Li4Ti5O12/(Cu+C)复合材料的制备及电化学性能

以Li₄Ti₅O₁₂,Cu(CH₃COO)₂·H₂O和C₆H₁₂O₆为前驱体,化学沉积与热分解结合合成锂离子电池负极材料Li₄Ti₅O₁₂/(Cu+C)。采用X-射线衍射(XRD)、扫描电子显微镜(SEM)、恒流充放电、循环伏安和电化学阻抗方法表征样品的结构、形貌和电化学性能。结果表明,Li₄Ti₅O₁₂表面包覆的Cu与C提高了Li₄Ti₅O₁₂电极材料的导电率,其循环性能和倍率性能得到有效地改善。在0.5C、1C和3C倍率下,经过50次充放电循环,放电比容量分别为168.2、160、140.6 mAh·g^-1,其容量保持率分别为88.7%、84.4%、71.2%。电化学阻抗测试表明,表面包覆的Cu与C使其电荷转移阻抗大幅度减少。     

LiMn2O4表面包覆Li4Ti5O12的制备及倍率特性

采用固相法合成了尖晶石型LiMn₂O₄，并通过溶胶-凝胶法制备了不同物质的量的百分比含量Li₄Ti₅O₁₂包覆的正极材料。X-射线衍射和扫描电镜结果表明，Li₄Ti₅O₁₂微粒包覆在LiMn₂O₄的表面没有产生晶体结构的变化。实验电池在室温下，以1C，2C和5C倍率作充放电循环测试；结果表明，与未包覆的LiMn₂O₄相比，表面包覆Li₄Ti₅O₁₂微粒的正极材料在高倍率下具有更好的循环稳定性。     

Li4Ti5O12-聚苯胺复合材料的合成与表征

以醋酸锂和钛酸四丁酯为原料，以乙醇为溶剂，采用溶胶-凝胶法制备Li₄Ti₅O₁₂;以苯胺、过硫酸铵为原料，以盐酸为溶剂，采用原位聚合法合成Li₄Ti₅O₁₂-聚苯胺复合材料。采用X-射线衍射、红外光谱和电化学测试等对复合材料进行了表征。结果表明，聚苯胺的加入明显提高了Li₄Ti₅O₁₂的电子导电性能，Li₄Ti₅O₁₂-PAn复合材料具有比Li₄Ti₅O₁₂更好的高倍率性能和循环稳定性。0.1C和2.0C放电时Li₄Ti₅O₁₂-PAn的放电容量达到了191.3和148.9 mAh·g^-1，经80次循环后二者平均每次循环容量衰减率分别为0.13%和0.61%。     

三维连续结构Li4Ti5O12/石墨烯纳米复合材料:制备和其锂离子电池超长循环性能

利用具有三维连续纳米孔结构的热剥离石墨烯为骨架制备Li₄Ti₅O₁₂/石墨烯纳米复合材料。通过乙醇挥发法在热剥离石墨烯的纳米孔道内引入前驱物, 进一步高温热处理, 在热剥离石墨烯的孔道内原位形成Li₄Ti₅O₁₂纳米粒子。利用复合材料作为锂离子电池电极材料。电化学反应过程中, 热剥离石墨烯的三维连续结构确保了Li₄Ti₅O₁₂纳米粒子与石墨烯在长循环过程中的有效接触。因此, 复合材料表现出优异的循环稳定性。在5C下, 5 000次循环后, 其容量保持率高达94%。     

锂离子电池用Li4Ti5O12-碳复合材料的制备与电化学性能

Li₄Ti₅O₁₂-C composite was prepared by sol-gel method using ethyl alcohol as solvent, lithium acetate and tetrabutyl titanate as raw materials, and graphite as carbon source. Li₄Ti₅O₁₂-C composites were characterized by thermogravimertric(TG) analysis and differential thermal analysis(DTA), X-ray diffraction(XRD), Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM) and electrochemical tests. Results show that Li₄Ti₅O₁₂-C composite with 5% carbon containing can be obtained by annealing the precursor at 600 ℃ for 6 h in N₂ atomsphere. The composites can deliver a specific capacity of 167.1 mAh·g^-1, 99.0% and 105.1% of the capacity can be retained after discharged for 80 times at 0.1C and 2.0C, respectively. Compared with pure Li₄Ti₅O₁₂, Li₄Ti₅O₁₂-C composite shares larger discharge capacity, better cyclability and rate performance.     

