二维六方p6mm有序介孔WO_3-TiO_2复合材料的制备及其可见光光催化性能

以非离子型表面活性剂为模板剂,采用蒸发诱导自组装法制备了一系列不同WO3含量的有序介孔WO3-TiO2复合材料,并表征了其孔结构、形貌、孔隙率、光谱性质及组成.结果表明,该材料呈二维六方p6mm对称和锐钛矿晶相结构;与无序WO3-TiO2复合材料相比,其比表面积(152～154m2/g)更大,孔径更均一(5.3nm),且比纯TiO2的帯隙宽度(3.0eV)更窄.将该WO3-TiO2样品用于可见光光催化降解水相中罗丹明B和2,4-二氯苯氧乙酸的反应中,发现WO3含量适当的有序介孔WO3-TiO2样品的光催化活性比无序的样品和纯TiO2的更高.     

W掺杂SiO2介孔材料的制备与表征

以非离子表面活性剂三嵌段共聚物P123为模板剂、正硅酸乙酯(TEOS)为硅源、钨酸钠(Na2WO4·2H2O)为钨源, 通过水热法一步合成了W掺杂的二氧化硅介孔材料W-SiO2, 并通过XRD、HRTEM、EDX、FT-IR、N2吸附-脱附等表征手段, 考察了随着W含量增加, W-SiO2介孔材料结构的变化规律以及钨物种在材料中的存在状态. 结果表明, 当WO3含量w(WO3)约为10%时, W-SiO2中的钨物种是高度分散进入介孔骨架,形成W-O-Si 键; 当w(WO3)=20%时, 样品中开始有未掺入到SiO2骨架中WO3的结晶出现; 当w(WO3)约60%时, W-SiO2 样品能保持很好的介孔孔道结构, 更高含量WO3掺入将破坏二氧化硅介孔结构.     

银纳米颗粒负载阶层多孔二氧化硅块体的制备及表征

以溶胶-凝胶伴随相分离法制备的阶层多孔二氧化硅作为载体,3-氨丙基三乙氧基硅烷(APTES)为改性剂,乙醇为还原剂,在阶层多孔二氧化硅固体骨架上进行银纳米颗粒均匀负载.利用扫描电镜(SEM)、透射电镜(TEM)、X射线衍射(XRD)、汞压、N2吸附/脱附、X射线光电子能谱(XPS)等测试技术对银纳米颗粒负载阶层多孔二氧化硅进行了表征,探讨了APTES表面改性、乙醇还原机理以及银纳米颗粒负载块体的孔结构特征变化规律.结果表明:APTES表面改性将氨基接枝于阶层骨架上,氨基与银离子形成银氨离子,银氨离子经乙醇还原后将平均粒径约16 nm的银纳米颗粒成功负载于二氧化硅的大孔及介孔内部;负载后的阶层多孔块体的大孔骨架未受到破坏,但其比表面积由418 m2·g-1下降到254m2·g-1,两次还原负载能提高银纳米颗粒的负载量.     

多孔二氧化硅负载硅钨酸催化合成柠檬酸三丁酯

以硅酸钠为硅源,十六烷基三甲基溴化铵为模板剂,采用溶胶–凝胶法合成了负载型硅钨酸/二氧化硅(STA/SiO2)催化剂,并采用红外光谱、氮吸附-脱附、热重对其结构和性质进行了表征。结果表明,所制备的硅钨酸/二氧化硅同时具有微孔和介孔结构,且硅钨酸负载后热稳定性有所提高。以柠檬酸三丁酯的合成作为探针反应,考察了制备催化剂时溶液pH值、硅钨酸负载量对催化剂催化性能的影响。结果表明在pH为9,硅钨酸负载量为50%时,制备的硅钨酸/二氧化硅具有较好的催化活性和重复使用性,该催化剂初次使用时,柠檬酸的转化率在300min可达到89.09%,重复使用6次,柠檬酸的转化率在300min仍可达到86.86%。通过对反应动力学进行研究,发现柠檬酸三丁酯的合成反应为一级反应。     

介孔碳球的制备及其催化性能研究

通过在3-氨基苯酚与甲醛聚合成球的过程中引入模板剂二氧化硅纳米颗粒,随后碳化、腐蚀除硅,制备得到了具有良好介孔结构的碳纳米球.通过透射电子显微镜(TEM)、粉末X射线衍射(XRD)、N_2等温吸脱附(BET)等表征手段对样品形貌和结构进行了分析,表明介孔碳球分散性良好、比表面积较大(~294m~2/g)、孔径分布均匀(~3.8nm).以该介孔碳球为载体,负载金属钯纳米颗粒,得到了金属颗粒分散均匀、粒径小(~2nm)的Pd/介孔碳球复合材料.应用于催化碘苯和苯硼酸的Suzuki偶联反应中,具有良好的催化活性.反应5min,碘苯的转化率达99.06%,催化剂循环使用7次,碘苯转化率未见明显下降.     

