1-苯基-3-甲基-4-苯甲酰基-5-吡唑酮与甲基膦酸二(1-甲基庚基)酯对Pb(Ⅱ)、Cd(Ⅱ)和Cu(Ⅱ)的萃取机理研究

本文用两相滴定法研究了1-苯基-3-甲基-4-苯甲酰基-5-吡唑酮(PMBP,简写为HA)与甲基膦酸二(1-甲基庚基)脂(P₃₅₀,简写为B)对Pb²⁺、Cd₂₊和Cu²⁺离子在不同的有机溶剂中的萃取机理.确定了萃合物的组成分别为:MA₂(M=Pb²⁺、Ca²⁺、Cu²⁺);MA₂·HA(M=Cd²⁺);MA₂·B(M=Pb²⁺、Cd²⁺)和MA₂·2B(M=Cd²⁺),同时求得了相应的萃合常数β值.     

硫酸水溶液中铅阳极膜形成及其结构的非现场FTIR反射吸收光谱—电化学研究

本文用非现场红外反射吸收光谱方法和电化学循环伏安法研究了1.0mol·dm^-3H₂SO₄中-0.6至2.5伏电势范围内(相对SCE)Pb阳极膜的形成及其可能的结构.在此电势区内Pb阳极膜中始终存在硫酸铅或碱式硫酸铅,其中SO₄^2-主要以桥式双齿配位方式与Pb²⁺结合.另外,上述电势范围内生成的膜中无可检测量的H₂O和OH^-存在.     

掺杂F-对PbO2阳极性能和电催化活性的影响

采用热分解-电镀法制备了Ti基PbO₂阳极(PbO₂阳极)和F^-掺杂PbO₂阳极(F-PbO₂阳极)。应用XRD和SEM技术对这两种电极进行了表征，采用加速电解寿命测试研究了其在硫酸溶液中的电解稳定性。结果表明，F-PbO₂阳极的寿命远大于PbO₂阳极的寿命，在4-氯苯酚(4-CP)的电催化降解过程中，F-PbO₂阳极表现出比PbO₂阳极较强的催化活性。本文对F^-掺杂提高PbO₂阳极性能和电催化活性的机理进行了探讨。并应用高效液相色谱确定了4-CP在F-PbO₂阳极上的降解历程。     

溶液中N-乙酸基取代氮氧杂大环及其配合物稳定性研究

用pH电位滴定法在25℃,0.5mol·L^-1KNO₃水溶液中测定了三种大环化合物:H₂L¹(1,12-二氮杂-3,4:9,10-二苯并-5,8-二氧杂环十五烷-N,N'-二乙酸);H₃L²(1,12,15-三氮杂-3,4:9,10-二苯并-5,8-二氧杂环十七烷-N,N',N″-三乙酸)和H₂L³(1,15-二氮杂-3,4:12,13-二苯并-5,8,11-三氧杂环十八烷-N,N′-二乙酸)的逐级质子化常数.又测定了它们与Cu²⁺、Ni²⁺、Pb²⁺配合物的稳定常数,以及H₂L³与镧系金属La³⁺、Pr³⁺、Nd³⁺、Eu³⁺、Sm³⁺、Gd³⁺、Dy³⁺、Yb³⁺配合物的稳定常数.讨论了三种大环化合物质子化的一般顺序及其与各种离子配位时稳定性选择规律.说明了影响配位稳定性的有关因素.     

氯化二(羟胺根)·(羟胺—O)·水合氧钒(Ⅴ)[VO·(NH2O)2·(NH3O)·H2O]Cl的晶体结构

调节硫酸氧钒与盐酸羟胺溶液至pH～4制得的题目晶体属空间群P2₁/n,晶胞参数a=8.201,b=8.597,c=9.947A,β=93.00°,Z=4.结构解出精修后R因子为0.069.结果表明,不对称单位中二个羟胺根以侧接态与VO³⁺配位,另一羟胺取端接态以O占据V的第五赤道配位位置,配位水处于氧钒基强键反位,Cl^-则在配阳离子界外以平衡电荷,晶体对的化学式确证为[(VO³⁺)(NH₂O^-)₂(NH₃O)(H₂O)][Cl^-]     

