PtZn-Sn/SBA-15合成、表征及对丙烷催化脱氢性能

以SBA-15为载体,利用浸渍法制备了单、双和三金属Pt催化剂,并对催化剂进行了N2物理吸附(BET)、程序升温还原(H2-TPR)、H2-化学吸附、透射电子显微镜(TEM)和O2-脉冲等技术表征,研究了它们对丙烷催化脱氢(CDH)制丙烯反应的催化性能。研究结果表明,Pt在三金属催化剂中的分散性能最好,并且部分负载组分可以进入SBA-15的孔道,Pt的分散度达到29%,Pt粒子尺寸为3 nm左右。三金属催化剂表现出优越的脱氢性能,这主要归结于载体的弱酸性、活性组分和助剂、载体之间的相互作用及Zn对Pt的电子调控作用。这些因素使催化剂的积炭量较低,因而具有较高的脱氢稳定性和极高的选择性。     

SBA-15负载高分散纳米NiO的丙烷氧化脱氢制丙烯催化性能

采用浸渍法通过改变焙烧气氛制备了系列NiO/SBA-15 (w_NiO=20%)催化剂, 并考察了催化剂的丙烷氧化脱氢(ODHP)反应性能. 实验结果表明, 与在静止和流动空气中焙烧的催化剂相比, 在1%NO/He (V_NO/V_He=1:99)气氛中焙烧的NiO/SBA-15-NO具有优异的低温丙烷氧化脱氢制丙烯性能, 在350 ℃时, 丙烷的转化率和丙烯收率分别约达29%和13%. 反应温度升至450 ℃时, 丙烯的选择性仍保持在45%左右. X射线粉末衍射(XRD)和透射电镜(TEM)测试结果表明, 1%NO/He气氛可有效抑制焙烧过程中NiO纳米颗粒的团聚, 使NiO物种高分散于SBA-15 的孔道中. H₂-程序升温还原(H₂-TPR)和O₂-程序升温脱附(O₂-TPD)测试结果表明, 随着NiO在SBA-15上分散度的提高, 催化剂的抗还原性增强, ODHP活性氧物种O-的含量增加, 进而使1%NO/He气氛中焙烧的NiO/SBA-15-NO在较宽的温度范围内(350-450 ℃)均具有良好的丙烯选择性, 并显著提高了催化剂的低温活性.     

New pi-complexation adsorbents for propane-propylene separation

New adsorbents were prepared and tested for the separation of propane-propylene mixtures by adsorption. The ordered mesoporous material SBA-15 was used as the starting material for silver-ion deposition for pi-complexation with propylene. Two different loadings of silver were evaluated. Adsorption equilibrium and kinetic measurements of propane and propylene in the matrix (pure SBA-15) and the silver-modified adsorbents were performed at 323, 343, and 373 K. In this temperature range, the selectivity of propylene in one of the materials (Ag/SBA-15 = 0.5) is in the range 13-22 because the amount of propane adsorbed is very small, 0.095 mmol/g of propane versus 1.12 mmol/g of propylene at 100 kPa and 343 K. The diffusivity of both hydrocarbons is not seriously affected by the introduction of silver into the mesoporous structure.     

Effect of aluminum modification on catalytic properties of PtSn-based catalysts supported on SBA-15 for propane dehydrogenation

The catalytic properties of PtSn-based catalysts supported on siliceous SBA-15 and Al-modified SBA-15, such as Al-incorporated SBA-15 (AlSBA-15) and alumina-modified SBA-15 (Al2O3/SBA-15), for propane dehydrogenation were investigated. Al2O3/SBA-15 was prepared either by an impregnation method using aluminum nitrate aqueous solution, or by the treatment of SBA-15 with a Al(OC3H7)3 solution in anhydrous toluene. N2-physisorption, FT-IR spectroscopy, solid-state 27Al MAS NMR spectroscopy, hydrogen chemisorption, XRF, NH3 temperature-programmed desorption, X-ray photoelectron spectroscopy and TPO were used to characterize these samples. Among these catalysts, the PtSn-based catalyst supported on Al2O3/SBA-15, which was grafted with Al(OC3H7)3, exhibited the best catalytic performance in terms of activity and stability The possible reason was due to the high Pt metal dispersion and/or the strong interactions among Pt, Sn, and the support.     