双模板法合成介孔/大孔二级孔道碳材料

以酚醛树脂低聚物为前驱物, 利用双模板法制备了具有介孔/大孔双孔结构的碳材料. 其中以二氧化硅蛋白石为大孔模板, 以嵌段共聚物自组装结构为介孔模板. 对样品进行了扫描电子显微镜(SEM), 透射电子显微镜(TEM), X射线衍射(XRD)和氮气吸附-脱附实验表征. 结果表明所制备的双孔碳材料大孔直径约为230 nm, 介孔直径10 nm.     

碳/碳化铁复合介孔材料的合成及储氢性能!

以1-氰甲基-3-甲基咪唑四氯化铁盐([MCNIm]+[FeCl4]-)为前体,SBA-15为模板,采用硬模板纳米浇筑法合成碳/碳化铁复合介孔材料.研究了合成温度和时间对所得材料比表面积的影响.利用氮气吸附-脱附、X射线衍射、透射电子显微镜及X射线光电子能谱等对材料进行表征.结果显示,在800℃下煅烧能够得到相对较大比表面积的材料,同时延长煅烧时间可以得到高比表面积、孔径分布均匀且结构较完整的材料,其最大比表面积可达517.96 m2/g.此外,氢气吸附测试表明,此种材料具有一定的储氢性能.     

带坑WO3单晶纳米片的合成与光学性能

以介孔二氧化硅(SBA-15)为硬模板, 钨酸钠(Na₂WO₄•2H₂O)为钨源, 在酸性条件下, 用改进的浸渍-还原法合成了具有纳米坑结构的单晶片状WO₃材料. 用X射线衍射(XRD)、能量扩散X射线(EDX)、扫描电子显微镜(SEM)、高分辨透射电镜(HRTEM)和紫外-可见光区透射光谱(UV-Vis)等手段对产物的组成、形貌和光学性能进行了表征. 结果表明, 获得的产物为带有纳米坑结构的单晶片状WO₃, 且在近紫外-可见光区具有较高的透射率. 此外, 随着煅烧温度的升高, WO₃由单斜相转变为单斜相与正交相的混合相, WO₃薄膜的紫外-可见光透射率随煅烧温度升高而升高.     

三维有序大孔复合材料AgZnO-TiO2的制备及微波辅助光催化性能

采用聚苯乙烯(PS)微球作为模板剂,经溶胶-凝胶及煅烧后处理等方法制备了三维有序大孔复合材料Ag/ZnO-TiO2. 通过傅里叶-红外光谱(FT-IR)、X 射线衍射(XRD)、X 射线光电子能谱(XPS) 、N2吸附-脱附测定和扫描电子显微镜配合X 射线能量色谱仪(SEM-EDS)等测试手段对其组成、结构及形貌等进行了表征. 结果显示,经PS微球处理后的Ag/ZnO-TiO2具有锐钛矿晶型结构,其Ag以单质形式存在. 该复合材料的孔结构排列整齐有序,孔壁为介孔结构,粒子堆积致密,平均孔直径约150 nm,属于三维有序大孔材料(3DOM). 在微波辅助光催化降解甲基橙等染料的实验研究中,该复合材料表现出较好的光催化性能,其活性明显高于P25等单体以及二元体系ZnO-TiO2     

有序介孔C-Al2O3纳米复合材料的合成及其红外发射率

以嵌段共聚物F127(PEO106PPO70PEO106, MW=12600)为模板剂, 异丙醇铝为铝源, 低分子量的酚醛树脂为碳源, 通过溶胶-凝胶三元共组装法合成了C-Al2O3纳米复合材料. 用X射线衍射(XRD)、透射电子显微镜(TEM)及N2吸脱附法对该复合材料进行结构与性能表征, 结果显示复合材料MC5A5具有较好的有序介孔结构, 其比表面积可达175 m2·g-1, 孔容0.22 cm3·g-1. 又以三元乙丙橡胶(EPDM)为粘结剂, 与介孔纳米复合材料混合制备涂层. 随着复合材料中Al2O3质量分数从30%增加到70%, 该涂层的红外发射率从0.575降至0.456, 表明Al2O3能有效降低复合材料的红外发射率, 预示该复合材料在军事装备隐身需求领域将具有较好的应用前景.     

