In this study, the effect of pectin extraction method on the properties of cellulose nanofibers (CNFs) isolated from sugar beet pulp (SBP) was studied. Pectin was extracted by the industrially practiced method by sulfuric acid hydrolysis or by enzymatic hydrolysis using a cellulase/xylanase enzymes mixture. The CNFs were then isolated by high-pressure homogenization and investigated in terms of their chemical composition, crystallinity, size, degree of polymerization, and re-dispersion in water after freeze-drying. The mechanical properties and surface characteristics of CNF films were also studied. The results showed that fibrillation of the de-pectinated SBP was more efficient for the acid hydrolyzed SBP. CNFs from the acid-hydrolyzed SBP had a slightly wider diameter, higher crystallinity, viscosity, and α-cellulose content but a lower degree of polymerization than CNFs from the enzyme-hydrolyzed SBP. Owing to the presence of more residual hemicelluloses in the CNFs from the enzyme-hydrolyzed SBP, the CNFs had higher re-dispersion ability in water. CNF films from enzyme-hydrolyzed SBP displayed slightly better mechanical properties and higher water contact angle than acid-hydrolyzed CNF films.
Graphic abstractEucalyptus cellulose is usually pre-treated by oxidation with 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO), NaBr and NaClO at pH 10.5 and 25 °C before the mechanical process required to obtain cellulose nanofibers (CNFs). In this study, different aspects to improve the effectiveness and sustainability of the TEMPO-mediated oxidation are analyzed. The optimization was carried out at different reaction times by modifying both the concentration of the NaClO and the amount of the catalysts (TEMPO and NaBr). Results show that the carboxyl groups increased up to 1.1 mmol/g with 5 mmol NaClO/g after 50 min, and that the catalyst concentration can be reduced to 0.025 mmol TEMPO/g and 0.5 mmol NaBr/g to minimize costs while maintaining the high fibrillation degree of the CNFs. The kinetic of the reaction can be considered as zero-order with respect to NaClO, and as first order with respect to cellulose. As a result of this work, the catalyst doses are reduced up to 75% compared to the most widely used catalyst doses (0.1 mmol/g TEMPO and 1 mmol/g NaBr), obtaining highly fibrillated CNFs with a lower environmental impact. This reduction of catalyst doses will reduce the costs and facilitate the implementation of CNF production at industrial scale.
Graphical abstractCellulose-based triboelectric nanogenerators (TENGs) can provide power for various monitoring devices and are environmentally friendly and sustainable. Chemical functional modification is a common method to improve the electrical output performance of cellulose-based TENGs. In this work, an environmentally friendly high-performance triboelectric nanogenerator based on a polydopamine/cellulose nanofibril (PDA/CNF) composite membrane and fluorinated ethylene propylene was developed. Dopamine generates polydopamine nanoparticles through oxidative self-polymerization and adheres to the surface of nanofibers. The synergistic effect of amino group introduction and membrane surface microstructure effectively enhanced the output performance of TENGs to a certain extent. The effects of PDA content, CNF composite film thickness and different working conditions on the electrical output were systematically investigated. The optimized PDA/CNF-TENGs exhibited an enhanced electrical output performance with voltage, current, and power density values of ≈205 V, ≈20 µA, and ≈48.75 μW·cm?2, respectively. The PDA/CNF-TENGs exhibited stable and identifiable signals when used as a self-powered sensor for human motion monitoring, showing the potential prospects of cellulose materials for TENGS and other electronic applications.
Graphical abstractInspired by mussels, a new cellulose-based (CTP) adhesive was fabricated by simply blending via cellulose nanofibrils (CNFs), tannic acid (TA), and polyethyleneimine (PEI), where the preparation method was green, facile, and simple. The structure and properties were examined by FT-IR, TGA, XRD, SEM, lap shear tensile, and water absorption tests. The results showed that chemical bonds, hydrogen bonds, and chain entanglement were formed among CNFs, TA, and PEI. Compared with the CNF adhesive, the dry shear strength of the CTP adhesive increased 103% to 392.2?±?32.2 kPa. And the wet shear strength of CTP adhesive increased from 0 kPa to 144.7?±?20.1 kPa, indicating that the CTP adhesive can be used in humid or even water environments. Meanwhile, the water absorption of CTP adhesive decreased from 37.9?±?14.1% to 12.8?±?5.9%. It was the introduction of catechol groups and physical–chemical interactions of three components that endow the CTP adhesive with improved dry and wet adhesion strength and water resistance. Moreover, the proposed CTP adhesive could be used on the surface of various materials, including rubber, plastic, paper, wood, metal, and glass. Overall, this work shows that the CTP adhesive has a wide range of application prospects.
