硫酸钙晶须改性双马来酰亚胺树脂摩擦磨损性能的研究

研究了载荷、偶联剂及硫酸钙晶须用量对双马来酰亚胺树脂摩擦磨损性能的影响及材料的磨损机制.结果表明,当摩擦载荷较大时,树脂基体在摩擦过程中出现明显的塑性变形和裂纹,而经过硫酸钙晶须改性的复合材料体系则塑性变形和裂纹情况得到明显的改善,并且磨损量显著降低.载荷从200 N增大到300 N后,树脂基体的磨损机制从粘着磨损过渡为严重的疲劳磨损,添加晶须体系仍以粘着磨损为主.晶须添加量较小时,复合材料的磨损机理主要为粘着磨损,晶须添加量较高时,磨粒磨损占主导地位.     

稀土对镁合金AZ91D摩擦磨损性能的影响

研究了不同稀土含量对AZ91D镁合金摩擦磨损性能的影响，结果表明：在所研究的范围内，稀土镁合金的摩擦磨损特性明显优于基体合金，含与不含稀土镁合金的磨损速率都随载荷的增加而增加，磨损机制均发生了由轻微磨损向严重磨损的转变，稀土的加入细化了合金组织，改善了镁合金的综合性能，增强了磨损表面氧化膜的稳定性，提高了稀土镁合金的承载能力，有效地延迟了由轻微磨损向严重磨损的转变过程。     

稀土对玻璃纤维填充金属-塑料多层复合材料抗冲击磨损性能的影响

研究了稀土元素处理玻璃纤维填充金属－塑料多层复合材料在冲击载荷、干摩擦条件下的摩擦和磨损性能，并利用扫描电子显微镜（SEM）对磨损表面进行了观察和分析，结果表明，用稀土表面改性剂处理玻璃纤维表面，可以提高玻璃纤维与聚四氟乙烯之间的界面结合力，改善复合材料的界面性能，并有利于在偶件表面形成分布均匀、结合强度高的转移膜，使复合材料与偶件表面之间的对摩减轻，大幅度地降低了复合材料的磨损，从而使复合材料具有优良的摩擦性能和抗冲击磨损性能。     

稀土对MoSi2力学性能和抗氧化性能的影响

采用自蔓延和真空烧结方法制备了掺杂0．9％La2O3的MoSi2基复合材料，利用热重分析法，SEM和X射线考察了La2O3颗粒对MoSi2力学性能、抗氧化特性以及循环氧化后力学性能的影响。结果表明，与纯MoSi2相比，RE／MoSi2材料的弯曲强度和断裂韧性分别提高了46％和78％；稀土对MoSi2材料的强韧化机制主要是细晶强化、弥散强化和细晶韧化。RE／MoSi2的氧化增重是纯MoSi2的2．5倍，稀土使MoSiz材料的抗氧化性能降低。由于纯MoSi2材料氧化后的晶粒长大，其抗弯强度比氧化前降低了17％。稀土对MoSi2氧化时的晶粒长大倾向有抑制作用，使得RE／MoSi2材料的抗弯强度基本不变。     

偶联剂对钛酸钾晶须/双马来酰亚胺树脂摩擦磨损性能的影响

研究了不同偶联剂及钛酸钾晶须添加量对钛酸钾晶须 /双马来酰亚胺树脂复合材料的摩擦磨损性能的影响 .结果发现 ,钛酸钾晶须能明显提高复合材料的耐磨性 ,晶须的加入使材料的磨损率得到显著降低 ;钛酸钾晶须对材料具有一定的润滑性 ,添加晶须后材料的摩擦系数与树脂基体基本相当 ;偶联剂对复合材料的摩擦系数影响不大 ,但是合适的偶联剂对材料耐磨性的提高则具有明显的作用 .晶须添加量较低时 ,复合材料的磨损机理主要为较严重的粘着磨损 ,晶须添加量较高时 ,疲劳磨损占主导地位 .     

