用于高效去除水中孔雀石绿的三层结构磁性复合材料Fe3O4@聚丙烯酸@ZiF-8的制备

设计并合成了一种以磁性纳米粒子为核，聚合物为中间层，金属有机骨架材料为外层的三层结构磁性复合材料(Fe₃O₄@PAA@ZIF 8)。首先利用溶剂热法制备Fe₃O₄纳米粒子，然后通过蒸馏沉淀聚合法在Fe₃O₄纳米粒子表面包覆聚丙烯酸(PAA)层，最后通过原位沉积法在PAA外部包覆ZIF 8。在对Fe₃O₄@PAA@ZIF 8的组成和结构进行表征的基础上，深入研究其对孔雀石绿(MG)的吸附性能。透射电子显微镜(TEM)显示 Fe₃O₄@PAA@ZIF 8 具有明显的三层结构，Fe₃O₄的平均粒径为 117nm，PAA 层厚度约为 17 nm，ZIF 8层的厚度约为 14 nm。Fe₃O₄@PAA@ZIF 8对 MG 的吸附量随着 pH 的升高而增大，吸附过程符合准二阶动力学模型和 Langmuir等温吸附模型。此外，Fe₃O₄@PAA@ZIF 8还表现出良好的重复利用性能，8次循环利用后对MG(500 mg·L^-1)的最大吸附量仍可达982 mg·g^-1。     

不同形貌Fe3O4纳米粒子的氧化沉淀法制备与表征

用一种方法成功合成出了球体、四方体、八面体、不规则多面体、三角形和不规则颗粒等六种具有不同形貌的Fe₃O₄纳米粒子，通过扫描电子显微镜(SEM)表征了粒子形貌。试样经过X-射线衍射(XRD)表征具有尖晶石结构，且结晶良好。经震动样品磁强计(VSM)测定，各种形貌的Fe₃O₄纳米粒子都具有良好的磁性，其中八面体形貌的Fe₃O₄纳米粒子的饱和磁化强度达到86.56 emu·g^-1，剩磁为10.64 emu·g^-1，矫顽力为138 Oe。讨论了不同形貌的Fe₃O₄纳米粒子的形成机制，得出了晶核的生长环境对纳米粒子的形貌有重要影响的结论。     

Fe3O4@SiO2@mTiO2介孔多功能纳米复合颗粒的制备及载药能力

以溶剂热法制备氨基功能化的Fe₃O₄纳米颗粒为磁核,结合溶胶-凝胶法和模板法在其表面先后包覆上致密的SiO₂层和介孔TiO₂层,制备了磁性-发光-微波热转换性-介孔结构为一体的多功能核-壳结构纳米复合颗粒,并对其结构、性能及载药能力进行了研究。XRD分析表明:Fe₃O₄表面包覆上了无定形结构的SiO₂和TiO₂。TEM照片表明:所得的纳米复合颗粒具有明显的核壳结构和完美的球形,构成核的Fe₃O₄颗粒的尺寸在40~50 nm之间,Fe₃O₄@SiO₂@mTiO₂核壳结构纳米复合颗粒的尺寸为60~70 nm,壳层厚度约10 nm,并可观察到壳层中清晰的孔状结构。磁性、荧光光谱和微波热转换特性分析表明:该复合颗粒同时具有良好的发光性、磁性和微波热转换特性。N₂气吸附及药物负载率分析表明,该复合颗粒具有较高的比表面积(640 m²·g^-1)和介孔结构(孔径约2.8 nm)并且具有较高的药物负载率。     

Fe3O4磁性纳米粒子的超声包金及其表征

超声条件下, 在乙醇分散的3-氨丙基三乙氧基硅烷(APTES)功能化的磁性Fe₃O₄纳米粒子和四氯合金酸的混合溶液中滴加柠檬酸钠, 成功地制备了磁性Fe₃O₄/Au复合纳米粒子. 采用X射线粉末衍射仪(XRD)、紫外吸收可见光谱(UV-Vis)、带有电子能谱仪(EDS)的扫描电子显微镜(SEM)、透射电子显微镜(TEM)、光电子能谱(XPS)、超导量子干涉仪(SQUID)等方法, 对复合粒子的形态、结构、组成以及磁学性质进行了表征. 结果表明: 在此条件下制得的复合粒子粒径在30 nm左右, 室温下磁化强度可达63 emu/g.     

