ZnO：V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO:V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO:V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO:V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

ZnO∶V薄膜后退火处理前后的微结构与发光特性

利用溶胶-凝胶(Sol-gel)法在单晶硅(100)衬底上分别制备了ZnO∶V薄膜和纯ZnO薄膜。为进一步研究后退火对ZnO∶V薄膜结构和发光性质的影响,在两段式快速退火后又在800℃下进行了后退火处理。X射线衍射的结果表明:后退火处理前,钒(V)的掺入使ZnO结晶质量变差,而800℃退火处理后,从ZnO的衍射峰中可以看出,相对于无V杂样品其结晶质量变好。扫描电子显微镜形貌图中可以看出制备的样品薄膜颗粒大小均匀,薄膜致密度较高。光致发光(PL)谱的研究表明:ZnO∶V薄膜在800℃退火处理后,紫外和绿带发光峰均增强,但紫外发光峰增强得更多;与同样条件下制备的纯ZnO薄膜的PL谱比较,发现V掺杂后样品的紫外激子复合发光峰的强度明显增强且峰位发生蓝移,而缺陷引起的绿带发光峰的强度降低。     

氮气氛中高温退火对ZnO薄膜发光性质的影响

以二乙基锌和水汽分别作为锌源和氧源,用LP-MOCVD方法在p型Si(100)衬底上生长了单一取向的ZnO薄膜。对得到的样品在氮气气氛中进行高温热处理,退火温度分别为900,1000,1100℃。利用室温PL谱、XRD、AFM、XPS等方法对样品的性质进行了研究。研究表明:(1)随着退火温度的升高,样品的结晶性质也逐渐提高,从表面形貌观察到晶粒尺寸逐渐增大;(2)当退火温度从900℃升高至1000℃时,样品的光致发光谱中可见光波段的发光强度有所减弱,而紫外波段的发光强度明显增强;当退火温度升高至1100℃时,可见光波段的发光几乎完全被抑制,而紫外波段的发光强度急剧增强。分析认为,高温退火改善晶体结晶质量的同时调制了样品的Zn/O比,氮气气氛下的热处理使得样品内的氧原子逸出,来自受主缺陷OZn的可见发射随温度升高逐渐减弱,而当退火温度达到1000℃以上时样品成为富锌状态,此时与施主缺陷Zni有关的紫外发射急剧增强。     

ZnO:Al/p-Si的接触特性

利用射频磁控溅射制备了ZnO：Al／p—Si接触,并对其进行C-V和I-V特性的77～350K变温测量。并对未热退火和800℃热退火两种样品的测量结果进行了对比分析。结果发现,未经热退火和经过热退火处理的样品在C—V和I-V特性上有很大差别。解释了两种样品的C—V和I-V测量结果的不同。对于未退火的样品,由于界面处的大量界面态的屏蔽作用,使得ZnO：Al／p—Si异质结的C—V曲线发生畸变。经800℃热退火,ZnO：Al／p—Si异质结的C—V特性恢复正常,说明热退火已经消除了异质结中的界面态和缺陷态。研究表明ZnO：Al／p—Si异质结经适当热退火处理有更好的整流特性同时对光致发光也更有利。     

退火温度对ZnO薄膜结构和发光特性的影响

采用反应射频磁控溅射法在 Si(100)基片上制备了高c轴择优取向的ZnO薄膜，研究了退火温度对ZnO薄膜的晶粒尺度、应力状态、成分和发光光谱的影响，探讨了ZnO薄膜的紫外发光光谱和可见发光光谱与薄膜的微观状态之间的关系.研究结果显示,在600—1000℃退火温度范围内，退火对薄膜的织构取向的影响较小，但薄膜的应力状态和成分有比较明显的变化.室温下光致发光光谱分析发现，薄膜的近紫外光谱特征与薄膜的晶粒尺度和缺陷状态之间存在着明显的对应关系；而近紫外光谱随退火温度升高所呈现的整体峰位红移是各激子峰相对比例变 关键词： ZnO薄膜 退火 光致发光 射频反应磁控溅射 可见光发射     

退火对常压MOCVD法生长的高结晶性能 ZnO薄膜发光特性的影响

研究了氧气退火和氮气退火对ZnO薄膜发光特性的影响。ZnO膜是采用常压金属有机化学气相沉积（MOCVD）法在蓝宝石（0001）衬底上生长的。原生样品1有一很强的紫外峰及较强的绿光峰（525nm附近）;原生样品2有很强的紫外峰,深能级发光几乎观察不到。然后从不同原生膜上取两块小样品,分别在氧气和氮气中退火,退火温度是400,500,600,700,800℃。结果表明,在700℃以下退火,退火气氛对ZnO膜的深能级发光影响较大;超过700℃后,退火温度对ZnO薄膜的发光影响大,但退火气氛影响不太明显。通过退火对ZnO薄膜发光特性的影响,讨论了ZnO膜中525nm附近绿光峰的起源。     