Graphical abstractThe dry pulp direct kneading method is an industrially viable, low-energy process for manufacturing cellulose nanofiber (CNF)-reinforced polymer composites, where the chemically modified pulps are nanofibrillated and uniformly dispersed in the polymer matrix during melt compounding. In the present study, cellulose fibers of various sizes ranging from surface-fibrillated pulps (20 μm in width) to fine CNFs (20 nm in width) were prepared from softwood bleached kraft pulps using a refiner and a high-pressure homogenizer. These cellulose fibers were modified with alkenyl succinic anhydride and dried. The dried fibers were used as a feed material for melt compounding in the dry pulp direct kneading method to fabricate CNF-reinforced high-density polyethylene (HDPE). When surface-fibrillated pulps were employed as a feed material, the pulps were nanofibrillated and dispersed uniformly in the HDPE matrix during melt compounding. The resulting composites had much better properties—i.e., much higher tensile modulus and strength values, and much lower coefficient of thermal expansion values—than the composites produced using pulps without pre-fibrillation. However, when CNFs were used as a feed material, they were shortened and agglomerated during melt compounding, and the properties of the composites consequently deteriorated. The study concludes that surface-fibrillated pulp, which can be produced cost-effectively using a refiner on an industrial scale, is more suitable as a feed material than CNFs for melt compounding in the dry pulp direct kneading method. This finding enables the elimination of a preliminary step in the preparation of CNFs from pulps, which is a time-consuming and energy-intensive process.
Graphical abstractCellulose nanofibril (CNF) aerogels have attracted great interests in recent years due to the low cost, sustainability and biocompatibility of raw CNF. However, the poor thermal stability and flammable feature of CNF aerogels have limited their wider applications. In this paper, polydopamine/CNF composite aerogels with good comprehensive properties are fabricated by modification of CNF with polydopamine and metal coordination bonds crosslinking. The microstructure and properties of composite aerogels are thoroughly characterized by a variety of tests. It is found that the microstructure of aerogels are more regular and the compressive strength of aerogels are enhanced by the incorporation of polydopamine and Fe3+ crosslinking. Importantly, the thermal stability and flame resistance of aerogels are significantly improved, which permit the application of composite aerogels in high-temperature thermal insulation. In addition, the reversible characteristic of metal coordination bonds allows the water induced healing of fractured composite aerogels. This study is expected to provide information for future development of green and high-performance aerogels.
Graphic abstractAn integrated aero-cryogel (A-CG) monolith with hierarchical porous structure was developed by inter-crosslinking of cellulose nanofiber/polylactic acid nanocomposite aerogel and carboxymethyl cellulose (CMC) cryogel (CG). The photothermal nanoparticles-enriched CMC CG phase served as a sunlight absorbing layer, exhibiting a broadband sunlight absorption of 98%. Due to the large amount of weakly bounded water molecules, the swelled CMC CG possessed a lower evaporation enthalpy than that of pure water, which facilitates water evaporation, while the nanocomposite aerogel phase acted as an excellent thermal insulator and afforded highly efficient water transport channels. Thus, the developed A-CG monolith supported by insulated polystyrene foam to protrude above the water surface, could reach an evaporation rate of 2.16 kg m?2 h?1 under an irradiation of 1 Sun (100 mw/cm2) with an efficiency of 93.6%. More remarkably, when the wind energy was imparted, an evaporation rate of 5.67 kg m?2 h?1 was achieved at a wind speed of 3 m s?1. The high-efficiency purification outcomes of various raw water demonstrate the great potentials of A-CG material in solar vapor generation.
Graphical abstractOceans and soils have been contaminated with traditional plastic due to its lack of degradability. Therefore, green biopolymer composites reinforced with cellulose nanocrystal-zinc oxide hybrids (ZnO hybrids) with good biodegradation ability provided a positive impact on reducing environmental challenges. In this work, the effect of various morphologies of ZnO hybrids on the biodegradation ability of poly(butylene adipate-co-terephthalate), PBAT) under seawater, soil burial, and UV aging conditions were investigated. Sheet-like ZnO hybrids (s-ZnO hybrid) efficiently enhanced the mechanical, UV-blocking properties and biodegradation ability of PBAT nanocomposite films. Compared to neat PBAT, the best tensile strength of PBAT nanocomposite with 2 wt% s-ZnO hybrid was increased by 15.1%, meanwhile this nanocomposite films showed the highest biodegradation rate after 80 days of soil degradation and 90 days of seawater degradation. Besides, three possible biodegradation mechanisms of green PBAT nanocomposite films were presented, hinting that such PBAT nanocomposite have great promising packaging applications.