ATP适体接枝Fe3O4纳米粒子的制备及化学发光酶检测应用

制备了油酸修饰的Fe₃O₄纳米粒子,利用盐酸多巴胺对其表面进行氨基化改性,制得水分散性良好的Fe₃O₄纳米粒子,用X射线衍射、透射电镜、傅里叶变换红外光谱仪、振动样品磁强计和紫外-可见吸收光谱进行表征。随后,将氨基修饰的三磷酸腺苷（ATP）适体接枝到Fe₃O₄纳米粒子上,结合荧光素酶化学发光法进行ATP的定量检测,并应用于市售酸奶中乳酸菌ATP含量的检测,其灵敏度高、重现性好。各项实验结果表明所制备的Fe₃O₄纳米粒子是一种分散性好、易分离的载体,其粒径均一、稳定、磁性强、与适体结合性能好,拓展了Fe₃O₄纳米粒子在分析检测领域的应用。     

CuTAPc-Fe3O4纳米复合粒子及其漆酶固定化研究

漆酶的固定化研究对基于漆酶催化的光纤生物传感器具有十分重要的意义. 制备了四氨基酞菁铜(CuTAPc)-Fe₃O₄纳米复合粒子, 并用红外(IR)、场发射扫描电镜(FEG-SEM)、X射线衍射(XRD)、能谱、粒径仪等对其进行了表征. 结果表明形成了以CuTAPc包覆在Fe₃O₄纳米粒子表面的纳米复合粒子, 粒子呈现不规则球形, 且分布均匀, 粒子平均粒径在50 nm左右. 用此纳米复合粒子通过戊二醛交联法固定了漆酶, 固定后的酶比游离酶具有更好的贮存稳定性及操作稳定性. 这为研制高性能的光纤生物传感器打下了较好的基础.     

柠檬酸根对纳米Fe3O4颗粒的生长及性能的影响

现代诊断学的发展使得超小超顺磁性的Fe₃O₄粒子在医学领域具有重要应用价值。实验中利用某些羧酸盐对铁氧化物晶粒成长的抑制作用，在共沉淀法中引入柠檬酸根，制备出平均粒径小于5 nm的Fe₃O₄纳米分散体系。研究了不同柠檬酸根浓度对生成粒子的大小、结晶和表面吸附情况的影响。对Fe₃O₄颗粒在不同条件下的磁性与胶体稳定性进行了讨论。     

纳米Fe3O4-TiO2靶向光动力疗法对肝癌细胞的杀伤效应

光动力疗法(PDT)作为一种迅速发展的传统替代疗法,在抗癌治疗中显示出巨大的潜力.为增强靶向性和提高光催化杀伤效率,本研究设计了一种新型光敏剂Fe₃O₄-TiO₂磁性纳米粒.在不同外磁场下,考察其在可见光和紫外光激发下对肝癌细胞的杀伤效应.同时利用流式细胞术检测纳米Fe₃O₄-TiO₂对肝癌细胞凋亡率、细胞周期和线粒体膜电位的影响.根据纳米Fe₃O₄-TiO₂和肝癌细胞的作用方式探讨其抗癌机制.结果表明,可见光激发纳米Fe₃O₄-TiO₂可以杀伤癌细胞,且其杀伤效率与紫外光激发下无明显差别.此外,Fe₃O₄-TiO₂比TiO₂具有更高的细胞摄取率,从而使其具有更高的选择性和光催化杀伤效率.其作用机制是光催化纳米Fe₃O₄-TiO₂产生活性氧ROS抑制癌细胞,然后通过阻滞细胞周期G₀/G₁期,降低线粒体膜电位,线粒体去极化,最终诱导细胞凋亡.     

