混合模式毛细管聚合物整体柱的制备及应用

混合模式毛细管整体色谱柱由于保留机理多样,具有很好的应用前景。本文以[2-（甲基丙烯酰基氧基）乙基]二甲基-（3-磺酸丙基）氢氧化铵（SPE）为单体,乙二醇二甲基丙烯酸酯（EDMA）为交联剂,偶氮二异丁腈（AIBN）为引发剂,正丙醇/1,4-丁二醇/水三元体系为致孔剂,制备了聚合物基质SPE-co-EDMA毛细管液相色谱整体柱。通过系统优化致孔剂和反应物种类和配比、引发剂的用量、反应时间和反应温度等因素,提高了整体柱的柱效、机械强度、渗透性和重复性。结果表明该毛细管整体柱在10 MPa内具有良好的机械强度,渗透性为2.17×10^-14 m²,而且批次内和批次间峰面积的重现性（RSD）分别为1.0%和4.6%。以极性和非极性的多种化合物评价了该毛细管整体柱的色谱性能,结果表明该柱在高有机相中具有亲水相互作用机理,在低有机相中具有反相作用机理,显示出混合模式分离特性。     

反相高效液相色谱法测定呋喃西林中有关物质

建立反相高效液相法测定呋喃西林含量和有关物质的方法。采用Phenomenex Synergi Max-RP C12色谱柱（250 mm×4.6 mm,4μm）为分离柱，以乙腈-水（30∶70）为流动相，流量为1.0 mL/min，检测波长为375 nm，色谱柱温度为30℃。在该色谱条件下，呋喃西林色谱峰与相邻杂质峰的分离度大于1.5，呋喃西林的质量浓度在1.04～104.0μg/mL范围内与色谱峰面积线性关系良好（r=0.999 2），检出限为0.3μg/mL。样品中单一杂质测定值的相对标准偏差为6.5%(n=6)，杂质总和测定值的相对标准偏差为4.6%(n=6)，平均加标回收率为100.4%～101.3%。该方法操作简单，专属性强，准确性好，可有助于控制呋喃西林的质量。     

气相色谱法测定乙二醇精馏液中1,2-丁二醇和一缩二乙二醇含量

采用气相色谱法对乙二醇蒸馏液中微量杂质1,2-丁二醇(DB)和一缩二乙二醇(DEG)进行跟踪分析。色谱柱为DB-624石英毛细管柱(30m×0.25mm×1.4μm),分离在二阶程序升温条件下进行,分流比为80∶1,检测器为氢火焰离子化检测器(FID),外标法定量。峰面积与其浓度线性关系良好,DB和DEG的平均回收率分别为99.31%和99.51%,相对标准偏差分别为2.85%及2.68%。本方法简便、准确、重现性好。     

液相色谱-串联质谱法测定吉非替尼中4种基因毒性杂质

建立了一种同时测定吉非替尼中4种基因毒性杂质3-氯-4-氟苯胺、3,4-二氟苯胺、3-氟-4-氯苯胺和3,4-二氯苯胺的高效液相色谱-串联质谱（HPLC-MS/MS）方法。用Inertsil ODS-3柱（100 mm×3.0 mm,3μm）为色谱柱,以0.1%（体积分数,下同）甲酸水溶液-0.1%甲酸乙腈溶液为流动相,在电喷雾正离子模式下进行测定。该方法在特异性、线性、精密度、准确性、稳定性和耐用性方面得到了验证。4种基因毒性杂质在0.6~96.0μg/L范围内与峰面积呈良好线性关系。检测限和定量限分别为0.2~2.0μg/L和0.6~6.0μg/L。所有杂质的回收率为91.0%~98.5%。检测后,在批号16052301和R16052501-1样品中仅检测到3-氯-4-氟苯胺,但低于杂质限度（6 mg/L）。该方法简便可靠,可用于吉非替尼中4种基因毒性杂质的测定,并为质量控制提供参考。     

