Synthesis and thermal decomposition of potassium peroxotitanate to K2Ti2O5

Potassium peroxotitanate was synthesized by the peroxo method. During the thermal decomposition K₂Ti₂O₅ can be obtained. The isothermal conditions for decomposition of K₂[Ti₂(O₂)₂(OH)₆]·3H₂O were determined on the base of DTA, TG and DSC results. DTA and TG curves were recorded in the temperature range 20 and 900°C at a heating rate of 10°C min^–1. The obtained intermediate compounds were characterized by means of quantitative analysis and IR spectroscopy. The mechanism of thermal decomposition of K₂[Ti₂(O₂)₂(OH)₆]·3H₂O to K₂Ti₂O₅ was studied. The optimal conditions for obtaining K₂Ti₂O₅ were determined (770°C for 10 h).     

CuO/Ti0.5Zr0.5O2催化剂对NO+CO反应的催化作用

环境治理是当今社会面临的一大主要问题。目前,城市空气污染日趋严重,特别是工厂和汽车排放的大量未燃烧的烃类、CO、NOx是主要的空气污染物。其中,氮氧化物(NOx)排放状况尤其严重,它的排放会给环境和人们生活带来严重危害,因此,如何有效地消除NOx已成为目前环境保护中一个非常     

Synthesis and thermal decomposition of bismuth peroxotitanate to Bi2Ti2O7

Bi-peroxotitanate was synthesized by a peroxo method and after thermal decomposition Bi₂Ti₂O₇ was obtained. DTA, TG and DSC curves of Bi₂[Ti₂(O₂)₄(OH)₆]5H₂O were recorded and used to determine isothermal conditions suitable for obtaining the intermediate samples corresponding to the phases observed during the thermal decomposition. The samples were identified by quantitative analysis, IR spectroscopy and X-ray analysis. The experimental results were used to propose a mechanism of thermal decomposition of the investigated compound to a nanosized Bi₂Ti₂O₇. The optimum conditions were also determined for obtaining Bi₂Ti₂O₇, which is applicable for piezosensors.     

Following the crystallisation of Bi2Mo2O9 catalyst by combined XRD/QuEXAFS

The formation ofβ-phase Bi₂Mo₂O₉ catalyst from a precursor precipitate has been studied using thein situ combined XRD/QuEXAFS technique and DSC during calcination. Accordingly the precursor was observed to undergo a number of changes in both the molybdenum (VI) coordination and long-range ordering during this heating. Initially the two other forms of bismuth molybdate (α-andγ-phases) were observed to form from the poorly crystalline precursor at about 230°C, however, theβ-phase eventually crystallised after prolonged heating at 560°C. Dedicated to Professor C N R Rao on his 70th birthday     

Crystallization kinetics of Ti20Zr20Cu60 metallic glass by isoconversional methods using modulated differential scanning calorimetry

The study of crystallization kinetics of amorphous alloys has been a matter of great interest for material researchers for past few decades, since it provides information about the kinetic parameters i.e., activation energy of crystallization and the frequency factor. These kinetic parameters can be calculated by model-free isoconversional methods. Isoconversional methods allow calculating the activation energy as a function of degree of conversion, α. Hence, these methods provide accurate results for multistep processes like crystallization. Model-free methods are categorized as linear and non-linear isoconversional methods. Linear methods are further classified as linear differential and linear integral isoconversional methods. In present work, we have used these isoconversional methods to study the effect of non-linear heating rate, employed by modulated differential scanning calorimetry (MDSC), on the non-isothermal crystallization kinetics of Ti₂₀Zr₂₀Cu₆₀ metallic glass. For Ti₂₀Zr₂₀Cu₆₀, MDSC curves clearly indicate a two-step crystallization process. Both crystallization peaks were studied based on the modified expressions for isoconversional methods by non-linear heating rate. The term corresponding to non-linearity comes out to be (A _T ω/2β)². The effect of non-linear heating rate on measurement of kinetic parameters by isoconversional methods is studied. The activation energy of crystallization is calculated for Ti₂₀Zr₂₀Cu₆₀ metallic glass for various degrees of conversion by linear integral isoconversional methods i.e., Ozawa–Flynn–Wall, Kissinger–Akahira–Sunose, and also with Friedman method which is a linear differential isoconversional method.     

