Co-Fe/SBA-15与过一硫酸盐联用非均相催化降解水中染料罗丹明B

由于硫酸根自由基(SO4?-)的强氧化性,基于SO4?-的高级氧化技术受到人们的高度关注.采用过渡金属活化过一硫酸盐(PMS)产生SO4?-用以分解有机物,反应体系简单,反应条件温和,且不需要额外的能量供给,因此,成为人们优先选用的方法,其中,采用高效、环境友好的非均相过渡金属催化剂活化PMS处理难降解有机物成为研究热点.本文研究了非均相CoFe/SBA-15-PMS体系对水中难降解染料罗丹明B(RhB)的降解.以SBA-15为载体, Co(NO3)2·6H2O和Fe(NO3)3·9H2O为前驱物,采用一步等体积浸渍法制备了CoFe/SBA-15,通过X射线衍射(XRD)、N2吸附-脱附、扫描电镜(SEM)、能谱(EDS)、透射电镜(TEM)和振动样品磁强计(VSM)等对其进行了表征.考察了焙烧温度、Co与Fe的负载量对CoFe/SBA-15催化性能的影响和该催化剂的重复使用性能,还考察了RhB降解动力学及催化剂CoFe/SBA-15投加量、氧化剂PMS投加量和反应物(RhB和PMS)初始浓度对其性能的影响,探讨了RhB的降解机理.结果表明：对于催化剂CoFe/SBA-15,合成焙烧后在SBA-15上负载的Fe、Co化合物主要是CoFe2O4复合物,它作为催化剂的活性中心负载在SBA-15的孔道内外.制备的焙烧温度对CoFe/SBA-15催化性能几乎无影响,但对Co浸出影响显著.与SBA-15相比,催化剂10Co9.5Fe/SBA-15-700(Co和Fe负载量分别为10 wt%和9.5 wt%,焙烧温度700 oC)的比表面积、孔体积和孔径均减小,分别为506.1 m2/g,0.669 cm3/g和7.4 nm,但仍然保持SBA-15的有序六方介孔结构.该催化剂以棒状体的聚集态存在,聚集体直径大于0.25μm,其磁化强度为8.3 emu/g,因此,可通过外磁铁容易地从水中分离.相比之下,10Co9.5Fe/SBA-15-700具有最佳的催化性能和稳定性,可使RhB的降解率达到96%以上, Co的浸出量小于32.4μg/L.在CoFe/SBA-15和PMS共存下, RhB的降解符合一级动力学方程, RhB降解速率随CoFe/SBA-15和PMS投加量的增加和初始反应物浓度的减小而提高.淬灭实验结果表明,在CoFe/SBA-15, PMS和RhB水溶液体系中,存在的主要活性自由基为SO4?-,它是由CoFe/SBA-15活化PMS产生的,对RhB的降解起决定性的作用. RhB降解过程的UV-vis结果表明, RhB的降解途径主要是蒽环打开, SO4?-优先攻击RhB的有色芳香烃环,然后RhB进一步分解为小分子有机物. CoFe/SBA-15循环使用10次仍能保持高催化活性和稳定性,在每次反应中RhB的降解率均大于84%, Co和Fe的浸出量均分别小于72.1和35μg/L. CoFe/SBA-15作为高效、环境友好的非均相催化剂可有效地活化PMS产生SO4?-降解水中RhB,具有实际应用的潜力.     