一步制备高比表面积介孔Co3O4-CeO2及其表征

以有序介孔二氧化硅KIT-6为硬模板,硝酸钴、硝酸铈为金属源,分别在真空辅助条件和普通搅拌条件下制备了介孔CoCeOx复合氧化物。采用XRD、SEM、TEM、N2吸脱附等技术表征了复合氧化物的物化性质,并评价其氧化甲苯的性能。结果表明,在真空辅助和搅拌条件下制备的CoCeOx氧化物是由Co3O4和CeO2组成的介孔Co3O4-CeO2复合氧化物,其比表面积分别为141和89 m^2·g^-1,平均孔径分别为8.7和9.6 nm。真空辅助纳米复制过程有利于金属盐的前驱体充分填充到模板的孔隙中,去除模板后,可以得到有序的介孔复合金属氧化物。所制备介孔钴铈复合氧化物具有孔道有序性好、比表面积大的特点,在挥发性有机化合物的氧化去除方面具有一定的应用前景。     

One-step-impregnation hard templating synthesis of high-surface-area nanostructured mixed metal oxides (NiFe2O4, CuFe2O4 and Cu/CeO2)

We report here on an efficient one-step-impregnation method to synthesize crystalline mesoporous bimetal oxides (e.g. NiFe(2)O(4), CuFe(2)O(4), Cu/CeO(2)) using mesoporous silicas as hard templates under optimized mixing conditions. This new procedure enables a true replication of the mesostructure with high yield and phase purity, while retaining particle morphology of the template.     

基于表面金属有机化学方法的硅胶表面氧化钛的制备及表征

以普通硅胶为载体, 采用表面金属有机化学合成技术, 通过“一锅”反应制备了硅胶表面金属有机钛化合物, 然后经高温煅烧获得了硅胶表面氧化钛. 采用傅里叶变换红外光谱(FTIR)、 X射线光电子能谱(XPS)、 热重分析(TG-DTA)及原子力显微镜(AFM)对硅胶表面金属有机钛化合物和表面氧化钛进行了结构表征. 结果表明, 高温煅烧过程中, 硅胶表面金属有机钛化合物不仅脱除了有机配体, 并且通氧使其表面“再生”羟基, 确保了钛的四配位形式不变; 氧化钛通过Si—O—Ti键锚定在硅胶表面, 呈分散、 孤立状态分布. 高温煅烧后, 硅胶的骨架结构保持完好.     

Synthesis of highly ordered mesoporous crystalline WS(2) and MoS(2) via a high-temperature reductive sulfuration route

A high-temperature reductive sulfuration method is demonstrated to synthesize highly ordered mesoporous metal sulfide crystallites by using mesoporous silica as hard templates. H2S gas is utilized as a sulfuration agent to in situ convert phosphotungstic acid H3PW12O40.6H2O to hexagonal WS2 crystallites in the silica nanochannels at 600 degrees C. Upon etching silica, mesoporous, layered WS2 nanocrystal arrays are produced with a yield as high as 96 wt %. XRD, nitrogen sorption, SEM, and TEM results reveal that the WS2 products replicated from the mesoporous silica SBA-15 hard template possess highly ordered hexagonal mesostructure (space group, p6mm) and rodlike morphology, analogous to the mother template. The S-W-S trilayers of the WS2 nanocrystals are partially oriented, parallel to the mesochannels of the SBA-15 template. This orientation is related with the reduction of the high-energy layer edges in layered metal dichalcogenides and the confinement in anisotropic nanochannels. The mesostructure can be 3-D cubic bicontinuous if KIT-6 (Iad) is used as a hard template. Mesoporous WS2 replicas have large surface areas (105-120 m2/g), pore volumes ( approximately 0.20 cm3/g), and narrow pore size distributions ( approximately 4.8 nm). By one-step nanocasting with the H3PMo12O40.6H2O (PMA) precursor into the mesochannels of SBA-15 or KIT-6 hard template, highly ordered mesoporous MoS2 layered crystallites with the 2-D hexagonal (p6mm) and 3-D bicontinuous cubic (Iad) structures can also be prepared via this high-temperature reductive sulfuration route. When the loading amount of PMA precursor is low, multiwalled MoS2 nanotubes with 5-7 nm in diameter can be obtained. The high-temperature reductive sulfuration method is a general strategy and can be extended to synthesize mesoporous CdS crystals and other metal sulfides.     

