旋涂速度对制备P3HT有机场效应晶体管性能的影响（英文）

采用溶液化的方法制备了以PMMA为绝缘层、P3HT为有源层的有机场效应晶体管。研究了P3HT有源层和PMMA绝缘层的旋涂速度对器件性能的影响。实验结果表明,当P3HT和PMMA的旋涂速度均为2 000 r/min时,器件的性能最佳。峰值场效应迁移率为6.84×10-2cm2·V-1·s-1。结果表明,选择适当的旋涂速度是一种有效提高溶液化制备有机场效应晶体管性能的方法。     

PVA栅绝缘层浓度对P3HT有机场效应晶体管性能的影响

采用溶液制备法制备了用PVA作为绝缘层、P3HT作为有源层的有机场效应晶体管,,研究了不同浓度PVA栅绝缘层对器件性能的影响。实验结果显示,以质量分数为8%的PVA溶液制备的栅绝缘层具有最好的性能,器件的场效应迁移率为0.31 cm²·V^-1·s^-1,阈值电压为-6 V。进一步分析了PVA栅绝缘层浓度对器件性能提高的原因,结果表明,对于制备溶液化的有机场效应晶体管,选取合适的PVA栅绝缘层浓度非常重要。     

柔性有机场效应晶体管研究进展

柔性有机场效应晶体管具有可折叠、质量轻、低成本等优点,在柔性显示、柔性传感器、柔性射频标签和柔性集成电路等方面显示了广阔的应用前景.本文在介绍柔性有机场效应 晶体管最新研究进展的基础上, 总结了柔性有机场效应晶体管的器件结构和柔性有机场效应晶体管所使用的衬底材料、 栅绝缘层材料、有源层材料及电极材料, 阐述了柔性有机场效应晶体管的制备工艺, 并讨论了不同的弯曲方式对柔性有机场效应晶体管性能的影响, 最后总结和展望了柔性有机场效应晶体管的应用领域. 关键词： 柔性 晶体管 有机/聚合物 溶液加工     

旋涂速度对制备P3HT有机场效应晶体管性能的影响

采用溶液化的方法制备了以PMMA为绝缘层、P3HT为有源层的有机场效应晶体管.研究了P3HT有源层和PMMA绝缘层的旋涂速度对器件性能的影响.实验结果表明,当P3HT和PMMA的旋涂速度均为2 000 r/min时,器件的性能最佳.峰值场效应迁移率为6.84×10^-2 cm²·V^－1·s^－1.结果表明,选择适当的旋涂速度是一种有效提高溶液化制备有机场效应晶体管性能的方法.     

基于聚合物共混的有机场效应晶体管光电性能研究

采用聚合物共混的方法制备了体异质结薄膜,将其作为光敏半导体层制备了有机场效应光晶体管.利用原子力显微镜表征了共混薄膜的分相情况,探究了器件提高激子解离效率的机理,并对比了聚合物共混前后有机场效应晶体管的光电性能变化和相分离情况.结果表明：制备的聚合物共混光晶体管在微弱光线条件下(0.038 mW/cm²,808 nm)具有较高的光敏性(为10⁶).通过共混聚合物半导体材料制备体异质结薄膜可以有效地提高激子解离的效率,通过双层绝缘层能进一步降低光晶体管的暗电流,从而提高器件的光敏性.     

基于栅绝缘层表面修饰的有机场效应晶体管迁移率的研究进展

栅绝缘层的表面性质对有机场效应晶体管（OFETs）的半导体薄膜的形貌、晶粒生长的有序性和载流子的传输有着重大的影响．研究表明,通过改进栅绝缘层的表面性质,可以有效提高有机场效应晶体管的迁移率．本文综述了OFETs绝缘层表面的粗糙度和表面能对OFETs迁移率的影响,重点探讨了栅绝缘层表面修饰常用的方法,即自组装单层（SAMs）修饰和聚合物修饰与迁移率改进之间的研究进展．最后,展望了该研究方向未来可能的发展趋势．     