Co-Fe/SBA-15与过一硫酸盐联用非均相催化降解水中染料罗丹明B（英文）

由于硫酸根自由基(SO·-4)的强氧化性,基于SO·-4的高级氧化技术受到人们的高度关注.采用过渡金属活化过一硫酸盐(PMS)产生SO·-4用以分解有机物,反应体系简单,反应条件温和,且不需要额外的能量供给,因此,成为人们优先选用的方法,其中,采用高效、环境友好的非均相过渡金属催化剂活化PMS处理难降解有机物成为研究热点.本文研究了非均相CoFe/SBA-15-PMS体系对水中难降解染料罗丹明B(RhB)的降解.以SBA-15为载体,Co(NO3)2·6H2O和Fe(NO3)3·9H2O为前驱物,采用一步等体积浸渍法制备了CoFe/SBA-15,通过X射线衍射(XRD)、N2吸附-脱附、扫描电镜(SEM)、能谱(EDS)、透射电镜(TEM)和振动样品磁强计(VSM)等对其进行了表征.考察了焙烧温度、Co与Fe的负载量对CoFe/SBA-15催化性能的影响和该催化剂的重复使用性能,还考察了RhB降解动力学及催化剂CoF e/SBA-15投加量、氧化剂PMS投加量和反应物(Rh B和PMS)初始浓度对其性能的影响,探讨了Rh B的降解机理.结果表明:对于催化剂CoFe/SBA-15,合成焙烧后在SBA-15上负载的Fe、Co化合物主要是CoFe2O4复合物,它作为催化剂的活性中心负载在SBA-15的孔道内外.制备的焙烧温度对Co Fe/SBA-15催化性能几乎无影响,但对Co浸出影响显著.与SBA-15相比,催化剂10Co9.5Fe/SBA-15-700(Co和Fe负载量分别为10 wt%和9.5 wt%,焙烧温度700 oC)的比表面积、孔体积和孔径均减小,分别为506.1 m2/g,0.669 cm3/g和7.4 nm,但仍然保持SBA-15的有序六方介孔结构.该催化剂以棒状体的聚集态存在,聚集体直径大于0.25μm,其磁化强度为8.3 emu/g,因此,可通过外磁铁容易地从水中分离.相比之下,10Co9.5Fe/SBA-15-700具有最佳的催化性能和稳定性,可使Rh B的降解率达到96%以上,Co的浸出量小于32.4μg/L.在CoFe/SBA-15和PMS共存下,RhB的降解符合一级动力学方程,Rh B降解速率随CoFe/SBA-15和PMS投加量的增加和初始反应物浓度的减小而提高.淬灭实验结果表明,在Co Fe/SBA-15,PMS和RhB水溶液体系中,存在的主要活性自由基为SO·-4,它是由CoFe/SBA-15活化PMS产生的,对RhB的降解起决定性的作用.RhB降解过程的UV-vis结果表明,RhB的降解途径主要是蒽环打开,SO·-4优先攻击RhB的有色芳香烃环,然后RhB进一步分解为小分子有机物.CoF e/SBA-15循环使用10次仍能保持高催化活性和稳定性,在每次反应中RhB的降解率均大于84%,Co和Fe的浸出量均分别小于72.1和35μg/L.CoFe/SBA-15作为高效、环境友好的非均相催化剂可有效地活化PMS产生SO·-4降解水中RhB,具有实际应用的潜力.     

CuO/SBA-15催化剂上巴豆醛选择性加氢

通过γ-氨丙基三甲氧基硅烷(APTS)偶联与Cu2 离子络合两步法将CuO负载到介孔分子筛SBA-15上,制得CuO/SBA-15催化剂,考察了催化剂的巴豆醛选择性加氢反应性能.通过X射线粉末衍射、氮气吸脱附和程序升温还原(TPR)技术对催化剂进行了表征.结果表明,SBA-15分子筛负载CuO后保持原有的介孔结构,但是孔容和比面表积随着CuO负载量的增大而下降.TPR结果表明CuO/SBA-15系列催化剂有三种CuO物种:高分散CuO、晶相CuO和进入SBA-15分子筛骨架的Cu2 .高分散CuO物种对巴豆醛加氢反应的催化活性最高,晶相CuO物种次之,而进入SBA-15分子筛骨架的Cu2 物种几乎没有活性.     