2,6—二乙酰吡啶类双希夫碱配合物的研究——Ⅲ.Co(Ⅱ)、Ni(Ⅱ)、Zn(Ⅱ)、Pb(Ⅱ)和Cd(Ⅱ)配合物的合成和表征

制备了由2,6—二乙酰吡啶和肼基硫代甲酸酯衍生的希夫碱C₅H₃N[CH=NNHC(S)XR]₂(X=S,R=CH₃、C₆H₅CH₂;X=O,R=C₆H₅CH₂).离析出类型为MC₅H₃N[CH=NN=C(S)XR]₂(M=Co²⁺、Ni²⁺、Zn²⁺、Pb²⁺和Cd²⁺)的希夫碱配合物.配合物为元素分析、红外、可见—紫外光谱以及磁化率测量所表征.结果指出:上述希夫碱均为N₃S₂型五齿配体.     

LnBaB9O16︰Pr3+(Ln=La,Y)中Pr3+的双光子发射

在216nm紫外光激发下, LnBaB₉O₁₆︰Pr³⁺中的Pr³⁺离子可以发生双光子发射;稀土离子在LnBaB₉O₁₆中处于非中心对称格位,Pr³⁺离子的4f5d能态高于¹S₀能级,可以发生从¹S₀能级到中间能态及基态的双光子跃迁发射;LaBaB₉O₁₆中与稀土离子近邻的硼酸根离子为BO₄,相应的B—O振动频率较低,³S₀与¹D₂之间的无辐射跃迁几率比较小,可以出现从³S₀能级的发射.在YBaB₉O₁₆中,Pr³⁺的4f5d能态低于¹S₀能级,不能发生双光子发射.     

光/电/化学催化降解水中酸性大红3R染料的研究

以高纯石墨电极、TiO₂/Ti薄膜电极和甘汞电极, 分别为阴极、阳极和参比电极, 设计研制出了新型光-电-化学催化集成反应器. 在紫外光和外加电场的作用下, 不仅TiO₂/Ti薄膜电极能对阳极槽中的酸性大红3R进行光电催化降解脱色, 且在阴极上产生的过氧化氢及其与亚铁离子形成的H2O₂/Fe²⁺催化体系, 对阴极槽中的染料溶液也有良好的脱色降解作用. 该催化集成反应器充分利用了光生空穴和光生电子, 实现了在阳、阴两极同时对染料进行降解脱色处理, 达到了“双极双效”的目的. 实验表明, 当用0.02 mol·L^−1硫酸钠为支持电解质、初始pH = 3和阴极电位−E_c = 0.66V的条件下, 阴极槽和阳极槽对30 mg·L^−1酸性大红3R溶液的脱色降解率分别达到92%和60%, 与双极单效的光电催化相比, 效率显著提高.     

SbOx+SnO2中间层对Ti/MnO2电极性能的影响

采用热分解方法制备了含SbO_x+SnO₂中间层的钛基二氧化锰电极. 在0.5 mol·L^-1 H₂SO₄溶液中对添加和没有添加SbO_x+SnO₂中间层的二氧化锰阳极进行了加速电解试验. 采用极化曲线和循环伏安曲线测量电极的析氯反应. 用循环伏安曲线和电化学阻抗谱来分析电极电解过程中内部结构和表面的变化. 结果表明, 二氧化锰阳极钝化失效的主要原因是绝缘的TiO₂层的生成和变厚. 引入中间层可以降低钛基体和活性涂层间的电阻, 并且在电解过程中, 可以显著延缓接触电阻的升高, 从而可以显著提高其寿命.     

硫酸溶液中苯酚在Ti/PbO2电极上的循环伏安研究

用循环伏安法研究了Ti/PbO₂电极在苯酚硫酸溶液中的电催化作用. 结果表明, 在硫酸溶液中, Ti/PbO₂阳极对苯酚具有电催化氧化作用. 如果苯酚浓度较低, 产生的吸附态羟基自由基可以将苯酚氧化, 直至完全矿化. 当苯酚浓度较高或产生的羟基自由基量相对较小时, 苯酚或中间产物可吸附在电极表面, 降低电极的真实表面积, 减少电极的活性点, 阻止反应物接近电极表面, 抑制苯酚的进一步氧化. 随着电解时间的延长, 这些吸附物由于逐渐被氧化, 电极活性恢复.     

