射频超导谐振腔中的电磁场研究

由高纯铌制成的射频超导谐振腔在高场时会出现Q值下降现象，这是高场下超导腔表面局部磁场增强所致. 为研究高场下超导腔表面的电磁场特性，用单cell超导腔设计了腔表面峰值磁场的研究实验. 通过对单cell超导腔表面峰值磁场的测量，可以确定超导腔焊缝及iris附近表面是否存在缺陷，以便进一步进行腔的处理来改进腔的性能.     

超导在加速器中的应用概况

文中简要回顾了世界上已建造的大型超导加速器,重点介绍未来的超导加速器方案,对超导新材料在加速器中的应用研究以及我国超导在加速器中的应用研究情况作了简要介绍.     

改进铜铌溅射型QWR超导腔性能的探讨

通过直流偏压二级溅射方法，在无氧铜腔体表面溅射一层铌膜，研制了铜铌溅射型射频超导1/4波长谐振腔(quarter wave resonator,QWR)，该腔主要用于重离子的加速，是北京放射性核束装置中后加速部分的预研项目.目前国际上很多实验室都在研究进一步提高铜铌溅射型QWR超导腔的性能，通过多种方法的实验研究，发现在无氧铜衬底与铌膜之间加入一层氮 化铌（NbN）薄膜，可以使得表面铌膜的超导温度转变点由原来的8.8K提高到了接近9.6K ，该方法有可能成为提高QWR腔加速性能的重要途径，目前进一步研究正 关键词： 溅射 QWR超导腔 氮化铌NbN 超导温度     

Investigation on the fabrication of the 3rd harmonic superconducting cavity for the SSRF storage ring

A third harmonic superconducting niobium cavity has been proposed for installation in the Shang-hai Synchrotron Radiation Facility (SSRF) storage ring to improve the Touschek lifetime. In order to investigate the feasibility of the superconducting cavity fabrication indigenously and the possibility to master the fabrica-tion techniques, cavities were fabricated from copper and niobium sheets by deep drawing and electron-beam welding, and a series of measurements, such as resonant frequency, shape dimensions and wall thickness, were carried out during this process. After analysis of various problems existing in the fabrication process, tech-nique improvements were proposed, and finally the precise shape as designed and resonant frequency within 1.2 MHz were achieved for the new completed cavities. In addition, full annealing was finally proved to be a good cure for niobium sheets' tearing up during deep drawing. By fabricating niobium cavities successfully, some problems to the next step were cleared. This paper introduces the process of cavity fabrication and its technique improvements towards forming, and the initial vertical test result of niobium cavity is also presented.     

Researches and Preliminary Experiments on Copper-Niobium Sputtered Low-β Superconducting Resonator

Superconducting resonator is the important component of a superconducting accelerator. The best choice of the acceleration cavity for heavy ion superconducting accelerator is quarter wave resonator (QWR). By sputtering a layer of niobium films of several microns on the OFHC copper substrate, good superconducting properties and acceleration properties of the cavity can be obtained. However, it is very difficult to get uniform niobium films by sputtering because the inner surface of the QWR is complicated. To deal with this problem, we developed a multiparameter adjusting method to control the sputtering process of different parts of the QWR. A layer of uniform niobium film with nice superconducting performance is obtained. The low temperature experiments with liquid helium show that the Cu Nb QWR has good superconducting characters. The Q value of the cavity is about 5×10⁸.     

溅射方法干式处理超导加速腔表面的研究与分析

详细研究了利用超高真空氩离子清洗技术发展的一种超导铌腔表面的“干式”处理方法,从微观和宏观角度分析了溅射处理对铌的表面特性和对超导腔性能的影响.与传统的“湿式”处理方法(化学抛光BCP和电抛光EP)相比,干式处理方法具有结构简单、容易控制、没有污染等优点,是一种很有潜力的超导腔处理方法,可以提高超导腔的性能. 关键词： 超导加速腔 溅射 形貌分析 残留电阻比RRR     

Cold RF test and associated mechanical features correlation of a TESLA-style 9-cell superconducting niobium cavity built in China

The RF performance of a 1.3 GHz 9-cell superconducting niobium cavity was evaluated at cryogenic temperatures following surface processing by using the standard ILC-style recipe. The cavity is a TESLA-style 9-cell superconducting niobium cavity, with complete end group components including a higher order mode coupler, built in China for practical applications. An accelerating gradient of 28.6 MV/m was achieved at an unloaded quality factor of 4×10⁹. The morphological property of mechanical features on the RF surface of this cavity was characterized through optical inspection. Correlation between the observed mechanical features and the RF performance of the cavity is attempted.     

