Synthesis of metal (Fe or Pd)/alloy (Fe–Pd)‐nanoparticles‐embedded multiwall carbon nanotube/sulfonated polyaniline composites by γ irradiation

Composites of multiwall carbon nanotubes (MWCNTs) and sulfonated polyaniline (SPAN) were prepared through the oxidative polymerization of a mixture of aniline, 2,5‐diaminobenzene sulfonic acid, and MWCNTs. Fe, Pd, or Fe–Pd alloy nanoparticles were embedded into the MWCNT–SPAN matrix by the reduction of Fe, Pd, or a mixture of Fe and Pd ions with γ radiation. Sulfonic acid groups and the emeraldine form of backbone units in SPAN served as the source for the reduction of the metal ions in the presence of γ radiation. The existence of metallic/alloy particles in the MWCNT–SPAN matrix was further ascertained through characterization by high‐resolution transmission electron microscopy (HRTEM), Fourier transform infrared spectroscopy, ultraviolet–visible spectroscopy, thermogravimetric analysis, and conductivity measurements. HRTEM pictures clearly revealed the existence of Fe, Pd, and Fe–Pd nanoparticles of various sizes in the MWCNT–SPAN matrices. There were changes in the electronic properties of the MWCNT–SPAN–M composites due to the interaction between the metal nanoparticles and MWCNT–SPAN. Metal‐nanoparticle‐loaded MWCNT–SPAN composites (MWCNT–SPAN–M; M = Fe, Pd, or Fe–Pd alloy) showed better thermal stability than the pristine polymers. The conductivity of the MWCNT–SPAN–M composites was approximately 1.5 S cm^?1, which was much higher than that of SPAN (2.46 × 10^?4 S cm^?1). Metal/alloy‐nanoparticle‐embedded, MWCNT‐based composite materials are expected to find applications in molecular electronics and other fields. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3355–3364, 2006     

A Polyethylene Nanocomposite Prepared via In‐Situ Polymerization

A novel organic/inorganic nanocomposite of polyethylene (PE) was prepared via in‐situ coordination polymerization. The Ziegler‐Natta catalyst was first supported on the surface of silicate nanowhiskers to subsequently initiate the polymerization of ethylene on the surface of these nanowhiskers. The nanowhiskers were encapsulated by polyethylene and became reinforcement fibers of the composite. The strong interaction between the uniformly dispersed nanowhiskers and the resin matrix resulted in the formation of a kind of organic/inorganic network providing good mechanical properties.     

The effect of gamma-radiation on polymer composites based on thermoplastic matrices

The effect of ⁶⁰Co γ-radiation on polymer composite materials (PCMs) based on reinforcing glass cloth, polyethylene (PE), polyamide (PA) and polypropylene (PP) matrices has been studied. It has been found that PCMs based on more durable PP and PA matrices have a substantially lower radiation resistance as compared to their PE-matrix analogs. More stable carbon-reinforced plastics based on the PE matrix also have a lower radiation resistance as compared to fiberglass plastics. High-strength PE fiber, PE film, and PE-matrix composites behave in fundamentally different manners under the action of radiation.     

Flame retardant polyamide 6 by in situ polymerization of ε-caprolactam in the presence of melamine derivatives

An improved method for preparing melamine cyanurate (MCA)based flame retardant polyamide 6 (FRPA6)materials has been proposed.This processing method,i.e.,improved in situ polymerization,was used to synthesize flame retardant PA6.In situ formed MCA nanoparticles were supposed to be linked to PA6 chains in the ε-caprolactam hydrolytic polymerization system to obtain startype polymers for the first time.Through TEM photographs,it can be found that the in situ formed MCA nanoparticles with diametric size of less than 50 nm,are nanoscaled,highly uniformly dispersed in the PA6 matrix.Synthesized flame retardant PA6 have good fire performance which can achieve UL-94 V-0 rating at 1.6 mm thickness with the presence of 7.34 wt.% MCA in the matrix.     

