quality by the single copper roller melt-spinning method. These alloys show good bending ductility and excellent magnetic properties after annealing, i.e., low coercivity(H_c) of 3.3-5.9 A/m, high permeability(μ_e)of 5000-10000 and high flux saturation density(B_s) of 1.63-1.66 T. The mechanism of the good glass forming ability(GFA) and soft-magnetic properties are explored. The amorphous alloys with the high Fe content comparable to that of the desired high Si alloy can be promising candidates for the potential application in electric devices.     

钆钴非晶合金薄膜的电子衍射研究

用电子衍射方法研究了一些非晶钆钴合金磁性薄膜的结构,用Lorentz电子显微技术观察了其相应的磁结构。在所有薄膜的电子衍射图上均可清楚地看见七个弥散衍射环,其中两个最小的环分布在s<0.6?^-1(s=2sinθ/λ)的范围内。在不同的薄膜中观察到磁泡或平面畴结构。本文就这种由两种原子半径相差较大的元素,如稀土和过渡元素构成的非晶合金,讨论了如何只根据s<0.6?^-1范围内的衍射强度峰形,直接、定性地了解稀土与稀土原子、稀土与过渡族原子以及过渡族与过渡族原子之间最近邻配位数相对大小的问题。也讨论了钆钴薄膜相分离对磁各向异性的影响。 关键词：     

Optimisation of soft magnetic properties in Fe–Cu–X–Si13B9 (X=Cr,Mo, Zr) amorphous alloys

In the present paper a group of Fe–Cu–X–Si₁₃B₉ (X=Cr, Mo, Zr) amorphous alloys has been examined by applying different experimental techniques—magnetic permeability, magnetic after-effect, coercive force and electrical resistivity measurements. It has been shown that their soft magnetic properties can be optimised by 1-h thermal annealing at the temperature close to the crystallisation temperature. This leads to an increase of permeability and a decrease of coercive force, thermal instability (magnetic after-effect intensity) and electrical resistivity of the material. The optimisation effect is discussed in terms of different processes—(i) a formation of a nanocrystalline phase with the grain size much smaller than the ferromagnetic exchange length, (ii) an annealing out of microvoids formed during the fabrication process and also (iii) a decrease of the effective magnetostriction constant. The temperature of optimisation annealing treatment is always higher than the Curie temperatures of the materials and varies approximately linearly with the atomic radius of the alloying additions.     

Metallic magnetism in amorphous TM-Y (TM = Mn,Fe, Co,Ni) alloys

Systematic variations of magnetic properties in amorphous TM-Y (TM = Mn, Fe, Co, Ni) alloys are investigated on the basis of a finite temperature theory of amorphous metallic magnetism which takes into account both thermal spin fluctuations and the fluctuations due to structural and configurations disorder. It is shown that the magnetic phase diagrams calculated in the most random atomic configuration explain qualitatively the spinglass (SG) in Mn-Y, the SG ferromagnetism (F) transition in Fe-Y, and the F-paramagnetism transition in Co-Y and Ni-Y alloys. Magnetization vs concentration curves and susceptibility vs concentration curves as well as the effective Bohr magneton numbers are also shown to be explained qualitatively or semi-quantitatively by the theory. Their miscroscopic mechanisms are elucidated by means of their electronic structures, magnetic couplings, and atomic short range order. It is found that the magnetism in Fe-Y and Mn-Y amorphous alloys is strongly influenced by the atomic short range order. The result explains different magnetic phase diagrams in amorphous Fe-Y alloys and experimental SG transition temperatures in amorphous Mn-Y alloys.     

FeCo基纳米晶合金高温交换耦合作用机理

研究了500和600℃真空退火后的纳米晶Fe_38.4Co₄₀Si₉B₉Nb_2.6Cu合金初始磁导率随温度的变化规律,发现较高温度(600℃)退火的FeCo基纳米晶合金,在非晶相居里温度以上较宽温度范围内磁导率没有明显的衰减,这是在双相纳米晶合金中观察到的一种新现象,其磁特性不同于Fe基纳米晶合金.为了探明这种现象的起源,估算了与剩余非晶相同成分的非晶合金的居里温度及纳米晶粒间发生交换耦合作用的参数 关键词： 交换耦合作用 非晶相居里温度 交换耦合穿透深度     

Induced magnetic anisotropy in Co-doped Finemet-type nanocrystalline materials

Transverse magnetic anisotropy has been induced in the Fe_14.7Co_58.8Cu₁Nb₃Si_13.5B₉ and Fe_13.8Co₆₅Cu_0.6Nb_2.6Si₉B₉ amorphous ribbons by annealing under an external magnetic field. This anisotropy plays a predominant role, compared to magneto-crystalline and magneto-elastic anisotropies, in forming the magnetic properties and shaping the hysteresis loop. The effect of temperature and time of annealing on the induced magnetic anisotropy and magnetic properties (magnetic permeability, coercivity and power losses) in both alloys was investigated. Under this work, measurements of frequency dependence of the real and imaginary parts of magnetic permeability were made within a frequency range up to 110 MHz. It was found that as a result of magnetic field annealing the Snoek limit increases in both alloys compared to the Co-free Finemet.