高效液相色谱-离子阱-飞行时间质谱法鉴定碱性嫩黄中的杂质及高效液相色谱法制备碱性嫩黄标准物质

该文建立了一种高效液相色谱-离子阱-飞行时间质谱（HPLC-IT-TOF-MS）分析非法食品添加剂碱性嫩黄样品中杂质成分的方法。对碱性嫩黄样品中的杂质进行多级质谱分析,根据各碎片离子的精确质量数推测出该杂质的具体组成,确定这个杂质为4-（亚氨基（4-（甲基氨基）苯基）甲基）-N,N-二甲基苯胺盐酸盐,从而推断出碱性嫩黄的合成方法及杂质的可能来源。同时建立了制备碱性嫩黄标准物质的方法,分别选用了粒径为10μm和5μm的制备液相色谱柱进行两次制备高效液相色谱分离纯化,进样量分别为1 mL和500μL,最终采用分析型高效液相色谱峰面积归一化法得到纯度为99.52%的碱性嫩黄标准物质。扣除0.34%水分含量,0.13%灰分含量,采用质量平衡法确定制备的物质最终纯度为99.05%,并通过UV、IR、LC-MS和NMR四大谱图进行化学结构的确认。该方法简单、高效,可拓展应用于其他非法食品添加剂标准物质的制备。     

高效液相色谱法测定精对苯二甲酸中微量杂质

建立了高效液相色谱法（HPLC）同时测定精对-苯二甲酸（PTA）中微量杂质4-羧基苯甲醛（4-CBA）、对-甲基苯甲酸（P-TOL）和苯甲酸（C7H6O2）含量的方法。采用的色谱柱为Shim-PackWAX-1柱，流动相为0.1mol/L NH3H2PO4 6%CH3OH，(pH4.5)，检测波长为254nm。PTA中微量杂质4-CBA、P-TOL和C7H6O2的含量分别为0.59-235.20mg/kg、4.52-392.00mg/kg和0.28-24.55mg/kg时线性关系良好，其线性相关系数分别为0.9998、0.9997和0.9999。苯甲酸加样平均回收率99.03％，RSD0.37％。     

离子排斥色谱-脉冲安培法测定电镀液中的游离CN-

建立了离子排斥色谱-脉冲安培法测定游离CN-的检测方法。方法使用IonPac ICE-AS1离子排斥柱为分析柱,以120 mmol/L HClO4为淋洗液,安培法检测（工作电极为Pt电极）。CN-的检出限为0.42μg/L（50μL进样,三倍基线噪音）;在1-1000μg/L范围内具有良好的线性（r=0.9996）。0.01 mg/L和0.1mg/LCN-分别连续进样9次,峰面积相对标准偏差（RSD）分别为4.0%和3.0%。用该方法检出了电镀液样品中大量的游离CN^-。对实际样品进行加标,其回收率在83%-117%之间。     

超高效液相色谱-串联质谱法测定注射用头孢曲松钠中2-巯基苯并噻唑的含量

建立了一种超高效液相色谱-串联质谱法（UPLC-MS/MS）测定注射用头孢曲松钠中2-巯基苯并噻唑（MBT）基因毒性杂质含量。样品经甲醇提取,50%(V/V)乙腈稀释后,采用ACQUITY UPLC HSS T3色谱柱（2.1 mm×100 mm, 1.8μm）分离,乙腈-0.05%(V/V)乙酸（80∶20, V/V）为流动相,电喷雾离子源（ESI）,多反应监测（MRM）负离子模式扫描,外标法定量。MBT在0.11～10.92 ng/mL范围内线性关系良好（r2=0.9989）,检出限为0.03 ng/mL,定量限为0.08 ng/mL,平均回收率为96.8%,相对标准偏差（RSD）不大于3.5%。采用该方法检测抽检的14个厂家63批次样品中MBT杂质含量,59批次样品中有MBT检出。该方法适用于注射用头孢曲松钠中MBT的定性和定量分析。     