棒状CuFe4Ox的可控合成及其异戊醇脱氢反应的催化性能

利用液相沉淀法可控合成了均匀的棒状CuFe₄O_x催化剂。通过原位X射线粉末衍射（XRD）、高分辨透射电子显微镜（TEM）及程序升温还原（TPR）等手段表征其晶相结构、形貌和还原性能。通过还原棒状CuFe₄O_x获得Cu⁰/Fe₃O₄ 纳米棒,原位X射线光电子能谱（XPS）用于确定Cu⁰/Fe₃O₄ 表面的相组成。通过液相沉淀法制备棒状CuFe₄O_x,在120℃保持3 h后加入Na₂CO₃溶液至pH等于9时所得棒状形貌最为规整。以异戊醇脱氢反应作为探针反应,比较了Cu⁰/Fe₃O₄ 纳米棒和Cu⁰/Fe₃O₄ 纳米颗粒的催化反应性能,发现Cu⁰/Fe₃O₄ 纳米棒比Cu⁰/Fe₃O₄ 纳米粒子具有更好的活性和稳定性,表明棒状Fe₃O₄ 担载的Cu纳米粒子具有更好的结构稳定性。     

棒状CuFe4Ox的可控合成及其异戊醇脱氢反应的催化性能

利用液相沉淀法可控合成了均匀的棒状CuFe₄O_x催化剂。通过原位X射线粉末衍射（XRD）、高分辨透射电子显微镜（TEM）及程序升温还原（TPR）等手段表征其晶相结构、形貌和还原性能。通过还原棒状CuFe₄O_x获得Cu⁰/Fe₃O₄纳米棒,原位X射线光电子能谱（XPS）用于确定Cu⁰/Fe₃O₄表面的相组成。通过液相沉淀法制备棒状CuFe₄O_x,在120℃保持3 h后加入Na₂CO₃溶液至pH等于9时所得棒状形貌最为规整。以异戊醇脱氢反应作为探针反应,比较了Cu⁰/Fe₃O₄纳米棒和Cu⁰/Fe₃O₄纳米颗粒的催化反应性能,发现Cu⁰/Fe₃O₄纳米棒比Cu⁰/Fe₃O₄纳米粒子具有更好的活性和稳定性,表明棒状Fe₃O₄担载的Cu纳米粒子具有更好的结构稳定性。     

Synthesis of Fe3O4@SiO2@polymer nanoparticles for controlled drug release

Novel multifunctional nanoparticles containing a magnetic Fe₃O₄@SiO₂ sphere and a biocompatible block copolymer poly(ethylene glycol)-b-poly(aspartate) (PEG-b-PAsp) were prepared. The silica coated on the superparamagnetic core was able to achieve a magnetic dispersivity, as well as to protect Fe₃O₄ against oxidation and acid corrosion. The PAsp block was grafted to the surface of Fe₃O₄@SiO₂ nanoparticles by amido bonds, and the PEG block formed the outermost shell. The anticancer agent doxorubicin (DOX) was loaded into the hybrid nanoparticles via an electrostatic interaction between DOX and PAsp. The release rate of DOX could be adjusted by the pH value.     

Picolinimidoamide-Cu(II) complex anchored on Fe3O4@SiO2 core–shell magnetic nanoparticles: an efficient reusable catalyst for click reaction

A Cu(II) complex supported on Fe₃O₄@SiO₂ core–shell magnetic nanoparticles (MNPs) was prepared and characterized by FT-IR, XRD, SEM, EDX, TEM, VSM, TGA, and AAS analysis. The load of Cu on picolinimidoamide ligand anchored on Fe₃O₄@SiO₂ core–shell MNPs was determined as 1.22, 1.54, and 1.70 wt% using AAS, EDX and TGA analyses, respectively. Synthesized Cu(II) complex on Fe₃O₄@SiO₂ MNPs efficiently catalyzed a click reaction between alkyl halides, alkynes, and sodium azide to synthesize corresponding triazoles in high to excellent yields. The catalyst was recovered using an external magnetic field, and recycled for subsequent reactions without substantial loss of efficiency.     