三元复合材料PANI／Ag／MWNT的电化学行为和比电容

通过原位聚合的方式在银纳米粒子/多壁碳纳米管（Ag/MWCNT）复合材料的表面成功聚合苯胺单体制备了聚苯胺/银纳米粒子/多壁碳纳米管（PANI/Ag/MWCNT）三元复合材料苯．通过对三元复合材料的结构以及表面形貌进行分析,表明聚苯胺层完全包覆了Ag/MWCNT复合材料,形成了核壳式结构．同时银纳米粒子则以单质晶体的形态存在于多壁碳纳米管与聚苯胺层之间．三元复合材料电极在1 mol/L的KOH溶液中具有极低的阻抗,而与聚苯胺电极相比,这些复合材料电极则表现出更低的电阻、更高的电化学活性和更好的循环稳定性．尤其是当苯胺和Ag：MWCNTs质量比为5：5时,该复合材料电极在0.25 A/g的电流密度下表现出最大的比电容值为160 F/g．     

Investigations on the structural,mechanical, thermal,and electrical properties of Ce-doped TiO2/poly(n-butyl methacrylate) nanocomposites

This study focused on the fabrication of poly(n-butyl methacrylate) (PBMA) nanocomposites with various concentrations of cerium-doped titanium dioxide (Ce–TiO₂) nanoparticles via in situ polymerization technique. The structural characterization and the material properties of all the composites were analyzed by UV–visible, FTIR, XRD, SEM, DSC, TG, and tensile strength measurements. The UV–visible and FTIR studies confirmed the effective inclusion of Ce–TiO₂ nanoparticles into the PBMA matrix. The change in amorphous morphology of PBMA to a crystalline structure was observed from the XRD pattern. The SEM morphology revealed the attachment of nanoparticles in the polymer matrix. The inclusion of Ce–TiO₂ nanoparticles enhanced the glass transition temperature, and thermal stability of the PBMA matrix was revealed from DSC and TG, respectively. The tensile strength of PBMA was greatly enhanced by the addition of Ce–TiO₂ nanoparticles. The AC conductivity, dielectric constant, and dielectric loss studies were also performed in the frequency range 10²–10⁶ Hz, and it was observed that addition of Ce–TiO₂ nanoparticles greatly enhanced the electrical properties of PBMA. The change in dielectric constant with the addition of nanoparticles was correlated with a theoretical modeling study. This work also extended to study the role of Ce–TiO₂ nanoparticles in the reinforcing mechanism of the nanocomposite by comparing the actual tensile strength of the composite with different theoretical modeling. The high dielectric constant and tensile strength of composite are beneficial in designing lightweight and highly efficient nanoelectronic materials based on the family of polybutyl acrylates.

     

Flame retardant polyamide 6 by in situ polymerization of ε-caprolactam in the presence of melamine derivatives

An improved method for preparing melamine cyanurate （MCA） based flame retardant polyamide 6 （FRPA6） materials has been proposed. This processing method, i.e., improved in situ polymerization, was used to synthesize flame retardant PA6. In situ formed MCA nanoparticles were supposed to be linked to PA6 chains in the ε-caprolactam hydrolytic polymerization system to obtain startype polymers for the first time. Through TEM photographs, it can be found that the in situ formed MCA nanoparticles with diametric size of less than 50 nm, are nanoscaled, highly uniformly dispersed in the PA6 matrix. Synthesized flame retardant PA6 have good fire performance which can achieve UL-94 V-0 rating at 1.6 mm thickness with the presence of 7.34 wt.% MCA in the matrix.     

原位聚合制备聚乙烯/蒙脱土(MMT)纳米复合材料的研究

利用MgCl₂在醇中溶解和蒙脱土(MMT)在醇中层间膨胀的特性,制备了MgCl₂/TiC_l4负载于MMT层间的MMT/MgCl₂/TiC_l4催化剂,并通过原位聚合合成了聚乙烯/蒙脱土纳米复合材料.经广角X射线衍射(WAXD)和透射电子显微镜(TEM)分析表明,蒙脱土片层在乙烯聚合过程中发生了层间剥离,以单片层或几片层共存的形式无规地分散于聚乙烯基质中.与分子量相近的纯聚乙烯相比,极低的蒙脱土含量(质量分数<1%)能使复合材料的屈服强度、拉伸强度和拉伸模量有很大提高.复合材料中蒙脱土片层以纳米尺寸在聚乙烯基质中的良好分布和对聚乙烯分子链运动的限制作用是力学性能提高的主要因素.     