CO2氧化丙烷脱氢制丙烯V-Cr/SBA-15催化剂的研究

以介孔分子筛SBA-15为载体，V和Cr为活性组分，采用浸渍法制备了不同V和Cr质量分数的V-Cr/SBA-15催化剂，研究了其对二氧化碳氧化丙烷制丙烯反应的催化性能，采用XRD、BET、TPR等分析测试技术对催化剂的结构进行了表征。结果表明，催化剂中V组分的质量分数较大时以V2O5物相存在，Cr组分以Cr2O3物相存在，它们对SBA-15分子筛的介孔特征影响不大；V、Cr单组分和双组分催化剂都具有较好的CO2氧化丙烷脱氢制丙烯的催化性能，V和Cr质量分数相同的双组分催化剂比单组分催化剂具有更高的催化活性；在V-Cr/SBA-15催化剂中，V和Cr之间存在一定的相互作用，进而改变了催化剂的氧化还原性能，提高了催化剂的催化性能。     

Silylated Co/SBA-15 catalysts for Fischer-Tropsch synthesis

A series of silylated Co/SBA-15 catalysts were prepared via the reaction of surface Si-OH of SBA-15 with hexamethyldisilazane (HMDS) under anhydrous, vapor-phase conditions, and then characterized by FT-IR, N₂ physisorption, TG, XRD, and TPR-MS. The results showed that organic modification led to a silylated SBA-15 surface composed of stable hydrophobic Si-(CH₃)₃ species even after calcinations and H₂ reduction at 673 K. Furthermore, the hydrophobic surface strongly influenced both metal dispersion and reducibility. Compared with non-silylated Co/SBA, Co/S-SBA (impregnation after silylation) showed a high activity, due to the better cobalt reducibility on the hydrophobic support. However, S-Co/SBA (silylation after impregnation) had the lowest FT activity among all the catalysts, due to the lower cobalt reducibility along with the steric hindrance of grafted -Si(CH₃)₃ for the re-adsorption of α-olefins.     

SBA-15介孔分子筛负载型过渡金属催化燃烧脱除乙腈废气

制备了具有规则孔道结构和较高比表面积的SBA-15介孔分子筛,采用真空旋转蒸发法将过渡金属(Cu,Co,Cr和Mn)负载到SBA-15表面,得到负载型过渡金属催化剂,并将其用于含氰废气催化燃烧的实验中,考察了其催化活性.催化剂的理化性能通过X射线衍射(XRD)、氮气吸附-脱附、透射电子显微镜(TEM)、H2-程序升温还...     

预处理方法对Ru/SBA-15催化丙三醇氢解反应性能的影响(英)

使用浸渍法结合不同预处理方法制备了一系列的Ru/SBA-15催化剂,并将其应用于丙三醇氢解反应中.使用N₂吸附-脱附、X射线衍射、CO化学吸附以及透射电子显微镜等方法对所制备Ru/SBA-15进行了表征.结果表明,催化剂前驱体经过空气焙烧后再经H₂还原的Ru/SBA-15催化剂上Ru的分散度较低,而直接使用H₂处理较高.同时,随着H₂还原温度提高,Ru分散度逐渐降低.保持反应活性接近时,随着Ru分散度的降低,TOF增加.表明Ru/SBA-15催化剂上丙三醇氢解是结构敏感反应.     

Effect of Cu promoter on Ni-based SBA-15 catalysts for partial oxidation of methane to syngas

A series of Ni/SBA-15 catalysts with 5wt% to 15wt% Ni content as well as a series of 12.5%Ni/Cu/SBA-15 catalysts with 1% to 10% copper content were prepared by the impregnation method. The catalytic performance for partial oxidation of methane was investigated in a continuous flow microreactor under atmospheric pressure. The textural and chemical properties of the catalysts were characterized by XRD, TEM, BET and H2-TPR techniques. The results indicated that the catalysts modified with Cu promoter showed better performance than those without modification. For the 12.5%Ni/2.5%/Cu/SBA-15 catalyst, at 850 ◦C the conversion of CH4 reached 97.9% and the selectivity of CO and H2 reached 98.0% and 96.0%, respectively. In XRD patterns of the Ni/Cu/SBA-15 catalyst with 7.5 to 10% Cu contents there were CuO characteristic peaks beside NiO characteristic peaks. The mesoporous structure of SBA-15 was retained in all of the catalysts. TPR analysis of the catalysts revealed that a strong interaction between Ni, Cu promoter and SBA-15 support may be existed. This interaction enhanced significantly the redox properties of the catalysts resulting in the higher catalytic activity.     

