Room-temperature ferromagnetism in Sn1−xMnxO2 nanocrystalline thin films prepared by ultrasonic spray pyrolysis

Sn_1−xMn_xO₂ (x=0.01-0.05) thin films were synthesized on quartz substrate using an inexpensive ultrasonic spray pyrolysis technique. The influence of doping concentration and substrate temperature on structural and magnetic properties of Sn_1−xMn_xO₂ thin films was systematically investigated. X-ray diffraction (XRD) studies of these films reflect that the Mn³⁺ ions have substituted Sn⁴⁺ ions without changing the tetragonal rutile structure of pure SnO₂. A linear increase in c-axis lattice constant has been observed with corresponding increase in Mn concentration. No impurity phase was detected in XRD patterns even after doping 5 at% of Mn. A systematic change in magnetic behavior from ferromagnetic to paramagnetic was observed with increase in substrate temperature from 500 to 700 °C for Sn_1−xMn_xO₂ (x=0.01) films. Magnetic studies reveal room-temperature ferromagnetism (RTFM) with 3.61×10⁻⁴ emu saturation magnetization and 92 Oe coercivity in case of Sn_1−xMn_xO₂ (x=0.01) films deposited at 500 °C. However, paramagnetic behavior was observed for the films deposited at a higher substrate temperature of 700 °C. The presence of room-temperature ferromagnetism in these films was observed to have an intrinsic origin and could be obtained by controlling the substrate temperature and Mn doping concentration.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Microstructure and electrical properties of Ba0.5Sr0.5TiO3 thin films prepared on copper foils with La2O3 buffer layers

Ba_0.5Sr_0.5TiO₃ (BST) thin films were deposited on copper foils via sol-gel method with La₂O₃ as a buffer layer. The films were processed in almost inert atmosphere so that the substrate oxidation was avoided while allowing the perovskite film phase to crystallize. The existence of a La₂O₃ buffer layer between the BST thin film and Cu foil improved the dielectric constant and reduced the leakage current density of the BST thin film. Meanwhile, the BST thin film exhibited ferroelectric character at room temperature, which was contrast to the para-electric behavior of the film without the buffer layer. Effects of La₂O₃ buffer layer on the crystallizability and microstructure of BST thin films were also investigated.     

Chemical bath deposition of hausmannite Mn3O4 thin films

A low-temperature chemical bath deposition (CBD) technique has been used for the preparation of Mn₃O₄ thin films onto glass substrates. The kinetic behavior and the formation mechanism of the solid thin films from the aqueous solution have been investigated. Structure (X-ray diffraction and Raman), morphological (atom force microscope), and optical (UV-vis-NIR) characterizations of the deposited films are presented. The results indicated that the deposited Mn₃O₄ thin films of smooth surface with nanosized grains were well crystalline and the optical bandgap of the film was estimated to be 2.54 eV.     

Improving the electrical conductivity of CuCrO2 thin film by N doping

N-doped CuCrO₂ thin films were prepared by using radio frequency magnetron sputtering technique. The XRD and XPS measurements were used to confirm the existence of the N acceptors in CuCrO₂ thin films. Hall measurements show the p-type conduction for all films. The electrical conductivity increases rapidly with the increase in N doping concentration, and the maximum of the electrical conductivity of 17 S cm⁻¹ is achieved for the film deposited with 30 vol.% N₂O, which is about three orders of magnitude higher than that of the undoped CuCrO₂ thin film. Upon increasing the doping concentrations the band gaps of N-doped CuCrO₂ thin films increase due to the Burstein-Moss shift.     

Si基铁电Bi3.15Nd0.85Ti3O12多层薄膜的一致取向生长和性能的研究

采用脉冲激光沉积(PLD)技术，利用LSCO/CeO₂/YSZ多异质缓冲层，在Si(100)基 片上成功地制备了c轴一致取向的Bi_3.15Nd_0.85Ti₃O12(BNT)铁电薄膜.利用X射线衍射(XRD)和扫描电镜(SEM)分析测定了薄膜的相结构 、取向和形貌特征，考察了沉积温度和氧分压对BNT薄膜微结构、取向和形貌的影响，确定 了BNT薄膜的最佳沉积条件.对在优化的条件下制备得到的BNT薄膜的C-V曲线测试得到了典型 的蝴蝶形曲线，表明该薄膜具有较好的电极化反转存储特性.最后讨论了BNT薄膜铁电性能与 薄膜取向的相关性. 关键词： 3.15Nd_0.85Ti₃O₁₂')" href="#">Bi_3.15Nd_0.85Ti₃O₁₂ 铁电薄 膜 多层异质结 脉冲激光沉积     