Study of the evolution of CaCO3-V2O5 (1∶1) mixture at room temperature by thermal analysis

Reactivity of solid mixtures of crystalline V₂O₅ and basic compounds strongly increases at room temperature by means of water molecules adsorption process from a saturated atmosphere (100% RH). This is due, firstly, to a crystalline-amorphous V₂O₅ transformation and secondly to the formation of strongly acid V₂O₅ gels. In the present paper the evolution with time of the CaCO₃-V₂O₅ (11) mixture in the aforementioned conditions was studied by thermal analysis (TG, DTG and DSC), X-ray diffraction (XRD) and infrared spectroscopy (IR). The results confirmed the V₂O₅ gels formation which decomposed the basic CaCC₃ at room temperature through an acid-base mechanism reaction. A new crystalline compound was obtained which corresponded to a hydrated calcium metavanadate.This paper is a part of the L. Sobrados's PhD.     

Kinetics of crystallization of Zr52Cu18Ni14Al10Ti6 metallic glass

Metallic glasses have received considerable attention in comparison to normal metallic materials due to their superior physical and mechanical properties. These systems possess large under cooled region, ∆T (∆T = T _x − T _g where, T _x is crystallization temperature and T _g is glass transition temperature) and hence increased thermal stability against crystallization. Due to this, the study of their crystallization kinetics is important and interesting. It is interesting because of the fact that, crystallization becomes multi-step process due to several components present in these systems. In this paper, we report the experimental investigations of crystallization of Zr₅₂Cu₁₈Ni₁₄Al₁₀Ti₆ glassy alloy system, which is among the best non-beryllium containing glasses, using differential scanning calorimetry (DSC). The crystallization, as expected, consists of multiple steps. Interestingly, the peak heights of these steps vary with heating rate. At lower heating rates, first peak is most prominent and subsequently diminishes with increase in heating rate with last peak prominence visible at highest heating rate. Both, iso-kinetic and iso-conversional methods of analysis of kinetics of crystallization have been used to evaluate the activation energy and Avrami exponents and consistent results are obtained.     

Characterization and phase transformation study of TlSbSe2 crystals

TlSbSe₂ monocrystals were grown using the modified Bridgman–Stockbarger method and were characterized by transmission electron microscopy (TEM) and X-ray diffraction (XRD). Reflectivity spectra have been registered in the range 50 to 4000 cm^–1 for E parallel to a and E parallel to b polarizations, on the cleavage plane. A remarkable anisotropy at two directions was verified. With regard to previous observations, additional peaks were discriminated and the fundamental phonon parameters were determined using classical dispersion relations. The material presents a complex phase transformation – with two thermal effects – that was examined using differential scanning calorimetry (DSC). Non-isothermal measurements, at different heating and cooling rates (β), were used to study the thermal phenomena. The main effect is attributed to a structural displacement and the second one to a cation exchange procedure. The phase transformation temperature depends strongly on the cooling rate and the peaks are shifted by 30 K with the increase of this rate, on the contrary to the increase of the heating rate that has a smaller effect. Phenomena related with the influence of the previous, repeated heating and cooling cycles on the transformation are also examined and analytically discussed.     

Li4Ti5O12/(Cu+C)复合材料的制备及电化学性能

以Li₄Ti₅O₁₂,Cu(CH₃COO)₂·H₂O和C₆H₁₂O₆为前驱体,化学沉积与热分解结合合成锂离子电池负极材料Li₄Ti₅O₁₂/(Cu+C)。采用X-射线衍射(XRD)、扫描电子显微镜(SEM)、恒流充放电、循环伏安和电化学阻抗方法表征样品的结构、形貌和电化学性能。结果表明,Li₄Ti₅O₁₂表面包覆的Cu与C提高了Li₄Ti₅O₁₂电极材料的导电率,其循环性能和倍率性能得到有效地改善。在0.5C、1C和3C倍率下,经过50次充放电循环,放电比容量分别为168.2、160、140.6 mAh·g^-1,其容量保持率分别为88.7%、84.4%、71.2%。电化学阻抗测试表明,表面包覆的Cu与C使其电荷转移阻抗大幅度减少。     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。     