基于整体柱的固相萃取-高效液相色谱法测定尿液中4种羟基多环芳烃

建立了基于聚合物整体柱的固相萃取-高效液相色谱测定尿液中4种羟基多环芳烃（OH-PAHs）的分析方法。在注射器管中合成聚（甲基丙烯酸丁酯-乙二醇二甲基丙烯酸酯）整体柱（poly （BMA-co-EDMA））,并将其用于尿液中4种羟基多环芳烃的前处理,同时考察了上样浓度、淋洗液、洗脱液和洗脱体积对萃取效率的影响。结合高效液相色谱-荧光分析,4种羟基多环芳烃在各自的范围内线性关系良好（r≥0.9991）;方法的检出限和定量限分别为0.06~0.09 ng/mL和0.20~0.30 ng/mL;日内（n=5）和日间（n=3）精密度分别为1.4%~5.3%和2.6%~7.3%。对焦炉工人尿液样品进行加标（3 ng/mL）回收试验,回收率为78.2%~117.0%。该固相萃取柱能够有效萃取和净化尿液中4种羟基多环芳烃,并且可以重复使用。该法简单、准确,可应用于尿液中羟基多环芳烃的分析。     

辛基二茂铁同分异构体标准物质的制备

以辛基二茂铁为原材料,利用常压色谱柱结合环糊精包结分离制得(2-辛基)-二茂铁、(3-辛基)-二茂铁、(4-辛基)-二茂铁3种相对纯度均大于99.5%的辛基二茂铁同分异构体,作为标准物质候选物。利用气相色谱法检测,考察标准物质候选物的均匀性和稳定性,用气相色谱–质谱法、核磁共振法分析候选物中杂质的结构,确定其类型。用内标法和主成分自身对照法对不同的杂质进行定值,并对定值不确定度进行评定。(2-辛基)-二茂铁、(3-辛基)-二茂铁、(4-辛基)-二茂铁的纯度分别为99.5%,99.5%,99.8%,扩展不确定度均为0.2%(k=2)。该标准物质可为相关物质的检测提供量值溯源标准。     

1,2-丁二醇共聚对聚对苯二甲酸乙二醇酯结晶行为及力学性能的影响

为了探索生物基乙二醇中的1,2-丁二醇(1,2-BDO)作为共聚单体对生物基聚对苯二甲酸乙二醇酯(PET)的结晶行为和力学性能的影响。 本文合成了生物基PET均聚物和不同1,2-BDO共聚单元摩尔分数的系列生物基PET共聚物(共聚单体摩尔分数分别为2.0%、2.7%和5.6%),并采用傅里叶变换红外光谱仪(FTIR)、差示扫描量热仪(DSC)和力学测试等技术手段研究了其结晶行为和力学性能。 结果表明,随着1,2-BDO共聚单元摩尔分数的增加,PET共聚物的熔融温度、结晶速率及结晶度均明显降低,表明1,2-BDO共聚单体的引入破坏了PET分子链的规整性,阻碍了PET链段的结晶。 PET材料的拉伸强度随着1,2-BDO共聚单元摩尔分数的增加而降低,而弯曲强度和弯曲模量略有升高。     

聚酯的序列结构对聚氨酯弹性体形貌的影响

以己二酸(AA),1,4-丁二醇(BDO),乙二醇(EG)分别采用一步法、二步法合成分子量为3000的聚酯PAEB-R和聚酯PAEB-A.再分别与二苯基甲烷二异氰酸酯(MDI)、扩链剂1,4-丁二醇(BDO),乙二醇(EG)反应分别合成固含量30%与粘度为20000的聚氨酯(PAEB-R)-MDI-TPU和聚氨酯(PAEB-A)-MDI-TPU.SEM、AFM表明不同工艺所合成的聚氨酯均存在微相分离,且聚氨酯(PAEB-R)-MDI-TPU微相分离程度高于(PAEB-A)-MDI-TPU.     