Graphic abstractHerein, cellulose nanofibrils (CNF), alkali lignin (AL), and montmorillonite (MMT) were used to produce reinforced polyvinyl alcohol (PVA) hydrogels. The effects of MMT and AL contents on the rheological properties of reinforced hydrogel were studied. Compared with PVA/CNF hydrogel, the storage modulus of 40 wt% MMT-reinforced PVA hydrogel was increased by 41.4%. The rheological properties of MMT-enhanced PVA hydrogel could be adjusted by the variation of MMT loading. Also, as the PVA matrix had a synergistic effect with the embedded MMT and AL, the composite hydrogel demonstrated high efficiency in the removal of methylene blue dye (MB) from wastewater. Adsorption tests conducted at various time intervals (60–360 min) show that the hydrogels containing same content of MMT had higher removal efficiency. The MB adsorption of PVA/2CNF-0Li-40MMT was over 98.0%, whereas its adsorption equilibrium time and maximum adsorption capacity (qm) were 360 min and 67.2 mg/g, respectively. However, an extremely high content of MMT reduced the MB adsorption rate.
Graphic abstractThis study prepared a waterproof cellulose nanofibril (CNF) sheet via the deposition of an alkyl ketene dimer (AKD) on the sheet’s controlled porous structure. The porosity of the CNF sheet was controlled by drying under different conditions, which included hot-press drying (HD) and solvent-exchange drying (SD), and the effect on the hydrophobization and water-related barrier performance of the sheet were investigated. When the SD sheet was immersed in an AKD wax solution, the sheet exhibited super-hydrophobicity and a lower water vapor transmission rate, compared with the HD sheet. This indicated that the porous structure of the SD sheet enabled AKD to be adsorbed on both the surface and the inner surface and it filled in the pores of the sheet, thereby giving rise to excellent waterproofing properties. The performance of a hydrophobized SD sheet as a water barrier material was comparable to a linear low-density polyethylene film. This study confirms the possibility for AKD wax to be immersed in a porous CNF sheet and used as a potential barrier material in hydrogel packaging.
Graphical abstractVulcanized fibers are all-cellulose materials made from cotton and/or wood cellulose after aqueous zinc chloride treatment. These materials were invented in the UK in the mid-nineteenth century and is widely used because of their excellent characteristics, such as impact resistance and electrical insulation. Recently the matured vulcanized fibers have been recognized as renewable and biodegradable materials and reevaluated with advanced cellulose technologies derived from cellulose nanofibers (CNFs) and all-cellulose composites. The microscopic analysis based on the improved freeze-drying method revealed that the strength of vulcanized fiber sheets can be attributed to the chemically defibrillated CNFs. The architecture is similar to all-cellulose composites made from the same raw materials in which the residual cellulose fibers serve as reinforcement, and the CNFs serve as adhesives or matrix components. In this report, we describe the history and structural characteristics of vulcanized fibers and introduce a new aspect in aqueous zinc chloride treatment of cellulose.
Graphical abstractThis study introduces an effective route to fabricate chitosan (CS)-based film. The films were prepared through cross-linking reaction between CS and hydroxyethyl cellulose (HEC) using epichlorohydrin (ECH) as the cross-linker and simultaneously in-situ loading with CuO nanoparticles. FT-IR and loading efficiency results indicated the occurrence of inter- and intra-molecular cross-linking reaction between CS and HEC. XRD and EDS analyses showed that the CuO nanoparticles were evenly deposited onto CS film matrixes. SEM characterization showed that the films were of compact, dense and uniform cross morphologies, as well as obvious voids. The films also exhibited desired swelling ratio and water vapor permeability. The enhanced tensile strength was obtained with a maximum value of 77.02?±?3.26 MPa, while the stretch-ability slightly decreased. The thermal stability of the films decreased after cross-linking with HEC. The antibacterial ability of the films was generally improved with the increase of HEC and ECH contents.