表面助剂改性对Cu/ZnO/Al2O3甲醇合成催化剂性能的影响

采用共沉淀-后浸渍方法制备了表面助剂改性的Cu/ZnO/Al₂O₃ (CZA)甲醇合成催化剂, 在固定床反应器上以合成气为原料分别考察了三种助剂(Zr、Ba和Mn)对CZA催化剂性能的影响; 以Zr为助剂时反应温度的影响; 并进行了催化稳定性试验. 利用粉末X射线衍射(XRD)、低温氮气吸脱附(N₂-sorption)、氧化亚氮(N₂O)反应吸附技术、X射线光电子能谱(XPS)、氢气程序升温吸脱附(H₂-TPD)、扫描电子显微镜(SEM)和高分辨透射电子显微镜(HR-TEM)技术对催化剂进行了表征.结果显示: 以Zr或Ba作为助剂能够明显提高CZA催化剂耐热前后的甲醇时空收率(STY); Mn的引入降低了CZA催化剂的耐热前活性; Zr的引入降低了CZA催化剂最高活性温度点, 增强了CZA催化剂的催化稳定性; 还原态CZA催化剂表面Cu⁰和ZnO都能吸附活化氢气, Cu⁰与ZnO的强相互作用有利于提高催化剂的性能, 耐热后催化剂性能的降低归因于Cu晶粒的长大. 在实验和表征结果基础上,提出了CZA催化剂上合成气制甲醇的“双向同步催化反应历程”.     

LiMn2O4表面包覆Li4Ti5O12的制备及倍率特性

采用固相法合成了尖晶石型LiMn₂O₄，并通过溶胶-凝胶法制备了不同物质的量的百分比含量Li₄Ti₅O₁₂包覆的正极材料。X-射线衍射和扫描电镜结果表明，Li₄Ti₅O₁₂微粒包覆在LiMn₂O₄的表面没有产生晶体结构的变化。实验电池在室温下，以1C，2C和5C倍率作充放电循环测试；结果表明，与未包覆的LiMn₂O₄相比，表面包覆Li₄Ti₅O₁₂微粒的正极材料在高倍率下具有更好的循环稳定性。     

The chemical and dielectric properties of epoxy/(Ba0.8Sr0.2)(Ti0.9Zr0.1)O3 composites for embedded capacitor application

The characteristics of epoxy/(Ba_0.8Sr_0.2)(Ti_0.9Zr_0.1)O₃ (BSTZ) composites are investigated for the further application in embedded capacitor device. The effects of BSTZ ceramic powder filler ratio on the chemical, physical and dielectric properties of epoxy/BSTZ composites are studied. Differential scanning calorimeter (DSC) thermal analysis is conducted to determine the optimum values of hardener agent, curing temperature, reaction heat, and glass transition temperature (T_g). The hardener reaction process starts at about 115 °C and completes at about 200 °C, for that it is appropriate to process of epoxy/BSTZ composites in the range of temperature. The highest glass transition temperature (T_g) of 155 °C is obtained at one equivalent weight ratio (hardener/epoxy). Only the BSTZ phase can be detected in the XRD patterns of epoxy/BSTZ composites. The more BSTZ ceramic powder is mixed with epoxy, the higher crystalline intensity of tetragonal BSTZ phase are revealed in the XRD patterns. The dielectric constant measured at 1 MHz increases from 5.8 to 23.6 as the content of BSTZ ceramic powder in the epoxy/BSTZ composites increases from 10 to 70 wt%. The loss tangents of the epoxy/BSTZ composites slightly increase with the increase of measurement frequency.     

不同形貌的Cu_2O:可控合成及光学性质(英文)

Cuprous oxide(Cu₂O) hexapodal branch structure with high uniformity was prepared by a solution phase route using sodium dodecyl sulfate as a capping agent. The shapes of Cu₂O crystal(flower-like structure, nanocube and nanoplate) were tuned by varying species and concentrations of surfactants to control the growth rate on different crystal planes of Cu₂O. Cu₂O nanostructures were characterized by UV-Vis spectroscopy, XRD, TEM and SEM. XRD result shows that the obtained Cu₂O belongs to cubic phase. TEM and SEM results demonstrate that specie and concentration of surfactants play a key role in the formation of various morphologies of Cu₂O. The formation mechanism is discussed. Moreover, the optical properties of the obtained Cu₂O are shape-dependent.     