SBA-15分子筛负载双金属配合物的合成及其催化活性

合成了SBA-15分子筛负载的同双核金属配合物{[M2LCl3]Cl/SBA-15-NH2,M=Co,Cu,Cr,H4L=二(o-亚甲基苯亚甲基三亚乙基四胺}和异双核金属配合物{[CuEuL′](NO3)(H2O)3/SBA-15-NH2,H2L′=N,N′-二(o-羟基-m-甲酰基苯甲基)哌嗪},其结构经UV,1H NMR,IR和元素分析表征。以双核金属配合物为催化剂,过氧化氢为氧化剂,催化二苯甲烷合成二苯甲酮。考察催化剂的种类、反应时间和反应温度对该反应的影响。结果表明,在70℃反应7 h的反应条件下,[Cr2LCl3]Cl/SBA-15-NH2显示了最高的催化活性,二苯甲酮产率达58.1%。     

SBA-15负载金属[Co(Ⅱ),Zn(Ⅱ)]酞菁催化剂的制备及其催化氧化性能

以1,8-二氮杂双环[5,4,0]十一碳烯-7为催化剂,4,5-二丁氧基邻苯二甲腈为原料,用液相法合成了两种金属酞菁配合物——β-八(丁氧基)酞菁钴(1)和β-八(丁氧基)酞菁锌(2),其结构经UV-Vis和IR表征。采用浸渍法将1和2分别负载到有序介孔分子筛SBA-15上制得SBA-15负载金属酞菁催化剂SBA1-15和SBA2-15。以0.1 mol.L-1亚硫酸钠的氧化反应为探针反应,研究了常温常压、氧气气氛下,SBA1-15和SBA2-15的催化氧化活性,并考察了SBA1-15的用量对其催化活性的影响及重复利用性。结果表明,两种催化剂均具有良好的催化性能,在用量相同时,SBA1-15的催化氧化性能优于SBA2-15;SBA1-15的质量为溶液质量的0.16‰时,催化活性最佳,且可以重复使用。     

NiPt/SBA-15纳米催化剂的制备及其催化水合肼分解产氢性能研究

本研究采用浸渍还原法制备了不同金属比例的NiPt双金属负载SBA-15（介孔二氧化硅）催化剂,对其催化水合肼脱氢性能进行了研究。研究结果表明,在催化剂的制备过程中Pt和Ni形成了合金,两种金属的电子协同效应可以有效地促进催化剂的催化性能,SBA-15与金属活性组分之间的相互作用有助于改善催化剂的催化性能和循环稳定性。Pt6Ni4/SBA-15催化剂催化水合肼脱氢的反应活化能为45.6 kJ/mol,TOF值为2123.3 h-1,优于大部分已经报道的催化剂。     

Cu-Zn-Zr/SBA-15介孔催化剂的制备及CO2加氢合成甲醇的催化性能

以具有骨架结构的SBA-15介孔分子筛为载体,采用浸渍法合成了具有高比表面积、不同金属氧化物含量的Cu-Zn-Zr介孔催化剂CZZx/SBA-15(x=0.3,0.4,0.5,0.6).采用N2吸附-脱附(BET)、X射线衍射(XRD)、H2程序升温还原(H2-TPR)、CO2吸附(CO2-TPD)和透射电子显微镜(TEM)等手段对样品进行了表征.在固定床反应器上评价了其CO2加氢合成甲醇的催化性能.实验结果表明,CZZx/SBA-15催化剂具有介孔结构,负载的Cu O,Zn O和Zr O2能够很好地分散在表面,并且负载氧化物晶粒尺寸不同.催化剂的铜比表面积SCu与甲醇催化活性呈近似线性关系,其中CZZ0.4/SBA-15催化剂表现出最大甲醇选择性(54.32%),与CZZ相比,甲醇选择性增加24.85%.随着金属氧化物负载量的增大,催化剂比表面积和SCu明显减小,甲醇选择性与收率也相应减小,负载型CZZx/SBA-15催化剂表面结构对CO2加氢合成甲醇反应活性起关键作用.     

