Ti/RuO2-IrO2-SnO2-Sb2O5阳极在农村饮用水消毒中的应用

采用热分解法制备了一种新型高效析氯阳极Ti/RuO₂-IrO₂-SnO₂-Sb₂O₅,将其应用于农村饮用水消毒频繁停开、低电解液浓度的特殊工况下,并与Ti/RuO₂-SnO₂-Sb₂O₅、Ti/RuO₂-TiO₂、Ti/RuO₂-TiO₂-IrO₂三种析氯阳极进行性能对比。通过SEM、EDS、XRD等方法表征测试阳极表面形貌、元素及组成,考察了氯化钠浓度、电流密度、停开频率对阳极析氯效果和寿命的影响。研究发现,Ti/RuO₂-IrO₂-SnO₂-Sb₂O₅阳极活性强、稳定性高;阳极涂层各组分高度融合为固溶体,结构致密,稳定性强;在15 g·L^-1 NaCl、400 A·m^-2电流密度、20℃条件下,Ti/RuO₂-IrO₂-SnO₂-Sb₂O₅阳极电解的电流效率达到91.55%;频繁停开、强化电解条件下寿命达到231 h,是Ti/RuO₂-TiO₂阳极的77倍,预估在400 A·m^-2电流密度下能够使用20年。     

β-PbO2/Sb-SnO2/Ti电极的苯酚电催化性能研究

采用刷涂热解和电镀制得了β-PbO₂/Sb-SnO₂/Ti电极. 采用X射线衍射（X-ray Diffraction,XRD）和扫描电镜（Scanning Electron Microscope,SEM）进行分析与观察,Sb-SnO₂中间层抑制PbF₂的生成,NaF促进二氧化铅晶粒的成型与分散,消除了β-PbO₂聚团. 据谢乐公式（Scherrer）计算晶粒尺寸为25.2 nm,电极表面结晶度高达100%. 极化测试显示,β-PbO₂/Sb-SnO₂/Ti电极扩散段电位区、析氧电位和Tafel斜率分别为1.85 ~ 2.15 V、2.08 V和0.84,优于β-PbO₂/Ti电极的1.40 ~ 1.80 V、1.75 V和0.36. 使用β-PbO₂/Sb-SnO₂/Ti、β-PbO₂/Ti电极在9 mA·cm^-2电流密度对苯酚模拟废水处理240 min,前者COD（Chemical Oxygen Demand）去除率、电流效率（Instant Current Efficiency）高达90.1%和63.28%,优于后者66.9%和44.96%. 寿命测试表明,β-PbO₂/Sb-SnO₂/Ti电极与β-PbO₂/Ti电极相比延长10倍,工业寿命可达8.6a,有较高的工程应用价值.     

Plasma electrolytic synthesis and characterization of pH-sensitive TiO2-ZrO2-ZrTiO4-CeOx films on titanium

Journal of Solid State Electrochemistry - The Ti/TiO2 + ZrO2, Ti/TiO2 + CeOx, and Ti/TiO2 + CeOx + ZrO2 composites, including Y-doped ones, have been...     

Ti/CeO_2-F-PbO_2电极制备及其在有机物降解中的应用

在钛板上制备了氧化铈掺杂的含氟二氧化铅电极(Ti/CeO2-F-PbO2,电沉积法).SEM和XRD分析显示CeO2颗粒能均匀地嵌入二氧化铅镀层中.电化学测试表明,掺杂CeO2提高了二氧化铅的析氧电位(Ti/CeO2-F-PbO2为1.83V,vs.SCE,Ti/F-PbO2为1.78V,vs.SCE).对氯苯酚降解结果表明,Ti/CeO2-F-PbO2电极有较高的COD去除率和电流效率.     

钌-钯掺杂Ti/TiO2阳极电催化降解甲基橙研究

以偶氮染料甲基橙为处理对象, 分别考察了Ru, Pd及Ru-Pd掺杂的Ti/TiO2阳极的光、电催化活性, 并与Ti/RuOx-PdO阳极的电催化活性进行了比较; 利用XPS分析了Ru-Pd掺杂的Ti/TiO2阳极表面Ru, Pd及Ti的化学形态. 实验发现, Ru, Pd及Ru-Pd掺杂的Ti/TiO2阳极的光催化活性都有所降低, 而其电催化活性却都有大幅提升, 特别是Ru-Pd掺杂的Ti/TiO2阳极, 其电催化活性明显地优于Ti/RuOx-PdO阳极. XPS分析表明, Ru-Pd掺杂的Ti/TiO2阳极其光、电催化活性的变化可能与该阳极表面Ru, Pd及Ti的化学形态变化有关.     