超导腔垂直测量系统中的磁屏蔽

简要介绍空间磁场对纯铌超导加速腔性能的影响,以及在超导腔垂直测量时对空间磁场进行有效屏蔽的方法.由于多数磁性材料对应力和温度变化非常敏感,而且国内缺乏在低温下相关磁屏蔽材料性能的数据,为此对8种国产铁磁和软磁材料在低温下的初始磁导率进行了测量,并给出了相应的测试结果.最后介绍了作者研制的1.3GHz超导腔垂直测量低温恒温器内置式磁屏蔽装置及其性能.     

Study on the 1.3 GHz low loss shape superconducting cavities at IHEP

As part of the international research program on the superconducting cavity for the International Linear Collider (ILC) R&;D on the 1.3 GHz low loss superconducting cavities has been carried out at the Institute of High Energy Physics (IHEP) since 2005. A design of 1.3 GHz low loss cavity shape was proposed and six single-cell cavities of different niobium material were successfully fabricated with standard technology. In this study our priority was on large grain (LG) cavities. The two LG cavities were treated with complete procedures of surface treatments based on chemical polishing (CP) without electro polishing (EP) at IHEP. The two LG cavities and a fine grain cavity were sent to KEK for vertical testing. All the three cavities reached accelerating gradients higher than 35 MV/m and the maximum gradient of 40.27 MV/m was achieved in the LG cavity. This paper presents the process of the vertical RF tests and the comparison of the LG and fine grain cavities's performance.     

上海光源500MHz超导腔水平测试

上海光源是能量为3.5 GeV的第三代先进中能同步辐射光源,其储存环上安装了三台超导高频腔补偿电子因同步辐射等原因丢失的能量。为保障上海光源的长期稳定高效运行,中国科学院上海应用物理研究所和上海市低温超导高频腔技术重点实验室共同研制了具备低高次模损失参数和可承受更高入射功率的新型500 MHz超导腔,作为上海光源在线运行超导高频腔的备用腔。超导铌腔经低温垂直测试达到所需加速性能后,需要与高功率输入耦合器、高次模吸收器、低温恒温器等集成并完成水平测试,获得超导腔模组的加速性能、低温性能和真空性能。介绍了超导腔备用腔的研制、集成和测试过程,采用文丘里(Venturi)校准法获得模组的静态功耗反应模组的低温性能,并通过高功率测试获得了超导腔备用腔模组的加速性能。测试结果表明:自主研制的500 MHz超导腔备用腔满足上海光源的工作需求,在超导腔的加速腔压为2.0 MV时,无载品质因数为1.2×109 @4.2 K,且低温模组的静态热损耗为36.1 W。     

北京大学国产大晶粒铌材超导腔的性能研究

大晶粒铌材是射频超导领域的研究热点之一. 采用大晶粒铌材的射频超导谐振腔, 其后处理工艺可以大大简化. 北京大学对此进行了深入细致的研究, 自主研制了采用国产大晶粒铌材的射频超导腔, 对这些超导腔进行了简单的表面处理, 包括标准的化学抛光(BCP)和120℃低温烘烤处理, 未进行非常复杂的电抛光处理, 低温性能测试结果表明其低温超导性能优越, 大晶粒1.3GHz超导腔的加速梯度达到了43.5MV/m, 为我国超导加速器的国产化打下了基础.     

Manufacture of superconducting niobium cavity parts by hydropercussion punching

A complete cycle of manufacturing all parts of superconducting niobium cavities which comprise two half-cells, two drift tubes, and two flanges each has been developed. The cavity half-cells are manufactured by hydropercussion punching, which has a number of advantages over the instrumental stamping technique. For the first time, the diagram of formability of ultrapure niobium has been experimentally obtained for hydropercussion punching and the key parameters of the process have been determined that ensure complete deep-drawing of workpieces, viz., the value of the limit drawing ratio of ultrapure niobium that is 1.92 at a specific impact energy of 0.42 MJ/m². The deviations of the half-cell dimensions from the rated values do not exceed 0.1 mm. Production tools required for all manufacturing steps have been created. The parameters of machining of the niobium cavity parts prior to welding have been experimentally established.     