负载型Pd/SBA-15催化剂的双烯选择性加氢催化性能

用微型反应器评价体系结合程序升温还原CO、化学吸附、BET比表面积测试和高分辨率透射电子显微镜等多种表征方法研究了负载型Pd/SBA-15催化剂的长链正构双烯选择性加氢的催化性能.结果表明,与Pd/-γAl2O3工业催化剂相比,Pd/SBA-15催化剂双烯选择性加氢的催化性能更优良,且Pd/SBA-15催化剂双烯选择性加氢催化性能与Pd负载量密切相关.随Pd负载量增加,Pd/SBA-15催化剂的金属分散度和长链正构双烯加氢选择性急剧下降.     

PtZn-Sn/SBA-15合成、表征及对丙烷催化脱氢性能

以SBA-15为载体,利用浸渍法制备了单、双和三金属Pt催化剂,并对催化剂进行了N2物理吸附(BET)、程序升温还原(H2-TPR)、H2-化学吸附、透射电子显微镜(TEM)和O2-脉冲等技术表征,研究了它们对丙烷催化脱氢(CDH)制丙烯反应的催化性能。研究结果表明,Pt在三金属催化剂中的分散性能最好,并且部分负载组分可以进入SBA-15的孔道,Pt的分散度达到29%,Pt粒子尺寸为3 nm左右。三金属催化剂表现出优越的脱氢性能,这主要归结于载体的弱酸性、活性组分和助剂、载体之间的相互作用及Zn对Pt的电子调控作用。这些因素使催化剂的积炭量较低,因而具有较高的脱氢稳定性和极高的选择性。     

Preparation and Hydrodesulfurization Performance of Ni-B Amorphous Alloy Catalyst Supported by APTS Modified SBA-15

采用共价接枝法制备APTS改性介孔分子筛SBA-15,将氨基官能团接枝到SBA-15表面.并采用化学还原法制备了Ni-B/SBA-15-APTS非晶态合金催化剂,以噻吩加氢脱硫为探针反应,研究了其催化加氢脱硫性能.结果表明,240℃时,APTS改性SBA-15所负载的Ni-B催化剂噻吩转化率达到50.8%,较未改性SBA-15所负载的催化剂噻吩转化率有显著地提高.由于氨基与Ni2＋的配合作用,有助于Ni在催化剂中的分散,因而更容易被还原.ICP结果表明,在相同的制备条件下,相比未改性的SBA-15,APTS改性SBA-15使其催化剂中Ni的负载量增加,并且非晶态合金组成中Ni的含量也增大,B的含量降低,有利于提高催化剂的活性.     

Binding of nitrate to a CuII-cyclen complex bearing a ferrocenyl pendant: synthesis, solid-state X-ray structure, and solution-phase electrochemical and spectrophotometric studies

The reaction of Cu(NO3)2.3H2O with the ligand 1-(ferrocenemethyl)-1,4,7,10-tetraazacyclododecane (L) in acetonitrile leads to the formation of a blue complex, [Cu(L)(NO3)][NO3] (C1). The X-ray structure determination shows an unexpected binding of a nitrate anion in that the CuII center is surrounded by four N atoms of the 1,4,7,10-tetraazacyclododecane (cyclen) macrocycle and two O atoms from a chelating nitrate anion, both Cu-O distances being below the sums of the van de Waals radii. Hydrogen-bonding interactions in the crystal lattice and a weak interaction between a second nitrate O and the CuII center in C1 give rise to a highly distorted CuII geometry relative to that found in the known structure of [Cu(cyclen)(NO3)][NO3] (C5). Electrochemical studies in acetonitrile containing 0.1 M [Bu4N][NO3] as the supporting electrolyte showed that oxidation of C1 in this medium exhibits a single reversible one-electron step with a formal potential E degrees f of +85 mV vs Fc0/+ (Fc = ferrocene). This process is associated with oxidation of the ferrocenyl pendant group. Additionally, a reversible one-electron reduction reaction with an E degrees f value of -932 mV vs Fc0/+, attributed to the CuII/I redox couple, is detected. Gradual change of the supporting electrolyte from 0.1 M [Bu4N][NO3] to the poorly coordinating [Bu4N][PF6] electrolyte, at constant ionic strength, led to a positive potential shift in E degrees f values by +107 and +39 mV for the CuII/I(C1) and Fc0/+(C1) redox couples, respectively. Analysis of these electrochemical data and UV-vis spectra is consistent with the probable presence of the complexes C1, [Cu(L)(CH3CN)2]2+ (C2), [Cu(L)(CH3CN)(NO3)]+ (C3), and [Cu(L)(NO3)2] (C4) as the major species in nitrate-containing acetonitrile solutions. In weakly solvating nitromethane, the extent of nitrate complexation remains significant even at low nitrate concentrations, due to the lack of solvent competition.     