碱催化促进Ni-W/β分子筛催化剂氢解纤维素产1,2-丙二醇的研究

为提高纤维素催化氢解产醇类产物中1,2-丙二醇(1,2-PG)的收率,采用等体积浸渍法制备了以β分子筛为载体负载Ni和W的催化剂。结果表明,当7Ni-20W/β分子筛作为催化剂时,在240℃反应温度和6.0 MPa H_2的条件下反应30 min后,纤维素实现完全转化,1,2-PG和乙二醇(EG)产率分别达到19.3%和45.3%;不同于其他载体催化剂,β分子筛可以明显提高1,2-PG选择性。当不同碱催化剂加入到Ni-W/β分子筛催化剂反应体系后,可以进一步提高1,2-PG的选择性。尤其是当加入Ba(OH)_2后,1,2-丙二醇产率从19.3%提高了32.5%。为了探究碱催化剂在反应中的作用,以葡萄糖为底物进行了一系列的碱催化反应。结果表明,碱催化剂主要作用是有助于将葡萄糖异构化为果糖,从而促进纤维素转化为1,2-PG。催化剂在两次回收重复利用之后1,2-PG的收率只下降3.9%,乙二醇产率收率下降4.1%。     

Mobility of molecules of liquid diols in the temperature range of 303–318 K

The self-diffusion coefficients of diols (ethylene glycol (EG), 1,2- and 1,3-propanediols (PD), and 1,4-butanediol (BD)) are measured using the spin echo approach on protons in the temperature range of 303–318 K. The activation energies of self-diffusion are calculated and compared to the activation energies for viscous flow and dipole relaxation in these systems. A conclusion is reached as to the correlation of rotational and translational movements in liquid diols, due to the presence of a spatial network of hydrogen bonds in these solvents.     

催化选择转化多羟基化合物制备高附加值化学品研究进展

对近年来催化转化多羟基化合物制备5-羟甲基糠醛、乙二醇、1,2-丙二醇、1,3-丙二醇等高附加值化学品进行了综述. 分析了果糖、葡萄糖、纤维素等不同结构的碳水化合物制5-羟甲基糠醛存在的挑战, 并对相应的解决方法进行了总结. 对于5-羟甲基糠醛的转化, 我们重点讨论了5-羟甲基糠醛选择性氧化制备2,5-二甲酰基呋喃和2,5-呋喃二甲酸以及它们作为聚合单体的潜在应用. 概述了催化氢解纤维素、糖醇、甘油等多羟基化合物制备乙二醇、1,2-丙二醇、1,3-丙二醇等二元醇的方法, 并对可能的机理进行了讨论. 依据近年来多羟基化合物催化选择性转化制备高附加值化学品的研究现状, 对今后的研究热点进行了展望.     

Simultaneous determination of glycols based on fluorescence anisotropy

Simultaneous determination of non-fluorescent glycols in mixtures without separation or chemical transformation steps is described. Two methods based in the measure of fluorescence anisotropy of a probe such as fluorescein dissolved in the analyte or analyte mixtures are described. In the first method, the anisotropy spectra of pure and mixtures of analytes are used to quantitative determination (if the fluorophor concentration is in a range where fluorescence intensity is proportional to concentration). In the second method, a calibration curve anisotropy-concentration based on the application of the Perrin equation is established. The methods presented here are capable of directly resolving binary mixtures of non-fluorescent glycols on the basis of differences on the fluorescence anisotropy of a fluorescence tracer. Best analytical performances were obtained by application of the method based on Perrin equation. This method is simple, rapid and allows the determination of mixtures of glycols with reasonable accuracy and precision. Detection limits are limited by the quantum yield and anisotropy values of the tracer in the solvents. Recovery values are related to the differences in anisotropy values of the tracer in the pure solvents. Mixtures of glycerine/ethylene glycol (GL/EG), ethylene glycol/1,2-propane diol (EG/1,2-PPD) and polyethylene glycol 400/1,2-propane diol (PEG 400/1,2-PPD) were analysed and recovery values are within 95-120% in the Perrin method. Relative standard deviation are in the range 1.3-2.9% and detection limits in the range 3.9-8.9%.     