EXAFS characterization of Ti/Al2O3 supports and Co/Ti/Al2O3 catalysts

The structure of Ti/Al₂O₃ supports (0–14 wt% Ti) and Co/Ti/Al₂O₃ catalysts (3 wt% Co) was examined by EXAFS. The results indicated that the Ti was present primarily as a highly dispersed surface phase. The Ti EXAFS results indicated that the Ti species were octahedrally coordinated. Evidence of Ti—Ti interactions was found for all loadings (2–14 wt% Ti) suggesting that the Ti surface species are present as small clusters of TiO₂.The Co EXAFS results showed evidence for several structurally different Co surface phases as a function of Ti loading. Evidence of a Co species interacting with the Ti surface phase was observed for the 3% Co/2% Ti-3%Co/6%Ti catalysts. At the highest loadings studied, 3%Co/8%Ti and 3%Co/14%Ti, evidence was found for a CoTiO₃-like phase.     

金属修饰Ti_2N MXene吸附分解H_2S的第一性原理计算

通过第一性原理计算研究了Ti_2NO_2 MXene对H_2S的吸附、分解行为. Ti_2NO_2对H_2S气体分子的吸附结果表明,两者之间为弱的物理吸附, Ti_2NO_2无法有效吸附H_2S气体.采用过渡金属(Sc、 V)修饰Ti_2NO_2的研究结果表明,Sc和V可以在Ti_2NO_2表面上稳定存在,不易发生团聚,其最稳定吸附位为N原子上方.进一步研究了Sc、 V修饰的Ti_2NO_2对H_2S气体分子的吸附行为,结果表明金属修饰后其吸附H_2S的能力明显提高.此外还发现, H_2S分子可以在Sc/Ti_2NO_2和V/Ti_2NO_2表面直接解离为HS*和H*,而后HS*中的H原子再与H*进一步结合形成H_2, S原子则与过渡金属成键. HS*在V/Ti_2NO_2表面解离的势垒为1.69 eV,低于在Sc/Ti_2NO_2表面的2.08 eV,表明V/Ti_2NO_2有望成为吸附、分解H_2S气体的理想候选材料.     

Ti, Na与O2反应机理的理论研究

基于MP2/6-311+G(d)水平, 分别对过渡金属Ti和碱金属Na与O2的反应机理进行了研究. 比较了Ti和Na分别以垂直O—O键和沿着O—O键的方向逼近O2, 以及中性体系Ti/Na+O2和带1个负电荷的体系(Ti/Na+O2)-的情况. 详细分析了不同反应路径的结合能和电荷变化的曲线, 预测了最佳反应方式. 结果表明, 垂直接近方式要比水平接近方式更具有优势; 体系带一个负电荷(Ti/Na+O2)-有利于金属与O2的结合. 同时, 计算结果表明在Ti+O2和(Ti+O2)-体系中Ti容易与单态的O2结合; 在中性体系中Na也容易与单态O2结合, 而在(Na+O2)-体系中Na与三态O2的结合更稳定. 在CCSD(T)/6-311++G(3df)//MP2/6-311+G(d)水平下, 计算了Ti+O2和(Ti+O2)-的反应势能面.     

The electronic structure of Ti2 and Ti2(+)

The Ti(2) and Ti(2)(+) molecular systems have been studied through multireference variational and single reference coupled-cluster methods coupled with large basis sets. Potential energy curves have been constructed for 30 (Ti(2)) and 2 (Ti(2)(+)) states and the usual spectroscopic parameters have been extracted. The main feature of the potential curves is the existence of van der Waals minima (Ti(2)) around 7 bohr irrespective of the molecular symmetry, and 4s(2)-4s(1) interactions (Ti(2)(+)) around 6 bohr. Numerous avoided crossings lead to stronger covalent bonds emanating from 4s(1)-4s(1) atomic distributions. The X-state of the neutral species is formally a (3)Δ(g) state with the first excited state lying within 1 kcal/mol. The removal of the symmetry defining e(-) leads to the X(2)Σ(g)(+) state of Ti(2)(+).     

Comparison of electrocatalytic characterization of Ti/Sb-SnO<Subscript>2</Subscript> and Ti/F-PbO<Subscript>2</Subscript> electrodes