Fabrication and characterization of mesoporous Co3O4 core/mesoporous silica shell nanocomposites

A mesoporous Co(3)O(4) core/mesoporous silica shell composite with a variable shell thickness of 10-35 nm was fabricated by depositing silica on Co(3)O(4) superlatticed particles. The Brunauer-Emmett-Teller (BET) surface area of the composite with a shell thickness of ca. 2.0 nm was 238.6 m(2)/g, which varied with the shell thickness, and the most frequent pore size of the shell was ca. 2.0 nm. After the shell was eroded with hydrofluoric acid, mesoporous Co(3)O(4) particles with a pore size of ca. 8.7 nm could be obtained, whose BET surface area was 86.4 m(2)/g. It is proposed that in the formation of the composite the electropositive cetyltrimethylammonium bromide (CTAB) micelles were first adsorbed on the electronegative Co(3)O(4) particle surface, which directed the formation of the mesoporous silica on the Co(3)O(4) particle surface. Electrochemical measurements showed that the core/shell composites exhibited a higher discharge capacity compared with that of the bare Co(3)O(4) particles.     

"Nanocasting": using SBA-15 silicas as hard templates to obtain ultrasmall monodispersed gamma-Fe2O3 nanoparticles

This work describes the use of mesoporous SBA-15 silicas as hard templates for the size-controlled synthesis of oxide nanoparticles, with the pores acting as nanoscale reactors. This fundamental work is mainly aimed at understanding unresolved issues concerning the occurrence and size dependence of phase transitions in oxide nanocrystals. Aqueous solutions of Fe(NO3)3*9H2O are deposited inside the pores of SBA-15 silicas with mesopore diameters of 4.3, 6.6, and 9.5 nm. By calcination, the nitrate salt transforms into FeOx oxides. The XRD peaks of nanocrystals are broad and overlapping, resulting in ambiguities attributed to a given allotropic variety of Fe2O3 (alpha, epsilon, or gamma) or Fe3O4. The association of XRD, SAED, and Raman information is necessary to solve these ambiguities. The metastable gamma-Fe2O3 variety is selectively formed at low Fe/Si atomic ratio (ca. 0.20) and when a low calcination temperature is used (773 or 873 K followed by quenching to room temperature once the targeted temperature is reached). The small size dispersion of the patterned nanoparticles, suggested on a local scale by TEM, is confirmed statistically by magnetic measurements. The nanoparticles have a superparamagnetic behavior around room temperature. Their magnetic moments (from 220 to 370 mB), their sizes (from 4.0 to 4.8 nm), and their blocking temperatures (from 36 to 58 K) increase with the silica template mesopore diameter. Their magnetic properties are compared to those of standard gamma-Fe2O3 nanoparticles of similar size, obtained by coprecipitation in water and stabilized by a citrate coating.     

Fundamentals of melt infiltration for the preparation of supported metal catalysts. The case of Co/SiO2 for Fischer-Tropsch synthesis

We explored melt infiltration of mesoporous silica supports to prepare supported metal catalysts with high loadings and controllable particle sizes. Melting of Co(NO(3))(2)·6H(2)O in the presence of silica supports was studied in situ with differential scanning calorimetry. The melting point depression of the intraporous phase was used to quantify the degree of pore loading after infiltration. Maximum pore-fillings corresponded to 70-80% of filled pore volume, if the intraporous phase was considered to be crystalline Co(NO(3))(2)·6H(2)O. However, diffraction was absent in XRD both from the ordered mesopores at low scattering angles and from crystalline cobalt nitrate phases at high angles. Hence, an amorphous, lower density, intraporous Co(NO(3))(2)·6H(2)O phase was proposed to fill the pores completely. Equilibration at 60 °C in a closed vessel was essential for successful melt infiltration. In an open crucible, dehydration of the precursor prior to infiltration inhibited homogeneous filling of support particles. The dispersion and distribution of Co(3)O(4) after calcination could be controlled using the same toolbox as for preparation via solution impregnation: confinement and the calcination gas atmosphere. Using ordered mesoporous silica supports as well as an industrial silica gel support, catalysts with Co metal loadings in the range of 10-22 wt % were prepared. The Co(3)O(4) crystallite sizes ranged from 4 to 10 nm and scaled with the support pore diameters. By calcination in N(2), pluglike nanoparticles were obtained that formed aggregates over several pore widths, while calcination in 1% NO/N(2) led to the formation of smaller individual nanoparticles. After reduction, the Co/SiO(2) catalysts showed high activity for the Fischer-Tropsch synthesis, illustrating the applicability of melt infiltration for supported catalyst preparation.     