Preparation and photo-induced superhydrophilicity of composite TiO2-SiO2-In2O3 thin film

In this work, TiO₂-SiO₂-In₂O₃ composite thin films on glass substrates were prepared by the sol-gel dip coating process. X-ray diffraction (XRD), X-ray fluorescence spectroscopy (XRF) and X-ray photoelectron spectroscopy (XPS) were used to evaluate the structural and chemical properties of the films. UV-vis spectrophotometer was used to measure the transmittance spectra of thin films. The water contact angle (WCA) of thin films during UV/vis irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that fabrication of composite film has a significant effect on transmittance and superhydrophilicity of TiO₂ films.     

TiO2 nanoparticle thin film deposition by matrix assisted pulsed laser evaporation for sensing applications

The MAPLE technique has been used for the deposition of nanostructured titania (TiO₂) nanoparticles thin films to be used for gas sensors applications. An aqueous solution of TiO₂ nanoparticles, synthesised by a novel chemical route, was frozen at liquid nitrogen temperature and irradiated with a pulsed ArF excimer laser in a vacuum chamber. A uniform distribution of TiO₂ nanoparticles with an average size of about 10 nm was deposited on Si and interdigitated Al₂O₃ substrates as demonstrated by high resolution scanning electron microscopy-field emission gun inspection (SEM-FEG). Energy dispersive X-ray (EDX) analysis revealed the presence of only the titanium and oxygen signals and FTIR (Fourier transform infra-red) revealed the TiO₂ characteristic composition and bond. A comparison with a spin coated thin film obtained from the same solution of TiO₂ nanoparticles is reported. The sensing properties of the films deposited on interdigitated substrates were investigated, too.     

Structural and electrical properties of (Na0.85K0.15)0.5Bi0.5TiO3 thin films deposited on LaNiO3 and Pt bottom electrodes

(Na_0.85K_0.15)_0.5Bi_0.5TiO₃ thin films were deposited on LaNiO₃(LNO)/SiO₂/Si(1 0 0) and Pt/Ti/SiO₂/Si(1 0 0) substrates by metal-organic decomposition, and the effects of bottom electrodes LNO and Pt on the ferroelectric, dielectric and piezoelectric properties were investigated by ferroelectric tester, impedance analyzer and scanning probe microscopy, respectively. For the thin films deposited on LNO and Pt electrodes, the remnant polarization 2P_r are about 22.6 and 8.8 μC/cm² under 375 kV/cm, the dielectric constants 238 and 579 at 10 kHz, the dielectric losses 0.06 and 0.30 at 10 kHz, the statistic d_33eff values 95 and 81 pm/V. The improved piezoelectric properties could make (Na_1−xK_x)_0.5Bi_0.5TiO₃ thin film as a promising candidate for piezoelectric thin film devices.     

La0.3Sr0.7TiO3模板层对Pb(Zr0.5Ti0.5)O3薄膜的铁电性能增强效应的研究

通过sol-gel法在Si (111) 基片上分别制备了LaNiO₃(LNO)底电极和LaNiO₃/La_0.3Sr_0.7TiO₃ (LNO/LSTO)底电极.然后采用sol-gel 方法，在两种衬底上分别制备了Pb (Zr_0.5Ti_0.5)O₃ (PZT)铁电薄膜.XRD分析表明，两种PZT薄膜均具有钙钛矿结构，且在LNO底电极上的PZT薄膜呈(100) 择优取向，而在LNO/LSTO底电极上的PZT薄膜呈随机取向.铁电性能测试表明，相对LNO衬底上制备的PZT薄膜，在LNO/LSTO底电极上制备的PZT薄膜的剩余极化强度得到了有效的增强，同时矫顽场也增大.介电常数和漏电流的测试表明，LNO/LSTO底电极上制备的PZT薄膜具有大的介电常数和漏电流. 关键词： PZT薄膜 铁电性 漏电流 0.3Sr_0.7TiO₃')" href="#">La_0.3Sr_0.7TiO₃     

Optical and electrical properties of Y2O3 thin films prepared by ion beam assisted deposition

Y₂O₃ thin films were deposited by ion beam assisted deposition (IBAD) and the effects of fabrication parameters such as substrate temperature and ion energy on the structure, optical and electrical properties of the films were investigated. The results show that the deposited Y₂O₃ films had less optical absorption, larger refractive index, and better film crystallinity with the increase of substrate temperature or ion energy. The as-deposited Y₂O₃ films without ion-beam bombardment had larger relative dielectric constant (?_r) and the ?_r decreased with time even over by 40%, while the ?_r of films prepared with high ion energy had less changes, only less than 3%. Also, with the increase of ion energy, the electrical breakdown strength and the figure of merit increased.     