可回收Fe3O4@SiO2-Ag磁性纳米微球对染料污染物的快速脱色处理

介绍了一种采用无毒廉价的前驱物制备Fe₃O₄@SiO₂-Ag磁性纳米微球的快捷方法,制备的Fe₃O₄@SiO₂-Ag纳米微球在NaBH₄存在下可以催化还原染料污染物.实验结果表明,Fe₃O₄@SiO₂-Ag磁性纳米粒子保持了Ag纳米粒子和Fe₃O₄纳米粒子的双重优点,不仅对染料罗丹明B和曙红Y具有良好的催化还原效率,而且可以在外加磁场作用下从溶液中快速有效的分离.催化还原反应速率与反应温度及Fe₃O₄@SiO₂-Ag催化剂用量有关,反应体系中表面活性剂和无机盐(Na₂SO₄)的存在也会影响催化剂的催化活性.该Fe₃O₄@SiO₂-Ag磁性纳米粒子在工业染料污染物处理方面具有应用前景.     

Latent Fingerprints Enhancement Using a Functional Composite of Fe3O4@SiO2-Au

A functional composite of Fe₃O₄@SiO₂-Au was prepared and used for latent fingerprint detection. Material characterization results confirmed the successful fabrication of the Fe₃O₄@SiO₂-Au composite. In latent fingerprint detection, the Fe₃O₄@SiO₂-Au composite provides a better performance than commercial copper powder and also gold nanoparticles. More importantly, the Fe₃O₄@SiO₂-Au composite can be used in both powder and suspension forms, and also for common surfaces including glass, polyethylene bags, and paper. The favorable pH range (2.0–5.0) for the compositein finger marks detection is much wider than that of the traditional multi-metal deposition method (pH ranging from 2.0 to 3.0). The mechanism for the Fe₃O₄@SiO₂-Au composite in fingerprint detection was explored and discussed. This study provides a favorable choice for a one-step deposition method for latent fingerprint detection.     

Mn(III) complex supported on Fe3O4 nanoparticles: magnetically separable nanocatalyst for selective oxidation of thiols to disulfides

A manganese(III) complex, [Mn(phox)₂(CH₃OH)₂]ClO₄ (phox?=?2-(2′-hydroxyphenyl)oxazoline), was immobilized on silica-coated magnetic Fe₃O₄ nanoparticles through the amino propyl linkage using a grafting process in dichloromethane. The resulting Fe₃O₄@SiO₂–NH₂@Mn(III) nanoparticles are used as efficient and recyclable catalysts for selective oxidation of thiols to disulfides using urea-hydrogen peroxide as the oxidant. The nanocatalyst was recycled several times. Leaching and recycling experiments revealed that the nanocatalyst can be recovered, recycled, and reused more than five times, without the loss of catalytic activity and magnetic properties. The recycling of the nanocatalyst in six consecutive runs afforded a total turnover number of more than 10,000. The heterogeneous Fe₃O₄@SiO₂–NH₂@Mn(III) nanoparticle shows more selectivity for the formation of disulfides in comparison with the homogeneous manganese complex.     

An efficient ‘on-water’ synthesis of 1,4-dihydropyridines using Fe3O4@SiO2 nanoparticles as a reusable catalyst

An ‘on-water’, efficient, high yielding, expeditious method has been developed for the synthesis of 1,4-dihydropyridine (1,4-DHP) derivatives via an one-pot multi-component condensation of dimedone or 4-hydroxycoumarine, aldehydes, and ammonium acetate using Fe₃O₄@SiO₂ nanoparticles as a recyclable heterogeneous catalyst. This method takes advantage of the fact that water, a green solvent is used in combination with Fe₃O₄@SiO₂ nanoparticles as catalyst which can be easily recovered magnetically and reused for further runs.     

聚乙烯基胺包裹Fe3O4@SiO2磁性微球用于Knoevenagel缩合（英文）简

Polyvinyl amine coated Fe₃O₄@SiO₂ composite microspheres with a core-shell structure were prepared and employed as a magnetic catalyst for Knoevenagel condensation under mild conditions. The catalyst can be readily recovered using a magnet and reused several times without loss in activity or selectivity. The performance of the magnetic base catalyst was compared with that of polyvinyl amine functionalized mesoporous SBA-15, which showed that the magnetic nanoparticles gave improved reaction rate and yield.     