Sodium niobate adsorbents doped with tantalum (TaV) for the removal of bivalent radioactive ions in waste waters

Mesoporous silica containing a large amount of isolated Ti was prepared from an alkoxytitanosiloxane precursor through a hard template method. Isopropoxytris(tris-tert-butoxysiloxy)titanium (((i)PrO)Ti[OSi(O(t)Bu)(3)](3), TS3) was synthesized and TS3 was mixed with mesoporous carbon (CMK-3), a hard template. The mixture was pyrolyzed at 180 °C to form a composite consisting of titanosilica and the hard template. After calcination at 600 °C for the removal of the carbon template, the titanium species were not transformed to anatase TiO(2), proved by DR-UV-Vis, FTIR, XPS, and XRD, while the ESR results indicated the presence of isolated Ti. The mesoporous structure was verified by SEM, TEM, and N(2) adsorption. The Si/Ti ratio of the product was consistent with that of the precursor. All the results show that the material prepared from the precursor is ordered mesoporous silica containing a large amount of isolated Ti in the frameworks. The use of well-defined alkoxytitanosiloxane precursor leads to the formation of mesoporous silica with exactly controlled composition of titanium with neither loss of Ti nor transformation to anatase.     

Novel coassembly route to Cu-SiO2 MCM-41-like mesoporous materials

A series of mesostructured Cu-SiO2 composites have been synthesized with sodium metasilicate (Na2SiO3) and cuprammonia nitrate (Cu(NH3)4(NO3)2) respectively used as Si and Cu sources. The synthetic procedures were conducted at room temperature, and cetyltrimethylammonia bromide was used as a template. Under our experimental conditions, ordered mesoporous Cu-SiO2 composites could be obtained with a copper content up to 16.8 wt %. Average pore diameters (2.80-3.15 nm), wall thickness (1.30-2.20 nm), and specific surface area (1020-690 m2/g) are found to vary linearly with copper content (0-16.8 wt %). Results of thermal gravimetry-differential thermal analysis reveal the collapse temperature of the order structure starts at approximately 1250 K for mesoporous Cu-SiO2 with 16.8 wt % copper content. As indicated by the outcomes of inductively coupled plasma and X-ray photoelectron spectroscopy studies, copper is mainly incorporated inside the pore wall rather than embedded on the wall surface. Copper species strongly interact with silica, and calcination at high temperatures cannot cause phase separation between silica and copper oxide. Cu status in mesoporous Cu-SiO2 composites is similar to that in copper silicate in neighboring structures. Based on the results, a S+ I- I+ I- mechanism is proposed in which copper entities are surrounded by silicon species during synthesis of the mesostructured composite.     

Surface modification to improve the sorption property of U(VI) on mesoporous silica

Polyoxometalates K₇[α-PW₁₁O₃₉]·14H₂O (PW11) modified mesoporous silica (MCM-48) with cubic structure, was prepared by impregnation and calcination methods. The modified mesoporous silica sorbent (PW11/MCM-48) was studied as a potential adsorbent for U(VI) from aqueous solutions. MCM-48 and PW11/MCM-48 were confirmed by X-ray diffraction and nitrogen physisorption techniques. The results indicate the original keggin structure of PW11 and mesoporous structure of MCM-48 are maintained after supporting PW11 on mesoporous silica MCM-48. The effects of contact time, solid-to-liquid ratio (m/V), solution pH and ionic strength on U(VI) sorption behaviors of the pure and modified mesoporous silicas were also studied. Typical sorption isotherms such as Langmuir and Freundlich isotherms were determined for sorption process. The results suggest that the sorption of U(VI) on MCM-48 or PW11/MCM-48 are strongly dependent on pH values but independent of ionic strength. The sorption capacity of PW11/MCM-48 for U(VI) is about ten times more than that of MCM-48.