Controlled synthesis, characterization, and catalytic properties of Mn(2)O(3) and Mn(3)O(4) nanoparticles supported on mesoporous silica SBA-15

A method established in the present study has proven to be effective in the synthesis of Mn(2)O(3) nanocrystals by the thermolysis of manganese(III) acetyl acetonate ([CH(3)COCH=C(O)CH(3)](3)-Mn) and Mn(3)O(4) nanocrystals by the thermolysis of manganese(II) acetyl acetonate ([CH(3)COCH=C(O)-CH(3)](2)Mn) on a mesoporous silica, SBA-15. In particular, Mn(2)O(3) nanocrystals are the first to be reported to be synthesized on SBA-15. The structure, texture, and electronic properties of nanocomposites were studied using various characterization techniques such as N2 physisorption, X-ray diffraction (XRD), laser Raman spectroscopy (LRS), temperature-programmed reduction (TPR), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS). The results of powder XRD at low angles show that the framework of SBA-15 remains unaffected after generation of the manganese oxide (MnO(x)) nanoparticles, whereas the pore volume and the surface area of SBA-15 dramatically decreased as indicated by N2 adsorption-desorption. TEM images reveal that the pores of SBA-15 are progressively blocked with MnO(x) nanoparticles. The formation of the hausmannite Mn(3)O(4) and bixbyite Mn(2)O(3) structures was clearly confirmed by XRD. The surface structures of MnO(x) were also determined by LRS, XPS, and TPR. The crystalline phases of MnO(x) were identified by LRS with corresponding out-of-plane bending and symmetric stretching vibrations of bridging oxygen species (M-O-M) of both MnO(x) nanoparticles and bulk MnO(x). We also observed the terminal Mn=O bonds corresponding to vibrations at 940 and 974 cm-1 for Mn(3)O(4)/SBA-15 and Mn(2)O(3)/SBA-15, respectively. These results show that the MnO(x) species to be highly dispersed inside the channels of SBA-15. The nanostructure of the particles was further identified by the TPR profiles. Furthermore, the chemical states of the surface manganese (Mn) determined by XPS agreed well with the findings of LRS and XRD. These results suggest that the method developed in the present study resulted in the production of MnO(x) nanoparticles on mesoporous silica SBA-15 by controlling the crystalline phases precisely. The thus-prepared nanocomposites of MnO(x) showed significant catalytic activity toward CO oxidation below 523 K. In particular, the MnO(x) prepared from manganese acetyl acetonate showed a higher catalytic reactivity than that prepared from Mn(NO(3))2.     