三维尖晶石Li4Ti5O12纳米丝网状电极的构置与电化学性能

首次采用电纺丝技术结合高温退火成功地构置了含尖晶石Li₄Ti₅O₁₂的纳米纤维丝三维(3D)网状结构，并测量了三维电池的充放电性能。X射线衍射谱(XRD)、扫描电子显微镜(SEM)和电池循环性能测试等方法表征纤维丝3D结构和电化学性能。研究结果表明了Li₄Ti₅O₁₂纳米丝的零应变特性、构建的3D阵列的结构稳定性和在大电流密度下较好的充放电性能。显示了Li₄Ti₅O₁₂可作为3D电池的电极材料。     

V2O5-TiO2复合半导体光催化材料结构及光响应性能研究

采用溶胶凝胶法制备了V₂O₅-TiO₂复合半导体材料，通过Raman、XRD及UV-Vis DRS等实验方法研究了V₂O₅与TiO₂复合对材料表面组成、晶体结构以及光响应性能的影响。结果表明：钒加入后优先与TiO₂作用形成较为稳定的金红石型TiVO₄晶相，其中V⁴⁺是促进TiO₂发生相变的关键；随着钒加入量的增加，V₂O₅由表面高分散状态逐渐聚集形成晶相，并释放部分Ti⁴⁺使之形成锐钛矿型TiO₂晶相，使得体相中金红石型TiO₂的含量有所下降；复合后形成的TiVO₄晶相显著提高了材料对可见光的吸收率，并使其吸光域红移至460 nm左右。     

嵌入化合物LixMn2O4的水热浸渍合成研究

本文用水热浸渍二步法合成了尖晶石型Li_xMn₂O₄微粉，并对其采用XRD，SEM， ICP， XPS和IR等进行测试。结果表明产物为单相立方晶体，粒子尺寸范围0.15-0.5 μm, Li_xMn₂O₄中X为0.96，其中锰为Mn³⁺和Mn⁴⁺混合价态存在。该液相合成Li_xMn₂O₄材料的方法尚未见报道。     

球磨辅助高温固相法制备Li1.0Na0.2Ni0.13Co0.13Mn0.54O2正极材料及其性能

以乙酸盐(乙酸锂、乙酸钠、乙酸钴、乙酸镍、乙酸锰等)为原材料,采用球磨辅助高温固相法制备Li_1.0Na_0.2Ni_0.13Co_0.13Mn_0.54O₂正极材料。借助XRD、SEM等表征材料的结构和形貌,利用循环伏安、恒流充放电、交流阻抗等方法研究材料的电化学性能。结果表明,钠的掺杂导致颗粒表面光滑度降低,形成Na_0.77MnO_2.05新相。0.05C活化过程中,掺钠样品和未掺钠样品首次放电比容量分别为258.4 mAh·g^-1和215.8 mAh·g^-1,库伦效率分别为75.2%和72.8%;2C放电比容量分别为116.3 mAh·g^-1和106.2 mAh·g^-1。研究发现,掺钠可减小首次充放电过程的不可逆容量,提高容量保持率;改善倍率性能与容量恢复特性;降低SEI膜阻抗和电荷转移阻抗;掺钠后样品首次循环就可以基本完成Li₂MnO₃组分向稳定结构的转化,而未掺杂的样品需要两次循环才能逐步完成该过程;XPS结果表明,掺钠样品中Ni²⁺、Co³⁺、Mn⁴⁺所占比例明显提高,改善了样品的稳定性和电化学性能;循环200次后的XRD结果表明掺钠与未掺钠材料在脱嵌锂反应中的相变化过程基本一致,良好有序的层状结构遭到破坏是循环过程中容量衰减的主要原因。     

低温固相反应合成Li3V2(PO4)3正极材料及其性能

利用V₂O₅·nH₂O湿凝胶，LiOH·H₂O，NH₄H₂PO₄和C等作原料，通过低温固相还原反应在550 ℃焙烧12 h制备出Li₃V₂(PO₄)₃正极材料。采用XRD，SEM和电化学测试对Li₃V₂(PO₄)₃样品性能进行研究。XRD研究表明本法所合成的Li₃V₂(PO₄)₃同传统的高温固相反应法所合成的Li₃V₂(PO₄)₃一样同属于单斜晶系结构。SEM测试表明所合成的样品平均粒径大小约为0.5 μm且粒径分布较窄。电化学测试表明以0.2 C的倍率放电时，样品的首次放电容量为130 mAh·g^-1，室温下循环30次后其比容量为124 mAh·g^-1。     

Effect of surface fluorination and conductive additives on the electrochemical behavior of lithium titanate (Li4/3Ti5/3O4) for lithium ion battery

Effect of surface fluorination and conductive additives on the charge/discharge behavior of lithium titanate (Li_4/3Ti_5/3O₄) has been investigated using F₂ gas and vapor grown carbon fiber (VGCF). Surface fluorination of Li_4/3Ti_5/3O₄ was made using F₂ gas (3 × 10⁴ Pa) at 25-150 °C for 2 min. Charge capacities of Li_4/3Ti_5/3O₄ samples fluorinated at 70 °C and 100 °C were larger than those for original sample at high current densities of 300 and 600 mA/g. Optimum fluorination temperatures of Li_4/3Ti_5/3O₄ were 70 °C and 100 °C. Fibrous VGCF with a large surface area (17.7 m²/g) increased the utilization of available capacity of Li_4/3Ti_5/3O₄ probably because it provided the better electrical contact than acetylene black (AB) between Li_4/3Ti_5/3O₄ particles and nickel current collector.     