SO_4~(2-)/SnO_2/SBA-15固体酸催化剂的制备及其在环酮缩合反应中的应用

采用等体积浸渍法制备了不同负载量的固体酸催化剂SO42-/SnO2/SBA-15,利用X射线粉末衍射、N2吸附-脱附和透射电镜等手段对样品进行了表征,并考察了催化剂对4-叔丁基环己酮与乙二醇缩合反应的催化性能.结果表明,SO42-/SnO2催化剂负载于SBA-15后其催化性能明显改善.研究了SO42-/20%SnO2/SBA-15催化剂上部分酮类化合物与乙二醇及1,2-丙二醇的缩合反应,并考察了反应时间和催化剂用量等因素对反应性能的影响.在适宜的温和条件下,一些环酮类底物如环己酮、4-甲基环己酮和4-叔丁基环己酮等均可反应得到相应的缩醛化产物,且催化剂至少可循环使用4次.     

担载钒氧化物催化剂对丙烷选择氧化性能

用等体积浸渍法制备了SBA-15担载的钒基氧化物催化剂,使用X射线衍射（XRD）分析、氮气吸附、紫外激光拉曼、傅里叶变换红外（FTIR）光谱和紫外-可见漫反射（UV-Vis DRS）光谱对催化剂的结构进行了表征,并评价了催化剂对丙烷选择氧化的活性与选择性.实验结果表明SBA-15载体对丙烷选择氧化的活性优于常规的SiO₂载体.SBA-15担载的低载量催化剂是高分散的催化剂体系,在低钒载量（n（V）/n（Si）<2.5%）时,催化剂具有规则的六方介孔结构.低钒载量（n（V）/n（Si）<0.1%）时,隔离四配位的钒氧化物是丙烷选择氧化生成醛类化合物的活性物种;高钒载量（n（V）/n（Si）>2.5%）时,聚合六配位的钒氧化物和微晶钒氧化物是丙烷脱氢或深度氧化的活性物种.     

Preparation, Characterization and Catalytic Performance of La-SO4/SBA-15 in Esterification of Acetic Acid with n-Butanol

La-SO42-/SBA-15 was synthesized with various amounts of lanthanum via incipient-wetness impregnation. Characterization was done by X-ray diffraction（XRD）, transmission electron micrographs（TEM）, nitrogen adsorption, FTIR spectroscopic analysis, thermogravimetric analysis, and the total amount of acidity of catalyst was estimated by TPD of NH3. The results indicate that lanthanum has been incorporated into SBA-15 molecular sieve. The prepared materials（La-SO42-/SBA-15） keep the highly ordered mesoporous two-dimensional hexagonal structure and do not change the mesoporous channel structure of the support SBA-15. The catalyst showed best catalytic activity in the synthesis of n-butyl acetate. The optimum conditions of the esterification by orthogonal experiments were studied： the molar ratio of n-butanol to acetic acid 1：1.2, the amount of catalyst 7.5%, reaction time 80 min. The yield of n-butyl acetate could reach 93.2% under the optimum conditions. The catalyst was recyclable, cost effective and environmental friendly.     

嫁接法制备Ni/SBA-15催化剂的催化氯苯加氢脱氯

SBA-15表面经嫁接方式引入氨基官能团,与Ni络合制备了SBA-15负载的Ni催化剂(Ni/SBA-15N)。同时,采用传统的浸渍法制备了具有相似Ni负载量的催化剂(Ni/SBA-15)。在负载量相近条件下,Ni/SBA-15N的Ni颗粒分散性均高于Ni/SBA-15。XRD和TPR结果表明,催化剂焙烧后,在氨化SBA-15表面,Ni以硅酸镍形式存在,而在SBA-15表面,Ni以NiO形式存在。Ni/SBA-15对氯苯催化加氢脱氯活性不随Ni负载量的变化而变化;而在Ni/SBA-15N中,Ni负载量增加,催化剂活性增加。     