Studies on electrodeposited As2S3 thin films by double exposure holographic interferometry technique

Arsenic trisulphide (As₂S₃) thin films have been deposited onto stainless steel and fluorine doped tin oxide (FTO) coated glass substrates by electrodeposition technique using arsenic trioxide (As₂O₃) and sodium thiosulphate (Na₂S₂O₃) as precursors and ethylene diamine tetracetic acid (EDTA) as a complexing agent. Double exposure holographic interferometry (DEHI) technique was used to determine the thickness and stress of As₂S₃ thin films. It was observed that the thickness of the thin film increases whereas film stress to the substrate decreases with an increase in the deposition time. X-ray diffraction and water contact angle measurements showed polycrystalline and hydrophilic surface respectively. The bandgap energy increases from 1.82 to 2.45 eV with decrease in the film thickness from 2.2148 to 0.9492 μm.     

Influence of postdeposition annealing on structural properties and electrical characteristics of thin Tm2O3 and Tm2Ti2O7 dielectrics

We describe the structural properties and electrical characteristics of thin thulium oxide (Tm₂O₃) and thulium titanium oxide (Tm₂Ti₂O₇) as gate dielectrics deposited on silicon substrates through reactive sputtering. The structural and morphological features of these films were explored by X-ray diffraction, X-ray photoelectron spectroscopy, secondary ion mass spectrometry, and atomic force microscopy, measurements. It is found that the Tm₂Ti₂O₇ film annealed at 800 °C exhibited a thinner capacitance equivalent thickness of 19.8 Å, a lower interface trap density of 8.37 × 10¹¹ eV⁻¹ cm⁻², and a smaller hysteresis voltage of ∼4 mV than the other conditions. We attribute this behavior to the Ti incorporated into the Tm₂O₃ film improving the interfacial layer and the surface roughness. This film also shows negligible degrees of charge trapping at high electric field stress.     

Oxygen pressure dependent electroresistance in La0.9Sr0.1MnO3 thin films grown by laser molecular beam epitaxy

We report here studies on the influence of oxygen pressure on the electroresistance behavior of La_0.9Sr_0.1MnO₃ thin films fabricated by laser molecular beam epitaxy. It was found that the film deposited at lower oxygen pressure shows larger c-axis parameter, higher resistance, and more distinct electroresistance. These results reveal that the electroresistance of manganite thin films can be tuned by the conditions of film fabrication. Supported by the National Natural Science Foundation of China (Grant No. 10334070) and the National Key Basic Research Program of China (Grant No. 2004CB619004)     

The influence of the number of pulses on the morphological and photoluminescence properties of SrAl2O4:Eu,Dy thin films prepared by pulsed laser deposition

The current work reports on the influence of the number of laser pulses on the morphological and photoluminescence properties of SrAl₂O₄:Eu²⁺,Dy³⁺ thin films prepared by the pulsed laser deposition (PLD) technique. Atomic force microscopy (AFM) was used to study the surface topography and morphology of the films. The AFM data showed that the film deposited using a higher number of laser pulses was packed with a uniform layer of coarse grains. In addition, the surface of this film was shown to be relatively rougher than the films deposited at a lower number of pulses. Photoluminescence (PL) data were collected using the Cary Eclipse fluorescence spectrophotometer equipped with a monochromatic xenon lamp. An intense green photoluminescence was observed at 517 nm from the films prepared using a higher number of laser pulses. Consistent with the PL data, the decay time of the film deposited using a higher number of pulses was characteristically longer than those of the other films. The effects of laser pulses on morphology, topography and photoluminescence intensity of the SrAl₂O₄:Eu²⁺,Dy³⁺ thin films are discussed.     