Facile synthesis of Cu2O nanocube/polycarbazole composites and their high visible-light photocatalytic properties

Cu₂O nanocube/polycarbazole composites have been prepared by an one-pot solvothermal process using carbazole as a reductant. The polycarbazole layer not only protected and stabilized Cu₂O particles, but also prohibited the recombination of photogenerated electrons-holes pair and facilitated interfacial charge transfer between polycarbazole and Cu₂O. The composition, structure and morphology of the obtained products was systematically studied by X-ray powder diffraction (XRD), Field-emission scanning electron microscopy (FE-SEM), High-resolution transmission electron microscopy (HRTEM), Fourier transformation infrared spectroscopy (FT-IR), X-ray photoelectron spectroscopy (XPS) and UV-visible spectrophotometer. Furthermore, the visible-light photocatalytic behavior of the Cu₂O nanocube/polycarbazole composites on the methyl orange was investigated.     

Optimization of the electrophoretic deposition of YBa2Cu3O7−x superconducting large area coatings

Large area coatings (>10cm²) of the high temperature superconductor YBa₂Cu₃O_7–x (x = 0.1 – 0.2) (YBCO) have been prepared by scale up an electrophoretic deposition technique using silver sheets and Si-wafers coated with Ag or Au as substrates. Several parameters, like the kind of the solvent, the applied voltage, the distance between the electrodes, the initial concentration of the suspension and the temperature during the electrophoresis were investigated in order to attain high deposition rates, as well as uniform YBCO coatings with the proper stoichiometry. To obtain a strongly adherent and dense coating a subsequent appropriate sintering and annealing procedure has been developed. The coatings obtained were characterized for their stoichiometry and superconducting properties by X-ray diffraction (XRD), Raman spectroscopy and magnetic measurements. The homogeneity and thickness of the films and the average grain size of the deposited particles have been investigated by optical and scanning electron microscopy (SEM).     

Mechanism of formation of YBa2Cu4O8 superconductor in the sol-gel synthesis

It was shown that a single phase YBa₂Cu₄O₈ (124-phase) could be formed from gels at 1 atm oxygen pressure, and the mechanism of its formation was elucidated. It was found that there are two key routes for the sol-gel formation of the 124-phase, one involving the tetragonal YBa₂Cu₃O _y with a low concentration of oxygen defects (tetra-I phase) and the other involving the Ba₂Cu₃O_5.9 as important intermediates of the 124-phase. The rapid formation of these intermediate compounds from the gel was attributed to the small particle size of the oxides and carbonates precipitating at the initial stage of heating. It was thought that the small particles characteristic of sol-gel processing lead to the rapid formation of the intermediate compounds and subsequent precipitation of the 124-phase.     

Synthesis, structure and electrical properties of Cu3.21Ti1.16Nb2.63O12 and the CuOx-TiO2-Nb2O5 pseudoternary phase diagram

Subsolidus phase relations in the CuO_x-TiO₂-Nb₂O₅ system were determined at 935 °C. The phase diagram contains one new phase, Cu_3.21Ti_1.16Nb_2.63O₁₂ (CTNO) and one rutile-structured solid solution series, Ti_1−3xCu_xNb_2xO₂: 0<x<0.2335 (35). The crystal structure of CTNO is similar to that of CaCu₃Ti₄O₁₂ (CCTO) with square planar Cu²⁺ but with A site vacancies and a disordered mixture of Cu⁺, Ti⁴⁺ and Nb⁵⁺ on the octahedral sites. It is a modest semiconductor with relative permittivity ∼63 and displays non-Arrhenius conductivity behavior that is essentially temperature-independent at the lowest temperatures.     

Cu2SnSe3-Ag纳米复合物的合成及其热电性质研究

采用Schlenk line技术,通过一种简单的硒源热注射的方法合成了Cu_2SnSe_3(CTSe)纳米晶,同时采用胶体法得到了单分散性极好的、粒径为4nm左右的Ag纳米颗粒(Ag NPs),之后通过简单的滴加法向CTSe纳米晶基质中掺入了特定比例的Ag NPs,得到CTSe-Ag纳米复合物。通过X射线粉末衍射、透射电镜、高分辨透射电镜、红外光谱和热重分析等表征了样品的组成、结构和形貌。同时对合成样品的热电性质进行了研究,相关的测试结果表明,以CTSe为基体掺杂AgNPs的样品中,CTSe-1(mol)%Ag具有最佳的热电优值(ZT=0.23,655K),相较纯相CTSe(ZT=0.18,655K)提高了27%。