Polypyrrole–multi-walled carbon nanotube nanocomposites synthesized in oil–water microemulsion

An oil–water microemulsion system, having been successfully used for synthesizing polypyrrole (PPy) nanoparticles, is introduced for preparing PPy–multi-walled carbon nanotube (MWCNT) nanocomposites via in situ chemical oxidative polymerization. The structures and the physical properties of the PPy–MWCNT nanocomposites are also investigated. The studies show that PPy can coat MWCNTs to form core–shell structure. The backbone structure of PPy is not damaged by the introduction of MWCNTs, and the PPy in the PPy–MWCNT nanocomposites is still amorphous as pure PPy. The conductivities of PPy–MWCNT nanocomposites are higher than that of pure PPy and are enhanced with the increase in the MWCNT–monomer mass ratio. Furthermore, a model is supposed to be used for illustrating the mechanism for PPy–MWCNT nanocomposite formation via in situ microemulsion synthesis.     

石墨烯/二氯化镁负载钛系齐格勒-纳塔催化剂制备及其乙烯聚合性能

石墨烯自2004年发现以来,由于其独一无二的优异性迅速成为科学家们的研究热点.由于石墨烯具有极其优异的电学、力学和热学等性能,因此被广泛应用于高性能聚合物基复合材料的制备.众所周知,纳米填料在聚合物中的分散状态以及与基体间的界面作用是构筑高性能聚合物纳米复合材料的关键因素.由于石墨烯极易团聚,难以通过传统的熔融共混法制备均匀分散的石墨烯增强-聚烯烃纳米复合材料.另一方面,聚烯烃通常需要在较高温度下才能溶于部分有毒溶剂(如:三氯苯和二甲苯等),因此溶液共混法也不适用于聚烯烃-石墨烯纳米复合材料的制备.有鉴于此,本文开发了一种共沉积法制备石墨烯/二氯化镁负载钛系齐格勒-纳塔催化剂的路线.通过原位聚合直接制备出石墨烯均匀分散的聚烯烃/石墨烯纳米复合材料.考察了石墨烯的加入量对催化剂形态及其催化乙烯聚合行为的影响.当石墨烯加入量较低时,多个石墨烯片被包裹于较大的催化剂粒子中.随着石墨烯加入量的增加,催化剂趋向于在石墨烯表面聚集.继续增加石墨烯量将导致石墨烯包裹催化剂粒子,降低过渡金属钛的负载效率.通过三乙基铝活化后,所制备的催化剂具有非常高的乙烯催化活性,所生成的聚乙烯/石墨烯纳米复合材料复制了催化剂的片状结构.同时,通过对所制备的聚乙烯/石墨烯纳米复合材料进行电子显微镜和X射线衍射分析可知,石墨烯均匀分散于聚乙烯基体中,并且没有任何团聚现象发生.该复合材料的热重分析表明,仅加入非常少量的石墨烯就可以使其具有比纯聚乙烯更高的热稳定性,当石墨烯加入量为0.66 wt%时,其5 wt%热分解温度较纯聚乙烯升高了54°C.同时,所制备聚乙烯/石墨烯纳米复合材料具有更优异的机械性能.因此,本研究提供了一个简单高效的高性能聚烯烃/石墨烯纳米复合材料的制备方法.     

Synthesis and characterization of polyethylene/clay–silica nanocomposites: A montmorillonite/silica‐hybrid‐supported catalyst and in situ polymerization

A novel approach to the preparation of polyethylene (PE) nanocomposites, with montmorillonite/silica hybrid (MT‐Si) supported catalyst, was developed. MT‐Si was prepared by depositing silica nanoparticles between galleries of the MT. A common zirconocene catalyst [bis(cyclopentadienyl)zirconium dichloride/methylaluminoxane] was fixed on the MT‐Si surface by a simple method. After ethylene polymerization, two classes of nanofillers (clay layers and silica nanoparticles) were dispersed concurrently in the PE matrix and PE/clay–silica nanocomposites were obtained. Exfoliation of the clay layers and dispersion of the silica nanoparticles were examined with transmission electron microscopy. Physical properties of the nanocomposites were characterized by tensile tests, dynamic mechanical analysis, and DSC. The nanocomposites with a low nanofiller loading (<10 wt %) exhibited good mechanical properties. The nanocomposite powder produced with the supported catalyst had a granular morphology and a high bulk density, typical of a heterogeneous catalyst system. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 941–949, 2004     