Preparation and in vitro cytotoxicity study of poly (aspartic acid) stabilized magnetic nanoparticles

Biocompatible magnetic nanoparticles were prepared by co-precipitation method in the presence of poly (aspartic acid) (PAsp) as stabilizer, which was one of the most extensively studied and used poly(amino acids). As a biocompatible dispersant, PAsp was successfully attached to the Fe₃O₄ nanoparticles, which was approved by Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and thermogravimetric analysis (TGA). From X-ray diffraction (XRD) and vibrating sample magnetometry (VSM) measurement results, it was found that PAsp stabilized iron oxide nanoparticles possess excellent Fe₃O₄ crystal structure and superparamagnetic property. Compared with trisodium citrate stabilized magnetic nanoparticles, PAsp stabilized magnetic nanoparticles were biocompatible and with lower cytotoxicity, which makes it more applicable in medicine, biology and biomaterial science.     

Synthesis,characterization and application of sulfonic acid supported on ferrite–silica superparamagnetic nanoparticles

In this study, the synthesis of sulfonic acid supported on ferrite–silica superparamagnetic nanoparticles (Fe₃O₄@SiO₂@SO₃H) as a nanocatalyst with large density of acidic groups is suggested. This nanocatalyst was prepared in three steps: preparation of colloidal iron oxide magnetic nanoparticles (Fe₃O₄ MNPs), coating of silica on Fe₃O₄ MNPs (Fe₃O₄@SiO₂) and incorporation of sulfonic acid as a functional group on the surface of Fe₃O₄@SiO₂ nanoparticles (Fe₃O₄@SiO₂@SO₃H). The properties of the prepared magnetic nanoparticles were characterized using transmission electron microscopy, infrared spectroscopy, vibrating sample magnetometry, X‐ray diffraction and thermogravimetric analysis. Finally, the applicability of the synthesized magnetic nanoparticles was tested as a heterogeneous solid acid nanocatalyst for one‐pot synthesis of diindolyloxindole derivatives in aqueous medium. Oxindole derivatives were produced by the coupling of indole and isatin compounds with good to high yields (60–98%). Copyright © 2016 John Wiley & Sons, Ltd.     

Comparison of Cadmium Cd2+ and Lead Pb2+ Binding by Fe2O3@SiO2‐EDTA Nanoparticles – Binding Stability and Kinetic Studies

This study describes the synthesis and characterization of ethylenediaminetetraacetic acid (EDTA) functionalized magnetic nanoparticles of 20 nm in size – Fe₃O₄@SiO₂‐EDTA – which were used as a novel magnetic adsorbent for Cd(II) and Pb(II) binding in aqueous medium. These nanoparticles were obtained in two‐stage synthesis: covering by tetraethyl orthosilicate and functionalization with EDTA derivatives. Nanoparticles were characterized using TEM, FT‐IR, and XPS methods. Metal ions were detected under optimized experimental conditions using Differential Pulse Anodic Stripping Voltammetry (DPASV) and Hanging Mercury Drop Electrode (HDME) techniques. We compared the ability of Fe₃O₄@SiO₂‐EDTA to bind cadmium and lead in concentration of 553.9 μg L^?1 and 647.5 μg L^?1, respectively. Obtained results show that the adsorption rate of cadmium binding was very high. The equilibrium for Fe₃O₄@SiO₂‐EDTA‐Cd(II) was reached within 19 min while for the Fe₃O₄@SiO₂‐EDTA‐Pb(II) was reached within 25 minutes. About 2 mg of nanoparticles was enough to bind 87.5 % Cd(II) and 54.1 % Pb(II) content. In the next step the binding capacity of Fe₃O₄@SiO₂‐EDTA nanoparticles was determined. Only 1.265 mg of Fe₃O₄@SiO₂‐EDTA was enough to bind 96.14 % cadmium ions while 5.080 mg of nanoparticles bound 40.83 % lead ions. This phenomenon proves that the studied nanoparticles bind Cd(II) much better than Pb(II). The cadmium ions binding capacity of Fe₃O₄@SiO₂‐EDTA nanoparticles decreased during storage in 0.5 M KCl solution. Two days of Fe₃O₄@SiO₂‐EDTA storage in KCl solution caused the 32 % increase in the amount of nanoparticles required to bind 60 % of cadmium while eight‐days storage caused further increase to 328 %. The performed experiment confirmed that the storage of nanoparticles in solution without any surfactants reduced their binding capacity. The best binding capacity was observed for the nanoparticles prepared directly before the electrochemical measurements.