Graphical abstractPreparation and properties of epichlorohydrin-cross-linked chitosan/hydroxyethyl cellulose based CuO nanocomposite films
Clay adsorbents are considered an inexpensive and readily available solution for removing heavy metals, including cadmium, from the environment to reduce pollution. In this study, thiol-modified bentonite (SH-Bent) was prepared by grafting cysteamine hydrochloride onto natural bentonite (Bent). The effects of pH, equilibrium contact time, and temperature on the adsorption–desorption behavior of Cd2+ were studied, and adsorption isotherm models were applied to examine the adsorption behavior of SH-bent. SH-Bent demonstrated better performance and stability for Cd2+ adsorption than Bent. SH-Bent exhibited an enhanced adsorption capacity for Cd2+ at equilibrium of 49.3 mg/g at pH 6, 120 min, and 303 K, which was 42-fold higher than that of Bent under the same conditions. An investigation of the desorption behavior of Cd2+ adsorbed on Bent and SH-Bent in simulated acid rain revealed that SH-Bent has high stability, with a desorption rate of 5.73% at pH 4.5, 60 min, and 303 K, which was much lower than that demonstrated by Bent under the same conditions (45.68%). The Langmuir equation was the best-fitted adsorption isotherm model, closely followed by the Freundlich, Tempkin, and Dubinin–Radushkevich models. A significant difference in diffusion was observed between the two types of clay according to the intraparticle diffusion model. The adsorption–desorption processes of SH-Bent and Bent fit the pseudo-second-order model best among the five kinetic models examined. The information provided in this study can be used to apply thiol-modified clay for wastewater treatment or for the removal of cadmium from soil.
Graphical abstractFabricating mechanically strong hydrogels that can withstand the conditions in internal tissues is a challenging task. We have designed hydrogels based on multicomponent systems by combining chitosan, starch/cellulose, PVA, and PEDOT:PSS via one-pot synthesis. The starch-based hydrogels were homogeneous, while the cellulose-based hydrogels showed the presence of cellulose micro- and nanofibers. The cellulose-based hydrogels demonstrated a swelling ratio between 121 and 156%, while the starch-based hydrogels showed higher values, from 234 to 280%. Tensile tests indicated that the presence of starch in the hydrogels provided high flexibility (strain at break?>?300%), while combination with cellulose led to the formation of stiffer hydrogels (elastic moduli 3.9–6.6 MPa). The ultimate tensile strength for both types of hydrogels was similar (2.8–3.9 MPa). The adhesion and growth of human osteoblast-like SAOS-2 cells was higher on hydrogels with cellulose than on hydrogels with starch, and was higher on hydrogels with PEDOT:PSS than on hydrogels without this polymer. The metabolic activity of cells cultivated for 3 days in the hydrogel infusions indicated that no acutely toxic compounds were released. This is promising for further possible applications of these hydrogels in tissue engineering or in wound dressings.
Graphical abstractCaesalpinia sappan L. wood fiber (CSWF), a novel advanced bio-reinforcement for polybutylene succinate (PBS) composite films, has shown significant promise ranging from 0 to 15 part per hundred of resin (phr). The functional groups and interactions, morphology, thermal stability, mechanical characteristics, and biodegradability were all investigated. Without treatment or any compatibilizers, CSWF could be well-dispersed in the PBS matrix. The PBS/CSWF10 composite film had highest mechanical strength, with a tensile strength of 12.21 N/mm2 and a break elongation of 21.01%. Biodegradability studies indicated that the PBS/CSWF10 composite films degraded completely in three months. Furthermore, the Ea of degradation resulting from TGA and the shift of wavenumber resulting from FTIR revealed that the addition of CSWF has a greater interaction between additive and martix than conventional cellulose. The PBS/CSWF10 composite has the potential to be environmentally friendly, with promising short-term degradation and rising mechanical characteristics. Therefore, it is the optimum concentration of a certain biocomposite film. As a result, a novel advanced natural-based cellulose for biopolymer composites film was discovered, as well as other benefits for bio-reinforcement of the green plastic composite film industry.
Graphical abstractUniformly-sized porous cellulose beads functionalized with amidoxime groups were prepared for the first time using a microfluidic method with N-methylmorpholine N-oxide (NMMO) monohydrate as a cellulose solvent. The molten state cellulose dope in NMMO monohydrate (cell/NMMO dope) as a disperse phase and hot mineral oil as a continuous phase were used in a T-junction microfluidic chip to produce uniformly-sized cell/NMMO droplets. Coagulation of the molten state cell/NMMO droplet at high temperature and amidoxime functionalization could prepare the highly-porous spherical amidoxime-functionalized cellulose beads with a uniform fibrous open internal structure. The prepared amidoxime-functionalized cellulose beads showed excellent metal adsorption properties with a maximum adsorption capacity of?~?80 mg g?1 in the case of Cu2+/phthalate ions. The newly developed highly-porous cellulose beads can open many new applications with other proper functionalization at the reactive hydroxyl groups of the cellulose.