Electrocatalytic oxidation is a promising process for degrading toxic and biorefractory organic pollutants in wastewater treatment. Selection of electrode materials is crucial for electrochemical oxidation process. In this study, Ti/F-PbO₂ and Ti/Sb-SnO₂ electrodes were chosen to compare their electrocatalytic characterization, which were prepared by electrodeposition and thermal decomposition method, respectively. The surface morphology and crystal structure of two electrodes were characterized by scanning electron microscopy (SEM) and X-ray diffraction (XRD). The linear polarization curves show that Ti/Sb-SnO₂ electrodes possess higher oxygen evolution overpotential than Ti/F-PbO₂ electrodes. But the stability and corrosion resistance ability of Ti/F-PbO₂ electrode was higher than that of Ti/Sb-SnO₂ electrode. The electrocatalytic activity of Ti/F-PbO₂ and Ti/Sb-SnO₂ electrodes was examined for the electrochemical oxidation of malachite green (MG). The bulk electrolysis shows that the Ti/Sb-SnO₂ electrodes exhibit the higher electrocatalytic activity for the degradation of MG than Ti/F-PbO₂ electrodes, and the degradation process is good fitting for the pseudo-first order reaction. The higher electrocatalytic activity of Ti/Sb-SnO₂ electrodes can be attributed to the higher oxygen evolution overpotential.     

纳米TiO2-Pt修饰电极的制备及其电催化活性

循环伏安;纳米TiO2-Pt修饰电极的制备及其电催化活性     

纳米TiO2-Pt修饰电极的制备及电催化活性

采用电化学合成前驱体直接水解法和电沉积法制备高活性纳米TiO2-Pt修饰电极，并使用扫描电子显微镜(SEM)对电极的表面形貌和结构进行了表征; 通过循环伏安法研究了纳米TiO2-Pt修饰电极在H2SO4溶液中的电化学行为以及对Mn2＋氧化为Mn3＋的电催化活性. 结果表明,纳米TiO2的晶粒大小约30 nm,修饰在纳米TiO2膜表面的Pt微粒呈现单分散状态,平均粒径约60 nm,纳米TiO2-Pt修饰电极的电化学性能优于纯Pt电极,对Mn2＋的电氧化具有高催化活性,非均相无隔膜电解氧化Mn2＋生成Mn3＋平均电流效率可达86％.     

纳米TiO2膜修饰电极上对硝基苯甲酸异相电催化还原

有机电合成具有对环境友好、反应条件温和副产物少等优点并符合“原子经济性”要求，是一种可持续发展的绿色化学方法，已成为化学研究的重要前沿之一．使用媒质作为氧化剂和还原剂的间接电合成，大多为均相氧化还原电催化过程，把氧化还原催化剂固定在电极表面的异相电催化与均相催化相比具有更为显著的优点．本文采用循环伏安和电解合成法研究了纳米TiO2膜电极在硫酸介质和氢氧化钠介质中的氧化还原行为以及异相电催化还原对硝基苯甲酸的活性，探讨了纳米TiO2膜异相电催化的本质．     

Ti/nanoTiO_2-Pt阳极和Ti/nanoTiO_2阴极成对电合成葡萄糖酸锌和丁二酸

使用新颖的纳米结构电极成对电合成葡萄糖酸锌和丁二酸.采用溶胶-凝胶法制备Ti基纳米TiO2(Ti/nanoTiO2)电极,同时采用电沉积法制备Ti基纳米TiO2-Pt(Ti/nanoTiO2-Pt)修饰电极.通过循环伏安研究发现,Ti/nanoTiO2-Pt电极对葡萄糖氧化及Ti/nanoTiO2电极对马来酸还原均具有高催化活性.以Ti/nanoTiO2-Pt电极为阳极、Ti/nanoTiO2电极为阴极,通过正交实验得到成对电合成葡萄糖酸锌和丁二酸的优化条件为:阳极和阴极电流密度分别为1.2A·dm-2和3.0A·dm-2,阳极液为0.4mol·L-1葡萄糖+0.6mol·L-1NaBr,阴极液为0.6mol·L-1马来酸+0.2mol·L-1NaCl,温度50℃.成对电合成的总电流效率达到170%.     

葡萄糖在Ti/NanoTiO2-ZrO2修饰电极上电催化氧化

在无水乙醇和乙酰丙酮混合溶液中,电解Ti金属制得前驱体Ti(OCH2CH3)4-y(acac)y,再加入ZrCl4,将上述溶液直接水解、干燥后,在450℃煅烧2 h,粉体通过X射线衍射(XRD)分析表明:纳米TiO2-ZrO2粉体呈单分散结构。扫描电子显微镜(SEM)测试表明,颗粒平均尺寸为30~40 nm。通过溶胶-凝胶法制得高活性的Ti/NanoTiO2-ZrO2修饰电极,采用循环伏安研究发现,Ti/NanoTiO2-ZrO2电极对葡萄糖氧化具有高催化活性。在NaBr电解液中,Br-在Ti/NanoTiO2-ZrO2电极表面氧化为Br2,Br2间接电氧化葡萄糖。     

Catalytic Performance of Amorphous Ti/SiO2 in the Gas-Phase Epoxidation of Propylene with H2O2