Structural characterization of La0.9Ba0.1MnO3/Y-ZrO2 film by X-ray diffraction

Perovskite manganite La_0.9Ba_0.1MnO₃(LBMO) films were deposited on (0 0 1)-oriented single crystal yttria-stabilized zirconia (YSZ) substrate by 90° off-axis radio frequency magnetron sputtering. The film thickness ranged from 10 nm to 100 nm. Grazing incidence X-ray diffraction technique and high resolution X-ray diffraction were applied to characterize the structure of LBMO films. The LBMO film mainly consisted of (0 0 1)-orientated grain as well as weakly textured (1 1 0)-orientated grain. The results indicated that an amorphous layer with thickness of about 4 nm was formed at the LBMO/YSZ interface. The strain in LBMO film was small and averaged to be about -0.14%. The strain in the film was not lattice mismatch-induced strain but residual strain due to the difference in thermal expansion coefficient between film and substrate.     

Characterization of electrodeposited Bi2S3 thin films by holographic interferometry

Optical non destructive evaluation methods, using lasers as the object illumination source, include holographic interferometry. It is widely used to measure stress, strain, and vibration in engineering structures. Double exposure holographic interferometry (DEHI) technique is used to determine thickness and stress of electrodeposited bismuth trisulphide (Bi₂S₃) thin films for various deposition times. The same is tested for other concentration of the precursors. It is observed that, increase in deposition time, increases thickness of thin film but decreases stress to the substrate. The structural, optical and surface wettability properties of the as deposited films have been studied using X-ray diffraction (XRD), optical absorption and contact angle measurement, respectively. The X-ray diffraction study reveals that the films are polycrystalline with orthorhombic crystal structure. Optical absorption study shows the presence of direct transition with band bap 1.78 eV. The water contact angle measurement shows hydrophobic nature of Bi₂S₃ thin film surface.     

Optical properties of ITO/TiO2 single and double layer thin films deposited by RPLAD

Indium tin oxide (ITO) and titanium dioxide (TiO₂) single layer and double layer ITO/TiO₂ films were prepared using reactive pulsed laser ablation deposition (RPLAD) with an ArF excimer laser for applications in dye-sensitized solar cells (DSSCs). The films were deposited on SiO₂ substrates either at room temperatures (RT) or heated to 200-400 °C. Under optimized conditions, transmission of ITO films in the visible (vis) range was above 89% for films produced at RT and 93% for the ones deposited at higher temperatures. Increasing the substrate temperature from RT to 400 °C enhances the transmission of TiO₂ films in the vis-NIR from about 70% to 92%. High transmission (≈90%) was observed for the double layer ITO/TiO₂ with a transmission cut-off above 900 nm. From the transmission data, the energies gaps (E_g), as well as the refractive indexes (n) for the films were estimated. n ≈ 2.03 and 2.04, respectively for ITO films and TiO₂ film deposited at 400 °C in the visible region. Post-annealing of the TiO₂ films for 3 h at 300 and 500 °C was performed to enhance n. The refractive index of the TiO₂ films increases with the post-annealing temperature. The direct band gap is 3.6, 3.74 and 3.82 eV for ITO films deposited at RT, 200, and 400 °C, respectively. The TiO₂ films present a direct band gap of 3.51 and 3.37 eV for as deposited TiO₂ films and when annealed at 400 °C, respectively. There is a shift of about 0.1 eV between ITO and ITO/TiO₂ films deposited at 200 °C. The shift decreases by half when the TiO₂ film was deposited at 400 °C. Post-annealing was also performed on double layer ITO/TiO₂.     

Optical and hydrophilic properties of Cr doped TiO2-SiO2 nanostructure thin film

Cr doped TiO₂-SiO₂ nanostructure thin film on glass substrates was prepared by a sol-gel dip coating process. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to characterize the structural and chemical properties of the films. A UV-vis spectrophotometer was used to measure the transmittance spectra of the thin film. The hydrophilicity of the thin film during irradiation and storage in a dark place was measured by a contact angle analyzer. The results indicated that Cr doping has a significant effect on the transmittance and super-hydrophilicity of TiO₂-SiO₂ thin film.     

Morphology and natural wettability properties of sol-gel derived TiO2-SiO2 composite thin films

Previous studies suggest that granular interfaces induce a natural and persistent super-hydrophilicity in TiO₂-SiO₂ composite thin films deposited by sol-gel route. This effect enables to consider self-cleaning applications that do not require a permanent UV exposure, whereas such a permanent exposure is necessary for pure TiO₂ films. In this study, TiO₂-SiO₂ composite thin films have been deposited from a TiO₂ anatase crystalline suspension and different SiO₂ polymeric sols. Wettability studies show that a suitable control of the TiO₂-SiO₂ mixed sol formulations noticeably enhances persistence of the natural super-hydrophilicity in composite films. It is shown that, beside granular interface effects, modifications in the composite film morphologies can noticeably influence wettability properties.