Ta_2O_5-PMMA复合栅绝缘层对OFETs性能的影响（英文）

选用五氧化二钽(Ta_2O_5)-聚甲基丙烯酸甲酯(PMMA)复合材料作为栅绝缘层制备了并五苯有机场效应晶体管(OFETs)。通过在Ta_2O_5表面旋涂一层PMMA可以降低栅绝缘层的表面粗糙度,增大其场效应晶体管的迁移率。研究了厚度在20~60 nm范围内的PMMA对复合绝缘层表面形貌、粗糙度以及器件电学性能的影响。结果表明,当PMMA厚度为40 nm时,器件的电学性能最佳。与单一的Ta_2O_5栅绝缘层器件相比,其场效迁移率由4.2×10~(-2)cm~2/(V·s)提高到0.31 cm~2/(V·s);栅电压增加到-20 V时,开关电流比由2.9×10~2增大到2.9×10~5。     

有机场效应晶体管材料及器件研究进展

有机场效应晶体管(organic field—effect transistor，OFET)作为新一代半导体晶体管因其广阔的应用前景和近年来技术上的突飞猛进，使之成为微电子和信息领域科学研究和产品开发中热门的话题之一．文章慨述了有机场效应晶体管的材料研究、器件制备技术以及有机场效应晶体管在各领域中应用的最新进展．     

Ta2O5-PMMA复合栅绝缘层对OFETs性能的影响

选用五氧化二钽（Ta₂O₅）-聚甲基丙烯酸甲酯（PMMA）复合材料作为栅绝缘层制备了并五苯有机场效应晶体管（OFETs）。通过在Ta₂O₅表面旋涂一层PMMA可以降低栅绝缘层的表面粗糙度,增大其场效应晶体管的迁移率。研究了厚度在20~60 nm范围内的PMMA对复合绝缘层表面形貌、粗糙度以及器件电学性能的影响。结果表明,当PMMA厚度为40 nm时,器件的电学性能最佳。与单一的Ta₂O₅栅绝缘层器件相比,其场效迁移率由4.2×10^-2 cm²/（V·s）提高到0.31 cm²/（V·s）;栅电压增加到-20 V时,开关电流比由2.9×10²增大到2.9×10⁵。     

衬底加热和电极修饰对提高有机场效应晶体管性能的影响

通过衬底加热和氧化钼(MoO3)修饰源漏极制备了并五苯有机场效应晶体管.研究了衬底温度和电极修饰层厚度对器件性能的影响.实验结果表明:当衬底温度为60℃、MoO3修饰层为10 nm时,器件性能获得了显著增强,场效应迁移率由原来的3.39×10-3 cm2/(V·s)提高到2.25 ×10-1 cm2/(V·s),阈值电压由12 V降低到3V.器件性能的改善归因于:衬底加热可以优化有源层形貌,改善载流子传输;而MoO3修饰层显著降低了电极与有源层之间的接触势垒,提高了载流子的注入.因此,衬底加热与电极修饰对于制备高性能有机场效应晶体管是不可或缺的优化手段.     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Theoretical analysis and simulation of conjugate heights for dual-conjugate AO system in lidar

A multi-conjugate adaptive optics （MCAO） can offer a possibility of widening field of view （FOV） characterized by the isoplanatic angle, and the choose of conjugate height becomes a basic problem for MCAO, which influences the size of iosplanatic angle. Considering the application of lidar, the isoplanatic angle＇s expressions of two deformable mirrors （DMs） MCAO for uplink and downlink are deduced. The effects of conjugate heights for dual-conjugate AO are thoughtfully discussed, and the isoplanatic angles are further analyzed. The results show that the isopanatic angle varies with the conjugate height and reaches the maximum as the conjugate height is at the optimal altitude. Moreover, the optimal conjugate height changes with the propagation distance.     

Quick single-photon detector with many avalanche photo diodes working on the time division

Due to the limit of response speed of the present single-photon detector, the code rate is still too low to come into practical use for the present quantum key distribution (QKD) system.A new idea is put up to design a quick single-photon detector.This quick single-photon detector is composed of a multi-port optic-fiber splitter and many avalanche photo diodes (APDs).Au of the ports with APDs work on the time division and cooperate with a logic discriminating and deciding unit driven by the clock signal.The operation frequency lies on the number N of ports, and can reach N times of the conventional single-photon detector.The single-photon prompt detection can come true for high repetition-rate pulses.The applying of this detector will largely raise the code rate of the QKD, and boost the commercial use.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.