Synthesis, characterization, and reactivity of [Ru(bpy)(CH3CN)3(NO2)]PF6, a synthon for [Ru(bpy)(L3)NO2] complexes

We report a high yield, two-step synthesis of fac-[Ru(bpy)(CH3CN)3NO2]PF6 from the known complex [(p-cym)Ru(bpy)Cl]PF6 (p-cym = eta(6)-p-cymene). [(p-cym)Ru(bpy)NO2]PF6 is prepared by reacting [(p-cymene)Ru(bpy)Cl]PF6 with AgNO3/KNO2 or AgNO2. The 15NO2 analogue is prepared using K15NO2. Displacement of p-cymene from [(p-cym)Ru(bpy)NO2]PF6 by acetonitrile gives [Ru(bpy)(CH3CN)3NO2]PF6. The new complexes [(p-cym)Ru(bpy)NO2]PF6 and fac-[Ru(bpy)(CH3CN)3NO2]PF6 have been fully characterized by 1H and 15N NMR, IR, elemental analysis, and single-crystal structure determination. Reaction of [Ru(bpy)(CH3CN)3NO2]PF6 with the appropriate ligands gives the new complexes [Ru(bpy)(Tp)NO2] (Tp = HB(pz)3-, pz = 1-pyrazolyl), [Ru(bpy)(Tpm)NO2]PF6 (Tpm = HC(pz)3), and the previously prepared [Ru(bpy)(trpy)NO2]PF6 (trpy = 2,2',6',2' '-terpyridine). Reaction of the nitro complexes with HPF6 gives the new nitrosyl complexes [Ru(bpy)TpNO][PF6]2 and [Ru(bpy)(Tpm)NO][PF6]3. All complexes were prepared with 15N-labeled nitro or nitrosyl groups. The nitro and nitrosyl complexes were characterized by 1H and 15N NMR and IR spectroscopy, elemental analysis, cyclic voltammetry, and single-crystal structure determination for [Ru(bpy)TpNO][PF6]2. For the nitro complexes, a linear correlation is observed between the nitro 15N NMR chemical shift and 1/nu(asym), where nu(asym) is the asymmetric stretching frequency of the nitro group.     

Syntheses, characterization, and magnetic studies of copper(II) complexes with the ligand N,N,N',N'-tetrakis(2-pyridylmethyl)-1,3-benzenediamine (1,3-tpbd) and its phenol derivative 2,6-bis[bis(2-pyridylmethyl)amino]-p-cresol] (2,6-Htpcd)

The copper(II) complexes [Cu(4)(1,3-tpbd)(2)(H(2)O)(4)(NO(3))(4)](n)(NO(3))(4n)·13nH(2)O (1), [Cu(4)(1,3-tpbd)(2)(AsO(4))(ClO(4))(3)(H(2)O)](ClO(4))(2)·2H(2)O·0.5CH(3)OH (2), [Cu(4)(1,3-tpbd)(2)(PO(4))(ClO(4))(3)(H(2)O)](ClO(4))(2)·2H(2)O·0.5CH(3)OH (3), [Cu(2)(1,3-tpbd){(PhO)(2)PO(2)}(2)](2)(ClO(4))(4) (4), and [Cu(2)(1,3-tpbd){(PhO)PO(3)}(2)(H(2)O)(0.69)(CH(3)CN)(0.31)](2)(BPh(4))(4)·Et(2)O·CH(3)CN (5) [1,3-tpbd = N,N,N',N'-tetrakis(2-pyridylmethyl)-1,3-benzenediamine, BPh(4)(-) = tetraphenylborate] were prepared and structurally characterized. Analyses of the magnetic data of 2, 3, 4, and [Cu(2)(2,6-tpcd)(H(2)O)Cl](ClO(4))(2) (6) [2,6-tpcd = 2,6-bis[bis(2-pyridylmethyl)amino]-p-cresolate] show the occurrence of weak antiferromagnetic interactions between the copper(II) ions, the bis-terdentate 1,3-tpbd/2,6-tpcd, μ(4)-XO(4) (X = As and P) μ(1,2)-OPO and μ-O(phenolate) appearing as poor mediators of exchange interactions in this series of compounds. Simple orbital symmetry considerations based on the structural knowledge account for the small magnitude of the magnetic couplings found in these copper(II) compounds.     