高倍率尖晶石型Li_4Ti_5O_(l2)/TiN锂离子电池负极材料的合成及其电化学性能

以乙酰丙酮(ACAC)为螯合剂、聚乙二醇(PEG)为分散剂,采用溶胶-凝胶法合成了尖晶石型Li4Ti5Ol2/TiN材料.考察了TiN膜对尖晶石型Li4Ti5Ol2锂离子电池负极材料电化学性能的影响.利用X射线光电子能谱(XPS)对Li4Ti5O12表面的TiN膜进行了分析.X射线衍射(XRD)和扫描电子显微镜(SEM)分析表明,Li4Ti5Ol2/TiN材料为结晶良好的亚微米纯相尖晶石型钛酸锂.电化学性能测试表明,该材料的首次放电比容量为173.0mAh·g-1,并且具有良好的循环性能,以0.2C、1C、2C、5C倍率放电进行测试,10次循环后比容量分别为170.6、147.6、135.6、111.0mAh·g-1,较之表面无TiN膜的钛酸锂材料表现出更好的倍率特性.循环伏安曲线(CV),交流阻抗图谱(EIS)进一步论证了TiN膜改善了尖晶石型Li4Ti5Ol2锂离子电池负极材料的电化学性能.     

Li ion diffusion in Li4Ti5O12 thin film electrode prepared by PVP sol-gel method

Li₄Ti₅O₁₂ thin films for rechargeable lithium batteries were prepared by a sol-gel method with poly(vinylpyrrolidone). Interfacial properties of lithium insertion into Li₄Ti₅O₁₂ thin film were examined by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and potentiostatic intermittent titration technique (PITT). Redox peaks in CV were very sharp even at a fast scan rate of 50 mV s⁻¹, indicating that Li₄Ti₅O₁₂ thin film had a fast electrochemical response, and that an apparent chemical diffusion coefficient of Li⁺ ion was estimated to be 6.8×10⁻¹¹ cm² s⁻¹ from a dependence of peak current on sweep rates. From EIS, it can be seen that Li⁺ ions become more mobile at 1.55 V vs. Li/Li⁺, corresponding to a two-phase region, and the chemical diffusion coefficients of Li⁺ ion ranged from 10⁻¹⁰ to 10⁻¹² cm² s⁻¹ at various potentials. The chemical diffusion coefficients of Li⁺ ion in Li₄Ti₅O₁₂ were also estimated from PITT. They were in a range of 10⁻¹¹-10⁻¹² cm² s⁻¹.     

Li4Ti5O12/CMK-3复合材料的制备及其作为锂离子电池负极材料的性能

将LiNO₃和Ti(OC₄H₉)₄填填充在有序介孔碳CMK-3 孔道中, 然后烧结合成了Li₄Ti₅O₁₂/CMK-3复合材料. 利用扫描电子显微镜(SEM)、透射电子显微镜(TEM)和X射线衍射(XRD)对其结构和微观形貌进行了表征. 利用差热-热重分析(TG-DTA)测试复合材料中Li₄Ti₅O₁₂的含量. 利用充放电测试、循环伏安和电化学阻抗技术考察了复合材料作为锂离子电池负极材料的性能. 发现Li₄Ti₅O₁₂分布在CMK-3孔道中及其周围, 复合材料的高倍率充放电性能显著优于商品Li₄Ti₅O₁₂, 复合材料中Li₄Ti₅O₁₂的比容量明显高于除去CMK-3的样品(在1C倍率时比容量为117.8 mAh·g^-1), 其0.5C、1C和5C倍率的放电比容量分别为160、143 和131 mAh·g^-1, 库仑效率接近100%, 5C倍率时循环100次的容量损失率只有0.62%. 本研究结果表明CMK-3明显提高了Li₄Ti₅O₁₂的高倍率充放电性能, 可能是CMK-3特殊的孔道结构和良好的导电性减小了Li₄Ti₅O₁₂的粒径并提高了其电导率.     