Incorporation of surface-derivatized gold nanoparticles into electrochemically generated polymer films

Stable colloidal solutions of gold nanoparticles surface-derivatized with a thiol monolayer have been prepared using two-phase (water–nitrobenzene) reduction of AuCl₄⁻ by sodium borohydride in the presence of 2-mercapto-3-n-octylthiophene (MOT). This kind of surface-functionalized gold nanoparticles can be easily incorporated into the poly(3-octylthiophene) (POT) films on electrode in the process of electrochemical polymerization leading to POT–gold nanoparticle (POT–Au) composite films. Scanning probe microscopy (SPM) and X-ray photoelectric spectroscopy (XPS) have been employed to characterize the surface-derivatized particles and the resulting films. The method of incorporation of nanoparticles into polymer by surface-derivatization and in situ polymerization can also be employed to prepare many other polymer–nanoparticle compostie materials.     

A new hydrocarbon material based on seabuckthorn (<Emphasis Type="Italic">Hippophae rhamnoides</Emphasis>) sawdust: A structural promoter of cobalt catalyst for Fischer–Tropsch synthesis

Aspects of the physicochemical properties of a hydrocarbon material based on seabuckthorn (Hippophae rhamnoides) sawdust are studied. The use of a hydrocarbon material based on sea buckthorn sawdust as a structural promoter of Со/C_Hip cobalt catalyst in the reaction of CO hydrogenation is shown to require an additional cycling stage in the mode of reduction and oxidation. The resulting mean size of the Co particles is found to be 18–19 nm and is considered acceptable for the synthesis of С5+ liquid hydrocarbons.     

Preparation of Conducting Composite Materials Based on Polymer Nanofibers and Polypyrrole

Conducting materials based on polypyrrole-modified nanofibers of polylactides of different molecular masses and copolymers of ε-caprolactam (–NH–(CH₂)₅–CO–) and hexamethylenediamine adipate (–H(CH₂)₆NHCO(CH₂)₄CO–) were prepared. As shown by scanning electron microscopy, oxidative polymerization of pyrrole on the polymer nanofiber matrix depends on the nanofib er hydrophilicity. The heterophase synthesis of polypyrrole on the surface of hydrophilic nanofibers of the aliphatic copolyamide allowed uniform coating of the material surface with polypyrrole nanoparticles. The surface resistivity of the composite material was about 0.4 kΩ sq^–1.     

Effect of nano-fillers on conductivity of polyethylene/low melting point metal alloy composites

A novel method for preparing conductive polyethylene(PE) composites has been developed. In the method, the powder of low melting point metal alloy(LMPA) is filled into the PE matrix by using twin screw extruder at a temperature below the melting point of the LMPA, and followed by a die drawing process at a temperature around the melting point of the metal alloy. It has been found that die drawing process, repeating the die drawing process and adding nano-fillers, such as montmorillonite(MMT) and multi-wall carbon nanotubes(MWCNTs), all help reduce the metal particle size in the PE matrix, thus improve the conductivity of the composite. The conductivity improvement is attributed to an increased number of the smaller metal particles. Therefore, conductive composites of polymer/metal alloy/nano-filler with high conductivity are possible to be prepared by using the new method.     

EB-promoted recycling of waste tire rubber with polyolefins

Despite the fact that more and more methods and solutions are used in the recycling of polymers, there are still some problems, especially in the recycling of cross-linked materials such as rubber. Usually the biggest problem is the lack of compatibility between the cross-linked rubber and the thermoplastic matrix. In this study we applied ground tire rubber (GTR) as recycled material. The GTR was embedded into polyethylene (PE) and polyethylene/ethylene-vinyl acetate copolymer (PE/EVA) matrices. In order to increase the compatibility of the components electron beam (EB) irradiation was applied. The results showed that the irradiation has a beneficial effect on the polymer–GTR interfacial connection. The EB treatment increased not only the tensile strength but also the elongation at break. The irradiation had also positive effect on the impact strength properties.     