[Cu(bpdo)2·2H2O]2+-supported SBA-15 nanocatalyst for efficient one-pot synthesis of benzoxanthenone and benzochromene derivatives

A novel [Cu(bpdo)₂·2H₂O]²⁺-supported SBA-15 catalyst (bpdo = 2,2′-bipyridine,1,1′-dioxide) was prepared by the impregnation method. The catalyst was characterized by XRD, TEM, and BET nitrogen adsorption–desorption method, FT-IR, UV–vis, and chemical analysis. XRD patterns and TEM analysis of [Cu(bpdo)₂·2H₂O]²⁺/SBA-15 showed highly ordered hexagonal mesoporous silica, even after immobilization. Also, nitrogen adsorption–desorption isotherms exhibited type-IV isotherms and H1 hysteresis loops according to the IUPAC classification of mesoporous materials. This green support was tested for the synthesis of benzoxanthenone and benzochromene derivatives under solvent-free conditions, with high yield of products via a simple experimental and work-up procedure.     

有序介孔Sn-SBA-15负载铂催化剂上丙烷脱氢性能的提高

丙烷脱氢制丙烯能够将低级烷烃转变成烯烃,是有效扩大丙烯来源的生产工艺.铂锡催化剂用于丙烷催化脱氢的主要缺点是稳定性差、选择性低,通过稳定锡的氧化态可以大大改善催化剂的脱氢性能及稳定性.本文采用一锅水热合成法制备了一系列高比表面积具有高度有序介孔结构的Sn掺杂的Sn-SBA-15材料,并作为载体负载铂催化剂用于丙烷脱氢反应.同时利用传统浸渍法(IM)合成了Sn/SBA-15-IM材料作为对比.结合X射线衍射(XRD)、BET比表面积和孔体积测试、红外光谱(FT-IR)、X射线光电子能谱、H2程序升温脱附(H2-TPD)、热重分析(TGA)、扫描电镜和透射电镜等多种物理化学表征手段研究了Sn-SBA-15材料和催化剂的结构性质及其丙烷脱氢反应性能.XRD和BET比表面积和孔体积测试结果表明,水热合成法原位引入助剂Sn不影响载体SBA-15的有序孔道结构,同时能够保持较大的比表面积.传统浸渍法引入Sn会堵塞载体孔道,载体比表面积及孔道有序度下降.Sn掺杂进入SBA-15骨架能够增强Sn物种与载体的相互作用,有利于Sn物种在反应过程中保持氧化态,提高催化剂丙烷脱氢反应的活性及选择性.当Sn掺杂量增至2.0 wt％时,Pt,Sn组分与载体之间的相互作用减弱,催化剂中Sn0物种所占比例增多,导致催化剂丙烷脱氢性能下降.在丙烷脱氢反应过程中,一锅法引入Sn的催化剂上反应活性和稳定性明显优于浸渍法引入Sn的催化剂.其中,Pt/0.5 Sn-SBA-15催化剂表现出最优的丙烷脱氢性能,丙烷转化率为43.8％,丙烯选择性为98.5％.     

TiO_2/SBA-15的快速合成法及其催化性能

本文针对传统方法合成TiO2/SBA-15的诸多不足,提出了一种简单而快速合成TiO2/SBA-15的方法。利用孔道内水解法快速合成了不同负载量的TiO2/SBA-15。利用XRD、N2-吸脱附、TEM和UV-Vis对样品的晶体结构、微观形貌、光学吸收特性进行了表征,并研究了不同TiO2负载量催化剂对罗丹明B(RhB)光降解活性的影响。结果表明:利用该方法合成的TiO2/SBA-15光催化活性优于传统浸渍方法合成的TiO2/SBA-15与工业上使用的TiO2纳米颗粒。     