三维连续结构Li4Ti5O12/石墨烯纳米复合材料：制备和其锂离子电池超长循环性能

利用具有三维连续纳米孔结构的热剥离石墨烯为骨架制备Li4Ti5O12/石墨烯纳米复合材料。通过乙醇挥发法在热剥离石墨烯的纳米孔道内引入前驱物,进一步高温热处理,在热剥离石墨烯的孔道内原位形成Li4Ti5O12纳米粒子。利用复合材料作为锂离子电池电极材料。电化学反应过程中,热剥离石墨烯的三维连续结构确保了Li4Ti5O12纳米粒子与石墨烯在长循环过程中的有效接触。因此,复合材料表现出优异的循环稳定性。在5C下,5 000次循环后,其容量保持率高达94%。     

X-ray diffraction and Mössbauer spectroscopy studies of LiFe0.5Ti1.5O4 – A new primitive cubic ordered spinel

LiFe_0.5Ti_1.5O₄ was synthesized by solid-state reaction carried out at 900 °C in flowing argon atmosphere, followed by rapid quenching of the reaction product to room temperature. The compound has been characterized by X-ray powder diffraction (XRD) and ⁵⁷Fe Mössbauer effect spectroscopy (MES). It crystallizes in the space group P4₃32, a = 8.4048(1) Å. Results from Rietveld structural refinement indicated 1:3 cation ordering on the octahedral sites: Li occupies the octahedral (4b) sites, Ti occupies the octahedral (12d) sites, while the tetrahedral (8c) sites have mixed (Fe/Li) occupancy. A small, about 5%, inversion of Fe on the (4b) sites has been detected. The MES data is consistent with cation distribution and oxidation state of Fe, determined from the structural data.The title compound is thermally unstable in air atmosphere. At 800 °C it transforms to a mixture of two Fe³⁺ containing phases – a face centred cubic spinel Li_(1+y)/2Fe_(5−3y)/2Ti_yO₄ and a Li_(z−1)/2Fe_(7−3z)/2Ti_zO₅ – pseudobrookite. The major product of thermal treatment at 1000 °C is a ramsdellite type lithium titanium iron(III) oxide, accompanied by traces of rutile and pseudobrookite.     

Effect of sintering on the ionic conductivity of garnet-related structure Li5La3Nb2O12 and In- and K-doped Li5La3Nb2O12

Garnet-structure related metal oxides with the nominal chemical composition of Li₅La₃Nb₂O₁₂, In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ and K-substituted Li_5.5La_2.75K_0.25Nb₂O₁₂ were prepared by solid-state reactions at 900, 950, and 1000 °C using appropriate amounts of corresponding metal oxides, nitrates and carbonates. The powder XRD data reveal that the In- and K-doped compounds are isostructural with the parent compound Li₅La₃Nb₂O₁₂. The variation in the cubic lattice parameter was found to change with the size of the dopant ions, for example, substitution of larger In³⁺(r_CN6: 0.79 Å) for smaller Nb⁵⁺ (r_CN6: 0.64 Å) shows an increase in the lattice parameter from 12.8005(9) to 12.826(1) Å at 1000 °C. Samples prepared at higher temperatures (950, 1000 °C) show mainly bulk lithium ion conductivity in contrast to those synthesized at lower temperatures (900 °C). The activation energies for the ionic conductivities are comparable for all samples. Partial substitution of K⁺ for La³⁺ and In³⁺ for Nb⁵⁺ in Li₅La₃Nb₂O₁₂ exhibits slightly higher ionic conductivity than that of the parent compound over the investigated temperature regime 25-300 °C. Among the compounds investigated, the In-substituted Li_5.5La₃Nb_1.75In_0.25O₁₂ exhibits the highest bulk lithium ion conductivity of 1.8×10⁻⁴ S/cm at 50 °C with an activation energy of 0.51 eV. The diffusivity (“component diffusion coefficient”) obtained from the AC conductivity and powder XRD data falls in the range 10⁻¹⁰-10⁻⁷ cm²/s over the temperature regime 50-200 °C, which is extraordinarily high and comparable with liquids. Substitution of Al, Co, and Ni for Nb in Li₅La₃Nb₂O₁₂ was found to be unsuccessful under the investigated conditions.     

Synthesis, structure and electrical properties of Cu3.21Ti1.16Nb2.63O12 and the CuOx-TiO2-Nb2O5 pseudoternary phase diagram

Subsolidus phase relations in the CuO_x-TiO₂-Nb₂O₅ system were determined at 935 °C. The phase diagram contains one new phase, Cu_3.21Ti_1.16Nb_2.63O₁₂ (CTNO) and one rutile-structured solid solution series, Ti_1−3xCu_xNb_2xO₂: 0<x<0.2335 (35). The crystal structure of CTNO is similar to that of CaCu₃Ti₄O₁₂ (CCTO) with square planar Cu²⁺ but with A site vacancies and a disordered mixture of Cu⁺, Ti⁴⁺ and Nb⁵⁺ on the octahedral sites. It is a modest semiconductor with relative permittivity ∼63 and displays non-Arrhenius conductivity behavior that is essentially temperature-independent at the lowest temperatures.