F-和Fe3+掺杂对Ti基PbO2阳极性能的影响

采用热分解-电镀法制备了Ti基PbO2,阳极(Ti/PbO2),F-掺杂PbO2阳极(Ti/F-PbO2),Fe3+掺杂PbO2阳极(TiP/Fe-PbO2)和F-,Fe3+共掺杂PbO2,阳极(Ti/F-Fe-PbO2).采用XRD和EDX测试对电极进行了表征,应用加速电解寿命测试和电催化降解4-氯苯酚(4-CP)污水,考察了F-掺杂,Fe3+掺杂和F-,Fe3+共掺杂对PbO2阳极稳定性及电催化活性的影响.结果表明,Ti/F-PbO2和Ti/FePbO2阳极有相近的电催化降解活性,但与Fe3+掺杂相比,F-掺杂大大提高了PbO2阳极的加速电解寿命.对Ti/F-Fe-PbO2阳极,Fe3+掺杂改善了其导电性能.同时F-掺杂提高了阳极的稳定性能,使其有较长的电解寿命.与Ti/PbO2,Ti/F-PbO2和Ti/Fe-PbO2阳极相比,Ti/F-Fe-PbO2阳极的电催化降解活性显著提高,这不仅与其导电性能的改善有关,更与F-掺杂和Fe3+掺杂对4-CP降解的表面协同作用有关.     

钛基二氧化铅电极电沉积制备过程中的立体生长机理

采用恒电位的方法在涂有SnO2＋Sb2O5中间层的Ti基体上电沉积制备了不同颗粒尺度的Ti/PbO2电极, 利用XPS, XRD和SEM等方法对Ti/PbO2电极电沉积制备过程中电极的结构、表面形貌等物理化学性能进行了研究. 结果表明, Ti/PbO2电极涂层中Pb元素在138.2～138.4 eV之间有明显的Pb4f7/2峰, 表明电极表面上主要得到的是PbO, XRD和XPS分析结果证明电极涂层体相生成的是PbO2. 基于Ti/PbO2涂层的形成是不同晶面生长过程的事实, 提出Ti/PbO2电极的立体生长机理.     

Application of TiO2-nanotubes/PbO2 as an anode for the electrochemical elimination of Acid Red 1 dye

Journal of Solid State Electrochemistry - In this study, galvanostatic electrolysis, through the use of the platinum supported on Ti (Ti/Pt) and Ti/TiO2-nanotubes/PbO2 anodes, was conducted in an...     

Synergetic effects during sputter-assisted depth profiling: Growth-dominated topography development on InP and a model of the atomic mechanism

Growth-dominated extreme topography development on ionbombarded wafers of InP is reported and is explained in terms of the micro region model presented in summary form. This model postulates the existence of an ion-bombardment-produced ensemble of crystallites and non-crystalline aggregations of atoms (composed of the substrate material, of dopant and of oxygen from the native oxide layer) where the majority of InP micro regions is so small (nanometer dimensions) that most interstitials created in collision events between bombarding ions and atoms of the micro region can reach an interfacial boundary rather than recombine with a vacancy from the same or another collision event. These atoms are then transported via interfacial boundaries and over the surface to screw dislocations where crystal stubs proceed to grow until the damage rate by ion bombardment overtakes the growth rate. Ion-bombardment-induced compressive stresses favour diffusion towards the surface. Temperature transients within micro regions assist both interfacial diffusion and damage repair. The topography is a result of competition between growth and sputtering. Different growth rates cause different topographies. The development of an extreme topography can be suppressed by oxygen flooding of the sputtered surface, by simultaneous electron beam scanning, as well as by Cs⁺ ion bombardment.     

Point defects in (Ti, Fe)N hard coatings, a Mössbauer study

Reactive magnetron sputtered layers of nitridic hard coatings (e.g. TiN) often show high intrinsic stresses caused by the differences of the thermal expansion coefficients of the layer and the substrate and the incorporation of atoms of sputtering and/or reactive gas atoms in lattice voids. The decrease of hardness and stresses of such layers after heat treatment seems to originate from the out-diffusion of interstitial excess reactive gas atoms (e.g. nitrogen). In this study ⁵⁷Fe Mössbauer spectroscopy on (Ti, Fe)N model layers is used to obtain direct information about the mechanism of the development and variation of intrinsic stresses in nitridic hard coatings in connection with point defects (e.g. excess N). The results of this investigations are supported by X-ray analysis and Glow Discharge Optical Spectroscopy (GDOS).     

