二氧化钛纳米微粒的制备与光催化活性

本文采用溶液－凝胶法制备了粒径为１０－２０ｎｍ左右的二氧化钛纳米微粒。用ＸＲＤ研究了二氧化钛溶胶的热处理过程,研究表明温度在４７３Ｋ－６７３Ｋ左右ＴｉＯ２向量 粒呈不规整锐钛矿结构,粒径约为１０－２０ｎｍ。在８７３Ｋ左右ＴｉＯ２微粒出现锐钛矿与金红石型混晶结构。     

二氧化钛的尺寸与光催化活性的关系

采用溶胶－凝胶法控制制备了晶粒尺寸从１０ｎｍ到８０ｎｍ的二氧化钛纳米半导体．用光催化降解苯酚作为模型反应，结合ＸＲＤ，ＤＲＳ，ＦＳ等表征手段，研究了纳米ＴｉＯ２的制备条件与其晶粒尺寸和相结构的关系，探讨了纳米ＴｉＯ２尺寸效应对其光催化活性的影响．发现当晶粒尺寸小于１６ｎｍ时，二氧化钛半导体具有了明显的尺寸量子效应．尺寸量子效应对提高ＴｉＯ２光催化降解苯酚的催化活性起了极为重要的作用．     

纳米TiO_2微胶粒的光化反应制备机理及量子尺寸效应

研究了由水相Ｔｉ３＋制备纳米极ＴｉＯ２微胶粒的光化反应机理及反应动力学，给出反应速率方程，讨论了ＴｉＯ２微胶粒的量子尺寸效应，经电镜测试ＴｉＯ２粒子的直径为１５～２５ｎｍ，反应过程中由气相色谱仪监测生成物Ｈ２。     

纳米TiO2微胶粒的光化应制备机理及量子尺寸效应

研究了由水相Ｔｉ＾３＋制备纳米极Ｔｉ＾Ｏ２微胶粒的光化反应机理及反应动力学，给出反应速率方程。讨论了ＴｉＯ２微胶粒的量子尺寸效应，经电镜测试ＴｉＯ２粒子的直径为１５－２５ｎｍ。反应过程中由气相色谱仪监测生成物Ｈ２。     

甲苯气相选择氧化制苯甲醛Ⅲ．V_2O_5／TiO_2催化剂研究

制备了一系列不同Ｖ２Ｏ５负载量的Ｖ２Ｏ５／ＴｉＯ２催化剂并用于甲苯气相选择氧化制苯甲醛．在ＶＴｉ－１０催化剂上，可获得苯甲醛产率１２．０％的最佳结果．利用ＢＥＴ、ＸＲＤ、ＸＰＳ、Ｈ２－ＴＰＲ、Ｏ２－ＴＰＤ－ＭＳ和化学分析法，考察了催化剂的结构和表面氧性质．发现载体ＴｉＯ２上Ｖ２Ｏ５以晶相和高分散态两种形式存在．反应过程中，催化剂中Ｖ４＋和Ｖ５＋可调整到一定比例并趋于稳定，该调整时间约为１００ｍｉｎ．     

溶剂化金属原子浸渍法制备高分散Au/TiO2低温CO氧化催化剂

用溶剂化金属原子浸渍法制备了不同金含量的高分散Ａｕ／ＴｉＯ２催化剂,ＸＲＤ和ＴＥＭ测定结果表明,随着金含量的增加,金颗粒度增大,但直径都在１．８～３．５ｎｍ范围内,ＸＰＳ研究表明上于金属态,Ａｕ／ＴｉＯ２在低温下就显示出较高的ＣＯ知性,３２３Ｋ时ＣＯ的转化率可达到１００％,金颗粒度为１．８ｎｍ的Ａｕ／ＴｉＯ２催化剂活性最高。     

甲苯气相选择氧化制苯甲醛：Ⅱ.V2O5／TiO2催化剂焙烧温度和反应条件探讨

利用ＢＥＴ、ＸＲＤ、Ｈ２－ＴＰＲ，Ｏ２－ＴＰＤ－ＭＳ等测试手段，并结合化学分析方法，研究了焙烧温度对Ｖ２Ｏ５／ＴｉＯ２催化剂结构和性能的影响。同时探讨了Ｖ２Ｏ５／ＴｉＯ２催化剂上较适合于甲苯气相选择氧化的氧浓度和空速。结果表明，催化剂在７７３Ｋ活化，氧浓度７％，空速１４，０００ｈ＾－１时效果较好。     

溶胶—凝胶法制备负载型TiO2膜的研究

本研究采用溶胶－凝胶（Ｓｏｌ－Ｇｅｌ）法制备了负载型ＴｉＯ２膜，并采用ＳＥＭ、压汞等实验手段对Ｔｉ（ＯＨ）４溶胶和ＴｉＯ２膜进行了表征。实验表明：Ｔｉ（ＯＨ）４溶胶制备过程中Ｈ２Ｏ／Ｔｉ＾４＋、Ｃ２Ｈ５ＯＨ／Ｔｉ＾４＋的比值，溶胶在支承管上浸涂的时间、次数以及凝胶煅烧升温速度和煅烧温度均是制备负载型ＴｉＯ２膜的重要因素。最终制得一种无裂纹、２０μｍ厚、孔径分布在５０￣３００ｎｍ之间的负载型ＴｉＯ２     

化学气相沉积法制备的TiO_2薄膜的光学性质及其应用

以ＴｉＣ１４为源物质采用常压化学气相沉积法制备了ＴｉＯ２薄膜。用紫外光谱测定了膜的透过率,进而计算出折光率、消光系数、光学带隙能等光学参数。结果发现,在不同气流量、沉积温度为１００～２５０℃的条件下制备的ＴｉＯ２膜,其折射率在２．１６～２．８２范围内,消光系数在０．０４×１０－３～６．７０×１０－３范围内,光学带隙能在２．８～３．０８ｅＶ范围内。在光催化作用下,ＴｉＯ２膜用于处理苯酚溶液,苯酚的转化率高达５４．０５％。关键词##4化学气相沉积（ＣＶＤ）;;沉积率;;折光率;;消光系数;;光催化     

低温液相合成甲醇及甲酸甲酯用Cu-Cr-M-O催化剂的制备与表征

采用共沉淀法和配合物沉淀法制备了分别添加Ｂａ, Ｍｎ,Ｖ,Ｂｉ,Ｎｉ 和Ｚｎ 的ＣｕＣｒＭＯ三组分催化剂,采用ＢＥＴ,ＸＲＤ和ＴＥＭ 对催化剂进行了表征,并考察了其对合成甲醇及甲酸甲酯反应的活性及选择性． 结果表明,添加第三种金属使催化剂的稳定性及甲酸甲酯选择性有所提高,但使催化活性有所下降． 配合物沉淀法制备的催化剂的比表面积较大,粒径较小． 热分解温度越高,催化剂的比表面积越小． 除ＣｕＣｒＶＯ 催化剂为纳米非晶态之外,其它催化剂均呈晶态． 催化剂的最小平均粒径为３８ ｎｍ , 最大平均粒径为６８ ｎｍ , 属纳米级催化剂．     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.