Heterospin systems constructed from [Cu2Ln]3+ and [Ni(mnt)2]1-,2- Tectons: First 3p-3d-4f complexes (mnt = maleonitriledithiolato)

New heterospin complexes have been obtained by combining the binuclear complexes [{Cu(H(2)O)L(1)}Ln(O(2)NO)(3)] or [{CuL(2)}Ln(O(2)NO)(3)] (L(1) = N,N'-propylene-di(3-methoxysalicylideneiminato); L(2) = N,N'-ethylene-di(3-methoxysalicylideneiminato); Ln = Gd(3+), Sm(3+), Tb(3+)), with the mononuclear [CuL(1)(2)] and the nickel dithiolene complexes [Ni(mnt)(2)](q)- (q = 1, 2; mnt = maleonitriledithiolate), as follows: (1)infinity[{CuL(1)}(2)Ln(O(2)NO){Ni(mnt)(2)}].Solv.CH(3)CN (Ln = Gd(3+), Solv = CH(3)OH (1), Ln = Sm(3+), Solv = CH(3)CN (2)) and [{(CH(3)OH)CuL(2)}(2)Sm(O(2)NO)][Ni(mnt)(2)] (3) with [Ni(mnt)2]2-, [{(CH(3)CN)CuL(1)}(2)Ln(H(2)O)][Ni(mnt)(2)]3.2CH(3)CN (Ln = Gd(3+) (4), Sm(3+) (5), Tb(3+) (6)), and [{(CH(3)OH)CuL(2)}{CuL(2)}Gd(O(2)NO){Ni(mnt)(2)}][Ni(mnt)(2)].CH(2)Cl(2) (7) with [Ni(mnt))(2]*-. Trinuclear, almost linear, [CuLnCu] motifs are found in all the compounds. In the isostructural 1 and 2, two trans cyano groups from a [Ni(mnt)2]2- unit bridge two trimetallic nodes through axial coordination to the Cu centers, thus leading to the establishment of infinite chains. 3 is an ionic compound, containing discrete [{(CH(3)OH)CuL(2)}(2)Sm(O(2)NO)](2+) cations and [Ni(mnt)(2)](2-) anions. Within the series 4-6, layers of discrete [CuLnCu](3+) motifs alternate with stacks of interacting [Ni(mnt)(2)](*-) radical anions, for which two overlap modes, providing two different types of stacks, can be disclosed. The strength of the intermolecular interactions between the open-shell species is estimated through extended Hückel calculations. In compound 7, [Ni(mnt)(2)](*-) radical anions coordinate group one of the Cu centers of a trinuclear [Cu(2)Gd] motif through a CN, while discrete [Ni(mnt)(2)](*-) units are also present, overlapping in between, but also with the coordinated ones. Furthermore, the [Cu(2)Gd] moieties dimerize each other upon linkage by two nitrato groups, both acting as chelate toward the gadolinium ion from one unit and monodentate toward a Cu ion from the other unit. The magnetic properties of the gadolinium-containing complexes have been determined. Ferromagnetic exchange interactions within the trinuclear [Cu(2)Gd] motifs occur. In the compounds 4 and 7, the [Ni(mnt)(2)](*-) radical anions contribution to the magnetization is clearly observed in the high-temperature regime, and most of it vanishes upon temperature decrease, very likely because of the rather strong antiferromagnetic exchange interactions between the open-shell species. The extent of the exchange interaction in the compound 7, which was found to be antiferromagnetic, between the coordinated Cu center and the corresponding [Ni(mnt)(2)](*-) radical anion, bearing mostly a 3p spin type, was estimated through CASSCF/CASPT2 calculations. Compound 6 exhibits a slow relaxation of the magnetization.     