Great progress in developing 500 MHz single cell superconducting cavity in China

Superconducting cavities have been adopted in many kinds of accelerator facilities such as synchrotron radiation light source, hard X-ray free electron laser linac, colliders and energy recovery linacs (ERL). The 500 MHz superconducting cavities will be a candidate to be installed in the high current accelerators and high current ERLs for their large beam aperture, low higher order modes impedance and high current threshold value. This paper presents great progress in the whole sequence of developing 500 MHz superconducting cavity in China. It describes the first in-house successful development of 500 MHz single cell superconducting cavity including the deep-drawing of niobium half cells, electron beam wielding of cavity, surface preparations and vertical testing. The highest accelerating gradient of the fabricated cavity #SCD-02 higher than 10 MV/m was obtained while the quality factor was better than 4×10⁸ at 4.2 K, which has reached the world level of the same kind of cavities.     

Study on the 1.3 GHz low loss shape superconducting cavities at IHEP

As part of the international research program on the superconducting cavity for the International Linear Collider (ILC) R&D on the 1.3 GHz low loss superconducting cavities has been carried out at the Institute of High Energy Physics (IHEP) since 2005. A design of 1.3 GHz low loss cavity shape was proposed and six single-cell cavities of different niobium material were successfully fabricated with standard technology. In this study our priority was on large grain (LG) cavities. The two LG cavities were treated with complete procedures of surface treatments based on chemical polishing (CP) without electro polishing (EP) at IHEP. The two LG cavities and a fine grain cavity were sent to KEK for vertical testing. All the three cavities reached accelerating gradients higher than 35 MV/m and the maximum gradient of 40.27 MV/m was achieved in the LG cavity. This paper presents the process of the vertical RF tests and the comparison of the LG and fine grain cavities's performance.     

The First Nine-Cell TESLA Cavity Made in China

A totally home-made 9-cell TESLA type superconducting cavity is mane at Peking University. The cavity abrication is according to DESY specification. The cavity is made of high purity niobium from OTIC, Ningxia. The electron beam welding is carried out at Harbin Institute of Technology, Harbin. By the cooperation, the cavity is tested at Thomas Jefferson National Accelerator Facility, USA. The preliminary result shows the acceleration gradient Eacc is 23 MV/m without quench and has potential for improvement.     

Computation of single-cell superconducting niobium cavity for accelerator of electrons and positrons

Computations of the accelerator section of the International Linear Collider (ILC), which consists of superconducting niobium cavities, are performed for conditions of the maximum energy transfer to electrons that travel along the cavity axis. A mathematical model and software packages are created for the computation of the electric characteristics and profile of a single-cell cavity. A computer-based synthesis of the cavity shape that yields the required electric characteristics is performed. The promising design variants of a single-cell cavity, with which a quality factor of 10¹⁰ is provided at a working frequency of 1.3 GHz, are found to optimize the construction and manufacture of a single-cell cavity. The electric characteristics of a chain of single-cell cavities are computed.     

射频超导腔加速性能的改进

 为提高超导加速腔的加速梯度和Q值，改进了薄膜型超导腔的加速性能。研究证明，对于铜铌溅射腔，在无氧铜衬底和铌膜之间加入NbN 层可以提高铌膜的超导转变温度，改善晶格结构；对纯铌超导腔提出了改进方法，在传统的纯铌超导腔表面制备多层的超导-绝缘-超导复合膜可以屏蔽Nb腔表面的界面场，提高超导腔的临界磁场，从而提高了铌腔的加速梯度。     

Superconducting linear accelerator system for NSC

This paper reports the construction of a superconducting linear accelerator as a booster to the 15 UD Pelletron accelerator at Nuclear Science Centre, New Delhi. The LINAC will use superconducting niobium quarter wave resonators as the accelerating element. Construction of the linear accelerator has progressed sufficiently. Details of the entire accelerator system including the cryogenics facility, RF electronics development, facilities for fabricating niobium resonators indigenously, and present status of the project are presented.     

Degradation of the second critical magnetic field in multilayered composites with nanodimensional layers of niobium and Nb-Ti superconducting alloy

Multilayered tapes containing layers of superconducting niobium alloys with 30 and 31 wt % Ti and separated by niobium layers were investigated. The layers were ∼140 to ∼10 nm thick. Effective pinning of superconducting vortex filaments was observed on the interlayer Nb-NbTi interfaces. It was established that second critical magnetic field H _c2 decreased as the layer thickness decreased. With thin layers, its magnitude depended on the orientation of rolling the tape with respect to the external magnetic field. Results are explained by the proximity effect.     

Real metal parameters of niobium from the attenuation of transverse ultrasonic waves

Measurements of the attenuation of shear waves in superconducting niobium along [100] for frequencies from 18 to 105 MHz show that the Fermi surface deformation parameter for shear strains is large.