Ag/SBA-15低温气相选择性催化氧化苯甲醇合成苯甲醛

以SBA-15为载体,采用浸渍法制备了不同Ag含量的Ag/SBA-15,通过N₂吸附-脱附、X射线衍射、扫描电子显微镜、高分辨透射电子显微镜、X射线光电子能谱和电感耦合等离子体质谱对催化剂进行了表征。将Ag/SBA-15用于苯甲醇气相选择性催化氧化合成苯甲醛,研究了反应条件对转化率和选择性的影响。结果表明,Ag/SBA-15具有均一的一维孔道结构、较厚的孔壁（3-5 nm）及较大的比表面积（411-541 m²/g）,其规整纳米空间的限域作用使一定负载量的Ag以纳米尺寸均匀分散于介孔SBA-15孔道内,增加了活性组分的比表面积。亲核性氧物种从Ag到SBA-15表面的氧溢流,提高了低温下Ag/SBA-15对苯甲醇气相选择性氧化合成苯甲醛的催化性能。5.3% Ag/SBA-15中的Ag粒径为5-6 nm,且均匀分散于载体孔道中,反应温度为220℃时,苯甲醇转化率为87%,苯甲醛选择性为95%;240℃时,苯甲醇转化率和苯甲醛选择性分别高达94%和97%;并在240-300℃范围内,其催化活性和选择性保持不变,表现出了良好的温度耐受能力。催化剂经活化再生可以连续使用40 h,选择性基本保持不变。     

Nanostructured CoMoO4 Supported on Mesoporous SBA-15 for Catalytic Oxidative Dehydrogenation of Propane to Propene

Nanostructured cobalt molybdate catalysts supported on mesoporous silica SBA-15 with different loadings were prepared by citric acid coordination-impregnation method and characterized by XRD, TEM, and BET techniques. The characterization results showed that high loading of well-dispersed crystalline CoMoO₄ may be achieved using citric acid coordination-impregnation method and the mesoporous structure of the support remained intact. The catalytic activity of these catalysts in the oxidative dehydrogenation of propane was investigated. The catalysts of nanostructured cobalt molybdate supported on mesoporous silica SBA-15 showed better catalytic performance than the corresponding bulk composite oxide and nanostructured CoMoO₄ supported on SBA-15 with loading of 13% (mass fraction, w) displayed propene yield of 16.8% at 823 K.     

介孔氧化铝负载Ni-Co氧化物催化剂上丙烷氧化脱氢制丙烯

以非离子型三嵌段共聚物作为模板剂, 异丙醇铝为氧化铝的前驱物, 采用一锅法合成了一系列介孔氧化铝负载镍氧化物、钴氧化物以及镍-钴双金属氧化物催化剂, 并以介孔氧化铝为载体, 采用浸渍法制备了负载Ni-Co 氧化物催化剂. 采用N₂吸附-脱附、高分辨透射电镜(HRTEM)、X射线粉末衍射(XRD)、H₂程序升温还原(H₂-TPR)以及激光拉曼光谱(LRS)等技术对催化剂的结构与性质进行表征, 并考察了催化剂的丙烷氧化脱氢反应性能. 结果表明: 一锅法制备的各催化剂均有大的比表面积和规整的孔道结构, 且负载的金属氧化物高度分散; 而浸渍法制备的催化剂, 其载体的介孔结构被破坏并有Co₃O₄晶相生成. 在考察的催化剂中, 一锅法合成的介孔氧化铝负载Ni-Co 氧化物催化剂表现出最佳的丙烷氧化脱氢性能. 在450 °C、C₃H₈:O₂:N₂的摩尔比为1:1:4和空速(GHSV)为10000 mL·g^-1·h^-1条件下, 该催化剂上丙烯产率为10.3%, 远高于浸渍法制备的催化剂上所获得的丙烯产率(2.4%). 关联催化剂表征和反应结果, 讨论了催化剂结构与性能之间的关系.     

Adsorption and diffusion of propane and propylene in Ag+-impregnated MCM-41

Equilibrium data and diffusion characteristics of propane and propylene were determined on mesoporous adsorbents modified with an organic molecule (APTES) and/or impregnated with AgNO₃, in order to obtain a separation by adsorption via π-complexation. Adsorption capacities were determined by a gravimetric technique, while diffusion characteristics were evaluated by the ZLC technique. The equilibrium isotherms data showed that the modification with an organic molecule will weaken the π-interaction between Ag⁺ and double C=C bond. On the other hand slightly higher adsorption capacities for propylene (about 1.5 mol/kg) were obtained for the sample prepared by a direct impregnation with larger amounts of AgNO₃ (M4 sample). Diffusion runs confirmed that the propane desorption rate on M4 sample was much higher compared to propylene. This evidence leads to a potential application of that adsorbent material for a kinetic separation.