钛酸钾晶须填充环氧树脂复合材料的摩擦磨损特性

以提高环氧树脂的摩擦磨损性能为目的,研究了钛酸钾晶须(PTW)填充环氧树脂复合材料的滑动干摩擦磨损特性,着重探讨PTW含量、摩擦条件等对复合材料摩擦性能的影响.通过对复合材料磨损表面的形貌分析以及复合材料表面硬度的测定,探讨了复合材料的磨损机理.结果表明:PTW能明显提高环氧树脂耐磨性并降低其摩擦系数,w(PTW)=0.08的环氧树脂复合材料的耐磨性比纯环氧树脂提高近10倍,摩擦系数降低35%.     

稀土变质热锻模具铸钢高温磨损性能的研究

研究了稀土（RE）变质热锻模具铸钢的高温磨损性能，并与热锻模具钢H13钢和3Cr2W8V钢进行对比，探讨了稀土元素的作用和热锻模具铸钢的高温磨损机理。结果表明：随着RE加入量的增加，热锻模具铸钢的磨损率先减后增，RE加入量在质量分数为0．05％时热锻模具铸钢具有最佳的高温磨损性能。RE变质热锻模其铸钢的高温耐磨性明最高于H13钢和3Cr2W8V钢。高温磨损机理为氧化磨损和氧化物的疲劳剥落，磨屑为块状的Fe2O3和Fe3O4。     

La2O3-Mo5Si3/MoSi2复合材料的高温氧化行为

研究了0．8％La2O3-MosSi3／MoSi2复合材料在1200℃空气中的高温氧化行为。结果表明：0．8％稀土和MoSi3的加入，使材料的抗氧化性能降低。MosSi3含量越高，材料的抗氧化性能越差。当MosSi3含量低于30％时，在氧化初始阶段，质量变化呈直线下降，随着氧化的进行，氧化逐渐增重，材料表面形成较致密的SiO2阻止了材料的进一步氧化，使得氧化增重较小。而0．8％La2O3-40％Mo5Si3／MoSi2复合材料却出现了“粉化”现象。0．8％La2O3．MosSi3／MoSi2复合材料抗氧化性能的降低，归因于Mo5Si3差的抗氧化性和材料致密度的降低；另外，稀土和Mo5Si3的加入，细化了材料的晶粒，使晶界面积增加，加速了氧在晶界中的扩散，促进了材料的氧化。     

La2O3对Mo5Si3/MoSi2复合材料的改性研究

通过粉末冶金方法制备了Mo5Si3/MoSi2和La2O3/Mo5Si3/MoSi2复合材料,探讨了其烧结工艺.检测了其密度、维氏硬度、抗弯强度和断裂韧性,运用X射线衍射仪和扫描电镜（SEM）研究了La2O3对Mo5Si3/MoSi2复合材料显微结构和力学性能的改性影响.结果表明,La2O3/Mo5Si3/MoSi2复合材料的合理烧结温度为1600 ℃,比MoSi2材料提高了100 ℃; 稀土氧化物的加入细化了晶粒,且明显提高了材料的致密度、维氏硬度和抗弯强度; 其强化机制为细晶强化和弥散强化; 韧化机制为细晶韧化、裂纹偏转、裂纹分支和微桥接.     

水润滑下稀土处理碳纤维填充聚四氟乙烯复合材料摩擦学性能

分别用氧化法、稀土处理法、氧化后稀土处理法对碳纤维进行表面处理，然后开展拉伸试验来对不同方法处理的碳纤维填充聚四氟乙烯复合材料进行界面粘着研究，并在UMT-2MT型摩擦磨损试验机上对水润滑条件下聚四氟乙烯复合材料摩擦学性能进行研究，使用扫描电镜对磨损表面进行观察，研究结果表明稀土处理方法在提高复合材料摩擦学性能上优于氧化方法，稀土处理碳纤维填充的聚四氟乙烯复合材料优良的摩擦学性能来自于碳纤雏增强体与聚四氟乙烯基体间强的界面粘着力。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.