阳极共沉积法制备Fe和Co掺杂PbO2电极及其性能表征

采用阳极共沉积的方法制备了Fe和Co掺杂Ti/PbO2电极。 用XRD、SEM及循环伏安法研究了Fe和Co掺杂对Ti/PbO2电极的影响。 结果表明,掺杂Fe和Co的Ti/PbO2电极与纯Ti/PbO2电极相比,虽然形貌变化很小,但在结构和性质上发生了改变。 Co掺杂可提高电极的析氧活性,PbO2 电极涂层在电化学过程中存在溶解和重新沉积或者晶型转化的现象。 这种Pb2+的溶解与再沉积可能会影响电极材料的寿命。     

纳米PbO/Ti电极催化还原偏硼酸锂制备硼氢化锂

在乙二醇甲醚溶液中电解铅片,制备了铅醇盐配合物,然后将溶液直接水解、凝胶,再通过提拉法涂抹在钛丝表面,450 ℃煅烧2 h制备纳米PbO/Ti电极。 将PbO/Ti电极在0.2~1.0 mol/L LiOH+0.1~0.5 mol/L LiBO2溶液测试催化还原性能,研究了影响电解还原LiBO2制备硼氢化锂(LiBH4)的主要因素,如LiBO2和LiOH浓度等。 通过X射线粉末衍射和扫描电子显微镜对PbO/Ti电极和LiBH4进行了表征。 实验表明,纳米PbO/Ti电极表面颗粒分散较好,修饰电极催化性能稳定,放电电流较大,产率和电流效率分别达15.6%和25.3%。     

Preparation and crystal data of the New Pyrochlores Pb2[M1.5Te0.5]O6.5 (M = Ti,Zr, Sn,Hf)

From mixtures of PbO, MO₂ (M = Ti, Zr, Hf), SnO, and TeO₂, four new oxides Pb₂[M_1.5Te_0.5]O_6.5 have been obtained as yellow powders giving X-ray diffraction patterns characteristic of cubic pyrochlores, S.G. Fd3 m (No. 227), Z = 8, and a/Å values from 10.3529(1) (M = Ti) to 10.7406(1) (M = Zr). The best R factors, from 0.0465 (M = Ti) to 0.0242 (M = Hf), were obtained for Pb in 16(c) positions, M and Te (3:1) randomly distributed in 16(d), oxygen atoms in 48(f) and in a half of the 8(a) sites, and x values for the oxygen positional parameter (origin at center, 3 m) from 0.436 (M = Ti) to 0.421 (M = Zr). For the compounds of Ti and Zr the angles of the coordination polyhedra around the metals are reported. For seven-coordinated Pb^II the stereochemical influence of the nonbonded electron pair is shown. Apparent interatomic distances agree with those calculated.     

Structures and stabilities of small lead oxide clusters PbmOn (m=1-4,n=1-2m)

The structures and stabilities of small lead oxide clusters PbmOn with m=1-4, n=1-2m are systematically studied using density functional theory. It is found that the lowest-energy structures of all these clusters can be obtained by the sequential oxidation of small "core" lead clusters. For Pb-rich clusters (oxygen-to-lead ratio<1), oxygen atoms favor bridge sites for Pb2On and Pb3On and surface sites for Pb4On. The lead-monoxide-like clusters (PbO)i (i=1-4) have great stability because of their significant dissociation energies and highest occupied molecular orbital-lowest unoccupied molecular orbital gaps. This suggests that they could be adopted as the building blocks of cluster-assembled materials. For O-rich clusters (oxygen-to-lead ratio>1), the grouping of oxygen atoms usually appears. It is found that the structures with a grouping of more than two oxygen atoms are unstable.     

新型不锈钢基二氧化铅-碳化钨复合电极材料的研制

在不锈钢基上通过复合电沉积的方式制备了二氧化铅 碳化钨（PbO2-WC）电极。 考察了温度、电流、WC颗粒浓度对电极性能的影响;通过析氧曲线、Tafel曲线、扫描电子显微镜能谱、X射线衍射图谱考察了WC颗粒掺杂前后PbO2电极相关性能的变化。 结果表明,在最佳工艺即温度70 ℃、镀液中WC颗粒浓度为40 g/L时,电流密度为0.015～0.025 A/cm2;PbO2-WC共沉积过程中PbO2发生了择优生长,WC颗粒的加入能够细化PbO2晶粒,使镀层变得致密,相对于PbO2电极,PbO2-WC复合电极的耐腐蚀性上升,析氧过电位下降。