ZnO-Si不同退火条件对生长ZnSe薄膜的影响

研究了作为缓冲层的ZnO薄膜在不同的退火时间、退火温度下退火对Si衬底上生长ZnSe膜质量的影响。当溅射有ZnO膜的Si(111)衬底的退火条件变化时，从X射线衍射谱（XRD）和光致发光谱（PL）中可见，ZnSe(111)膜的晶体质量有较大的变化。变温的PL谱表明，Si衬底上生长的具有ZnO缓冲层的ZnSe膜的近带边发射峰起源于自由激子发射。     

退火温度及退火气氛对ZnO薄膜的结构及发光性能的影响(英文)

采用脉冲激光沉积技术在Si/蓝宝石衬底上制备了ZnO薄膜,结合快速退火设备研究了不同退火温度(500~900℃)及退火气氛(N2,O2)对薄膜的结构及其发光性能的影响。并优化条件得到具有最小半峰全宽及最大晶粒尺寸的薄膜。X射线衍射(XRD)结果表明:氮气氛下退火的ZnO薄膜最佳退火温度为900℃;氧气氛下退火的ZnO薄膜最佳退火温度为800℃。红外(IR)光谱中,退火后Zn-O特征振动峰红移,说明在退火过程中,原子重新排布后占据较低能量位置;同样的退火温度下,氮气氛下退火的薄膜质量更优。同步辐射光电子能谱(synchrotron-based XPS)分别表征了未退火及N2,O2下900℃退火的ZnO薄膜,分峰拟合结果表明氧气氛下退火产生更多的氧空位。结构表征结合光致发光(PL)谱表明绿光的发光峰与氧空位有关。     

退火及超声处理对ZnO薄膜结构和发光特性的影响

 利用对向靶射频磁控溅射系统在Si（100）衬底上制备了ZnO薄膜，并对其进行了退火和超声处理。采用XRD,AFM和光致发光谱对其结构、表面形貌和性能进行了分析。结果表明：沉积态ZnO薄膜（002）择优取向稍差,尺寸较小,表面粗糙度较大。随退火温度的升高，颗粒粒径增大，样品的取向性和结晶度都明显变好，应力状态由压应力转变为张应力,粗糙度降低。超声处理缓解了薄膜中的张应力，晶粒尺寸更趋增大;用波长为280 nm的激发光激发薄膜时，沉积态薄膜无发光峰存在;随着退火温度升高，出现了一个378 nm的紫外峰和一个398 nm的紫峰;紫外峰峰值强度随退火温度升高不断增强，而紫峰的峰位随退火温度升高基本不发生变化，峰值强度增强;700 ℃退火后的薄膜经超声处理后，发光谱中出现了峰值波长为519 nm的绿色发光带。     

超声处理对ZnO薄膜光致发光特性的影响

对于结晶状态好的ZnO薄膜，测量了其光致发光(PL)光谱，发射光谱中只发现了峰值波长约389 nm的近紫外光.样品进行超声处理后，发射谱中不仅观察到近紫外峰，又观察到波长约508 nm的绿光峰.绿光峰的强度比近紫外光的强度强得多，且近紫外峰红移.进一步的热处理使绿光峰大大增强.超声处理改变了ZnO薄膜的质量和结晶状态，使晶格中产生氧空位.处理过程中的热效应使得薄膜晶格振动加剧.当晶格振动加剧到一定程度，晶格中的氧脱离格点形成氧空位.510 nm左右的绿色发光峰是ZnO晶体中的氧空位产生的.薄膜的温度越高， 关键词： ZnO薄膜 超声 光致发光     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Improvement of four-wave mixing-based wavelength conversion efficiency in dispersion shifted fiber by 40-GHz clock pumping

40-GHz clock modulated signal as a pump to improve the efficiency of four-wave mixing (FWM)-based wavelength conversion in a 26.5-km dispersion shifted fiber (DSF) is investigated. The experimental results demonstrate that the conjugated FWM component has higher intensity with the clock pumping than that with the continuous-wave (CW) light pumping. The improvement of FWM-based wavelength conversion efficiency is negligible when the pump power is less than Brillouin threshold. But when the pump power is greater than Brillouin threshold, the improvement becomes significant and increases with the increment of pump power. The improvement can increase up to 9 dB if pump power reaches 17 dBm.     

Characterization of PolyA and PolyC mismatches by Raman spectroscopy

A.C mismatches are studied by Raman spectral characterization of PolyA, PolyC, and their equimolar complex in solution of 0.14 mol/L Na ,pH7.0.Experimental results show that A·C mismatches occur to be A/B (mainly A) conformers, and unlike Watson-Crick base pairing, this kind of mismatches is stabilized by only one hydrogen bond involving cytosine N4H2 and adenine N7.The formation of A·C complex makes the base stacking interactions much stronger, and conformation of the backbone more ordered, which leads to obvious Raman hypochromic effect with some shifts in corresponding bands.