Compatible Polyethylene/Polyvinyl Chloride Particle Hybrids Prepared by in‐situ Polymerization

Polyethylene/polyvinyl chloride (PE/PVC) hybrids were successfully prepared by a polymerization‐filling method. The catalyst for ethylene polymerization was supported on PVC particles, and ethylene was then polymerized in‐situ on the surface of the activated PVC. PVC particles could be well segmented and dispersed during in‐situ polymerization, and the prepared hybrids had an additional tangent peak between the glass transitions of polyethylene and PVC, indicating the formation of a compatible interlayer between nascent polyethylene and PVC during polymerization.     

Effective in situ synthesis and characteristics of polystyrene nanoparticle‐covered multiwall carbon nanotube composite

The higher surface area of selectively grown multiwall carbon nanotubes (MWCNTs) and the better proximity of the reactant species in in situ microemulsion polymerization were used to attach the polystyrene (PS) nanoparticles to the outer wall of MWCNTs. Attachment were achieved by replacing surfactant with PS nanoparticles. SEM showed that the MWCNTs and PS nanoparticles were distributed in the composite. High resolution transmission electron microscopy showed successful anchoring of PS nanoparticles to the outer wall of the MWCNTs. In addition, anchoring enhanced the Raman's G/D ratio of the MWCNT and degradation temperature in PS nanoparticles. A mechanism of attachment of PS nanoparticles on the outer wall of MWCNT was proposed. The modified MWCNTs exhibited good durability and dispersability in different organic solvents. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1523–1529, 2009     

高储能密度聚酰亚胺/钛酸钡/水滑石复合薄膜的制备与性能

利用零维纳米粒子与二维纳米片在聚合物基体中的协同分散,构筑纳米粒子/二维纳米片/聚酰亚胺(PI)三元复合体系,系统研究了零维-二维组合纳米填料对复合材料介电常数、击穿强度、储能密度以及机械性能的影响.结果表明:采用氟碳表面活性剂插层修饰可以将水滑石剥离为水滑石二维纳米片(HT),在此纳米片溶液中分散钛酸钡纳米粒子(BT),并进行聚酰亚胺的原位聚合.在聚合物溶液形成薄膜的过程中,二维纳米片和纳米粒子的协同作用抑制了各自的团聚,改善了2种纳米填料在聚合物薄膜中的分散状况.在所制备的PI/BT/HT复合薄膜中,HT有利于改善BT在PI基体中的均匀分散,提高了薄膜的击穿强度,进而提升了复合薄膜的储能密度.与仅加入20%BT相比,在聚酰亚胺中同时加入2种填料20%BT和1%HT时,击穿强度达到354.4 kV/mm,储能密度达到2.58 J/cm3,分别提高了12.4%和14.6%.因此,在纳米粒子/聚合物复合材料中增加少量二维纳米片就可以显著改善其性能,这种方法有望在更多纳米复合功能材料领域得到应用.     

Preparation and properties of Ni–Co–P/nano‐sized Si3N4 electroless composite coatings

Ni–Co–P/nano‐sized Si₃N₄ composite coating was successfully fabricated on aluminum alloys by electroless plating in this work. The surface and cross‐sectional morphologies, composition, microstructure, microhardness, friction and wear behavior of deposits were investigated with SEM, EDS, XRD, Vickers hardness and high‐speed reciprocating friction, respectively. It was found that a Ni–Co–P/nano‐sized Si₃N₄ composite coating on aluminum alloy substrate is uniform and compact. The existence of nano‐sized Si₃N₄ particles in the Ni–Co–P alloy matrix causes a rougher surface with a granular appearance, and increases the microhardness but decreases the friction coefficients and wear rate of electroless coatings. Meanwhile, the effects of heat treatment at 200, 300, 400 and 500 °C for 1 h on the hardness and tribological properties were researched. It is revealed that both of the microhardness and tribological properties of Ni–Co–P coatings and Ni–Co–P/Si₃N₄ composite coatings increase with the increase of heating temperature in the range of 200–400 °C, but show different behavior for the two coatings after annealing at 500 °C. Copyright © 2011 John Wiley & Sons, Ltd.