The epoxidation of propylene with dilute H₂O₂ aqueous solution over titanium silicalite-1 (TS-1) zeolite catalyst is a green chemical reaction for propylene oxide (PO) production. Carrying out the reaction in gas-phase can get rid of problems caused by using methanol solvent. This paper reports an attempt of using non-zeolite catalyst for the gas-phase epoxidation. Amorphous Ti/SiO₂, obtained by grafting amorphous SiO₂ with TCl₄ in ethanol solvent in a chemical liquid-phase deposition (CLD) process, has been used as the catalyst. Results show that the CLD Ti/SiO₂ with appropriate Si/Ti molar ratio is an active catalyst for gas-phase epoxidation, achieving 9.8 % propylene conversion and 66.9 % PO selectivity with 40.3 % H₂O₂ utilization, which indicates that this amorphous Ti/SiO₂ catalyst deserves extensive studies in the future.     

PbO2阳极在硫酸溶液中的析氧失活行为

采用热分解鄄电镀法制备了以Sb 掺杂SnO₂(Sb-SnO₂)为底层的Ti 基PbO₂阳极(Ti/PbO₂). 采用加速电解寿命测试、电化学阻抗谱、XRD、SEM-EDX 等技术, 研究了Ti/PbO₂阳极在硫酸溶液中的电解失效行为和机制.结果表明,在新制备的PbO₂镀层中, 由于氧空位的存在, PbO₂镀层的内应力表现为拉应力, 随着电解的进行, 阳极表面生成的活性氧原子在向基底扩散的过程中, 将Pb³⁺态氧化为Pb⁴⁺态, 逐渐占据镀层内作为自由电子施主的氧空位, 这不仅导致镀层的导电性能下降, 同时使镀层的应力逐渐由拉应力转变为压应力, 镀层性质逐渐劣化. 这一过程基本结束时,活性氧原子才大量扩散至Ti基底导致基底的钝化, 在Ti 基底和镀层界面出现显著的界面应力, 在界面应力和镀层内压应力的共同作用下, 阳极出现鼓泡、脱落, 迅速进入失活阶段.     

Ti表面修饰纳米TiO2膜电极的电催化活性

用电化学合成法在Ti表面修饰一层纳米TiO₂膜,TEM和XRD测试表明晶型为锐钛矿型,晶粒平均尺寸为25nm.用循环伏安法、循环方波伏安法和电解合成法研究了纳米TiO₂膜电极在硫酸介质中的氧化还原行为以及对硝基苯还原的电催化活性。结果表明,纳米TiO₂膜电极具有异相氧化还原催化行为,膜中的Ti(Ⅳ)/Ti(Ⅲ)作为媒质间接电还原硝基苯为对氨基苯酚,收率和电流效率分别达91.6%和95.2%.     

Synthetic architectures of TiO2/H2Ti5O11.H2O, ZnO/H2Ti5O11.H2O, ZnO/TiO2/H2Ti5O11.H2O, and ZnO/TiO2 nanocomposites

Although synthetic investigations of inorganic nanomaterials had been carried out extensively over the past decade, few of them have been devoted to fabrication of complex nanostructures that comprise multicomponents/phases (i.e., composite nanobuilding blocks), especially in the area of structural/morphological architecture. In this work, nanobelts of a protonated pentatitanate (H(2)Ti(5)O(11).H(2)O) were synthesized hydrothermally for the first time. Two technologically important transition-metal-oxides TiO(2) and ZnO were then grown respectively or sequentially onto the surface of the as-prepared nanobelts in aqueous mediums. With a main emphasis on organizational manipulation, the present investigation examines general issues of morphological complexity, synthetic interconvertibility, and material combinability related to fabrication of inorganic nanocomposites. Using this model material system, we demonstrate that complex binary and tertiary composite building blocks of TiO(2)/H(2)Ti(5)O(11).H(2)O, ZnO/H(2)Ti(5)O(11).H(2)O, ZnO/TiO(2)/H(2)Ti(5)O(11).H(2)O, and ZnO/TiO(2) can be architected stepwise in solution. Structural features of these nanocomposites have also been addressed.     

刷涂热分解法制备Ti/SnO2-Sb2O5阳极及其性能

通过刷涂热分解法制备了锑掺杂的钛基二氧化锡(Ti/SnO2-Sb2O5)涂层电极. 在酸性介质中, 用扫描电镜(SEM)、X射线衍射仪(XRD)、循环伏安和快速寿命测试等方法研究了Ti/SnO2-Sb2O5电极制备条件、电极结构、性能和寿命. 结果表明, Ti/SnO2-Sb2O5电极涂层具有“干泥”结构, 用锡锑摩尔比为9:1的涂液组成、在550 ℃烧结温度下制备的Ti/SnO2-Sb2O5的电极涂层平整致密,龟裂小, 电极孔隙率小, 稳定性最好.