Improvement in the detection of impurities affecting ethylene glycol UV transmittance by gas chromatography-mass spectrometry

A method was developed for the detection of trace impurities affecting ethylene glycol UV transmittance, using gas chromatography-mass spectrometry in the selective ion monitoring mode. Four 1,2-cyclopentanediones were identified in commercial ethylene glycol as well as in several ethylene glycol plant streams, including 3-methyl-1,2-cyclopentanedione, 3,5-dimethyl-1,2-cyclopentanedione, 3,4-dimethyl-1,2-cyclopentanedione and 3-ethyl-1,2-cyclopentanedione. Quantification of the first three compounds was achieved by monitoring the molecular ion. This method requires no sample preparation and can detect the compounds of interest as low as 0.1 microg ml(-1). As a simple and rapid method, it can be used in tracing these 1,2-cyclopentanediones in glycol plants.     

A library of thermoresponsive PEG-based methacrylate homopolymers: How do the molar mass and number of ethylene glycol groups affect the cloud point?

In this study, a novel library of thermoresponsive homopolymers based on poly (ethylene glycol) (EG) (m)ethyl ether methacrylate monomers is presented. Twenty-seven EG based homopolymers were synthesized and three parameters, the molar mass (MM), the number of the ethylene glycol groups in the monomer, and the chemistry of the functional side group were varied to investigate how these affect their thermoresponsive behavior. The targeted MMs of these polymers are varied from 2560, 5000, 8200 to 12,000 g mol⁻¹. Seven PEG-based monomers were investigated: ethylene glycol methyl ether methacrylate (MEGMA), ethylene glycol ethyl ether methacrylate (EEGMA), di(ethylene glycol) methyl ether methacrylate (DEGMA), tri(ethylene glycol) methyl ether methacrylate (TEGMA), tri(ethylene glycol) ethyl ether methacrylate (TEGEMA), penta(ethylene glycol) methyl ether methacrylate (PEGMA), nona(ethylene glycol) methyl ether methacrylate (NEGMA). Homopolymers of 2-(dimethylamino) ethyl methacrylate (DMAEMA) were also synthesized for comparison. The cloud points of these homopolymers were tested in different solvents and it was observed that it decreases as the number of EG group was decreased or the MM increased. Interestingly, the end functional group (methoxy or ethoxy) of the side group has an effect as well and is even more dominant than the number of EG groups.     

纳米半导体光催化甲醇水溶液制乙二醇

采用主客体结构的纳米ＺｎＳ通过光催化法从甲醇水溶液选择性地合成了乙二醇（ＥＧ）．考察了杂质成分和体系的稳定性，研究了光源、催化剂的温度处理、反应时间、溶液ｐＨ和主体分子等因素对ＥＧ选择性的影响．     

Organocatalytic depolymerization of poly(ethylene terephthalate)

We describe the organocatalytic depolymerization of poly(ethylene terephthalate) (PET), using a commercially available guanidine catalyst, 1,5,7‐triazabicyclo[4.4.0]dec‐5‐ene (TBD). Postconsumer PET beverage bottles were used and processed with 1.0 mol % (0.7 wt %) of TBD and excess amount of ethylene glycol (EG) at 190 °C for 3.5 hours under atmospheric pressure to give bis(2‐hydroxyethyl) terephthalate (BHET) in 78% isolated yield. The catalyst efficiency was comparable to other metal acetate/alkoxide catalysts that are commonly used for depolymerization of PET. The BHET content in the glycolysis product was subject to the reagent loading. This catalyst influenced the rate of the depolymerization as well as the effective process temperature. We also demonstrated the recycling of the catalyst and the excess EG for more than 5 cycles. Computational and experimental studies showed that both TBD and EG activate PET through hydrogen bond formation/activation to facilitate this reaction. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011