高效甲醇水蒸气重整制氢的SBA-15改性的Cu/ZnO/Al2O3催化剂

以介孔SBA-15为结构助剂, 制备出用于甲醇水蒸气重整制氢的新型高效氧化硅掺杂的Cu/ZnO/Al₂O₃催化剂, 并与传统Cu/ZnO/Al₂O₃催化剂在相同条件下的催化性能进行了比较. 结果表明, 添加适量介孔SBA-15可显著提高催化剂的催化活性和选择性, 在大幅度提高甲醇转化率的同时有效降低了重整产气中CO的含量. 原位XRD分析证实适量介孔SBA-15的添加对传统Cu/ZnO/Al₂O₃催化剂的微结构性质可产生重要的调控作用, 从而大大改善其催化活性和制氢选择性.     

Synthesis and Crystal Structure of［Lu（NO_3）_3（H_2O）_2（CH_3CN）］（Benzo－15－C－5）·CH_3CN

ＳｙｎｔｈｅｓｉｓａｎｄＣｒｙｓｔａｌＳｔｒｕｃｔｕｒｅｏｆ［Ｌｕ（ＮＯ_３）_３（Ｈ_２Ｏ）_２（ＣＨ_３ＣＮ）］（Ｂｅｎｚｏ－１５－Ｃ－５）·ＣＨ_３ＣＮＷａｎｇＲｕｉ－Ｙａｏ；ＪｉｎＺｈｏｎｇ－Ｓｈｅｎｇ；ＮｉＪｉａ－Ｚｕａｎ（Ｌａｂｏｒａｔｏｒｙｏ...     

Crystal Structure of catena-[(Tetrakis-μ2-acetato-μ2-4,4'-bipyridine) dicopper(Ⅱ)] Acetonitrile Solvate

The title compound,[Cu2(CH3COO)4(C8H10N2)]n·nCH3CN1 (C8H10N2,4,4'-bipy = 4,4'-bipyridine),has been solvothermally synthesized in CH3CN and characterized by X-ray diffraction.The crystal is of monoclinic,space group Cc with a = 22.626(6),b = 14.012(4),c =15.106(4) (A),β = 107.610(3)°,V = 4565(2) (A)3,C20H23Cu2N3O8,Mr = 560.49,Z = 8,Dc = 1.631 g/cm3,μ = 1.914 mm-1,Flack parameter = 0.48(1),F(000) = 2288,R = 0.042 and wR = 0.)98 for 8887 observed reflections (I ＞ 2σ(I)).It consists of nearly linear one-dimensional chains [Cu2(CH3COO)4(C8H10N2)]n derived from paddle-wheel [Cu2(CH3COO)4] unit linked by 4,4'-bipy,and CH3CN as guest molecule regularly decorates between the chains.     

Alkane hydroperoxidation with peroxides catalysed by copper complexes

Various copper(I) and copper(II) derivatives, both "simple" ones (copper acetate, perchlorate and a complex with CH3CN) and compounds containing N,O-chelating ligands, catalyse very efficient (turnover numbers attain 2200) oxidation of saturated hydrocarbons with peroxyacetic acid (PAA) or tert-butyl hydroperoxide (TBHP) in acetonitrile solution at 60 degrees C. Alkyl hydroperoxide, alcohol and ketone are formed, the main product being an alkyl hydroperoxide in the oxidation with PAA and an alcohol for the case of TBHP. It has been proposed that the oxidation with PAA is induced via the attack of species r* [HO* or CH3C(=O)O*] on the alkane, RH. A competitive attack of r* on the solvent, CH3CN, also occurs. It has been assumed that in the case of the reaction catalysed by complex Cu(CH3CN)4BF4, copper is present mainly in the form of Cu+ cation, and the rate-limiting step of the oxidation process is the formation of r* via reaction (1): CH3C(=O)OOH + Cu+ --> CH3C(=O)O* + HO- + Cu2+ or/and CH3C(=O)OOH + Cu+ --> CH3C(=O)O- + HO* + Cu2+ with initial rate W1 = k1[PAA][Cu(CH3CN)4BF4] and k1 = 1.7 mol(-1) dm3 s(-1) at 60 degrees C. The activity of the Cu-catalyst is dramatically changed on a small modification of N,O-chelating ligands in the catalyst.