Graphic abstractThe development of eco-friendly corrosion inhibitors is a subject of several investigations, especially natural polymers. Aimed at suppressing the corrosion of L80 steel in 1 mol/L hydrochloric acid (HCl), a novel natural polymer inhibitor was developed based on xanthan gum (XG) and β-Cyclodextrin (β-CD) in this work. The corrosion inhibition effect of β-cyclodextrin modified xanthan gum (β-CD-XG) on L80 steel was evaluated by electrochemical methods, and surface analysis technology. Adsorption isotherm studies, Fourier transform infrared spectroscopy (FT-IR), and X-ray photoelectron spectroscopy (XPS) were used to explore the corrosion inhibition mechanism of β-CD-XG on L80 steel. The results suggested that β-CD-XG was classified as a mixed-type inhibitor, and mainly suppressed the anode metal dissolution by a tight adsorption film. The formation of the film was attributed to the chemisorption of –OH, –COO-, –CH2–O–, and –CH2–O–CH2– groups on the surface of L80 steel, which conformed to the Langmuir adsorption model. The experimental results illustrated that the maximum corrosion inhibition efficiency of 94.74% was acquired at 200 mg/L β-CD-XG at 293 K.
Graphic abstractIncreasing electromagnetic pollution calls for electromagnetic interference (EMI) shielding materials, especially sustainable, lightweight, and environmentally stable, biomass-based materials. MXene-coated wood (M/wood) is prepared by simply spraying MXene sheets on the wood surface. Varying this spray coating manipulates the shielding performance and its application to different wood species. The M/wood exhibits high electrical conductivity (sheet resistance is only 0.65 Ω/sq) with an excellent EMI shielding effectiveness of 31.1 dB at 8.2?~?12.4 GHz and is also fire retardant. Furthermore, waterborne acrylic resin (WA) is coated on M/wood to enhance environmental stability. The WA coating improves EMI shielding performance stability after water-soaking and drying testing and prevents the peeling of MXene from wood. These satisfactory properties of WA-M/wood and the facile manufacturing approach promote the feasibility of wood-based EMI shielding materials.
Graphical abstractNowadays, freshwater shortage, energy crisis and environmental pollution are the three major threats to human beings. Bio-waste is an important source of environmental pollutant emissions and a renewable resource with great potential. Herein, we develop a photothermal material based on bagasse for solar steam generation to relieve the freshwater crisis and mitigate environmental pollution caused by bio-waste. The mainly functional part of the solar-driven steam generator here is bagasse-based photothermal aerogel (B-PTA), which composes of carbonized bagasse (CB) and bagasse-derived cellulose fiber (BDCF). The B-PTA relying on CB can effectively absorb sunlight (~?95%), resulting in a prominent light-to-heat ability. The B-PTA with DBCF has super-hydrophilicity, water transport and retention ability. Depending on the excellent light absorption and 3D water passageway, the B-PTA gives a water evaporation rate of 1.36 kg m–2 h–1, and achieves a photothermal conversion efficiency of 77.34% under 1-sun illumination (1 kW m–2). The B-PTA shows remarkable stability that the efficiency without significant change after 20 cycles. In addition, the B-PTA can effectively desalt seawater and purify dye wastewater with natural sunlight. Therefore, turning bio-waste into valuable photothermal material for solar steam generation is possible. Due to the merits of low cost, scalability, environmental friendliness, B-PTA has the potential for real-world water purification.
Graphical abstractMultifunctional materials for water purification have attracted significant attention due to the increased water pollution problems. However, fabricating the low-cost, effective, and recyclable separation material for wastewater containing various hazardous substances is still a challenge. Herein, we developed an Ag/TiO2@PDMS coated cotton fabric with self-cleaning ability, high flux, superior visible-light photocatalytic ability, and recyclability via the “powder?+?glue” strategy. The composites are superhydrophobic (water contact angle 157°) and show high separation efficiency. After 20 times of repeated use, the separation efficiency remains 16,322 Lm?2 h?1, and methylene blue (MB) 's degradation rate remains almost unchanged. The high oil purification, catalytic property, excellent stability in harsh conditions, and recyclability enable the material as a satisfactory candidate for water purification.
Graphical abstract